Factory restore does not restore Win7 but Win8

Similar Questions

• Windows 8 does not read DVD but CD runs without any problem

  Original title - I habe upgrade to windows 8 way back but my DVD player does not read DVD but CD runs without any problem

  DVD stalk does not read DVDs but reading the CD with no problems. Even in my computer drive shows as CD drive type.

  Hi Rohan,

  I suggest you try the steps suggested by AtishayMSFT dated dated March 6, 2012 at the following link:

  http://answers.Microsoft.com/en-us/Windows/Forum/hardware/DVD-drive-not-recognized-in-Windows-8/ad546c20-b916-4AD5-9858-52e10610ee14

  Note: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article: back up the registry in Windows 7

• On the computer, it does not load XP but goes to the XP start and says: NVRD32.sys file not found

  On start-up the computer, it does not load XP but goes to starting XP, and says NVRD32.sys file not found. I have to go up to xp home line manually and it load. How to fix the problem, so he starts xp automatically without entering start xp
  Thank you

  Posing for the PC model, you show that you do not know the answer, it was a software problem, but you're right, it's a Dell.
  In any case, I found the answer elsewhere, must with the boot.ini file on XP

• I have HP E809a Officejet of 7000 series, my printer does not print color but black

  I installed the new ink, but the printer does not print color but black. When I do trobleshooting he information I get is all works well.

  Assuming that you have installed the printer using the HP cd or the installation software full on HP site review the HP print settings/diagnosis and test the printing options, or help from HP, all available from the HP shortcuts installed with their software.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=UK&DLC=&sw_lang=&product=3883002

• DVD player does not read DVDs but reads CDs only.

  my hp compaq 420 core2 duo dvd player does not read DVDs but only reads the CD. How can I fix this, please help me with the correct answer.

  It will probably replace the drive. There is more than one laser in there: one for each function. You can go bad without the other goes wrong.

  608141 001

  Above is the part number for the DVD burner. I couldn't find one on eBay.  In here is a online:

  http://www.mydvddrives.com/replacement-for-HP-Compaq-608141-001-SATA-CD-DVDRW-DVD-RAM-drive-burner-LightScribe-52029

  Replacement is easy. Remove one screw on the bottom and drag the old hunt and replace it with the new drive.

• WebLogic: when call a URL excelfile does not open MSExcel but flat html

  WebLogic call an excel file of the URL does not open MSExcel but flat html
  
  Hello
  
  I get differences between FORMS 10 g / YOU and FORMS 11 / WLS
  When to call an Excel with web.showdocument
  
  --------------------------------------------------------------------------------------
  in 10g AS10g
  the call
  Web.showdocumen ('http://MyAS10_Server/myFormsMapping/myExcelfile.xls, _blank);
  
  Opens a Windows box
  to decide
  Open with (MSExcel)
  or
  Download and save as a file
  
  
  --------------------------------------------------------------------------------
  in WLS 10.3.5 / FORMS 11.1.1.4
  the call with webcache Port 8090 and Port 8888 SST
  
  Web.showdocumen ('http://MyWLS_Server:8090/myFormsMapping/myExcelfile.xls, _blank);
  
  quickly open the excel file in the browser in html Format
  
  --------------------------------------------------------------------------------------
  
  How to get the same way in WLS as before as a 10 g,
  need change the (mimetype?) when open excel?
  
  respect of

  There was a post in the past which makes some interesting claims.

  Why o why have we not able to do a faq to these things?

  Like they said, I can't find any mimemappings.properties.

  more information:
  "An alternative is to create a file mimemappings.properties the entire domain to define a type for the '.myext' extension. Start the WebLogic administration console and go to the domain--> for Web Applications. Set a value for the "Mime mapping file' if the field is empty. Next, create the file. Should be the format of the contents of the file: = mime-type extension

  Example:
  myext = text/plain
  WBMP =

  The first entry above defines a new file extension 'myext' and sets the type of 'text/plain '. The second entry above means a 'wbmp' file extension that already exists in the default values. Setting the value vacuum removes the mapping.

  Another solution is to configure the MIME type in the web.xml file. Update the Web application's web.xml file, by adding a element to map the new extension to a suitable MIME type.
  "

  last post * thank you!
  Display a help file (*.chm) Windows of a session of 11g of forms
  Matthew

  I had a similar problem with my environment, Forms 11 g with Weblogic. Files with the extension ".rtf" displayed as text gross when I used the port 8888 (SST). Using the port 9001 (WLS_FORMS), it worked. I have four servers managed in the group, so I have to use port 8888.

  After a few days and many tests, changing configurations and restart services, I found the file "mimemappings.properties" of Weblogic. In fact, in my environment, I had to create the file with the line 'rtf = application/rtf' and restart the Weblogic Server. It worked for me.

  Using the Console of Administration Weblogic, in Configurations of domain / Web Applications, see the parameter "Mime mapping file. The file must exist in the folder "$DOMAIN_HOME/config. More information on this file, you can find in http://download.oracle.com/docs/cd/E11035_01/wls100/schemaref/security/http.www.bea.com.ns.weblogic.920.domain/types/web-app-containertype.mime-mapping-file.html.

  I hope it can help you!

  Ricardo Ravazzolo

  Published by: Lake on Sep 9, 2011 10:59

• Restore to factory content does not work correctly

  Help, please!

  I had a 'Blue Screen of Death' on my T42. I decided to use the button "Access IBM" and to "restore the contents of the factory.

  However, once I did this, different devices (listed in the Device Manager) were not working properly. The its (SoundMax) did not work at all (no sound from the computer). The INTEL 2200BG wireless network card does not work. I even installed the driver (downloaded on the IBM Web site) and install the driver. Then the noise started working (but the volume buttons on the keyboard do not always work.) I have a little trouble getting all the devices to work.

  I had restored the contents of factory once before, and I don't remember the devices does not. Shouldn't this operation set all devices to work correctly?

  OK, I solved my problem.

  It turns out that the procedure to "Restore the content of the plant" is not complete. A lot of the never executed restore procedure and so many devices were missing (and many pre-installed software).

  I don't know why this happened, but my best guess is that I have accidentally hit the "ESC" key or something like that and who may have quit the restore process.

• Factory reset does not work

  I have a Nighthawk X 8 I bought two months ago. Up to today (March 7), it worked fine. Today I came home and found it did not work. I tried to access it via routerlogin.net, nothing worked. I tried factory reset using a toothpick about 5 times now, but it doesn't seem to matter. my computer (connected via ethernet) does not allow me to set it up, and I'm not wireless. The power button remains mostly orange, but it seems resets automatically once in a while.

  I tried to call customer service, but they hung up on me while starting to record my router midsentence. I'm afraid I'll need a RMA number, unless someone can tell me why reset does not work. I tried to do it for 8 seconds (directions say that), longer, several times, while it was turned on, turned off, both, etc. None of this helps.

  If I can't get the factory reset to work, is there a way to set up an RMA number without appeal? After the initial CS hangup, I was told that I would be on the phone for an hour, waiting for relief.

  I ended up doing an RMA number. Got my new unit and it is working fine now. If all goes well, he will not leave in like the last 2 months...

• W530 factory recover does not

  I just had a new w530 and trying to upgrade the HDD to a crucial SSD.

  I ran the thing 'to create a recovery disk' ThinkVantage to burn a factory restore disc. This burn has worked, and this is the only dvd that he asked to burn.

  When I pass on the hard drive and run the recovery DVD, it has been running for a little bit and then asks: "Please insert the drivers recovery disk and applications" 1 in drive D:

  It has only an OK option, which, once clicked complains that it doesn't have the good disk.

  I went to the original hard drive and tried to make another dvd. He finished burning and check, but at the end of the process, it says "an unexpected error has occurred (rc = 9). I have tried this twice and these results in the same message "Please insert disk recovery applications and drivers.

  In case someone else has this problem and is looking for the solution, you just keep trying until you burn successfully all 4 DVD

• Accessories HomeKit does not at home, but work outside.

  Hello

  I recently got a new Signal of Hunter ceiling fan, which is one of the first active HomeKit fans. I went through the installer on my iPhone 7 more for the fan about 20 times. Each time, installation works and the fan is controllable for about 1-5 minutes each time. Then the two buttons for the fan and light are starting to appear 'No response' on them. By clicking on the buttons, surprise, has no effect on the fan or light.

  I have my Apple TV (4th generation) Setup as a hub. I also tried setting to the top of my iPad as a hub. Nor has helped get my fan work. However... today we were shopping, and I happened to pull up the control center. I noticed that Photonics and fan buttons is no longer says "No response" and typed a. After a few seconds, the fan button said it was now on. Then I tried the light. Same positive reaction. I played with them a few moments and everything seemed to work... except that I couldn't be sure, because, you know, I was not at home.

  So, when I got home, I tried again... back to 'No response' on the buttons. What the devil? So I then turned off the wifi on my phone and guess what? The "No Response" disappeared and the fan and light work.

  So there is something when my iphone is on my own wifi network, it cannot speak to the HomeKit accessories. That makes no sense at all. Why would it be? Is there something on my router I need to unlock it (even if I looked and did not find anything which is blocked).

  I contacted the support team for the fan again. But I'm starting to think it's something with the iPhone, not the fan. Oh, and HomeKit opening on the iPad does not work internally either.

  Thanks in advance for any help you can provide.

  Bob

  Greetings, U2SockMonkey!

  To review your post, you have configured your Signal Hunter ceiling fan in your HomeKit and use your AppleTV and iPad as hubs. Your iPhone 7 more on iOS 10.0.2 intermittently becomes a message 'no response' when you try to control your ceiling fan with it but it worked fine while you were away from home. It is apparently only at home and I'll be happy to help you to get this working properly.

  If your iPhone, iPad or iPod touch connects to a Wi-Fi network - I found that iOS devices and a home network can stop talking to each other. Follow the steps in this article to ensure that your home's Wi - Fi signal is strong and consistent.

  Take care and thank you for using communities of support from Apple!

• I want to use a Terminal Airport Express to extend network provided by my Fios router/modem without going through another airport base.  Is there a way to do this?  I understand that Apple does not support this, but surely there must be a way to do this.

  Can someone tell me how to set up an Airport Express Terminal to expand Network provided by my Fios router/modem without going through an airport as a base?  I understand that apple does not support this use, but my applecare Advisor said it's possible.  Thank you!

  Unfortunately, your AppleCare Advisor is wrong if he or she has told you that an AirPort Express to extend wireless signal of a Fios router/modem.

  Function of "Extend a wireless network" Apple is an exclusive feature that was designed by Apple engineers to extend the signal from another wireless only router from Apple. Thus, the AirPort Express... or any other router Apple besides... would not be able to extend wireless a Fios network.

  SO... you have the possibility to locate the Airport Express where it is needed... And... Connect it to the Fios router/modem with a permanent, wired Ethernet cable connection, then the AirPort Express can 'extend' in this way.

  Or... If you are ready to add a second AirPort Express, connect the first near Fios modem/router with an Ethernet cable, then the second Airport Express could extend the signal first Express wireless.

  Another way to say the same thing, is that if you want an Apple AirPort router to extend wireless network... then you need two Apple routers to achieve this goal.

• No matter what I do, email does not turn off, but it is fine.

  I get this at startup:
  "Could not initialize component of application security. The most likely cause is problems with the files in the directory of the profile of your application. Please check that this directory has no restriction of read/write and your hard disk is not full or close to full. It is recommended that you exit the application and correct the problem. If you continue to use this session, you may see incorrect application behavior when you access security features. »
  I check this problem 3 times, reinstalled the program once and the program still does not send e-mails any of my four email accounts. Mail comes in fine.
  Don't know what to do next - but I need to send a quick email.
  Thank you
  King of the JT

  Please read the information on this link to see if it helps solve the problem: http://kb.mozillazine.org/Could_not_initialize_the_browser_security_component

• Satellite NB10t-A - Webcam does not work after update Win8.1

  Hello

  I have recently upgraded to Windows 8.1 and then my Webcam does not work... I checked if I have the driver in Device Manager but I couldn't find it. I don't know how can I fix what I was looking for driver thosiba Web site but got no results.
  Can someone help me?

  Thank you

  The BIOS usually contain an option to enable and disable the internal webcam.
  Go to the BIOS by pressing F2 and then check if the webcam is enabled.

• Satellite P50-A-144 - FN + z key does not work after update Win8.1

  Hello
  a couple of months ago with windows 8, which became 8.1 with w. update, I bought PC toshiba laptop SATELLITE P50-A-144.
  Since then, fn + z key does not work, it says that light keyboard turns off whenver I press it.

  How could I solve this problem? It's my OCD tingle.

  Thanks for all the replies :D

  Strange. Something like that shouldn't happen. I updated my machine, but everything works fine.

  I don't know if this will help, but try to reinstall the driver of Toshiba system and function key utility Toshiba.

  You should find it on the download page of Toshiba - http://www.toshiba.eu/innovation/download_drivers_bios.jsp
  Check it out.

• Satego x 200-BIOS does not detect SSD but windows 7 for OS usage

  need help here, I got the latest bios 2.50 and my bios does not detect the SSD but an I start windows 7 from my hard drive it is detected and I want to use the ssd as boot drive, please help

  Hello

  Which SSD drive you have exactly?
  I also think it s a compatibility problem between the HARD disk controller (motherboard) and the current SSD drive.

  So you should check if you have the latest firmware of the SSD drive and if it of possible, try another disc SSD of a friend, for example.

  By the way: have you tried to load the default settings in the BIOS?