Fan update

Similar Questions

• M6 k010dx: fan update

  I have a hp m6 k010dx and I was wondering if there was a way I could upgrade my moter fan or if there was an improved heat sink that I could get my computer becomes extremely hot until nere the screen where are the spekers.

  I can deal with it, but I was wondering about an possibule upgrade.

  Thank you

  Hello

  No, that came with your laptop is the only one you have. You can clean vents off dust and debris.

  http://support.HP.com/us-en/document/c01657439

  Manual - Page 19, 20: http://h10032.www1.hp.com/ctg/Manual/c03935332

  Concerning

  Visruth

• Fan making a lot of noise but no update BIOS

  Hello everyone.

  For a few months now my HP Touchsmart 600-1140sc began to go crazy with the fan when I start it the night before (I think it's the sleep less :-) mode he's going in when I click on the button in the upper right of the computer!) and sometimes when I shut it down completely and starts as well. This is usually resolved by turning off the computer (NOT restart), wait a few seconds, then starts again. It is quite annoying to have to do all the time, as now the fan usually does 75% of the time.

  I tried all the steps of the Danish guide for what might solve this (power settings, clean the fan, update of the graphics driver) except to update my BIOS. The reason I didn't is because there is no available BIOS update on HP site support! My OS is Windows 7 64 bit
  What should I do? I don't want to have to replace my entire computer since I have to downgrade to a computer much worse than it is already (for purposes of games that it's bad at least ;-))

  Kind regards

  Luttii

  Bump. I really need help with this, please

• start-up problems for my pc

  Desktop computer: product not. KQ497AA-ABA

  Operating system: Windows Vista

  Question: Anyone know how to solve startup problems when you have to push the button on top of the computer to turn on and turn off a lot of times to get the computer to enter the blue HP screen (for the evacuation start, recovery of the system etc.) and the load? In addition, my computer won't stay on more than 10 or 15 minutes. He stops and try to reboot, leaving stuck on the blue screen again. Of course, I'd appreciate any help!

  Thank you wb2001, can I suggest a bios update to this topic because it set some themal and restart situations:
  
  Fix the version 5.43/improvement:
  
  -Improves the thermal performance of the system.
  -Curve of fan updates for support of the processor.
  -DECIDED problem with the system seems to hang when restarting if a HP Personal Media Drive is connected.
  -DECIDES that problem with the system suspended when 7 GB of RAM is installed.
  -Updates of the Diagnostic tools hardware v4880.05.
  
  Download link:
  http://ftp.HP.com/pub/softlib/software11/COL34762/PV-86212-1/sp46442.exe

• Create computer custom - thoughts?

  Hi all!

  I'm trying ito find the best computer for my price (about $2,000) that can give me fast performance when working with HD DSLR images in first Pro CS5 and After Effects (I'm working on wedding videos that can vary from a few long minutes to 40 minutes)

  I had a different discussion open before on a graphics card, but I thought I'd start a new thread to see if none of the experts here agree with the specifications I've done for a new PC.

  It's CyberPowerPC.com:

• Module of Extension USB internal: 6 USB PORTS expansion module internal NZXT
• Extra case Fan updated: Default case fans
• CPU: Intel® Core™ i7-980 3.33 GHz Six carrots 12 M Intel Smart Cache LGA1366
• Venom push Overclocking of fast and effective factory: No Overclocking
• Cooling fan: 510LC Asetek liquid cooling system 120MM radiator & fan (cooling performance improvement + extreme silence to 20dBA) (standard single 120MM fan)
• Motherboard: * (3 - Way SLI Support) MSI X58A-GD45 Intel X 58 Chipset SLI/CrossFireX Triple-Channel DDR3 ATX Mainboard w / 7.1 Audio, eSATA, GbLAN, USB3.0, SATA-III, RAID, IEEE1394a, 3 PCIe Gen2, 3 PCI PCIe X 1 & 1 (all certified venom OC)
• Memory: Module memory Triple channel DDR3/1600 MHz 24 GB (4GBx6) + [225] (Corsair XMS Memory with heat spreader sink Gaming)
• Video card: NVIDIA GeForce GTX 570 1.2 GB 16 X PCIe (Superclocked EVGA) video card
• Freebies: FREE game - Dungeon Siege 3
• 2 video card: None
• 3 video card: None
• Dedicated PHYSX card: None
• Several settings video card: Non-SLI/CrossFireX Mode not supported multiple monitors
• Power Supply Upgrade: 800 Watts - XtremeGear Gaming Power Supply - Quad SLI Ready
• Hard drive: 30 GB OCZ Vertex Series 2.5 inch SATA II Solid State Disk Gaming (30 GB x 2 (60 GB capacity) Performance extreme Raid 0 + [72])
• Data hard disk: 2 TB (2TBx1) SATA-III 6.0 GB/s 64 MB Cache 7200 RPM HARD drive (HDD)
• Disk hard cooling fan: None
• External hard drive (USB3.0/2.0/eSATA): None
• USB key: None
• Optical drive: LG WH10 - LS30K 10 X Blu - Ray Burner internal Super Multi + [46] (Siver color + [9])
• Sound: ON-BOARD 7.1 HIGH DEFINITION AUDIO

I would greatly appreciate any adjustment entry/suggested someone of you has to offer!  Thank you!

Call us http://adkvideoediting.com/ . They specialize in custom build Assembly machines, are very knowledgeable and great support.

Your Setup program contains elements which are nearby without a performance POV value and lack of certain elements which will be severely harming you.

Liquid cooling is a waste of money (unless the overclocking to the extreme) and a beast to install.

Your food is only mediocre.

Your choice startup disk is too small and one expensive SSD. Better get a 320 HDD Samsung F4 classic.

You need an extra couple of HDD to use the 980 to its potential.

You may need to consider a dedicated raid controller.

You may need a case to put all that things, unless you prefer the free items on your desktop.

• Fan MacBook Air updated according to Sierra

  Given that I have improved my old MacBook Air from two years to Sierra this weekend, it is now heats and the fan turns after a few hours of work. He almost never did this before the update. Any ideas?

  Denise

  reset your SMC

  Reset the management system (SCM) controller on your Mac - Apple Support

• Fan number after updating to Mac OS Sierra

  Hello people, as many of you all know, Apple released macOS Sierra. The updating of this new operating system, I have been met through rather annoying problem for me. It seems that my fan is not eager to be quiet as it has been in the previous operating system. The computer is usually warmer than its normal temperature. At first I thought it was a software problem during the upgrade. I came back to El Capitan, the computer runs cool. Fresh installed copay of Sierra and the computer becomes extremely hot and fan running constantly at high SPEED. It's quite strange to me, so I was wondering if someone else running Sierra also have this problem. I have little friends of mine Sierra both running on their MacBook Air machines, but they have the same problem. Any help or suggestion? Thank you

  Hi SC909,

  It seems that your computer is running more hot than usual, and as such, the fan is at the top all the time. I would say that resetting the SMC on your computer:

  Reset the management system (SCM) controller on your Mac.

  Thank you for using communities of Apple Support.

• MacOs Sierra update causes crazy fan

  After MacOS Sierra update, my macbook air cooling fan (2014 at the beginning) became crazy! Its almost running all the time while I barely remember his work before.

  Try resetting the SMC http://support.apple.com/kb/ht3964

• iMac fan sleep after security update

  The fan on my iMac 27 inches (mid 2011) will not stop when the computer is put to sleep. I am running OS X Yosemite 10.10.5 version. Graphics Intel Core i5 at 2.7 GHz. card processor: AMD Radeon HD 6770 M 512 MB.

  I think it has something to do with security update 2016-004 (awords of content security of OS X El Capitan v10.11.6 and Security Update 2016-004 - Apple Support)

  I just updated the other day and since the fan will not go to sleep when I put the iMac in mode 'sleep'. I've also updated iTunes and Safari, but I doubt that this has nothing to do with it.

  The SMC reset and reset the PRAM was conducted without success.

  Any ideas?

  Thank you

  Sometimes it takes several MSC resets for the reset to work. Please do the reset SMC 2 - 3 times and then repeat the test.

• Yesterday, I did the 2016-002 security update and also updated Safari 9.1. My MacBook Pro was working fine before, but now fan runs loudly and Activity Monitor wrote in red "Safari Web content (not answer) with an impact energy of 99.8.» How to fix?

  trouble after Safari 9.1 update - noisy fan - warning of "Safari Web content (not responding)."

  Click the Apple, top left, and then select force quit, ForceQuit Safari in the list.

  Restart Safari.

• irreversible bios update made noisy fan (8710p, 8710w, 8510p, 8510w, fan, F.20, F.0E)

  Hey.

  I just want to share my experience with the update of the bios on my computer hp 8710w laptop and talk to HP support. I've updated F.0E to F.20 and after that this fan went wild. In windows 7 it works very well every boots 2 / 3, or more. All fans of time runs fast, no matter what the system load and temperature are. What makes the portable noisy.

  I used to use linux and it just fan slow down after spinning up to cool the system. It is really something that you want to have, because it becomes a noisy vacuum cleaner with an excellent machine and quiet.

  I have enough evidence to assume that the problem was caused by the update of the bios. First of all, it started exactly after the bios update when nothing else has been changed. Secondly, 5 years ago I had a very similar laptop (8710p) and when I have updated the bios to F.0F, it's the same thing, but I fortunately downgraded the bios and everything was back to normal. In addition, reported others on the internet and these discussion forums.

  Now with the update of F.20... There is no way to downgrade. It's embarrassing: HP has released a update this feature breaks... and there is no way back (except the replacement of the card system, which is expensive for laptops out of warranty).

  I was the cat and then talk on the phone with HP support. They are not really very close to professional. First, they said that my windows 7 is not officially supported and should I install xp or vista. I have xp installed specially for them, and which consumes a lot of time. Of course, nothing has changed. And they actually all drivers for windows 7...

  The best advice of hp support has been trying to install all previous versions of the bios. I reported a failure on each one, then only, they found in the description of the version F.20 could not be downgraded. After reading the forums here for 15 minutes, I knew much more technical support on my laptop and the question, lol.

  After talking with me for a time very long (like 3 or 4 hours) and say that I try to restart my machine, or start with the Windows key + b, etc., they said that my laptop is out of warranty, and there is nothing that they can help me with.

  I confess that the laptop is out of warranty... but only suffers from the update of the official firmware that cannot be downgraded. Yes, I know I'm supposed to buy a new replacement HP laptop. But... This look bad.

  Now, I'll get a replacement bios chip, programmed with the previous version of the bios and soldered to the motherboard...

  Hello to the guys at HP support. They are nice people who try to be useful, they don't know anything about their products :-)

  Hello programmers to the HP bios... Please... Please be better, please learn that bugs can be corrected.

  Problem solved! :-D

  I downgraded to F.0E

  Find a difference in the photos below:

  BEFORE:

  

  AFTER:

  

• Satellite Pro P200-15W: after Bios Update 1.90 incredibly noisy fan

  Hi, I have a Toshiba Satellite Pro P200-15W, I recently made an update to BIOS version 1.9 and seems to have been a big mistake.
  After restarting the computer, I had a lot of software deconfig and the fan has become incredibly noisy.

  I have the problem with the Toshiba Vista registration software, I get this message: "registration of Vista has stopped working". I read other discussions, I don't want to just disable it in the start.ini file, I would actually solve the problem if there is a way.

  Is there a way to change the configuration of fans? I read a post from Toshiba on another model of laptop that has had the same problem of noisy fans after an update of the BIOS, they gave that a solution with a new version of the BIOS, is there a way to reverse the BIOS to the previous version? (recovery CD will be useful for this purpose)?

  See you soon

  Edgard

  Hello

  It seems that the picture of the fan was changed and renewed in the new version of BIOS, and so fans run fall.
  Why the table fan has been changed?

  Well, usually something like this is necessary to improve the reduction of the internal temperature while the CPU and GPU are running with maximum performance.
  This helps to prevent the equipment from damage!

  Usually, the recovery CD formats the whole HARD drive (partitions too) and installs only the image of Toshiba on the notebooks of HARD drive.
  The image contains the OS, drivers and additional software and has nothing to do with the BIOS update.
  But you can try to recover the laptop to see if you can solve the problems of software as "Vista record"!

  If you want to reverse the BIOS, you will need to contact the ASP in your country!

  Sorry, but all I can suggest.

  Best regards

• Satellite Pro P200-15W: update according to BIOS 1.9 fans walk all the time

  I have a Satellite Pro P200-15W. After recently running the BIOS update to version 1.9, the fans started running all the time and are extremely loud. Also, he did weird things for Firefox, Thunderbird and NAV.

  I would like to "Uninstall" the update of the BIOS if possible. I found [this link: http://askiris.toshiba.com/ToshibaSupportSite/search.do?cmd=displayKC&docType=kc&externalId=1080 89xml & sliceId = & dialogid = 24408215 & stateId = 0% 200% 202 4406262] who treats the restore running CD.

  If I run this CD, which will certainly restore the BIOS to the previous version?

  Is there a less destructive way (ie: that does not erase the hard drive)?

  Thank you

  Ben

  Post edited by: cannboys

  Hello

  It seems that the picture of the fan was changed and renewed in the new version of BIOS, and so fans run fall.
  Why the table fan has been changed?

  Well, usually something like this is necessary to improve the reduction of the internal temperature while the CPU and GPU are running with maximum performance.
  This helps to prevent the equipment from damage!

  > would like to "Uninstall" the update of the BIOS if possible. I found this link that explains the running restore CD. If I run this CD, which will certainly restore the BIOS to the previous version?
  > Is there a less destructive way (ie: that does not erase the hard drive)?

  Usually, the recovery CD formats the whole HARD drive (partitions too) and installs only the image of Toshiba on the notebooks of HARD drive. The image contains the OS, drivers and additional software and has nothing to do with the BIOS update.
  But you can try to recover the laptop to see if you can solve the problems of software!

  If you want to reverse the BIOS, you will need to contact the ASP in your country!

  Sorry, but all I can suggest.

  Best regards

• HP Envy: Updated, now Fan always on top

  It used to be that if the fan was running upstairs, I closed just a few apps and it would immediately slow down and be almost inaudible.

  Now the fan is always on (and the air coming out is hot enough) even when no apps are open, and the room is 62 degrees.

  I did all the standard things:

  • Updated the BIOS
  • Cleaned all vents
  • Disabled indexing
  • Off many other features
  • Turned Coolsense works

  I have to just live with the extra noise?

  Al
  
  TouchSmart HP Envy 17
  Windows 10 worm 1607

  I went to this page:

  https://www.wintips.org/how-to-fix-Svchost-exe-netsvcs-memory-leak-or-high-CPU-usage-problems

  Finished and disabled the windows update and a few other things, and now the CPU usage dropped by 20 percent to about 2 percent.

  I don't know exactly which thing solved, but now the fan is nice and quiet.

• Satellite R630-155 - fan is too loud and SSD update

  I am the owner of a Toshiba Satellite R630-155 (Core i5-480). My problems are:

  1. the fan is too loud and never stops. In normal operation (navigation and General Office work) there is a constant high pitch noise which is audible three to four meters in a desktop - high load environment, you just can't take it anymore! The fan never stops... even when you do nothing...

  2. the heat is a big problem. The bottom of the laptop is overheated constantly and I have to place on my desk so that the lower left corner is outside the table, so it can breathe fresh air from below - otherwise, the temperature rises and the (noisy) fan is unable to follow. When I work with the laptop sitting on a couch, I place a thick book between the laptop and my legs. The book must be thick (more than one inch) with hard covers, otherwise the heat going through the book!

  3. last (but not least, I will mention the biggest problems here) that's the problem with the installation of the SSD. I bought a used Corsair F80 (80 GB SSD) from a friend, but I was unable to use it with the Toshiba - BIOS not detect the disc. I tried to install all the latest updates for portable and SSDS but I had no success. Then I put the disc and I bought a brand new Zalman 128 GB SSD (SSD0128N1 Sandforce) but I had exactly the same problem. I contacted my local support Toshiba and after much conversation, the only answer I got is that the laptop is not compatible with these SSDS, and it is acceptable by Toshiba and not their problem. They told me that if I need an SSD upgrade I cannot go for the Toshiba SSD that is installed on the portege series, which is sold by Toshiba for a ridiculously expensive price - about $500 for 128 GB. I contacted the European support center and I got the same exact answer. I searched the Internet and found someone else with exactly the same problem with a Corsair 128 GB SSD - he concluded that the laptop detects the SSD after ten to twenty resets. I tried and it was true - after a lot of restarts the detected disk Zalman laptop and I was able to successfully install Windows 7, but the process is unacceptable. Also the drive is rated by the sites official at the speed of an OCZ Vertex 2 128 GB (and a little better), but when I ran a cue point in the Toshiba, the results I got were less than half of the advertised speed. Same reference in another machine of the same disc, resulted in the announced speeds.

  Shame for Toshiba...-beautiful design and portability, but all the rest is a big flaw. Their support in non-existent and they do not appreciate their customers. According to me, they stole my money and I will never buy a Toshiba laptop again.

  Sorry for the big message, but I need, I warn potential customers. Can anyone help me with any of these problems? You also have the same problems?

  To follow...

  Hey Buddy,

  With regard to the issue of fan and the heat: you did it BIOS update? A friend told Satellite R630 too and he told me that the fan with the new BIOS version 2.10 activity is reduced. In addition, the laptop is colder than before so I recommend to install this update. You can download the update of the BIOS here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  But before you start the update of the BIOS, you should consider the following tips:
  -Run update as an administrator only
  -Unzip all files from zip archive before launching the update file
  -Close all running programs as the antivirus and firewall
  -Make sure the battery is fully charged

  With regard to the SSD it s still a little complicated to install 3rd party products and no one can guarantee that these parts would not work. You're always on the side safely with original spare parts from Toshiba.

  All you can do is to install the new firmware for SSDS and hope that it works, but who knows maybe the BIOS update will help you also in this case ;)