Filter BPDU to vSwitch

Hello

Network administrator implements the VLAN for a new ESXi host.

He asks me to activate the BPDU filter on vSwitch all. I searched for the BPDU filter and know how to do. However, it seems that is not commonly used.

In this case, we need to activate the BPDU filter on vSwitch?

answer to your question is here following Ko, it must be done by the host base.

VMware KB: Understand the function BPDU filter in vSphere 5.1

Similar Questions

Filters BPDU

Is it possible to implement the BPDU filtering in ESXi? I can do it on a standard switch or do I need a distributed switch? I can do it on a distributed switch NSX?
Thank you

BDPU filtering is a host to the scale and not a vSwitch parameter. As such, it works with vSwitches, standard and distributed. There is no special license or add-on as NSX required, to enable it, just set the host Net.BlockGuestBPDU to 1. This will block all frames BDPU sent from any guest on any vSwitch on the host.

For more information, see the following articles:

VMware KB: Understand the function BPDU filter in vSphere 5.1

vSphere 5.1 - VDS news - filter BPDU - VMware vSphere Blog - VMware Blogs

STD + Cisco 8024f

Hello

I am trying to install

SwA (cisco WS-C3560G-24PS)

SWB (cisco WS-C3560G-24PS)

CFC (8024f)

SWD (8042f)

I stacked CFC & swd (such as CFCS).

My links are so

SWC 1/0/1 & 1/0/2 stacked related swc2/0/1 & 2/0/2. These are my stackable ports!

SwA gi0/16-online swc1/0/24

SWB gi0/16-online swc2/0/24

SwA has 2 links for EFA

bits of Cisco

SwA

spanning tree mode rapid pvst
spanning tree etherchannel guard misconfig
spanning tree extend id-system
VLAN spanning tree priority 4096 1,19,201-211

interface GigabitEthernet0/16
Description link Trunk at CFC
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 201-208 250
switchport mode trunk
! Shutdown

Interface Port - Channel 1
Description safe Inter-Switch
switchport trunk encapsulation dot1q
switchport mode trunk
bandwidth 2000000
!
interface GigabitEthernet0/1
Description safe Inter-Switch
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group mode 1 on

interface GigabitEthernet0/24
Description safe Inter-Switch
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group mode 1 on

SWB

spanning tree mode rapid pvst
spanning tree etherchannel guard misconfig
spanning tree extend id-system

interface GigabitEthernet0/16
Description link Trunk to swd
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 201-208 250
switchport mode trunk
! Shutdown

Interface Port - Channel 1
Description safe Inter-Switch
switchport trunk encapsulation dot1q
switchport mode trunk
bandwidth 2000000
!
interface GigabitEthernet0/1
Description safe Inter-Switch
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group mode 1 on

interface GigabitEthernet0/24
Description safe Inter-Switch
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group mode 1 on

on the 8024f

Configure
database of VLAN
VLAN 201-208 250
VLAN 1 1 routing
output
spanning tree mst mode

spanning tree mst configuration
instance 1 Add vlan 1
output
spanning tree mst configuration
instance 201 add vlan 201
output
spanning tree mst configuration
instance 202 Add vlan 202
output
spanning tree mst configuration
instance 203 Add vlan 203
output
spanning tree mst configuration
instance 204 add vlan 204
output
spanning tree mst configuration
instance 205 add vlan 205
output
spanning tree mst configuration
instance 206 Add vlan 206
output

spanning tree mst configuration
instance 207 Add vlan 207
output
spanning tree mst configuration
instance 208 Add vlan 208
output
spanning tree mst configuration
instance of 250 Add vlan 250
output
spanning tree mst configuration
name "SWC".
output

spanning tree mst configuration
revision 1
output

interface Te1/0/24
full duplex
Description "CFC to swa.
switchport mode trunk
switchport trunk allowed vlan 201-208 250

interface Te2/0/24
full duplex
Description "swb swd."
switchport mode trunk
switchport trunk allowed vlan 201-208 250
output

research on the 8024f I see this on the port. Note it has not received all BPDU packets!

SWC

show the spanning tree tengigabitethernet 1/0/24

Te1/0/24 port permit Port Ext. cost: 20000
State: Forwarding role: designated
Identification of the port: 128.24 int. shipping cost: 20000
Fast port: no Protection from root: No.
Designated the bridge priority: 32768 address: D067. E5AF.1268
Identification of the designated port: cost of access road designated 128,24: 0
Root regional CSE: 80:00:D0:67:E5:AF:12:68 CST Port cost: 0
Root Guard..................................... FAKE
Loop Guard..................................... FAKE
TCN Guard...................................... FAKE
Portfast auto... TRUE
Port of time since the last reset counters... 0 day 19 h 12 min 57 sec
BPDU: 34588 sent, received 0

See the spanning tree 2/0/24 tengigabitethernet

Te2/0/24 port permit Port Ext. cost: 0
Status: Disabled role: disabled
Identification of the port: 128.48 int. Shipping costs: 0
Fast port: no Protection from root: No.
Designated the bridge priority: 32768 address: D067. E5AF.1268
Identification of the designated port: 128.48 designated path cost: 0
Root regional CSE: 80:00:D0:67:E5:AF:12:68 CST Port cost: 0
Root Guard..................................... FAKE
Loop Guard..................................... FAKE
TCN Guard...................................... FAKE
Portfast auto... TRUE
Port of time since the last reset counters... 0 day 18 h 41 min 36 sec
BPDU: 689 sent, received 0

see the summary of spanning tree

Spanning Tree Adminmode... Activated
Spanning Tree Version... IEEE 802. 1 S
BPDU guard mode... People with disabilities
BPDU flood mode... People with disabilities

Mode filter BPDU. People with disabilities
Configuration name... CFC
Review configuration level... 1
Digest configuration key... 0x46511ebde89aab9201e08f03a0f29719
Format of configuration selector... 0

When I check there are 2 roots 1 on the valleys and 1 on the cisco... the cisco work

SwA

SH interface spanning tree g0/16

Role of VLAN m Prio.Nbr cost Type
------------------- ---- --- --------- -------- --------------------------------
VLAN0201 Desg FWD 4 128.16 P2p
VLAN0202 Desg FWD 4 128.16 P2p
VLAN0203 Desg FWD 4 128.16 P2p
VLAN0204 Desg FWD 4 128.16 P2p
VLAN0205 Desg FWD 4 128.16 P2p
VLAN0207 Desg FWD 4 128.16 P2p
VLAN0208 Desg FWD 4 128.16 P2p
VLAN0250 Desg FWD 4 128.16 P2p

SH detail g0/16 interface spanning tree

Port 16 (GigabitEthernet0/16) VLAN0201 is designated transfer
Port path costs 4, 128, Port identifier 128.16 Port priority.
Designated root a priority 4297, address 001e.bde0.ea00
Designated bridge has priority 4297, address 001e.bde0.ea00
Designated port ID is 128.16, designated path cost 0
Timers: 0 delay the message age 0, forward, hold 0
Number of transitions to the transmission of State: 1
Type of connection is from point to point by default
BPDU: 34489 sent, received 4

Show bridge spanning tree

Hello Max Fwd
VLAN ID time bridge age Dly Protocol
---------------- --------------------------------- ----- --- --- --------
VLAN0001 4097 (4096, 1) 2 20 15 rstp 001e.bde0.ea00
4115 VLAN0019 (4096, 19) 2 20 15 rstp 001e.bde0.ea00
VLAN0201 4297 (4096, 201) 2 20 15 rstp 001e.bde0.ea00
4298 VLAN0202 (4096, 202) 2 20 15 rstp 001e.bde0.ea00
VLAN0203 4299 (4096, 203) 2 20 15 rstp 001e.bde0.ea00
VLAN0204 4300 (4096, 204) 2 20 15 rstp 001e.bde0.ea00
4301 VLAN0205 (4096, 205) 2 20 15 rstp 001e.bde0.ea00
VLAN0207 4303 (4096, 207) 2 20 15 rstp 001e.bde0.ea00
4304 VLAN0208 (4096, 208) 2 20 15 rstp 001e.bde0.ea00
VLAN0209 4305 (4096, 209) 2 20 15 rstp 001e.bde0.ea00
Rstp 001e.bde0.ea00 2 20 15 VLAN0250 33018 (32768, 250)

I have no installation of STD on the cisco... It's the first time I touch STD

I guess if I get BPDUS be seen his will start working

I had found a white paper before 8024f and stp, but as is typical I can't find it now!

OK so finally managed to do work. everything moved to STD.

There is a long and complicated why reason not to use STD wit pvst + (or anything else outside of STDs).

He ha with convergence and how stp manages the VLAN and the lag!

an I had install STD on the two end bang just worked

Configuration port-channel, DTP, disabling

Hi all

I had a problem on the day where I wanted to attach a pile of 3750 x 2 to the network, the core is a 6500.

There was a link configured for the core of the 3750 he had the configuration necessary trunk with BPDUFILTER active

at the end of the base he had the standard configuration of trunk. The link is on the rise and work.

Went to get a second battery for the heart link. Decided that DTC must be turned off at the end of the SWITCHPORT NONEGOTIATE battery

the normal chest on the port configuration on the port channel port joined. Then suddenly the newspapers went crazy and right now, I need

Spanning tree went crazy and started blocking areas of the network to avoid loops. There is STDS running in the network

I had similar errors to this % SW_MATM-4-MACFLAP_NOTIF

I pulled the battery cables and all services affected later came back.

I know that enable the BPDUFILTER option stops at the port to participate in STP.

Please could someone confirm due to the incompatibility of the config on these ports it has this problem or is there something I missed here

Thank you mnay

The BPDU filter is the root of the problem.

You can't have two active rising running without creating a loop, unless they run into a PaGP/LACP-EtherChannel configuration. By having one or two links running with a filter BPDU, spanning Protocol tree on the 6500 didn't know that a link had to be in a deadlock state and he was panicked when MAC addresses on the stack of 3750 began to stir between interfaces.

3750 cross media - stack EtherChannel using LACP, so if you want the resilience of two connections without having to factor in the covering tree branches, it is a good idea to combine the two in a group of channels and have both the 3750 and 6500 treat them as a single logical connection.

If you want to keep them separated, you will need to remove the filters BPDU these ports and leave spanning tree figure things out properly.

Integrate existing network SG200

We have an existing network with a main catalyst switch 4510 and 3560 departmental switches are connected via fiber. Due to the restructuring of the company we can no longer buy us some new 3560's, when something goes wrong, so this week I bought a SG200-26 which I am trying to get on the network.

It is a legacy network that does not set up so my Cisco skills are somewhat limited (another reason for the if SG200 fine), in any case have been watching the configs on the existing switches and trying of correspond to the settings in the configuration SG200 however do not do anywhere! I have the config of the dead switch so I can show what needs to be done, I was wondering if anyone has experience in the degradation of their environment in a similar way and if there was someone who could help?

Peter, the good thing is, it seems that the config is fairly consistent with the SX200. It doesn't look like you guys made anything too special about the 3560.

Here is a snippit of your config

interface FastEthernet0/18

Phone nortel Description

switchport access vlan 32

switchport trunk encapsulation dot1q

switchport trunk vlan native 32

switchport trunk allowed vlan 16.32

switchport mode trunk

spanning tree portfast trunk

spanning tree enable bpduguard

This particular port config looks like she embodies most of your work that you have cut out for you.

I use Microsoft device emulator for example

https://www.Cisco.com/assets/Sol/SB/Nikola_GUI/SG_200-50P_v1_1/config/home_sx200.htm
- Connect to the switch IP address
- Browse VLAN MANAGEMENT-> create a VLAN
- Create the necessary VLAN ID, it looks like you have a certain 16, 32, 64, 254,
- Once VLANS are created them navigate VLAN MANAGEMENT-> Port Vlan Membership
- Choose the port on which you want to configure, in the example snippit 18 port, click the port 18 radio button then scroll down and click on JOIN VLAN
- This will open a new window, on your 18 port config looks like vlan 32 originated. The only command I noticed is there is "allowed vlan 32" essentially what actually a port marked for the vlan native. On the right column where it says 1up, select this option and then use the arrow to the left to slide on
- Then on the left panel to choose 32, below where it says that marking, labeled and trying to make it is the PVID also choose 16, select the tag ensure 16 is not defined as a PVID then and apply this
- The port should read 16 t, 32tp
- To configure the setting of tree cover for this example navigate SPANNING TREE-> parameter of the interface of STP
- Choose the port 18 then scroll down and click on change
- Spanning port fast shaft comes in the terminology as edge port, change the port from edge of the car to allow
- Then change the bpdu filtering handling (it's about the same as the bpdu guard)
- Apply the settings
That's all what you can associate up to based off this port config. The switch does not have a so the closest bpdu guard, you can do is to filter bpdu. Globally configured BPDU Guard is designed to disable (disable-err) all ports enabled portfast should they ever receive BPDU frames. While preventing the switch to send BPDU frames on ports that are enabled with the portfast BPDU filter.

It also appears on the config of your vlan 1 is inactive and your vlan 254 is the vlan management. If this is the case, you can change the vlan by default of the switch to 254.

Don't forget to save the running configuration to the startup configuration.

I hope that's enough "translation." Let me know if you have any other questions.

-Tom
Please mark replied messages useful

Is the spanning tree bpdu filtering on the 5548 "bpdufilter default spanning-tree portfast'

It seems to me as "the protocols spanning-tree bpdu filtering" on the 5548 the same "spanning-tree portfast default bpdufilter" on the switches of the series N - is that correct? If this is not the case, what is the equivalent command to 'spanning-tree portfast default bpdufilter?

Ken

They lead to the same result, just with a little different method. N-series bpdufilter search all ports configured for portfast and disables the transmission and reception of BPDUS on these interfaces. With the looks of 5548 bpdufiltering for ports with covering weight tree disabled. There is not a command on the 5548 that will search interfaces in portfast mode and filter the BPDU.

vSwitch not allowing a host connection

Hello
I have a basic configuration of 2 VMhosts
4 vSwitches
4 physical networks all mutually exclusive
vSwitch0 connects 4 NICs per host to a pile of Cisco 3750
vSwitch1 connects 4 network cards for iSCSI storage area network connected to the Dell Powerconnect stack
vSwitch2 connects 2 NICs for the vMotion Gigabit switch
vSwitch3 is a single network adapter that is connected to a single Cisco switch to shared resources with other Cisco switches on corporate network separate
Everything seems fine, except that only 1 hosts may never have vSwitch3 connected with an active link.
If I connect the two hosts vSwitch3 vmnic6 (physically) to the Cisco switch is that both, they go down, or we stay down until the two are unplugged and then plugged the premiera remains active.
For me, I guess it looks like in there are some protocols spanning-tree loop rear blocking ongoing, but this could not be the case if the vSwitch never sends and BPDU?
I do not understand why vSwitch0 can have 4 network cards on the two hosts connected to a stack of 3750 and work very well, but only one NIC on vSwitch3 to a single Cisco switch allows only one link on one host to be active at a given time?
The 3750 battery has spanning tree portfast enabled on all ports, and I have admin access to that stack.
I do not have administrative access to the single Cisco switch on the network of the company so I can't check the config, but would turn config be the problem here?

The ports are configured for 100 MB on the switches.

I managed to get in touch with the architect of the network and he indicated that the port security has been enabled on all ports.

See article.

http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC&externalID=1002811

He has deleted them for two ports since then.

I'll test after hours tonight and I hope that it is the cause of the problem.

Thanks again to all.

PS the script to display the virtual machines that reside on a specified vSwitch

In the process of migration of virtual machines to vSphere 5 Cisco Nexus 1000v running. However, I need to generate a list of VMS still residing on the old vSwitch in a datacenter.
I know the powerpack VMware display the VMCount, but it would be useful to be able to run the script every morning and send the list of virtual machines residing on the old vSwitch automatically.
VCenter 5 running.

You have probably more than 1 portgroup with this name

Try it like this
```
## name of portgroup whose VMs to get info on $strPortgroupName = "MyPortgroupName"
## Get the View object of the Network of the given name, then get the View objects of the VMs on that network, and return the VMs' names Get-View -Id (Get-View -ViewType Network -Property Name,VM -Filter @{"Name" = $strPortgroupName} | %{$_.VM}) -Property Name | select Name
```

Script for vSwitch change security settings

Going to start working on this script, but if someone knows, is one year, I'd be interested. Trying to create a script that changes the vSwitch 'Change of address' security settings and "forged passes" to "Reject" to all on the host's vSwitches. I would like the script to turn to a CSV with a list of ESX servers, so that the script should authenticate directly on the ESX Server. Thank you.

Yes, you need a header row in the CSV file

Move invites him outside of the loop, something like this

$rootpassword = Read-Host -AsSecureString -Prompt "Enter the root password"

Import-Csv "C:\esxnames.csv" -UseCulture | %{
    Connect-Viserver $_.Name -user root -password $rootpassword 

    $esx = Get-View -ViewType HostSystem -Filter @{"Name"=$_.Name}
    $NetworkSystem = Get-View $esx.ConfigManager.NetworkSystem
    foreach ($sw in $NetworkSystem.Networkconfig.Vswitch){
        $swspec = $sw.spec
        $swspec.policy.security.AllowPromiscuous=$false        $swspec.policy.security.ForgedTransmits=$false        $swspec.policy.security.MacChanges=$false        $NetworkSystem.UpdateVirtualSwitch($sw.name,$swspec)
    }

    Disconnect-VIServer -Server $_.Name -Confirm:$false}

I can't print after upgrade to Mac OS Sierra (error "Unable to filter")

I can't print after upgrade to MacOS Sierra, always shown "cannot filter. I use AirPrint for Epson L355. Tried to reset the printer settings, uninstall and then install the printer, always in vain 'filter '.

I think it has something to do with MacOS Sierra 10.12.1 Beta (16B2333a). Help, please!

Update to the Sierra officially released

Printer "filter failed" for macOS Sierra?

Hi all

I have upgraded my iMac and MacBook Pro with the new macOS Sierra and did not have a lot of problems until recently. As my exams are approaching, I print on my printer, Canon E560 comments. However, recently, some pages may not be printed and printing stops. He said "stopped -"filter"failed", and I can't find a way to solve this problem. I did this experiment several times, and in early printing, it is said immediately that the filter is not on my computer, but continues to print up to a page where it stops. Some pictures on the already printed pages are distorted. Is this related to the Sierra macOS? This is true for my two computers. I replaced the cartridges of ink, but in vain. I've also sent cannon on it, but they take a lot of time to answer me.

I have another printer on the floor in my house, which is of my fathers. So, I tried printing with it, but words have white lines through it, for some pages. This shows that it may be a problem with the document or the software, macOS Sierra 10.12.

For two printers, it seems that the content of the pages is pushed down as well.

Thank you very much

Ethan

Have you looked for a new driver for your printer? Canon are responsible for updating the drivers for their products to ensure that they are compatible with the new operating system

Automate the cells of the filter to another table based on two columns

Hello

What I'm trying to do is: filter multiple cells to a new table. In this example, I want that all students (column 'lidnr', 'city', then the first 7 columns) with 1 teacher in the 'First' column to be copied into the table 'teacher 1'. The same goes for students per 1 teacher in the column "second". I know it can be done with the help of the filter and the copy paste, but I would like to know if this can be automated, because there are many more tables in my actual document.

I've been using maybe to think the search formula but he can't give me more than one result, the result must be unique.

Thank you very much for your help.

Kind regards

Kim

Hi Kim,

The usual way to do this is to add an index for each table for which column the data is to be copied.

Here is an example of preliminary. Improvements after return from the light of day.

Triangles of error on the last row of T1 are thanks to the formula out of data to search for. Easily fixed.

Order of the names is different from your example, which is grouped by day numbers. Build lists in the desired order, rethinking the index calculations.

Course index calculations use the formula below, entered in Table 1::L2 and thre to the rest of the blue full cells filled.

L2: = IF (OR (RIGHT($H2,1) = RIGHT (L$ 1.1) RIGHT($J2,1) = RIGHT (L$ 1.1)), MAX(L$1:L1) + 1"," ")

Data recovery on the Table T1 is well done by the following formula, entered in A2 and down and B2 and filled and down-filled.

A2: = INDEX (array 1::A, CORRESPONDENCE (LINE (−1, 1 Table): $L, 0))

B2: = INDEX (array 1::B, CORRESPONDENCE (LINE (−1, 1 Table): $L, 0))

More tomorrow (actually, later today).

Since the upgrade to Sierra, Mail will not recognize or filter spam

I'm having the problem where almost nothing goes in my junk e-mail folder. I rechecked my mail spam filtering preferences and I have it configured to enable filtering and move the Junk to junk e-mail folder. Those are the only two boxes checked. That the mail comes, I have systematically report as junk, but no matter how many times I do that junk mail is still not reported as spam in the future, nor is it place in my spam box. I really don't know what to do at this point.

RE-INDEX YOUR SPOTLIGHT CACHE FILES

In the Apple menu, choose System Preferences.

* Click on the projector.

Make this mail and Messages is enabled on the results tab of research.

* Click on the Privacy tab.

* Drag your player to the list. Wait a few minutes.

* Remove the item you added.

* Projector will be re - index the content of the element that you initially dragged to the list.

Begin the recovery disk by pressing command + R during restart.

Open disk utility and run first aid for your Macintosh HD (internal) and volumes given by you.

The reboot: click on Mac OS X Installer in the upper left, and click on Quit in Mac OS X Installer. Click Startup disk. Click your primary hard drive, and then click Restart.

When you restart Spotlight will re-index your entire drive.

accept this warning). When you type your password, it will look like nothing is typed. It's normal. Once you type your administrator password, press return.

SUMMARY:

Depending on your Mac and the contents of his hard drive, the re-indexing may take several hours. This night is a good option if you have a large drive.

Open the activity monitor in Applications/Utilities and type md in the search filter. You should see the files of mdworker process. This shows Spotlight indexing of your files. Until this process is complete, Spotlight will not know the contents of your discs and will not send mail.

With Mali leave...

Go to the library to the user

Scrolling in containers

Delete com.apple.mail folder.

Scrolling in mail > V4 > MailData

Find the 3 files with envelope in the name.

Delete the files.

Log Out under the Apple in the Menu bar

Open a session

Open mail

Mail will be re-index your files.

It is possible, that you will also need to re-index your Contacts.

Let me know if it helps.

Message error "arrested -"filter"has failed."

After upgrading to Mac OS Sierra, when you attempt to send a test print my Epson Stylus Photo 2200, I get the message error "stop -"filter"failure" in my print queue.

I have left clicked on the printer-> error log menu item, and I have the following in the error log.

E [27/Sep / 2016:10:04:40-0500] [Job 3] Job is stopped due to errors in filter; For more details, see the error_log file.

D [27/Sep / 2016:10:04:40-0500] [Job [3] the following messages have been saved since 10:04:38 to 10:04:40

D [27/Sep / 2016:10:04:40-0500] banner of start-up [Job 3] adding page 'none '.

D [27/Sep / 2016:10:04:40-0500] [Job 3] queued on the "EPSON_Stylus_Photo_2200" by "derekberube".

D [27/Sep / 2016:10:04:40-0500] file [Job 3] seized automatic...

D [27/Sep / 2016:10:04:40-0500] [Job 3] request file type is application / vnd.cups - banner.

D [27/Sep / 2016:10:04:40-0500] [Job 3] file of type application / vnd.cups - banner in queue 'derekberube '.

D [27/Sep / 2016:10:04:40-0500] [Job 3] end banner add page 'none '.

D [27/Sep / 2016:10:04:40-0500] [Job 3] time to processing = 1474988678

D [27/Sep / 2016:10:04:40-0500] [Job 3] 3 filters for task:

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgbannertopdf (application / vnd.cups - banner to application/pdf, cost 33)

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster (application/pdf in the application / vnd.cups - raster, cost 100)

D [27/Sep / 2016:10:04:40-0500] [Job 3] /Library/Printers/EPSON/InkjetPrinter2/Filter/rastertoescpII.app/Contents/MacOS /rastertoescpII (application / vnd.cups - raster to printer/EPSON_Stylus_Photo_2200, 0 cost)

D [27/Sep / 2016:10:04:40-0500] [Job 3] job-sheets = none, none

D [27/Sep / 2016:10:04:40-0500] [Job 3] argv [0] = "EPSON_Stylus_Photo_2200".

D [27/Sep / 2016:10:04:40-0500] [Job 3] argv [1] = '3 '.

D [27/Sep / 2016:10:04:40-0500] [Job 3] argv [2] = "derekberube".

D [27/Sep / 2016:10:04:40-0500] [Job 3] argv [3] = "testprint.

D [27/Sep / 2016:10:04:40-0500] [Job 3] argv [4] = "1".

D [27/Sep / 2016:10:04:40-0500] [Job 3] argv [5] = "AP_ColorMatchingMode = AP_VendorColorMatching AP_D_InputSlot = nocollate com.apple.print.DocumentTicket.PMSpoolFormat=application/pdf com.apple.print.JobInfo.PMJobName = testprint com.apple.print.PrinterInfo.PMColorDeviceID... n. = 23775 com.apple.print.PrintSettings.PMCopies... n = 1 com.apple.print.PrintSettings.PMCopyCollate... b. com.apple.print.PrintSettings.PMFirstPage... n = 1 com.apple.print.PrintSettings.PMLastPage... n = 2147483647 com.apple.print.PrintSettings.PMPageRange... a.0... n = 1 com.apple.print.PrintSettings.PMPageRange... a.1... n. = 2147483647 fit-to-page media = letter requested by pserrorhandler = standard job-uuid=urn:uuid:8781dff0-21e9-31ef-5b09-534d193452be job-originating-name of host = localhost to-date-time-create = date-time-to-processing = time-to-creation" time processing 1474988678 = 1474988678 = document-name-supplied testprint PageSize = letter»

D [27/Sep / 2016:10:04:40-0500] [Job 3] argv [6] = "/ private/var/spool/cups/d00003-001.

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [0] = "< CFProcessPath >".

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [1] = "CUPS_CACHEDIR = / private/var/spool/cups/cache '.

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [2] = "CUPS_DATADIR = / usr/share/cups.

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [3] = "CUPS_DOCROOT = / usr/share/doc/cups.

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [4] = "CUPS_FONTPATH = / usr/share/cups/fonts.

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [5] = "CUPS_REQUESTROOT = / private/var/spool/cups.

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [6] = "CUPS_SERVERBIN = / usr/libexec/cups.

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [7] = "CUPS_SERVERROOT = / private/etc/cups.

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [8] = "CUPS_STATEDIR = / private/etc/cups.

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [9] = "HOST = / private/var/spool/cups/tmp".

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [10] = "" PATH = / usr/libexec/cups/filter: / usr/bin: / usr/sbin: / bin: / usr/bin ""

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [11] = "[email protected]".

"D [27/Sep / 2016:10:04:40-0500] [Job 3] envp[12]="SOFTWARE=CUPS/2.2.0 ".

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [13] = ' TMPDIR = / private/var/spool/cups/tmp ".

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [14] = "USER = root"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [15] = "CUPS_MAX_MESSAGE = 2047"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [16] = ' CUPS_SERVER = / private/var/run/cupsd.

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [17] = "CUPS_ENCRYPTION = IfRequested"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [18] = 'IPP_PORT = 631'

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [19] = "CHARSET = utf-8"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [20] = "LANG = fr_FR. UTF - 8"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [21] = "APPLE_LANGUAGE = en - en"

"D [27/Sep / 2016:10:04:40-0500] [Job 3] envp[22]="PPD=/private/etc/cups/ppd/EPSON_Stylus_Photo_2200.ppd ".

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [23] = "RIP_MAX_CACHE = 128 m"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [24] = "' CONTENT_TYPE = application / vnd.cups - banner" "

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [25] = "DEVICE_URI = 0 usb://EPSON/Stylus%20Photo%202200?serial=L5602021107061925"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [26] = "PRINTER_INFO = EPSON Stylus Photo 2200"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [27] = "PRINTER_LOCATION = MacBook Pro Derek Berube\"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [28] = "PRINTER is EPSON_Stylus_Photo_2200"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [29] = "PRINTER_STATE_REASONS = none"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [30] = "CUPS_FILETYPE = document"

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [31] = "" FINAL_CONTENT_TYPE = vnd.cups - raster/application ""

D [27/Sep / 2016:10:04:40-0500] [Job 3] envp [32] = "AUTH_I."

D [27/Sep / 2016:10:04:40-0500] [Job 3] Started filter/usr/libexec/cups/filter/cgbannertopdf (PID 2075)

D [27/Sep / 2016:10:04:40-0500] [Job 3] Started filter /Library/Printers/EPSON/InkjetPrinter2/Filter/pdftopdf2.app/Contents/MacOS/pdft opdf2 (PID 2076)

D [27/Sep / 2016:10:04:40-0500] [Job 3] Started filter/usr/libexec/cups/filter/cgpdftoraster (PID 2077)

D [27/Sep / 2016:10:04:40-0500] [Job 3] Started filter /Library/Printers/EPSON/InkjetPrinter2/Filter/rastertoescpII.app/Contents/MacOS /rastertoescpII (PID 2078)

D [27/Sep / 2016:10:04:40-0500] [Job 3] Started backend/usr/libexec/cups/backend/usb (PID 2079)

"D [27/Sep / 2016:10:04:40-0500] [Job 3] Message catalog filename is \"/System/Library/Frameworks/ApplicationServices.framework/Versions/A/Framework s/PrintCore.framework/Versions/A/Resources/English.lproj/cups_apple.strings\.

D [27/Sep / 2016:10:04:40-0500] [Job 3] load_banner(filename=\"/private/var/spool/cups/d00003-001\")

D [27/Sep / 2016:10:04:40-0500] [Job 3] usb: AppleLanguages =-"en - US\".

D [27/Sep / 2016:10:04:40-0500] [Job 3] STATE: + connection-device

D [27/Sep / 2016:10:04:40-0500] [Job 3] looking for \'EPSON Stylus Photo 2200\'

D [27/Sep / 2016:10:04:40-0500] [Job 3] open connection

D [27/Sep / 2016:10:04:40-0500] [Job 3] PID 2078 (/Library/Printers/EPSON/InkjetPrinter2/Filter/rastertoescpII.app/Contents/MacO S/rastertoescpII) was arrested with the 206 State (output Interface queue is full)

D [27/Sep / 2016:10:04:40-0500] [Job 3] Tip: try to set the LogLevel "debug" to learn more.

D [27/Sep / 2016:10:04:40-0500] [Job 3] Page = 612 x 792; 9.40 at 603-783

D [27/Sep / 2016:10:04:40-0500] [Job 3] directory ' / Library/Printers/EPSON/CIOSupport/EPSONUSBPrintClass.plugin ' permissions OK (040755/uid = 0/gid = 80).

D [27/Sep / 2016:10:04:40-0500] [Job 3] directory ' / System/Library/Printers/Libraries/USBGenericPrintingClass.plugin ' permissions OK (040755/uid = 0/gid = 0).

D [27/Sep / 2016:10:04:40-0500] [Job 3] load_classdriver(/System/Library/Printers/Libraries/USBGenericPrintingClass.plu gin) (kr:0 x 00000000)

D [27/Sep / 2016:10:04:40-0500] [Job 3] load_classdriver(/Library/Printers/EPSON/CIOSupport/EPSONUSBPrintClass.plugin) (kr:0 x 00000000)

"D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: copy to temp \"/private/var/spool/cups/tmp/0081d57f93b5a\ print file '.

D [27/Sep / 2016:10:04:40-0500] [Job 3] STATE:-connecting-to-device

D [27/Sep / 2016:10:04:40-0500] [Job 3] sending data to the printer.

D [27/Sep / 2016:10:04:40-0500] [Job 3] sent 0 bytes...

D [27/Sep / 2016:10:04:40-0500] [Job 3] STATE: + cups-wait-for-work-over

D [27/Sep / 2016:10:04:40-0500] [Job 3] align for banner 1.

D [27/Sep / 2016:10:04:40-0500] [Job 3] PID 2075 (/ usr/libexec/cups/filter/cgbannertopdf) came out without error.

D [27/Sep / 2016:10:04:40-0500] [Job 3] PID 2076 (/Library/Printers/EPSON/InkjetPrinter2/Filter/pdftopdf2.app/Contents/MacOS/pdf topdf2) came out without error.

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: \"/private/var/spool/cups/tmp/0081d57f93b5a\"has 1 pages.

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: open \"/private/etc/cups/ppd/EPSON_Stylus_Photo_2200.ppd\ file PPD «...»

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: PreferredRotation = - 90

D [27/Sep / 2016:10:04:40-0500] [Job 3] cupsPageSize = [612 792], cupsImagingBBox = [9 40 603 783]

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: width = 612, length = 792, high = 9, low = 40, left = 9, right = 9

D [27/Sep / 2016:10:04:40-0500] [Job 3] cupsWidth = 2970, cupsHeight = 3715

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: languageLevel = 3, mediaBox.size.width = 612, mediaBox.size.height = 792

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: colorspace = 1, bitsPerColor = 8

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: the seller matching mode is turned on and the requested transfer color space is sRGB.

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: skipBytesPerRow = 8

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: bandwidth = 2970, bytesPerRow = 11888, band height = 3715, height = 3715

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: width of the frame = 2970, height = 3715 bitsPerComponent is 8, bitsPerPixel = 32 bytesPerRow = 11888, bitmapInfo = 5, resolution = (360.000000, 360.000000)

D [27/Sep / 2016:10:04:40-0500] [Job 3] HWResolution = [360 360]

D [27/Sep / 2016:10:04:40-0500] [Job 3] ImagingBoundingBox = [9 40 603 783]

D [27/Sep / 2016:10:04:40-0500] [Job 3] margins = [9-40]

D [27/Sep / 2016:10:04:40-0500] [Job 3] PageSize = [612 792]

D [27/Sep / 2016:10:04:40-0500] [Job 3] cupsWidth = 2970

D [27/Sep / 2016:10:04:40-0500] [Job 3] cupsHeight = 3715

D [27/Sep / 2016:10:04:40-0500] [Job 3] cupsBitsPerColor = 8

D [27/Sep / 2016:10:04:40-0500] [Job 3] cupsBitsPerPixel = 24

D [27/Sep / 2016:10:04:40-0500] [Job 3] cupsBytesPerLine = 8910

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: rasterWriteHeader: unable to write the header streams raster: Broken pipe

D [27/Sep / 2016:10:04:40-0500] [Job 3] cgpdftoraster: bytes written for the side 1 = 0, err = 5

D [27/Sep / 2016:10:04:40-0500] [Job 3] PID 2077 (/ usr/libexec/cups/filter/cgpdftoraster) came out without error.

D [27/Sep / 2016:10:04:40-0500] [Job 3] waiting for read thread exits...

D [27/Sep / 2016:10:04:40-0500] [Job 3] PID 2079 (/ usr/libexec/cups/backend/usb) came out without error.

D [27/Sep / 2016:10:04:40-0500] [Job 3] end of messages

D [27/Sep / 2016:10:04:40-0500] [Job 3] printer - state = 3 (idle)

D [27/Sep / 2016:10:04:40-0500] [Job 3] printer-State-message = "Sending data to printer."

D [27/Sep / 2016:10:04:40-0500] [Job 3] - printer-motivation = none

Line 66 # in the above seems to indicate the rastertoescpII utility failed with a status code of 256 and the error message "output Interface queue is full.

Troubleshooting steps

To try to solve this problem, I followed the steps described in the article «problems of printer on your Mac» I have reset the printing system and it does not work. I have also unplugged the printer, deleted the contents of the folder/library/printers/and then plugged the printer into.

You will need to check with Epson to see if there is a new driver for your device compatible with macOS Sierra. The old drivers are not compatible. Even with the new driver, some people state that the error is not fixed :-( YMMV.

Filter for HDR photos

I used to use Aperture but have really achieved by using pictures. It does the job and is improving all the time. I shoot a lot of HDR and also keep the original. Is there a way to filter the only HDR versions and thus have a quick way of removing the non - HDR of same photo versions?

menu, file == > new smart album - photo is HDR

LN

Filter BPDU to vSwitch

Similar Questions

Maybe you are looking for