Find the resources gap visa?

Similar Questions

• Matter of finding the resources function VISA after COM port disconnected

  I have an application in which I use two COM ports for communication, both only is active.

  Between testing a com port gets connected and disconnected dynamically. I am able to connect and disconnect without problem.

  Now after my com port dynamic disconnected, its not visible in device as Manager, but if I search all the com port available using VISA find resource once it disconnects, then dynamic port COM is also visible in the list.

  Name of the USB interface is USB Serial Port and the com port is dynamic which will be disconnected. VI attached

  Any suggestion please

  
  

• Instrument not listed is not in the resource of VISA

  I have a GPIB resource.  He appears in MAX, but not on behalf of the constant resource.  I checked I/O filtering and updated the name of the resource, but the problem persists.  What is going on?  See attached picture.

  I tried some of these approaches, but they are not what I'm looking for.  It seems that even if the resource does not appear on labview, and I'm still able to talk to her if I manually enter the name of the resource.  The GPIB-USB instruments are those that gave me problems, because I would like to know the address specify the instruments but not their interface IDS. They use different controllers.

  I've written a vi this loop by interface 0-4 with a primary issue specified address id the * IDN? command and check the answer.  With this method, I am able to find the address of the GPIB string and speaks with the same visa instruments does not have this resource.

  I hope that this method will be held up through time.

• When creating Word Document PDF: cannot find the resource Adobe PDF files

  After the upgrade to Acrobat DC, when I try to create a PDF from a Word (any version) document, I get the following error message: could not find resource 'Adobe PDF' files  You want to run the installer in repair mode.

  Even after the execution of repair, still get the same message.  All Adobe programs are installed on the E: drive.  Windows 7 x 64 platform and I am a local administrator.

  Any ideas on how to solve this problem?

  Hello

  Can you please try DC Acrobat uninstall and reinstall?

  Thank you

  Tanvi

• Cannot find the drivers of visa

  Hi all with that I have some visa problems drivers, I have the following error

  LabVIEW: visa (hex 0xBFFF0009E) or a library of code required by visa could not be located or loaded. This is usually due to a required driver is not installed on the system.

  I know that there is a problem with the driver but when I check my windows drivers in the laptop Device Manager it say that the device works very well.

  also I did not receive this message once before and today when I tried to run the sample, this error pops up, I did not change the parameters

  also I m using labview 2009 and my laptop is dell d830 with vista running on it

  regarding

  The windows driver and Device Manager have nothing to do with VISA. Have you tried to reinstall or repair?

• during startup, I get an error message 'Cannot find the resource file' how to restore this file?

  I had a virus fakespypro.  After it has been deleted I can't access my resource file at startup.  I need to reinstall windows vista to restore it?

  Hello

  This message is probably part of the scythe. Is there more information you can give about this?

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Autoruns - free - see what programs are configured to startup automatically when your system boots and you
  opening of session. Autoruns also shows you the full list of registry and file locations where applications can configure auto-
  start the settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• How can I fix an error on start up: can not find the resource file?

  After that a false spypro virus was found and deleted I got the above error message when starting upwards.  How can I fix?

  Hello

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Autoruns - free - see what programs are configured to startup automatically when your system boots and you
  opening of session. Autoruns also shows you the full list of registry and file locations where applications can configure auto-
  start the settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Find the name of the resource of the SMU-4143 NI

  Hello world

  Is there a way to find the resource name assigned by MAX using LabVIEW? I need to use niDCpower initialize wite channels VI to initialize a session with SMU-4143. This VI asks the name of resource assigned by measurement & Automation Explorer (MAX) of the 'PXI1Slot3' form as input. I'm not sure whether we can use VISA find resources to detect the PXI instrument. If so, the resource to find string exit VISA is a different format. How can I get the name of resource affected by MAX of this? Any ideas?

  You can use a constant DAQmx device name or a control.

  Or you can do deactivation:

  

• Can not find the name of resource VISA

  I am trying to run the example code, provided by the manufacturer with a 3a Keithley 2420 SourceMeter.  It is turned on and put in place for 488,1 protocol GPIB.  It is connected to my computer via a GPIB KUSB - 488A cable.  On the front panel of the example program, there is a menu drop down titled "VISA resource name."  The two options at my disposal are LPT1 and COM1, but I don't think one of this is the name of the resource on the right.  Does anyone know what the name of resource VISA should I use with the Keithley, or how I can find this? If it helps, I have provided the example program I use. Thanks in advance!

  As a general rule, only the material NOR will be recognized in MAX and you wouldn't get any VISA resource for Auditors not - NOR. If there is a VISA for the Keithley driver, you can try to install as secondary visa driver and enable Tulip MAX. Keithley support support is the best place to ask questions about the installation of their hardware to LabVIEW.

• VISA: Is denied access to the resource or to the remote machine.

  Hello.

  I use a cRIO-9076 to communicate with a Keithley 2400 via port RS-232 on the cRIO. I have a vi test which is built using the Keithley 2400 drivers and it works perfectly fine with the vi is located under 'My Computer' in my project. If I'm moving that vi on the potion of distance OR cRIO9076 of the project and try to run the vi I get a

  VISA: (Hex 0xBFFF00A8 to the resource or the remote machine access is denied...

  I realized I need to add something to the list of remote access on the cRIO that I find a little confusing. I want to use the serial port on the cRIO by VISA to communicate to the Keithley, so I need to give permission to cRIO on the cRIO? I'm obviously confused.

  I tried to add a simple * (wildcard) to the list of access as a temporary solution but I still get the same error.

  I would like some advice.

  Thank you

  Roth

  cRIO 9076

  Lab View 2013

  Keithley 2400

  NI-VISA 5.4.0

  If you want to move the vi to the CRIO, you can change the name of the resource.

  my example is based on the cRIO-9068. When running at MAX on my local host, it can show as below.

  The resource for the cRIO-9068 should like 'ASRLx:INSTR '.

  

  Good luck!

• VISA (Hex 0xBFFF001E) error the specified state, the attribute is not valid or is not supported as defined by the resource.

  Hello

  First of all that I must say I just starting with control of the instrument using Labview. For this reason, it is possible that the problem I have is easy to solve. However, I am looking for any solution for the forum, but unfortunately I can't fint anything.

  While the situation is this: I'm looking to plug a power Analyzer (Yokogawa WT1800) with the PC through GPIB. To achieve this, I use the USB/GPIB Interface of Agilent 82357 B. The connection is done correctly because I can see and communicate with him through the Explorer NI MAX.

  In order to achieve control of the instrument using Labview, I downloaded and installed the driver of Yokogawa WT1800 (Driver instruments ykt1800) using the NI Instrument Driver Finder tool. The problem I have is that when I run the examples, I find the following error message:

  Error 1073807330 has occurred to the property (arg1) node in Yokogawa WT1800 Series.lvlib: Initialize.vi-> Yokogawa WT1800 series continuous measurement Normal.vi

  Possible reasons:

  VISA: (Hex 0xBFFF001E) the State specified, the attribute is not valid or is not taken in charge as defined by the resource.

  I tried to change the input of the open Visa arguments vi because I think that this is where is the problem, but I can't reach any solution. The following image is attached to the block diagram of the initialize.vi:

  

  Any help is appreciated.

  Thank you.

  I suspect the redirect property. Try to remove it.

• How to detect the resource (find) information?

  Hi all

  I'm trying to detect programmatically information resource name for devices HSDIO PXI and PXI-4130.   How can I do?    System DAQmx property does not include these devices, and I can't find a way to convert a resource VISA name in name of resource HSDIO or NI DC PS formats.  I enclose a code snippet that detects resource VISA for a device 6552 name, but I can't seem to figure out how to get the name of MAX the device resource.   Both the niHsdio and the properties of 'name of the resource' OR DcPS requires that you spend a session valid in them need valid resource name andI to make...

  And no, asking the operator to launch of MAX and find the name of the resource is not an option

  Thank you

  Hello

  Modular instruments and devices devices use their own set of screws to find devices in the system. The lybrary called NOR-ModInst and i's includedin the palette of the utility with the MID drivers.

  Here is a small example that demonstrates the use of their base.

  Let me know there are questions of the amy

  Kind regards

  JC

• After repeated close features, I still get the VISA error "the resource is valid, but the VISA cannot access to this.

  I'm currently building an application on a device cDAQ, which involves the use of a scale. The scale uses the RS232 communication, but is connected to an RS-232 adapter / USB and plugged into one of the USB ports on the cDAQ (COM 10). I am contacting the scale using the basic functions of VISA: VISA Open > VISA Read > clear VISA > VISA family. I created an application using the scale that worked correctly, but now whenever I try to access the scale - whether through MAX, a VI or a version rebuilt in the same application - I get the error "the resource is valid, but VISA can not currently access."

  The scale has three options for data transmission: "No. Data Output" "data output continues" and "Normal output when you press the Print button. I have it set to "data output continues, I don't know if this information is useful.

  The c-data acquisition is a NEITHER cDAQ-9138

  I have tried several things to get rid of this error:

  -Restart the cDAQ

  -Functions "Close VISA" running repeatedly on COM Port

  -Completely unplugged and powered off the coast of the scale

  -Connect the scale on a different COM Port

  -Repeatedly in the course of execution 'unblock port' VISA functions on COM Port, as a colleague has suggested that perhaps the problem

  None of them have worked.

  Does anyone have any suggestions of reliably, get rid of this error?

  I have attached a vi showing how I try to read from the device. Any help would be appreciated.

  A colleague of the Department of electrical engineering of the company has solved the problem. The scale has a material defect that will constantly try to communicate with a VISA session, even if the session is closed for a long time on the computer. Essentially, the VISA session on the scale does not, stop even if she ends up on the computer. He says it's a mistake he has not seen in 3-4 years.

  How to fix the error is to unplug everything from the balance and leave it unplugged for at least 30 seconds to make sure that all of his equipment off completely. When you plug the scale, it will be sensitive to a new VISA session. I tried it and the balance works again through VISA.

• VISA: (Hex 0xBFFF001E) the State specified, the attribute is not valid or is not supported as defined by the resource.

  I try to open a com port Seraglio in LabVIEW get this error:

  VISA: (Hex 0xBFFF001E) the State specified, the attribute is not valid or is not supported as defined by the resource.

  It occurs in ISA set up a Serial Port (Instr) .vi and seems to be related to the speed of transmission. If I use anything else than 9600, I get this warning. I need to use 115200. I can open successfully to other com ports at 115200.

  I am able to talk to this device using other Terminal programs to 115200 without problem. It is only through LabVIEW and NI MAX.

  The Unit presents itself as "Stellaris Virtual Serial Port (COM12)" in deveice Manager.

  Is there a way to get around this?

  Thanks in advance!

  
  

• With the help of VISA can not find the com port

  I use visa read but cannot find any com port in Windows 7.

  How can I find the com port in Windows 7?

  Windows 7 is not released. A version of LabVIEW for windows 7 is not released. A version of NI-VISA for windows 7 is not released. Wait until MS releases windows 7. Then wait tile view deleted OR made available versions of LabVIEW and NI-VISA that work with windows 7.