Firewire OHCI IEEE 1394 controller does not start

Similar Questions

• Win7 SP1 - "Standard Enhanced PCI to USB Host Controller" does not start now

  After I installed Win7 ultimate SP1 fine, I've now that in the Device Manager for the "Standard Enhanced PCI to USB Host Controller" device: Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might be installed a file that is signed incorrectly or damaged, or maybe it's a malicious software from an unknown source. (Code 52)

  Has found the solution on another site.

  In Device Manager, click the Standard PCI enhanced USB host controller that shows an error, just was two more separate the two display errors on mine, choose to uninstall, both. Then click Action - Scan for hardware changes at the top, Windows reinstalls them both and has done so well here for both.

• I have a Pavilion p7 - 1067c and need to install an IEEE 1394 controller, but there is no PCI slot.

  I need an IEEE 1394 port for capture video from my camcorder.  It doesn't seem to be the standard white connector on the motherboard to install a card.  There are a couple of black connectors line up with the empty card slot but not the white connector found on other computers.  I am familiar with the Texas Instruments OHCI IEEE 1394 Host Controller PCI compiant.  Is there something different for this HP?  I would be grateful for any help you can give me on this.

  Hello

  Short black expansion slots are PCI Express x 1 ports so that you will need a firewire card with this type of connection - an example of this can be seen here.

  Kind regards

  DP - K

• Does not start after the upgrade to 1.5.

  Does not start after the upgrade to 1.5.  "EdgeAnimate.exe - not found entry Point? -Point procedure entry GetGestureInfo is not found in USER32.dll dynamic link library. »

  All ideas

  No problems in the past with edge since September 2012.

  =============

  Laptop HP Pavilion dv7-2185dx

  Dv7-2185dx product name

  #ABA product number NV023UA

  Microprocessor 2.00 Ghz Intel Centrino 2 Processor Intel Core 2 Quad Q9000 processor technology

  The microprocessor Cache L2 6 MB Cache memory

  6144 MB of memory

  Memory Max 8192MB

  Graphic ATI Mobility Radeon HD 4650 (M96)

  Video memory up to 2815 MB (1024 MB dedicated)

  500 GB (5400 RPM) hard drive

  Multimedia drive LightScribe SuperMulti 8 X DVD±R/RW with Support Double layer

  17.3 "diagonal HD + LED display high-definition HP BrightView Widescreen Display (1600 x 900)

  Fax/Modem high speed 56 k modem

  Network integrated 10/100/1000 Gigabit Ethernet LAN adapter

  Wireless Connectivity Intel WiFi Link 5100AGN

  The Altec Lansing SRS Premium Sound technology with subwoofer

  101 keyboard compatible with the keyboard keys full size numeric keypad with integrated

  Pointing device touch pad with On / Off button and dedicated vertical scroll up/down pad

  PC Card Slots 1 Slot ExpressCard/54 (also supports ExpressCard/34)

  External ports

  5-in-1 Integrated Digital Media Reader for cards Secure Digital, MultiMedia Card, Memory Stick, Memory Stick Pro, or xD Picture Card

  4 universal Serial Bus (USB) 2.0, 4th port shared with eSATA

  2 headphone

  1 microphone input

  HDMI

  1 VGA (15-pin)

  eSATA + USB 2.0

  1 RJ-11 (modem)

  1 RJ - 45 (LAN)

  expansion port for computer 1 cell 3

  1 IEEE 1394

  irewire (4 pin)

  1 consumer IR (remote receiver)

  Other devices HP Webcam with integrated digital microphone

  Dimensions 16.2 "(W) x 10.9" (D) x 1.37 "(min H) / 1.70" (maximum H)

  Weight lbs 7,74

  Housing for Kensington MicroSaver Security lock

  Turn on the password

  Accepts 3rd party locking safety devices

  Software

  Operating system:

  Genuine Windows Vista Home Premium 64-bit with Service Pack 1

  
  

  Hi, people.

  I was able to reproduce the problem here, so the good news is that you're not imagining things.  We are looking in the options right now for you guys, and I will contact you individually by private message to start again at the top.  This being said, please note that our techniques, Vista is an operating system that is not supported, and our team is not stable time on this platform.  We will do the best we can and we will keep you guys, update as to what status is.

  Thank you

  -Elaine

• MacBook Pro does not start

  I have tried several things but the laptop won't start do not. Power cable showing green light as if the laptop is fully charged. It's like the death does not start.

  Try resetting the SMC

  Reset the management system (SCM) controller on your Mac - Apple Support

  You said "It's like death does not start."

  Does this mean that he shows no signs of life? Indicator light power?

  Hear the carillon?

  Hear the fans?

• MacBook Pro-life extendable start-up chime, but does not start

  I have a start 2011 15 "MBPro8, 2

  Quad Core Intel Core i7

  2.30 GHz

  Boot ROM version: MBP81.88Z.0047.B2A.1506082204

  Intel HD Graphics 3000 VRAM:512 MB

  AMD Radeon HD 6750M VRAM:1 GB

  8 GB of RAM 1333 MHz DIMM0

  It will not start.  Trying to start the machine, it enters a loop-

  1. startup chime

  2. grey screen with Apple

  3. the small wheel starts to turn under the Apple

  4. the screen goes black

  ... and the cycle starts over.

  The computer does not start in Mode safe.  In an attempt to safe mode the loop above has the addition:

  3. a progress bar is displayed but does not progress.

  I have reset the PRAM

  It will start up in target Mode, so I was able to recover data

  In target Mode, I was able to run first aid utility on the drive.  This has not fixed the problem.

  I can hold down the Option key and see Macintosh HD and the recovery Partition.  If I try to boot from the recovery partition, I get the same loop.

  I can start in the Test of online material, which revealed no material problems

  I can boot in Verbose mode and it always happens in the same place

  Execution fsck_hfs (version 226.1.1 of hfs)

  BootCacheControl: cannot open /var/db/BootCache.playlist: 2 no such file or directory

  ' ' It would be possible for me to insert the "var/db/BootCache.playlist" file using target disk mode?

  Other thoughts?

  Have you tried resetting the SMC?

  Reset the management system (SCM) controller on your Mac - Apple Support

• SSD external via USB does not start by default

  Hello Apple community.

  I have a problem with my new external SSD. Given that the base model Mac Mini end of 2014 comes with a disk HARD 5400 RPM drive, I wanted to go to an SSD without having to tear the whole unit. I wanted to exhaust the option 'boot from USB' and I'm having a strange problem. I cloned my Mac to the new drive SSD and slapped in a box set of the speaker. I connected via USB and changed my 'startup disk' to use the external SSD drive. However, it does not start on this unit automatically. When I reboot and discovers the "boot manager" I see the USB being initialized automatically. After disconnection / re - plug the drive in, it appears as a boot option. Once it is initialized, everything works fine and I can boot into El Capitan without any problem using the SSD.

  I am trying to find a way that I can get the Mac to initialize the SSD to the boot upward and choose default. I don't want to have to re - connect the drive whenever I want to start on the SSD drive... Any help and suggestions are greatly appreciated!

  My equipment

  ===========================

  Model Base of Mac Mini (end of 2014)

  1.4 GHz Intel Core i5

  4 GB of DDR3 1600 Mhz

  OS X - El Capitan v 10.11.3

  240 GB SanDisk SSD more - connected via USB3.0

  What unit do you use for the SSD?

  Can you provide a link?

  If the SSD is delivered with a box to provide a link to that,

  How do clone you for the SSD? What app did you use?

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  -If it is repairable, reinstall the OSX. Nothing shall be lost

  How to reinstall OS X on your Mac - Apple Support

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• My laptop does not start

  When my power supply laptop (Presario CQ40 AMD Turionx2) on, it cannot start with a black screen and no response to all keys. The lights indicating Caplock and Numlock Flash four times. I appreciate if someone here can advice me a clue?

  Siowlian wrote:
  

  When my power supply laptop (Presario CQ40 AMD Turionx2) on, it cannot start with a black screen and no response to all keys. The lights indicating Caplock and Numlock Flash four times. I appreciate if someone here can advice me a clue?

  Hello

  Let me help you SLEEP that...

  Here's something first, read about this document:

  Computer does not start and the lights blink or the computer will beep

  Follow each steps quickly.

  I suspect graphics controller does not work.

  Hope this helps,

  Thank you

  * "ACCEPT MY SOLUTION" to HELP others THE PROBLEM SIMILAR & CLICK KUDOS TO APPRECIATE MY ANSWER *.

• HP Compaq DC7800 does not start properly (fan is going crazy)

  Yesterday I wanted to add a TV tuner card to my DC7800, but after that, I saw that the power of the tuner (no PCI) card had disappeared. I decided to shut down the computer and run it. I would work out the power cable later.

  Since then, the computer does not start really. Looks like it starts and the fan starts to turn. After some time, the fan goes completely wild! There is no beeps of the main card. So, it seems that BIOS does not either.

  Please help me!

  Next: is it possible to get the answers here notificiations email?

  My apologies for not responding earlier!

  I have fixed the problem. I removed the firewire card and then started the pc. After that I insterted the card firewire again and both times the computer still worked.

  Probably what happened is this: I had the tunercard connected to the firewire card, but no power supply again. Most likely the tunercard was draining the energy of the firewire card and this way the power supply of the computer has become a sort of State course...

• Acer 5749 does not start

  Hi all

  My acer 5749 flashed a blue screen while I was loading some film from a blue screen USB files is one of those blue screen of death but he went off so fast that I didn't have time to read. The laptop, then stop.

  I tried to restart and got a black screen with a high massif white slider to the left.

  Looked at the bios and is to recognize the hard drive because there is a model name and the series number but it does not start.

  I don't have the original OS drive to try it.

  I dropped the cell phone a week or so more soon on the floor and asked if its connected to that so pulled out the hard drive and reinstalled it, reset the bios to default and, sometimes, settings that it comes up with a screen saying

  TO ATHEOS PCIE ETHERNET CONTROLLER V2.0.2.7 (02/11/10)

  CHECK THE CONNECTION OF THE CABLE!

  PXE: MOF LEAVING INTEL PXE ROM

  NO BOOT DEVICE INSERT THE BOOT FLOPPY

  and sometimes it's just the black screen with cursor solid/horizontal dash above on the left.

  Is the hard drive that's duff and how do I check the disc before I get a new one or is it something else?

  Bob

  All done and works perfectly now thank you!

  Yes iso worked just above asked me for the windows product key and to check I had to do it by phone at the time, I didn't have no driver so no connection NET but everything seems to work fine now and no exclamation point yellow, thanks for the tips

  Bob

• Inspiron 620-7750 Radeon with 450W power supply installed does not start

  Hello!

  I have looked EVERYWHERE online and on the forum and have seen several posts on this topic and still not found a solution that works.  I have a Dell Inspiron 620

  • I5Intel Processor2nd Gen Core i5-2310 / 2.9 GHz
  • Memory8 GB / 8 GB (max)
  • Windows 7 Home Premium 64 - bit Edition operating mode
  • Optical DriveDVD±RW
  • Graphics technology ProcesseurIntel HD Graphics 2000 dynamic video memory 5.0
  • Integrated graphics controller

  Recently, I buy a Powercolor Radeon 7750 graphics card I have installed the drivers, uninstalled the current Intel Graphics driver from Device Manager and then install the new card.  I of course unplugged the PSU got rid of and left in power has failed to myself and plugged into the PCI-E.  After I tired to turn on but it does not start.  Fans begin to turn, including on the graphics card, but nothing comes up on the monitor and it won't start.  When I unplugged the 7750 card it starts very well?

  At first I thought that it was not powered ridiculously horrible 300w PSU they put so that I have upgraded to an a 450w.  Everything works with the new power supply installed without the card, but as soon as I plug the new map, he continues to not start as before installing the card.  I have searched and tried things for 2 days now and CAN NOT find a solution.  I know that the 620 does not access the menu of the BIOS under settings in advance who does not help (don't know why Dell would never think it was a good idea!) so I can't change anything in there.

  Please, any help would be fantastic!

  Thanks in advance!

  The card is a bad card.  There should be ZERO problems with the supply of the stock 305 w and a 7750.

• Windows 7 x 64 installation DVD does not start on a Dell XPS One 2710

  I apologize in advance for the long post...

  Just got a Dell XPS One 2710.  Lot has happened, but let me clarify the current number as briefly as possible: the machine does not start from the HARD internal disk or the Windows 7 Installer x 64 DVD.  He gets through loading files and then gray progress bar when its colorful animation it blue screens with error CACHE_MANAGER.

  I ran the diagnostic, including tests extended memory tests, and they have not found any error in what either.

  When I was troubleshooting this problem previously, in some sort the motherboard got bricks (I don't know what exactly I did to cause that), but Dell has since replaced.  The first motherboard had BIOS version A09.  It has installed A11.

  I can't find any BIOS settings combination that will allow even the Installer Windows DVD to start with the Blue error screen CACHE_MANAGER.  I tried the UEFI boot modes and legacy, I tried RAID and AHCI.  I tried with and without loading legacy OPROMs.

  What I ultimately do is set the start mode of RAID so that I can use the SSD mSATA as a cache ("Accelerate" in the Intel RST Panel).  But I can not even the installer to start on where I can load drivers RST (assuming it's even necessary).

  Other posts have suggested problems with memory, but I took each of the two DIMMS one at a time and I always had the same problem.

  Should I suspect the hard drive?  When we arrived at the machine, he seemed to be running Windows 8 very well - until we went on the way to the side dark and downgraded to Windows 7.  Then once we started to have errors on updates, things has quickly degenerated from there.  In addition, again, diagnoses don't find any problems.

  Any suggestions on how to get at least this puppy to start?   .. .or what have we done wrong?

  Thanks EJN.  It turns out that there is certainly a hardware problem on this machine.  It was a refurbished Dell making machine and apparently when they renovated the it, they missed the real problem.

  The way I know that it is material, it's that we bought actually 2 of them at the same time.  When I started to suspect the material, I decided to try this process on the other.  He worked like a knife through hot butter.  But I will say that the combination of the BIOS set to boot legacy mode and still start the installation with the option to UEFI DVD in the start menu was not easy to understand at first.  But when I followed the correct steps, everything worked very well.

  For those of you who might try this, here are a few things I learned along the way:

  1. According to EJN, take the time to get/burn a CD to install Windows 7 x 64 that already has SP1 on it.  If you go to preserve the UEFI partitions and the boot hard disk, you must have x 64.  x 86 (32-bit) does not support UEFI.

  2 unzip the RAID drivers to the * root * your USB flash or floppy drive and have it in the machine when you start the installation DVD.  I could be wrong, but it seemed to me that the installer looked for them without having to explicitly say it loads the me.

  3. as said EJN, set your BIOS boot legacy mode but use F12 at startup to bring up the Windows Boot Manager and start the installation in UEFI boot mode DVD.  If you want to implement an SSD as cache for your hard disk, you will need to set the SATA controller in RAID mode.

  4. I had partitions UEFI and was able to leave them intact.  Here's a very brief explanation: http://technet.microsoft.com/en-us/library/dd744301%28v=ws.10%29.aspx your results may vary.

  5 take this one as a possible suggestion that is worth what you pay for it: when I got the USB with RAID drivers at the root before starting the installation DVD, I didn't need to load the drivers explicitly.  As I said, it seems that the installation program has been smart enough to find and load what it takes, but honestly, I don't know.  When I load them explicitly, I got errors saying that the installer could not install on the partition, I had chosen.  Makes me think that I could have loaded both times.  What worked for me was NOT explicitly their cargo.

  6. you MUST be at your PC when Setup has completed copy and unpack the installation files.  Don't forget that you have your BIOS set to start legacy mode.  So when he tries to restart to complete the installation, it will try to start using the table inherited from on your hard disk - who is not here because you did a UEFI installation with partitions for UEFI.  So when Setup restarts the first time, you might as well get into the BIOS here and choose the UEFI boot mode.  If you do not, you will need to grab it whenever it restarts using F12 and manually tell it to boot from your hard drive using the UEFI.

  These steps, you should get installed and running.  But another thing I had to understand that when first, I installed and executed the dashboad Intel RST, there is no acceleration option even if my mSATA SSD was found healthy.  I found that if it is formatted and partitioned, you actually go into Disk Manager and delete the partition before the RST dashboard he sees as available for use as a cache.

  I hope this helps others out of me.  It's a heck of a lot easier when the hardware is not bad!

• Cisco FlexConnect 7510 does not start the backup, stuck on "cisco bootloader stage2 loading" image

  Cisco FlexConnect 7510 does not start in the backup image. Yesterday I downloaded 8.1.102.0 on our master controller and rebooted when evertyhing was complete, the controller has not restarted in 8.1.102.0 it is stuck on the screen that says "cisco bootloader stage2 loading" I have hard reset the box with the power button and tried a couple of times. I looked at the material to break the boot with the 'ESC' key, but is not nothing to me either, even modified keyboards, comes to the white screen cisco F2 for Setup / F12 for the boot etc menu, but I'm not able to use the keyboard to enter this sequence. I have my controller to slave running 8.0.110.0 now that he's turned and took controll when the captain went to restart. For any help or suggestion would be greatly appreciated. Thanks Matt

   "cisco bootloader loading stage2"

  This happens when you connect a computer monitor directly to the WLC.  If you connected in the WLC by using the console port, you should not see this.

• ENE PCI Secure Digital / MMC Card Reader Controller does not

  ENE PCI Secure Digital / MMC Card Reader Controller does not

  I suggest that you go the manufacturer of your computers website and search for drivers chipset update.

  Click Start, type: Device Manager

  Press enter on your keyboard

  Click with the right button on the controller listed in the tree view of the devices

  Click on uninstall

  Restart your computer and let Windows redetect.

• VM does not start after that ESXi was replaced by version 6

  Hi all

  
  

  I ran a scary problem after replacing my VMware ESXi version 5.1 to version 6.

  
  

  My server is an Areca RAID controller which is supported by version 6 default. Yes, after installation (clean installation) 6 ESXi on a key USB internal drive, everthing seem good. It shows my store of data stored on my RAID controller and I can see the content, (see attachment, image of my data store) including my VM file - SBS2011.vmdk.

  
  

  I'm not a highly qualified VM pro, but the hard (about 40GB) file must contain my full Windows environment (Windows 2011 server).

  
  

  Have access to my data store on my RAID controller and access to the original .vmx file, everything seems fine. Make a right click of the .vmx, add to the inventory and I'm ready to go... but... it does not start.

  
  

  It shows a resource error, not this additional information. My feeling is that there is something wrong with the location of the Swap, because it looks like the place to swap is located outside the VM storage location (hard). This is what looks like my .vmx:

  
  

  It is not stored on my hard ' / vmfs/volumes / 512 b 5271-cb39b672-c198-001e676870c7 /! It points to a different location.

  
  

  (File VMX also downloaded with this post)
  

  
  

  No I have two question. What would be the cause of this problem, not able to start the virtual machine?

  
  

  Second question. Perhaps a solution: delete all files in my store of data, except the VM-SBS2011 - flat hard file, create a new virtual machine on my server, using an existing drive (showing my VM-SBS2011 - flat hard), I'll be able to boot my virtual machine? It will create a (work) .vmx file to the cool address? There where no snapshots exist when I close my Windows OS down the last time. I lose all the data? Help, please!

  
  

  Currently, I download the full content (all files) of the database on my local computer as a backup. I hope that my hard file will be sufficient.

  
  

  I'm really grateful for your help!

  
  

  . Encoding = 'UTF-8 '.
  config.version = '8 '.
  virtualHW.version = '8 '.
  pciBridge0.present = 'true '.
  pciBridge4.present = 'true '.
  pciBridge4.virtualDev = "pcieRootPort"
  pciBridge4.functions = '8 '.
  pciBridge5.present = 'true '.
  pciBridge5.virtualDev = "pcieRootPort"
  pciBridge5.functions = '8 '.
  pciBridge6.present = 'true '.
  pciBridge6.virtualDev = "pcieRootPort"
  pciBridge6.functions = '8 '.
  pciBridge7.present = 'true '.
  pciBridge7.virtualDev = "pcieRootPort"
  pciBridge7.functions = '8 '.
  vmci0. Present = 'true '.
  hpet0. Present = 'true '.
  NVRAM = "VM - SBS2011.nvram.
  virtualHW.productCompatibility = "hosted".
  powerType.powerOff = 'soft '.
  powerType.powerOn = "hard."
  powerType.suspend = "hard."
  powerType.reset = 'soft '.
  displayName = "VM-SBS2011.
  extendedConfigFile = "VM - SBS2011.vmxf.
  floppy0. Present = 'true '.
  numvcpus = "4".
  cpuid.coresPerSocket = "4".
  scsi0. Present = 'true '.
  scsi0.sharedBus = 'none '.
  scsi0.virtualDev = "lsisas1068".
  memsize = "12288.
  scsi0:0. Present = 'true '.
  scsi0:0. FileName = "VM - SBS2011.vmdk.
  scsi0:0. DeviceType = "scsi-disk" hard
  IDE1:0. Present = 'true '.
  IDE1:0.clientDevice = 'TRUE '.
  IDE1:0. DeviceType = "atapi cdrom.
  IDE1:0.startConnected = 'TRUE '.
  floppy0.startConnected = "false".
  floppy0. FileName = "".
  floppy0.clientDevice = 'true '.
  ethernet0. Present = 'true '.
  ethernet0.virtualDev = "e1000e.
  ethernet0.networkName = 'network of the VM.
  ethernet0. AddressType = 'generated '.
  chipset.onlineStandby = "false".
  disc. EnableUUID = 'true '.
  guestOS = "windows8srv-64.
  UUID. Location = "56 4 d fe 63 9 b 1 has c6 - ba b 0, 00 e8 6f 3rd 80 e8 7A.
  UUID. BIOS = "56 4 d fe 63 9 b 1 has c6 - ba b 0, 00 e8 6f 3rd 80 e8 7A.
  VC. UUID = "6th 52 2d 21 82 34 04 - c8 18 19 67 f8 67 c3 a5 4 d.
  Snapshot.action = 'keep '.
  SCHED. CPU.min = '0 '.
  SCHED. CPU. Units = "mhz".
  SCHED. CPU.shares = 'normal '.
  SCHED.mem.min = '0 '.
  SCHED.mem.shares = 'normal '.
  scsi0.pciSlotNumber = "160".
  ethernet0.generatedAddress = "00: 0C: 29: 7 a: e8:80.
  ethernet0.pciSlotNumber = '192 '.
  vmci0.ID = "1048242304".
  vmci0.pciSlotNumber = "32".
  cleanShutdown = 'TRUE '.
  Replay.Supported = "FALSE".
  sched.swap.derivedName = ' / vmfs/volumes/512b5271-cb39b672-c198-001e676870c7/VM-SBS2011-snapshots/VM-SBS2011-6cbed3a5.vswp '.
  Replay.FileName = «»
  scsi0:0. Redo = «»
  pciBridge0.pciSlotNumber = "17".
  pciBridge4.pciSlotNumber = "21".
  pciBridge5.pciSlotNumber = "22".
  pciBridge6.pciSlotNumber = "23".
  pciBridge7.pciSlotNumber = "24".
  scsi0.sasWWID = "50 05 05 63 9 b 1 a 6f c0.
  ethernet0.generatedAddressOffset = '0 '.
  VM. GenID = "5456487432926317901."
  vm.genidX = "901288717606574007".
  hostCPUID.0 = "0000000d756e65476c65746e49656e69".
  hostCPUID.1 = "000206d70020080017bee3ffbfebfbff".
  hostCPUID.80000001 = "0000000000000000000000012c 100800.
  guestCPUID.0 = "0000000d756e65476c65746e49656e69".
  guestCPUID.1 = "000206d700040800969822031fabfbff".
  guestCPUID.80000001 = "00000000000000000000000128100800".
  userCPUID.0 = "0000000d756e65476c65746e49656e69".
  userCPUID.1 = "000206d700200800169822031fabfbff".
  userCPUID.80000001 = "00000000000000000000000128100800".
  evcCompatibilityMode = "FALSE".
  vmotion.checkpointFBSize = "4194304".
  softPowerOff = 'TRUE '.
  tools.syncTime = "FALSE".
  bios.forceSetupOnce = "false".
  IDE1:0. FileName = "".
  bios.bootDelay = "5000".
  snapshot.redoNotWithParent = 'True '.
  unity.wasCapable = "FALSE".
  tools.remindInstall = 'TRUE '.
  workingDir = "/ vmfs/volumes/512b5271-cb39b672-c198-001e676870c7/VM-SBS2011-snapshots".
  fileSearchPath = "/ vmfs/volumes/512b5271-cb39b672-c198-001e676870c7/VM-SBS2011-snapshots;.»
  checkpoint.vmState.readOnly = "FALSE".
  checkpoint.vmState = «»
  scsi0:1.present = 'TRUE '.
  scsi0:1.DeviceType = "scsi-passthru.
  scsi0:1.filename = ' / vmfs/devices/genscsi/naa.5000878000000000 '.
  scsi0:1.allowGuestConnectionControl = "FALSE".
  SCHED.scsi0:0.shares = 'normal '.
  SCHED.scsi0:0.throughputCap = 'off '.
  scsi0:0.mode = "persistent".
  scsi0:2.present = "FALSE".
  sched.swap.hostLocal = "disabled".
  

  I copied the file-VM in VMWare ESXi 5.5 on another data store (more old HP SAS) server en guess what... it's starting! So for now I'm back in business. It seems that there is something wrong with the original server, because my hard file appears to be damaged otherwise it would not start on my old good spare HP server...

  I still wonder what the hell happened after I replaced the internal drive of hypervisor type USB and installed ESXi 6 on a cool USB. I got in the RAID array. Now, even when I start the server of origin with it's original ESXi 5.1 USB (intact), I got the same error when you try to start the virtual machine. Is thinking there's something wrong with the RAID array but I can access the database on the RAID array and (after you move the content to another VM machine) all files are very well run smooth on the other server. Kill me.

  Any ideas?