First impression

Similar Questions

• W540 First Impressions, CPU speed question

  I received my W540 yesterday, and I am still migrating throughout my W520.

  First impressions:

  (1) keyboard - works fine, no light on the hats of the key is not a problem, caps lock appears on the screen

  (2) track Pad - works great after a few adjustments to my taste

  (3) display LCD - pending

  (4) LED function indication - I miss indicators for the HDD, WiFi & Bluetooth Radios

  (5) weight - My W520 weighs 6.2 lbs, W540 weighs 5.6 lb

  Question of the speed of the CPU:

  I ordered the CPU i7-4930MC, which is supposed to work at 3.9 GHz. After changing the settings of the Power System Manager for "TURBO MAXIMUM", the speed of the CPU is always only show 3.20 GHz on system Properies. How to 3.9 GHz?

  Yes, it will not work at 3.9 GHZ at idle - it goes "turbo boost" as high as 3.9 GHZ on a single-threaded workload that requires a lot more speed, but most of the time, it is going to be lower to save on battery power, cooling, etc.

• Satellite C660 - 28 d - first impressions

  I am happy to say that I just bought a toshi C660 28 d.
  It has the Intel i3 core clocked at 2.4 Ghz. Front side bus to 1066 MHz.
  I chose this model because it display 1080 p without glitching video youtube. Now that I have VLC, OpenOffice, Firefox, Gimp, DosBox, Process Explorer and a few other goodies installed, I'm a happy camper. I like same win7 now that I've discovered how to create a system restore point.

  First impessions are very good with the exception of three questions.
  1 / the touchpad with all its multi touch and the ability to scroll was so bad, I gave up and pulled out an old usb mouse out of the attic. Kept the thing "sulking" all the time and would take up to 5 seconds to move.

  Drive USB 2 speeds / diabolically slow. 1 MB/s when the connection through a hub 4 ports USB 2. An acceptable 20 MB/s when connected solo. But here is the best, according to the self supplied from routine Diagnostics there are two internal USB ports on this system, but only one is connected to the outside world. This connection is done via a hub 8 internal ports. It has only two ports can be used. I think it means that there are 40 MB/s of the port bandwidth go to waste here. If someone comes up with a brazing hack to work around the hub 8 ports I'm strongly tempted to embark.

  3 / this n wireless seems to be a bit of a lame duck. When I plugged in, we talked to 45Mbps. tonight we were able to connect to 58Mbps. My box wireless g connected to 56Mbps as it says on the Tin. It is any activity of 2.4 Ghz. Maybe I should try the 5Gig on my Netgear DGND3700 option.

  > 1 / the touchpad with all its multi touch and the ability to scroll was so bad, I gave up and pulled out an old usb mouse out of the attic. Kept the thing "sulking" all the time and would take up to 5 seconds to move.

  Well, the features and additional touchpad options must adjust.
  But this can be controlled and you can check the options of touchpad available in Control Panel-> mouse-> tab advanced-> avancΘs

  > Drive USB 2 speeds / diabolically slow. 1 MB/s when the connection through a hub 4 ports USB 2. An acceptable 20 MB/s when connected solo. But here is the best, according to the self supplied from routine Diagnostics there are two internal USB ports on this system, but only one is connected to the outside world. This connection is done via a hub 8 internal ports. It has only two ports can be used. I think it means that there are 40 MB/s of the port bandwidth go to waste here. If someone comes up with a brazing hack to work around the hub 8 ports I'm strongly tempted to embark.

  Brazing hack? I think that such procedure would undermine the mobo

  > 3 / this n wireless seems to be a bit of a lame duck. When I plugged in, we talked to 45Mbps. tonight we were able to connect to 58Mbps. My box wireless g connected to 56Mbps as it says on the Tin. It is any activity of 2.4 Ghz. Maybe I should try the 5Gig on my Netgear DGND3700 option.

  802.11 N works only on 2.4 Ghz if 802. 11's is not supported by the wireless network adapter.
  Check this box:
  + Can use the 5 GHz on the map of wireless network standard WiFi "n" +.
  http://APS2.toshiba-tro.de/KB0/TSB0502VM0000R01.htm

  Hope I could help a little, and I wish you fun with your new toy ;)

• In windows 7 my all-in-one Officejet HP6110 constantly gives paper jam paper on first impression.

  After an order of printing the first sheet of paper is taken in two stages, the first step determined fast followed by a slow forward paper at the end of which the flashing light red starts flashing and the screen Announces "clear paper jam and press ENTER. Later print a product normally. This behavior all constantly repeats on each new print command. On my Windows XP pc, the printer behaves without problem. I think it's to do with the operating system. Any ideas how to correct this anomaly will be welcomed.

  Hello
  
  This article should cover the problem you are experiencing. Give the steps described a shot and tell us if it helps.
  
  Good luck!

• The first impression is always be empty on J110a

  The printer only prints the first Virgin each printing paper. I don't know why it is happening and how can I fix this problem. Is the problem with the product or is my problem to use?

  Hi nanie,.

  I understand that whenever you print a document on your HP Deskjet 1000. Have you tried running HP print and Scan Doctor designed by HP to offer users the features and troubleshooting problem needed to solve many common problems experienced with HP print and scan the products related to Windows computers. If you use an old operating system please let me know.

  Do you already have setup for the Deskjet 100 separator page? The separator page is used to separate one document on the other. Generally used when a printer is shared between multiple users, or when there are several documents. A separator page may simply be a blank sheet or custom to include a number of information such as the name of the print job, name of the user who sent the work, etc. so that it makes it easier to find where a print job finished & next starts flipping through printed material.

  Please let me know.

  I would like you to follow the steps below and let me know if in the page field separator, it is empty or if there is a path:

  1. go on devices and printers.

  2. right click on the printer icon and click printer properties.

  3. then click on the advance tab > you will see the tab down Separator Page.

  4. a small window opens with the location of the file. Remove the following path, click ok to save the settings

  I'll watch for your reply.

  Thank you

• A RAW workflow on the iPad - first impressions

  Since Adobe released Lightroom Mobile 2.4, which includes support for editing RAW files, I did experiments with the help of my iPad Pro as part of my photography work that I wanted to find a way to use the iPad as a desktop replacement for when I'm away from home. I wanted to share with you my experience, who has managed for the most part so far.

  The workflow allows me to use my iPad Pro apply enhancements to RAW images (.cr2) taken with my digital camera to edit and share directly from the iPad, or for mounting on Office of Lightroom on PC when I'm at home.

  First of all, for this test the following was used:

  • iPad Pro 9.7 "iOS10 running beta 3, iCloud library active
  • Lightroom 2.4 with subscription cloud creative mobile
  • Lightroom CC 15.6.1 on Windows PC 10.
  • Lightning to (version 2016) SD card reader
  • SanDisk Extreme SDHC I have SD Card
  • account iCloud with 50 GB storage plan
  • Connection of 50 MB fibre broadband

  For the test, I took 216 photos with my Canon G7X in RAW and JPEG mode. Then, I realized that I had to remove JPEG copies like the iPad will read only the JPEG where there is a RAW and JPEG files under the same filename. The workflow is the following:

  1. Insert the SD card in lightning to SD card reader and insert it to the iPad.
  2. The iPad to display the import dialog box and thumbnails of your RAW images will begin to load. Choose select all and Import of Photos (you don't have to wait for the thumbnails to load). It took 2 minutes and 45 seconds to download the RAW 213 files to the iPad, which are about 19 MB each; It is approximately 1.3 seconds per photo. If you are connected to WiFi and have a space of storage iCloud, the original RAW images will begin to be saved on iCloud instantly - you can check it out by going to www.icloud.com.
  3. The Photos app, select Albums > last import > select > select all > Add To > New Album (album name).
  4. With the photos in an album, you can browse and take down the images that you do not want (Note: remove them only sends the recently deleted folder, which permanently deletes the photos after 30 days).
  5. Open Lightroom Mobile. Either import the images into Lightroom, by creating a new Collection: Add of Photos (my preferred method), or by choosing Camera Roll > (drop-down) > Select Album (album to choose or open recently removed).
  6. You will notice a small symbol RAW in the middle of the thumbnails indicating that they are RAW files. Click on... > select all > Add the Photos.
  7. The images will be added to Lightroom Mobile and you can start to make changes on the iPad. Original RAW (no Smart Previews) images are then synced to Lightroom via creative cloud office and will appear in your folders organized as if you imported the directly to the PC. (It is important to note that the original RAW file is now saved on your PC in the same organizational structure of folder you would expect if you were to be imported directly to the office of Lightroom)
  . All changes made to LR Mobile will be synchronized on LR Desktop.
• Once photos are synced to creative cloud severs, you can then remove your iPad Camera Roll to free up storage space (or, if you have enough iCloud of storage, you can free up storage leaving iCloud automatically manages your storage unit so you never run out of space).

Overall, I found the process very simple and the new iPad has more than enough processing power to be able to handle the RAW image editing. It also has a very beautiful high resolution screen. Indeed, during the operation it is much faster than my HP laptop running Windows 10. In addition, unlike the desktop version, LR Mobile uses fully real estate screen on the iPad in edit mode, which makes it easier to use than the complete Lightroom running on smaller laptops.

The main limitation for me is that I still have to make some progress editing such as merging HDR and panorama LR Office, but because LR Mobile syncs across the original RAW images on the cloud, the transition between the mobile and desktop is seamless.

I hope that some people will find this useful. It's great to finally have almost complete office on the iPad's capability, and I think it's really going to transform my photography workflow.

Thanks for this detailed writing. I was curious and wanting to give it a try, but have not had the chance to yet.

• computer crashes with Acrobat first impression of the day

  I have DC of Acrobat Reader.  My system is Windows 7 Home Premium 64-bit.  When I do the first day with Acrobat Reader DC computer print job hangs for a minute then thaws and starts printing.  I have disabled protected mode enabled LPD and LPR in Windows features while disabling Internet printing Client.  None of them have solved the problem.  It seems that there are other people with this problem, but I didn't know all the solutions that work.

  Hi awabel,.

  Please open Acrobat Reader DC, go to the menu help & "Repair Installation".

  Also, try the solutions listed in this KB doc. https://helpx.adobe.com/acrobat/kb/troubleshoot-pdf-printing-acrobat-reader.html.

  Let me know if the problem persists.

  Kind regards

  Nicos

• First impressions

  Yesterday, I received my Xyboard as a replacement for insurance for my Xoom.
  I though that the smallest size, weight more light and the strongest speakers.
  Other than that, it's pretty much like the Xoom, IMO.
  Say-love;
  SD card no.
  No compatibility with previous SIM card for the Xoom (have to go to VZW and get a)

  Asurion claims that my replacement Xyboard is a new unit, however, I guess that's not and here's why.

  My Xyboard did not have a place of the SIM card in accordance with the instructions and will not stop the machine.
  When I press the power button to turn off the device, and you have the charger connected, the unit will ask you if you want to close, I press Ok and the unit turns to the poster who say it stops.
  When he finishes to close, I noticed that the charging light comes on. The next thing that happens is that the unit re starts itself.
  If I remove the power supply and switch off the unit, it will stay off.
  I wonder if this problem is software or related material, either way I am already talking to Asurion to solve the problem.
  I hope that someone here of motorcycle tell me that a software update will fix this if I'm going to be on the lookout for the UPS truck soon.

  A few documents here which is correct.

  Includes:

  When the unit is turned off and the battery charger is inserted, the Tablet turns on automatically.

  Tip: The Tablet is designed to cool while it is powered. When your tablet is powered off and then plugged into the charger, the device will power on. It is a normal behavior. Updates software futures can change that, so don't forget to check the updates periodically.

  Note: load LED lights as a sign of life when the charger is connected to the tablet with 0% battery charge.

• Erroring printers HP DESKJET 5150 on first impression of the map. stackin in the queue behind them.

  I have a HP Deskjet 5150 (old model) with the release of the new driver, but are hot oh here. Could very well be another problem that I "m not certified with network printers

  Hi Robert,.

  Thanks for posting your query on the Microsoft Community.

  According to the description, I understand that you are facing problems with printer.

  I would like to know some information.

  1. What happens when you try to print?

  2. What is the full error message or error code?

  3. Did you change the settings on your computer before this problem?

  Try the methods.

  Method 1:

  I suggest to try the steps mentioned in the article below and check if that helps.

  https://support.Microsoft.com/en-us/mats/printing_problems/en?WA=wsignin1.0

  Method 2:

  Run the printer Troubleshooter:

  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.

• Slow first printing with LBP6000

  I've just implemented a new LBP6000 on my OSX Maverick iiMac running. The first printed page lasts 25 to 30 seconds. In the name of selling on Amazon Cannon wrote several times first impression takes 8 seconds or less. Is it possible I can get 25 to 30 seconds to 8 seconds or less?

  Patrice. Thanks for your help. It turns out that your 3rd point was the culprit. I move to another port and it works fine now.

• Frequent errors in the printer - first part

  1, horizontal black stripes in:

  I use the printer is Canon D 6200. Recently, it has been a fairly deep horizontal black stripes, 3 cm repeated once. Please tell me I can fix it somehow? Thank you.

  Electric Tran Anh: As described, your printer is broken rubber neutralize the charge of the cartridge. You need to replace the neutral printer rubber to function normally again.

  2, not sharp, not "BOLD"

  My new ink printer, not much, the first impression is always good, but lately, I see the word more and more blurred, although I adjust the ink dark on your computer.

  Electric Tran Anh: cannot open word as you describe is very common and a large number of reasons. However, in your case, we would like to respond as follows:

  -First of all, you must clean the reflector system because it is maybe dirty.

  -Can your ink is not good, poor toner powder. Please contact provider level.

  -Excluded since the loss of elasticity and cause dangerous conditions.

  -Case of the tree that is worn, replace the axle.

  3, replace the ink cartridge but still fuzzy

  Why when I print on a laser printer, printing is blurry than usual, despite the ink?

  Electric Tran Anh: Little ink printer saving printing mode (ECONOMY), if you choose this mode, the printer will be lower than normal. You check on the machine, if there is the ECONOMY on the off button.

  Some printers allow the game into saving mode in the driver. You right click on the printer icon and select Print Options, and then select Advand, the EconoMode you select Disable.

  If after the toner save mode is disabled in the printed page still blurred, particularly irregular opacity faded by the optical lens, you must call the service center for the maintenance of the machine to.

  4, on the prints have a black along the mark

  Electric Tran Anh: in this case, your printer may be damaged in one of the following two items:

  -Out of the with the stick of condensed ink, cleaning wipers will be any phenomenon.

  -Excluded amount of recoveries of damaged, should be replaced by the new ink brushed.

  5, fuzzy printers

  My printer after a period of use, the ink smudges on the page seems very happy to know how to fix?

  Electric Tran Anh: Printer blurred the following possible causes:

  1 paper

  -Print: print paper you use problems such as humidity, or too thin.

  2 ink

  -If your cartridge is not the right way, the wrong type causes this phenomenon.

  3 vacuum

  -If you purchased your printer to empty less long.

  4. a lot of drying

  -If your oven is not hot enough can also cause the phenomenon.
  You can check the case to know the why of the difficulty of typographical errors.

  6, printer pull more paper

  My book of standard printer paper, it is not washed once a piece of this book of many pages at the same time always (for the two pad on it) made me know the cause and how to fix it?

  Electric Tran Anh: With this phenomenon, peach paper book you wear, you need to replace the printer works better.

  7, defective printing fonts

  I use the HP LaserJet 6 L printer, Word 2000 printer. While in some fonts VNI fonts are lost or overlap, though not seen this phenomenon in mode print preview, it does not happen in some programs and not any characters, when in when not.

  At that time, I have to change to a different type, but can be the next in this model also fails.

  I tried to reinstall the printer, the word, and the same fonts. Tried with disc of different fonts, this does not happen during the previous installation. Please tell me the cause and how to fix it?

  Electric Tran Anh: You also use the HP LaserJet III (including the HP1100 printers). However, there are easier ways is to open the printer before you start the computer, the mentioned error (if the computer to open again on the finished Word Editor open the printer is down).

  Including former open files before you open the printer (too always) an error only in some HP 5 L and 6 L belonging to the same production batch.

  If you buy previous versions or batch after this error.

  8, photo ink cartridge

  I use the printer / copier Ricoh, why can't ink to Toshiba?

  Electric Tran Anh:

  -On the principle of works, created and covered the same parent ink on paper printers and copiers

  -Squid ink printer or copier in general are: Special powder. The basic structure of the cartridge consists of two components: colorants and substance of viscosity, (as the candles burn).

  In addition, printer copier of ink because it is mixed with the powder of.

  -Due to the structure of these special inks so that each type of printer, copier must use ink in connection with merger powder can help the machine works well. Therefore, the machines of different manufacturers rarely shared with each level.

  Welcome to: may in canon . Can in hp | MUC in canon . MUC in hp

  Hi Joomny,

  You will need to contact Canon for issues with your Canon printer. Here is a link to the support Web site.

  Support for Canon

• 4K Canon EOS5D Mark iv and EOS1DX Mark II video

  Hello

  I can't play or correctly modify videos 4K of the EOS - 1DX Mark ii on my Mac. The images are wiped out as if it were 5 fps.

  I have OS X El Capitan 10.11.6 with 2.6 Ghz processor Intel Core i5, 16 GB of RAM, Intel Iris 1536 MB graphics card.

  I usually play and edit 4 K Panasonic video with no problems.

  Here, I tried the Canon 4 K MJPEG with Final Cut Pro X, Quicktime, VLC, video player Rocket and EOS Utility film without success.

  The EOS - 1DX Mark ii as well as the EOS - 5 d Mark iv btw are not on cameras for Final Cut Pro X.

  https://support.Apple.com/en-us/HT204203

  I also tried to play videos 4K 1DX - EOS Mark II on 5 different Mac and it has always failed. I tried on a Windows PC, and it worked.

  Apple support told me that Canon codec is missing to play videos 4 K 1DX - EOS Mark II.

  Can you confirm?

  What can I do without losing the quality 4K

  You can search this forum for the camera model, but I think that you will get a faster response by visiting the Canon support forums, if they exist. If there is no available for Quicktime codec, you go through a conversion software, upstream of FCPX. The camera came with a way to move the motionjpg files to a Macintosh? Should have.

  http://nofilmschool.com/2016/05/field-review-Canon-EOS-1d-x-Mark-II

  https://www.YouTube.com/watch?v=p67plTeMyD8

  http://newatlas.com/Canon-1DX-MarkII-DSLR-4k/41619/

  https://www.cinema5D.com/Canon-EOS-1d-x-Mark-II-review-real-world-video-samples-: first-impressions.

  http://www.newsshooter.com/2016/06/18/the-Canon-1DX-MKII-4k-video-DSLR-reviewed-par-Jon-Roemer /.

  The X II 1 d produces very nice video 4 K, but there's a catch: capture 4 K is limited to Motion JPEG. Motion JPEG is a relatively inefficient compression method, especially compared to the codecs of H.264 - based, such as Canon XF - STROKE (which is still on the compact Canon XC10). It requires broadband which produce large files. As you can see in the table below, 4 K/30 p of record runs nearly 500 Mbps and 4 K/60 p manages nearly 800 Mbps. By comparison, Sony a7S II captures 4 K/p 30 to 50-100 Mbps and the Panasonic GH4 is 100-200 Mbit/s.

  But what about the 4 K?

  The biggest upgrade in spec video camera is the addition of 4K film but, curiously, this can only be captured by using Motion JPEG format and the greater-than-16:9 DCI 4 K (4096 x 2160 pixel) aspect ratio. Two of these choices seem odd: all - I have H.264 compression, the camera uses to its 1080 images would be a more effective choice of codec and UHD 4K 16:9 flavor is better suited to certain applications.

  However, with the capture of 4 K, the 1 d X II includes tools to capture 8.8MP frameworks of its 4 K files: how the decision to save each image as an individual JPEG is a bit more logical. Wedding shooters could even use this feature for document receptions in complete silence: despite the 1 D X II wins a continuous silent drive like the 5 d/R mode, it isn't all that silent.

  The 1 d X II also won a headphone jack, which is important for the monitoring of noise levels during video recording.

• Replaced the cable. Now, the screen does not work. What could be?

  The cable coming out of the back of my monitor Apple Thunderbolt Display is fraying. I decided that rather than risk a short at a certain point, I preemptively replace the cable. On iFixit teardown photos, I decided to replace the cable coming out of the back of the screen myself instead of paying almost $200 to get an Apple service provider to do that here in Bangkok. Bought the cable on AliExpress for $12. It replaced. And... no dice. Screen has not come.

  My setup

  [MacBook Air]-[Thunderbolt Display]-[drive Thunderbolt]-[Cinema Display]

  with a key USB drive and Ethernet connected to the back of the Thunderbolt display

  Already tried this

  • First impressions were that the cable was defective. But then I noticed Ethernet came the USB has been mounted, Thunderbolt was mounted drive and after a reboot, the movie screen come also. Obviously, the cable has been working very well.
  • Second thought was that I'd neglected to plug some cables that connect the LCD to the main logic board. I checked. Seemed fine.
  • Third was maybe the serial number of the cable was somehow connected to the main logic board. So I put the old cable. Still no screen.
  • Tried to connect the screen with a Thunderbolt external cable, everything worked as well but still no image on the screen.
  • Tried more than 30 seconds and 3 hours disconnected as a "reset" of the screen. No change.
  • Restarted my laptop. No change.
  • Thunderbolt Display well plugged the drive and then into the MacBook, so change the sequence of the devices. No change.
  • Information reports under "Thunderbolt" the entire chain of devices, but under "Graphics/displays" system displays only the internal screen and Cinema Display.
  • Using the newly purchased cable as a Thunderbolt external cable works fine too.

  Question

  Does anyone have suggestions on what to try next?

  The logic card goes into a sort of locked mode when you replace the cable?

  Is there more than 3 flat cables connection + connection to the land between the Panel and main Board?

  Although there is no reason to think that this has been, how to test LCD screen still work given all these flat cable connectors?

  
  

  Note: There is no Apple here store.  Apple authorized service providers are without help. He suggested to replace the cable and the Panel at a cost that is almost the same as the purchase of a new screen.

  Some of the cables that connect the LCD to the main logic board, are very short. Careful lifting the LCD, because it will go away with strength cables once that raise you it more than 2 to 3 inches on the side of the camera module.

  The shorter cable of all is the LVDS cable. A short cable with gold plated connector. Although I have had reconnected the cable on the side of the logic board, I had wrongly assumed that the other end of the cable was stayed connected because all the band used on. Someone with experience of fixing these things said of his town for this cable to unravel by force and to be sure to check both ends of the cable. When I peeled back the tape, I found that he had indeed been disconnected. Reconnect, fiddling with the tiny workspace to get the logical side of Board of Directors of what properly fixed cable again and we were back in business.

  Apple authorized service providers here in Bangkok have quoted me $200 to replace the cable. I ordered the replacement cable Thunderbolt Display off AliExpress for $12.50. It was really simple to replace the cable, just to keep an eye on this darn LVDS cable opening to the top of the screen!

• Install repeat me it was inturrupted.

  I have Windows 8 on a fairly new computer. I have installed many things without any problem. Try to install Firefox so that I can use FireFTP. A friend told me that it works very well. However, at the end of each installation (which takes a while), I get an error that says that my installation was interrupted. When I click on "ok" a window opens that pushes me to use the other installer of mozilla. At the end it says the installation is complete, HOWEVER, the icon on my desktop is a file looking for empty exe and when I click it, it wants me to find the exe file for which there is no. so ya... not the best first impression for me with firefox.

  Any help is appreciated.

  Also, I check any malware or virus that I have none. Won't install not disabled my firewall, protection against viruses and malware protection and it still.

  Try to delete the program directory and install again.

  If this is not successful, remove the program directories. Then download and install an older version of Firefox from here.

  If you install an earlier version of Firefox has worked, please update as SOON AS YOU OPEN THE BROWSERFirefox.

  The report please come back shortly.

  WARNING: Removal of the files/folders could damage other programs and the Windows operating system. Be careful when you manually delete the folders/files.

  WARNING: Always be careful when downloading content on the internet. I will take no responsibility for any damage caused by a download. Download at your own risk!

• Portege Z830-10N Windows 10

  Hello

  I see it on the table to display Toshiba Portege Z830-10N is not able to be upgraded to Windows 10 why is - this? The laptop is not that old, and the system is quite high spec as far as I know. I tried yesterday and it has been initialized to offshore, but without any reason. Can someone let me know why?

  I thank... Paul

  Have Z830.

  Recently upgraded to Win10 after invitation to Microsoft to improve the system. The process was smooth, but in the end got 5 unknown devices in the system, including Web camera. So goodbye video Skype.
  More functional keys work but only OSD system (windows) are displayed - don't know how power 3D modem for example.

  First impression of Win10 - no real advantage compared to Win7.
  If not find a solution for my problems in 1-2 months - will return to the registered system.

  Someone managed with 10 windows on Z830?

  Good luck
  AK