[FlexRIO] Is it possible to define two modules e/s for my FlexRIO

Hi all

I developed an application to perform a test on a digital ASIC business and have a number of PXI chassis each with an installed FlexRIO. I have two flavors of DIO FAM the NI6581 & the OID NI6583. I want to write the code LV FPGA so that the application can use either FAM that it is mounted on the FlexRIO. Is it possible to set both FAMS IO in the LV FPGA project and the code detect what FAM is mounted and from there select the e/s to use?

Thank you

Nick

Nick,

While you could not define 2 FAMs under a single FPGA target in the project, you can do the following:

1. create two targets FPGA, one for each Module IO

2. write two screws FPGA separate, one for each Module IO

3 compile the two bitfiles

4. write a VI host that uses the host FlexRIO screw interface to check which adaptor module is attached.

5. deploy the appropriate bitfile depending on which adapter module is attached.

Keep in mind, we do not recommend the adaptation modules FlexRIO hot spare so that you wish to power your system every time you had to adapt modules.

I hope this helps!

Tags: NI Hardware

Similar Questions

  • Is it possible to merge two distinct creative cloud for accounts of the teams?

    We have recently been acquired by another company, and we each have our own creative cloud to the team accounts. Is it possible to merge two distinct creative cloud for teams accounts into a single account? Or we will have to cancel our account and recreate all the users on the new account.

    Hello

    You will need the account teams cancel and Add license that you want to keep and assign members.

    Kind regards

    Sheena

  • Possible to define strategies of OAM configuration on the same site on two different

    Is it possible to define strategies of OAM configuration on the same site on two different servers?

    One of the sites to have anonymous access but it to be protected. How to set up a policy without it automatically applies to all Web sites that match regardless of the host.

    How to differentiate the two OAM sites so that I can apply security different strategies for each of them?

    Thank you.

    You can refer to this [recent thread | http://forums.oracle.com/forums/thread.jspa?threadID=878094&tstart=0].

    Also, if one of the sites requires anonymous access for all the content and it's not going to change in the foreseeable future, just don't install/activate webgate on that.

    -Vinod

  • HP EliteBook 8570w: is it possible to run two monitors on a 8570w without a docking station.

    Is it possible to run two monitors on a 8570w without a docking station. Connect a monitor to the VGA port and the other to display port.

    I was able to get this to work. My 8570w has an Amd over-pants 7700, don't know if that matters. One is connected VGA other Displayport. The port monitor must have a custom resolution defined in the over-pants Control Panel. except that it works perfectly. More laptop screen no. Docking Station 2 24 inch Dell.

    And thanks for the quick reply Provost.

  • is it possible to use two external LDAP and authentication of external Table?

    Hi, is it possible to use both external LDAP and authentication of the external table?

    they all need two initialization blocks to access a session system variable, USER?

    Thank you

    Hello
    I don't think it's possible to impliment the LDAP authentication both extenal together. The reasons are,
    1. we cannot define two sources (LDAP and Extenal DB) in the same blocks of justine initialization user information.
    2. If two different (one for LDAP) initialization blocks and one for extenal DB are used, we cannot use variable USER twice it's a defined system variable.

    Thank you
    Swami

  • Is it possible to make the modules to activate as needed rather than turn to the browser start or disabled?

    Extensions and Plug-ins have a disable or remove the button, not a sleep button. Is it possible to put these to use when the application needs instead of either on or off? It seems that Firefox starts with them all turned on, my browser startup time increases considerably. I don't need to plugin Quick Time or Windows Presentation Foundation to start the browser, but perhaps need them during the session, according to request.,.

    Start Firefox in Safe Mode to check if one of the extensions (Firefox/Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/Firefox/tools > Modules > appearance).

    • Do NOT click on the reset button on the startup window Mode without failure.

    It is possible that your security (firewall, antivirus) software blocks or limit Firefox or the process of plugin-container without you inform, possibly after the detection of changes (update) for the Firefox program.

    Delete all rules for Firefox and the plugin-container in the permissions list in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container and the update process.

    See:

  • Satellite L850 - is possible to connect two monitors external simultaneosly

    Hi, I have a L850-150 and I would like to know if it is possible to connect two monitors external simultaneosly, one by Hdmi and the second by Vga to enjoy an installation of three active screens (including the laptop screen). Im trying to figure out how to do without using a USB to adapter vfga or a Matrox dualhead2go.

    I want to use the outputs existing.
    Thanks in advance

    Some laptops supports a dual output: for example the Qosmio X 500 as shown here:
    http://APS2.toshiba-tro.de/KB0/TSB13033Y0000R01.htm

    But for Satellite L850 this isn t possible.
    But you can use an external device, such as Dynadock
    http://www.Toshiba.com/us/ACC-dynadock

  • Is it possible to have two Skype accounts on a Windows 7 computer?

    Is it possible to have two Skype accounts on a Windows 7 computer?

    Yes.

    https://support.Skype.com/en/FAQ/FA829/how-can-i-run-multiple-Skype-accounts-at-the-same-time

  • Tecra M5: Is it possible to connect two monitors?

    Hello

    Is it possible to connect two monitors the Tecra M5? Is it possible through the port replicator, perhaps by a split of dvi output or a dvi, one on the vga monitor. I want to divide between the two monitors.

    At soon now
    Iain.

    Hello

    No, it's not possible to connect two external monitors.
    If you want to split the screen, you can use the extended desktop option.
    In display properties, you will find the option to extend my desktop on this monitor. You must select the second monitor and activate this option.

  • Is it possible to define the image poster in browser FCPX?

    Is it possible to define the poster frame of the browser FCPX to the last frame of the clip?

    My use case:

    I have bunches of clips on a SD card, good and bad, taken from several scenes. Clusters.

    Each bad take is cut while now a red card to the camera. So if I had some way of looking at the last picture of the clips, I would not put the clip in the timeline or skim even the clip had been sloppy and should be rejected. I have confirmed with Canon that our XA25 will only display the first image of the scene. FCPX seems to like to display the middlemost image like the poster. If it is can not editable in FCPX someone Adviser of another method?

    Thank you!

    You can post a screenshot of the place where in FCP you are talking about? The browser may display several images and view film, you can zoom in the film of the clip. There is no single framework for the poster frame.

  • Is it possible to disable selective module TestStand cards?

    Is it possible to selectively disable adapters module of TestStand? For example, to configure the TestStand development environment to only have the LabView module adapter available for developers.

    Husni h wrote:

    Thanks for the reply. Is the permission to change the cards under the privilege of config adapter? How can we TestStand be installed when the user accounts are for example pre-configures administrator account by default with a different password than white and the default developer with the off adapter config privilege privilege?

    You can install the custom file users.ini if you wish after you are done editing. It is located in the directory cfg teststand.

    Hope this helps,

    -Doug

  • Is it possible to define the name of the path and inside the MSI log file

    Is it possible to define the name of the path and inside the MSI log file, so that it should not be set from the command line.  This way just race the msi causes always a logfile in a specific path and the file name?

    Read the following article and see if it helps.  In my view, it is possible to use InstallShield, but I'm not sure.  It's just a little out of my League. http://www.flexerasoftware.com/webdocuments/PDF/msi_writing_to_the_log_file.pdf.

    I hope this helps.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • Is it possible to have two routers on the cable line (T1?)?

    Question?

    is it possible to have two routers on the cable line (T1?)? First router was provided by the cable operator and runs @ standard speed(802.11?), while the router I want to add is a netgear product that will perform @ 2.4 GHz and 5 GHz. is it possible to do this without interfere or affect with speed of cable of the router?

    Thank you

    Rooster

    Question?

    is it possible to have two routers on the cable line (T1?)? First router was provided by the cable operator and runs @ standard speed(802.11?), while the router I want to add is a netgear product that will perform @ 2.4 GHz and 5 GHz. is it possible to do this without interfere or affect with speed of cable of the router?

    Thank you

    Rooster

    What is the router of society provided separate cable from your cable modem? If so then why not just use the Netgear router instead of the provided ISP router?

    If it is a combination cable modem/router device and you want to run the Netgear router as a wireless access point then only...

    Here is a FAQ that will help you in this...

    http://www.dslreports.com/FAQ/11233

    Basically would be configured with a LAN IP in the same range as the IP address you get from the existing cable modem/router Netgear, Netgear is connected directly on the LAN cable port existing via a LAN port modem/router, Netgear DHCP server is disabled and that you configure the single wireless SSID, type of encryption (that is to say.) WPA2 is the best and do not use WEP) and a strong key. Here is an example...

    http://sdrv.Ms/LrESP6

    When you configure the Netgear I recommend that you connect to it with an Ethernet cable if you screw up the wireless and the DHCP part you can find and recover.

  • Is it possible to export the modules TMSPE?

    Is it possible to export the modules TMSPE?

    We have hundreds of users manual that had been migrated for the provision of the legacy and are now running on TMSPE.

    Now, we must export the user information to fill a spreadsheet to download a new UC Jabber (CUCM) environment.

    Any ideas?

    PS: This client have no AD/LDAP. All modules are stored in TMSPE DB.

    Thank you.

    I am not a SQL admin so I can't tell how to export the data, but you can get this information from the tmspe database in the dbo.ur_user table.  Passwords will be hashed, exporting are so useless.

    Columns of the table in the dbo.ur_user that will be relevant to what you want are:

    • username
    • E-mail
    • first name
    • last_name
    • title
    • company
    • Department
    • office_phone
    • Mobile_phone

  • Is it possible to cascade two systems of Community trade marks?

    Hi have the following installed:

    * Manager CTS

    * CUCM

    * 1 x CTMS in South Africa

    * 1 x CTMS in Ghana

    Is it possible to cascade two systems of Community trade marks so that all devices in Ghana connects to the a Community trade mark and all appliances in South Africa to join the South African CTMS and then connect the two systems of Community trade marks between them?

    Hello.

    Yes it is possible,

    Please take a look at this link

    http://www.Cisco.com/en/us/docs/Telepresence/multipoint_switch/1_9/design/guide/nwmp_preface.html

    Marius

Maybe you are looking for