For the Cisco router memory usage
Hello
We have a router SA520 (Firmware 2.1.18)
We use only this for about 1 month now. Router seems ok it's just
I am concerned about the use of memory who reach 62% (144/234 MB)
What's to worry?
How can I use that by cutting down the use?
Excuse me, I'm just for new Cisco devices.
Thank you very much.
CA
AC,
Please go ahead and upgrade to the latest firmware 2.1.51 memory use should not be a problem. After the upgrade, please keep an eye on the back of the memory and the report.
Thank you
Jasbryan
Support Cisco engineer
.:|:.:|:.
Tags: Cisco Support
Similar Questions
-
Shoot of disorder for the Cisco router
Hello
I want to know how many times router restarted what command I need to use
I want to know how many times router restarted what command I need to use
After the complete output of the command 'sh version.
-
Hi Expert,
How to distinguish the physical interface and logic (subinterface) interface to the Cisco router/Switch? Can you please clarify a formal way for this so have?
A physical interface is numbered with the same name of the interface when printing on the physical port. For example "GigabitEthernet 0/1" corresponds to port 1 of the 0 module (or the base unit).
A logical interface can be a subinterface on a routed port and will have a point ("". "") preceding the number sous-interface (ex. GigabitEthernet 0/1.1). It can also be a loop or a virtual interface (on a router this could also include interfaces like the tunnel and virtual tunnel or VTI types). A switch may also have a VLAN logical interfaces (e.g. interface vlan 1) which are used as layer 3 virtual interfaces of type.
-
How to create a VPN file .pcf for the CISCO VPN CLIENT software profile
Dear all
How to create a VPN file .pcf for the CISCO VPN CLIENT software profile
Concerning
Hi Imran,
Can't do much about that because it depends on what authenticate you the VPN server and how the settings. But let me introduce you to the memory layout. Once you install and open a VPN client. Press it again and it opens up a new page for the VPN config.
Example of configuration as it is attached. But it differs depending on the configuration of your vpn server.
Once you create and save this profile. Your FCP file is stored.
Please assess whether the information provided is useful.
By
Knockaert
-
Satellite M30X-165 - need a driver for the PCI Flash memory
Hey,.
I need a driver for the PCI Flash memory, I have already searched the web and posted in other Forums, but I can't find anything. I heard he is hidden somewhere in another file... ? !
I have a toshiba sm30X-165I would be very happy if someone can help me!
Kind regards
Freddy
Drivers for Satellite M30X are placed in the archive on the European driver Toshiba page.
Product type choose Archive.
Then the Satellite-> Satellite M-> Satellite M30XThere, you must download and install the Cardbus and Chip Set Utility driver
-
Record of equipment for the Cisco AnyConnect client NAM module
Hi all
Forgive me if this has been asked before or on the Cisco site somewhere (I could just find)
Are there hardware specifications for the Cisco Anyconnect Network Access Manager module?
Where can I find what wifi chipset is compatible with?
Thanks in advance for your answer.
Compatibility with the NAM module is based on the chipset not guest OS. The current operating system compatibility is listed here.
-
Evaluation version for the cisco secure access control server
Hello
I can get the trial version for the cisco secure access control server. IF SO pls send me the link.
Thank you
Hi Thomas,
You can download ACS for windows 4.1 or 4.2 from the link below:
http://www.Cisco.com/cgi-bin/tablebuild.pl/ACS-win-eval
For ACS 5.x, please visit cisco.com
Download software > Security > Cisco Secure Access Control System 5.x > Secure Access Control System Software
HTH
Kind regards
Jousset
Please evaluate the useful messages-
-
How can I pay for the reservation of memory on all virtual machines to "0"?
I am trying to write a script that will pay for the reservation of memory on all virtual machines that are invited in a cluster to '0 '. We have book too much memory, and this setting should allow VMWare facilities manage reserves memory for me. I have hundreds of virtual machines to update, so I can't do it by hand. I hope that it is possible via the CLI.
Can someone help me with this please?
Matt example work certainly, and I'm sure that he was going to follow up with something similar to this after having confirmed if it worked or not because it is much more serious on the optimization of code for speed, but I'll (try to) save the effort. To test its extract on a cluster of 45 VMS, it took more than four minutes to complete. The excerpt below took about 25 seconds. The difference is of course to use the cmdlet "Get-View" and that it can run asynchronously so (it begins a vCenter task and immediately passes the following). Of course, this will also put more of a strain to your vCenter server, so keep that in mind.
$spec = New-Object VMware.Vim.VirtualMachineConfigSpec $spec.memoryAllocation = New-Object VMware.Vim.ResourceAllocationInfo $spec.memoryAllocation.Reservation = 0 Get-Cluster "YOUR_CLUSTER" | Get-VM | Get-View -Property Config.MemoryAllocation | %{$_.ReconfigVM_Task($spec)}
-
I'd like to find the password for my Cisco router
I can't connect to my network wirelessly on my ereader, because I don't know what is the password when asked.
Read the manual for the device (Cisco router) should tell you what the password by default is to manage the router (if this does not work... it should tell you how to configure the default router, so you can use the default password to reconfigure) so you can go and change the password to access wireless to something You know.
-
[Cisco ACS] Memory usage limit
Hello
We have 2 CSACS 1121 with Cisco ACS 5.2.0.26.10
The main server manages authentication 20000 + per day.
Its memory usage is growing every day.
It's now 83%
Is there a limit?
What happens when memory use reaches this limit?
What can we do to purge the memory usage? (reboot, restarting the service...)
Thanks for your help
Patrick
Check the secondary collector newspaper. This will help to balance the load between the two nodes and you will see the memory usage decreases.
Thank you
-
Optimize the creation of table 2D for the use of memory and parallel processing
I have, and application of data processing that requires generating a large matrix 2D with sin and cos values that must be updated constantly. It's my program in terms of speed and memory use and I want to optimize to the maximum the neck of the bottle. This is my current code:
I tried to paralellisme iteration in the loop for to take advantage of the multi-core processor, but with shift registers I can't do. Also, I read that with in place element, structures I can reduce the memory usage, but don't know how to do this with a 2D array. This code can be optimized to improve the use of memory and speed?
-
Security question for the e1000 router
The E1000 router is equipped with a default security setting when installing using the supplied CD?
When you install the E1000 router using the CD, it will create a secure for you wireless network. Also if you install the router successfully using the CD, it will also create a network of comments for you.
The main network will be secured automatically using WPA/WPA2 mixed mode security.
After the installation of your router using Cisco connect, go into settings of the router. You will find the name and the password of your wireless network.
-
Try to add the Cisco router to hyperic - where are the log files?
I have a hyperic server. I have create a new network platform for the snmp information in my cisco router.
I put in the snmplp $ip, the snmpCommunity... and I thought that I was...
Well, I'm not able to collect any settings.
My question is, where are the logs for this?
seems that you need a "connection of the agent" I guess it's to say to use any server running the hyperic on that agent?
Yes, you need to select an Agent to perform the actual analysis of SNMP. The Hyperic server doesn't have the capacity.
On the Agent, you should be able to see the errors in the agent.log
-
Dash for the CPU and memory in the custom user interface
I need a custom dashboard,
where I will get all the vm in widget and when I select a vm on the widget side it should show % CPU, % memory usage or a latency of disk all in one metric graph.
Can someone help me?
Of course, you need to do is to create a resource interaction file, and then assign this file to a Sparkline widget or graphic metric. Interactions will be "selected resources" widget list VM for the reception of graphic style widget. See the information here:
Re: interaction between widget and widget graphic metric detail application
-
The SQL Developer memory usage is very high + session monitor work not
Hello
I'm facing 2 problems with SQL developer tool.
(1) high memory usage (about 160 MB).
(2) when I click on tools-> monitor sessions, session related window opens upward.
I use 1.5.4 version. Please let me know if there are fixes for these issues.
ThanksHello
(1) not much help for you, but for me, 160 MB is not excessive use of memory for SQL Developer (mine is currently sitting at around 150 MB). And then, I have been using the tool for a while and have a lot of memory on my computer.
(2) tools > Sessions of the monitor works fine for me (DB 10.2.0.3). Do you get an error message when it "does not open upward? Which version of DB are you using? If you go through the browser reports (see > reports if it is not already displayed) and select Data Dictionary reports > Database Administration > Sessions > Sessions, does it report?theFurryOne
Maybe you are looking for
-
Why stop to share photos on facebook via iphone ios? Please try to put this service again
Why stop to share photos on facebook via iphone ios? Please try to put this service again
-
A100-158, X 1600 low performance
Hi, I have a Satellite A100-158 with mobility X 1600.When I run 3DMark05, my score is only 2548 when it should be at least of 3600. Several websites tested the X 1600 and they get good scores...I use Toshiba drivers for ATI catalyst 6.3 do not suppor
-
I try to install updates on windows but sp1 fails why
-
USB CODE 10 ERROR, troubleshoot automated, everything is OK, resart problem comes back after a reboot...
-
is it possible to make a lot of layout for phone Adobe Muse in the mobile web browser like safari?or hind the search and address bar.I can't wait to meet you! Thank you[Moved from the Lounge Forum for a specific forum - Mod]