Record of equipment for the Cisco AnyConnect client NAM module

Similar Questions

• How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Dear all

  How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Concerning

  Hi Imran,

  Can't do much about that because it depends on what authenticate you the VPN server and how the settings. But let me introduce you to the memory layout. Once you install and open a VPN client. Press it again and it opens up a new page for the VPN config.

  Example of configuration as it is attached. But it differs depending on the configuration of your vpn server.

  Once you create and save this profile. Your FCP file is stored.

  Please assess whether the information provided is useful.

  By

  Knockaert

• Cisco AnyConnect Client - specify the certificate store in profile

  Hi all

  Running Cisco AnyConnect Client version 2.5.2019 with Cisco ASA 5510 version 8.4 (1)

  I can't get the work certificate (see attached picture) store profile option. I put this to the user, when it is set correctly it spreads to the customer as you can see in the file of configuration on the client computer, but it does not seem to enter into force.

  When a user is connected which has admin rights, and thus access to two local stores machine and the user must correctly a certificate store of the local computer. I know that there is a valid certificate in the store of users for these users as if I delete the local cert machine it takes so the cert of the user.

  No problem for users without admin rights they do not have access to the local computer store.

  Someone has any ideas why this doesn't work?

  Jason

  Hi Jason

  It seems that the ASA is actually still push the old profile to the client.

  From the CLI, check:

  cache dir: / SC/profiles

  more cache: / SC / profiles /.

  I guess this will show you the old profile.

  How do you have it change exactly? Using the profile in ASDM Editor? You push 'applies' later, do you have errors?

  In any case, use "disk0 more:" to verify that the profile on flash is correct (i.e. that there not the serverlist), then force the ASA to re - load this file using:

  conf t

  WebVPN
  SVC profiles disk0: /.

  Then check "hide: / stc / profiles /" once again to check it took it.

  HTH

  Herbert

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• Unable to connect using the Cisco VPN client

  Hi all. I recently configured a 5510 ASA to allow remote access using the Cisco VPN client. The problem is that everything works fine when I connect using a modem classic or on a computer with a public address that I use for testing purposes, but whenever I try to connect with on an ADSL line, I can't access to the resources. I have connection and after that nothing, I can not achieve anything.

  I enclose the relevant configuration information in the attachment. Any help is welcome.

  Depending on the version, add...

  ISAKMP nat-traversal

  or

  ISAKMP nat-traversal crypto

  Should be all you need.

• What are the ports used by the Cisco VPN Client?

  Hello

  I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

  I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

  What are the ports used by the Cisco VPN Client?

  Thank you

  You need to open:

  UDP 500

  ESP protocol

  You must also open the UDP 4500 port (if using NAT - T).

  In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

  1. If using IPSec over TCP 10000, then open TCP 10000.

  2. If using IPSec over UDP 10000, open UDP 1000.

• Impossible to install the Cisco VPN Client on Windows 7

  Hello

  After an uninstall successful VPN Cisco version 4. I try to install the Cisco VPN Client 5.0.07.0290 version.

  But after the launch of vpnclient_setup.msi, the wizard starts. When I click on the next button, I get the following message: "installation ended prematurely because of an error".

  As an attachment, I add the details of the discovery of the error in the logs of windows (logError.txt) and the logs generated by the MSI installer in verbose (log2.txt) mode.

  My computer is a lenovo W500 with Windows 7 64-bit and 4 GB of memory (compatible with the requirements of the Cisco VPN Client).

  I have administrative privileges on this computer.

  Please help me!

  I need to use it to connect to my corporate network.

  Thanks in advance.

  BR

  Jerome

  If you want to try another software, I know that works I used it up until cisco came out with a 64-bit client there. Is the 64-bit version of shrew 2.1.0 it worked very well, you will just need your file FCP of cisco for import into if you have. This will tell you if the client or your system at least.

• How to allow access to a local area network behind the cisco vpn client

  Hi, my question is about how to allow access to a local area network behind the cisco vpn client

  With the help of:

  • Cisco 5500 Series Adaptive Security Appliance (ASA) that is running version 8.2 software
  • Cisco VPN Client version 5.0 software

  Cisco VPN client allows to inject a local routes in the routing table Cisco ASA?

  Thank you.

  Hi Vladimir,.

  Unfortunately this is not a supported feature if you connect through the VPN Client. With VPN Client, that the VPN Client can access the VPN Client LAN host/local machine, not host from the local network to business as customer VPN is not designed for access from the local company network, but to the local corporate network.

  If you want to access from your local business to your LAN network, you need to configure LAN-to-LAN tunnel.

• multi-site VPN with just the cisco vpn client

  Hello everyone

  Please I need your help.

  We have a headquarters office and up to 60 is BranchOffice, we want to create VPN network between its. so let's deploy 2 router cisco esy vpn server with HA (HSRP) at the Headquarters Office and all branches have Connection ADSL and they will use just the cisco vpn client to connect to the Headquarters Office.

  My question is: is it possible to do it just with the client vpn cisco without purchased for any exercise bracnh a cisco router to create an ipsec tunnel because it is so expensive?

  It depends on if the routers to offices can handle NAT with several internal VPN clients to 1 IP address. Most of the new material should be fine. Keep in mind the maximum limit of the VPN client, with 60 agencies and 5 people each of whom you are above the limit.

  Michael

  Please note all useful posts

• Request concerning the sequence of updates for the Windows Update client in 2015

  I posted a query similar to this on a Microsoft Technet forum, but I have not yet received a response to the specific question that I asked.  I'm trying so this forum.

  I am running Windows 7 Home Premium SP1, but I did not intend to accept the free update of Windows 10.  I don't use automatic updates.  I use Windows Update manually and select the updates to install, even for these updates identified as Important.

  Since April 2015, there was a sequence of updates for the client Windows Update on Windows 7 (Windows 8).  I have the Windows 7 of those below list:

  KB2990214 (April 2015)

  KB3050265 (June 2015)

  KB3065987 (July 2015)

  KB3075851 (August 2015)

  KB3083324 (September 2015)

  KB3083710 (October 2015)

  KB3102810 (November 2015)

  KB3112343 (December 2015)

  (This list is probably less intimidating than it looks because the replaced October update Update September, which replaced the August update, which replaced the July update, which replaced the June updated.  "There are therefore basically just 4 updates.)

  The big question is, given that Windows 7 is available for several years, why, all of a sudden, there was this sequence of updates for the Windows Update client?  Because these updates began to occur at the time when the offer of a free upgrade to Windows 10 was announced, I could be forgiven for thinking that all of these updates are really directed towards the relaxation of the upgrade to Windows 10 via Windows Update, and that there is little or no advantage to systems that are not upgrading.  I am mistaken in this belief?  If not, precisely those who will benefit from my system, even if it is not upgraded to Windows 10?

  The updates that I currently installed, depending on the installed updates, are KB2990214 (April 2015), KB3075851 (August 2015), KB3083324 (September 2015) and KB3083710 (October 2015).

  In my view, there was a lack of transparency in the descriptions of these updates in the KB articles.  And, in one or two cases, information on the importance of an update in the article and in Windows Update has been inconsistent.  It would have been much clearer if each KB article stated for NOT upgrading to Windows 10 systems, if the update to the Windows Update client is important, as an option or completely irrelevant.

  Hello, Tiberius.

  Thank you for your response.

  I'm sorry for the late reply.

  I appreciate your time and your concern.

  You can read this article and check if it helps.
  Next update to Microsoft Update Client
  http://blogs.technet.com/b/Mu/archive/2014/06/24/upcoming-update-for-Windows-Update-client.aspx

  Please keep us informed.

  Thank you

• Unable to connect via the Cisco VPN Client

  Hello

  I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

  I am not able to connect and watch the journal on the SAA

  ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

  ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

  ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

  What could be the reason.

  Concerning

  Hi, I had this same problem, here is the solution:

  When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

  Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

  Well, change your strategy using MD5 isakmp / OF would do the trick.

• Evaluation version for the cisco secure access control server

  Hello

  I can get the trial version for the cisco secure access control server. IF SO pls send me the link.

  Thank you

  Hi Thomas,

  You can download ACS for windows 4.1 or 4.2 from the link below:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/ACS-win-eval

  For ACS 5.x, please visit cisco.com

  Download software > Security > Cisco Secure Access Control System 5.x > Secure Access Control System Software

  HTH

  Kind regards

  Jousset

  Please evaluate the useful messages-

• All necessary licenses on ASA 5510 for old Cisco VPN Client

  We're trying to migrate our firewall Watchguard to a Cisco ASA 5510, who bought some time ago. For some reason, all of our users have already installed the old Cisco VPN client. I think it will work. Are there licensing issues on the 5510 I had to be concerned with?  No matter what special config that needs to be done on the 5510?

  Fix. You don't require licensing of AnyConnect of any type of configuration and the use of IKEv1 IPsec remote access VPN (which use the old Cisco VPN client).

  You will be limited to 250 active IPsec peers (remote access more no matter what VPN site-to-site) by the platform (hardware) device capabilities that are enforced by the software.

• Configure the Cisco VPN client to pass through the VPN site-to-site (GUI)

  Hello

  I say hat the chain and responses I've seen to achieve this goal have been great...

  https://supportforums.Cisco.com/discussion/12234631/Cisco-ASA-5505-VPN-p...

  and

  https://supportforums.Cisco.com/document/12191196/AnyConnect-client-site...

  My question is "we will get this configuration by using the graphical user interface for someone who is not notified about the command line?"

  Thank you

  Of course, all this can be configured via ASDM.

  Looking at the second example you posted above, they point you first change:

  ACL split of the tunnel for the AnyConnect customer

  This Configuration > remote access VPN > network (Client) access > AnyConnect connection profile > (chose the profile and select Edit) > (choose "Manage" next to group policy) > Edit > advanced > Split Tunneling > ensure that the policy does not "Inherit" but rather "Tunnel network list below" > Unselect "Inherit" next to the network list, then 'manage '. Enter your networks you want in the GUI in this dialog box. Click OK all the way back to the main window ASDM and click on apply.

  You then change:

  Crypto ACL for the tunnel from Site to Site

  To do this, go to Configuration > VPN Site-to_site > connection profiles > (choose your profile and select edit) > add the VPN client address pool to the list of local network between protect networks. Yet once, click OK all the way back to the main window ASDM and click on apply.

  Then, allow the

  ASA to redirect back on the same interface traffic it receives

  .. is defined under Configuration > Device Setup > Interfaces. (check the box at the bottom of this screen). Click on apply

  Finally, there is the NAT exemption. For which go to Configuration > firewall > rules NAT. Add a NAT device rule before rules network object with Interface Source out, Source address your address pool VPN, the Destination address to include remote subnets and Action is Static Source NAT type source address and destination address remaining as original (i.e. without NAT). Once on OK all the way back to the main window ASDM and click on apply. Save and test.

  Good luck. Don't forget to note the brand and posts useful when your question is answered.

• Cisco anyconnect client

  I have a cisco with 3 group policies anyconnect.

  I can only with cisco select any connection.

  How can choose from three different groups

  On the ASA 'publish us' group names using the webvpn to group aliases attribute. For example:

   tunnel-group  webvpn-attributes group-alias  enable tunnel-group  webvpn-attributes group-alias  enable

  ... etc. When this is done, they will appear in the drop-down list for the customers to choose amongst, during the connection.

  Your ASA may have specific customers restricted to a specific profile. We would see that as a value of group-lock under username attributes.