Form factor of the Board mother OptiPlex 790 DT?

Similar Questions

• Form factor of the graphics cards that work with the Dell Optiplex 760 desktop computer?

  Hello

  So I recently got this Dell OptiPlex 760 desktop form factor that I really like and I would get a video card for it.

  It's the desktop form factor. The second largest next to the mini tower. There a 240W (or 250?) food I don't want to change. I would like a GPU that works with a supply of 240 w.

  I wish it were less than 60 dollars. I do some light games (Minecraft) and want to join a substantial amount of FPS with this game. Suggestions of the card?

  I'll give you more information.

  It fits into all THE MODELS except the USFF because USFF has no slots.  You will need to remove the flange size and use the version of low profile.

  cs_setInnerHtml ('video_9366bb5b-9fda-4cca-bfea-c4ec470df1e3', ");

  

  

  Maximum power allowed is 25W on low profile units.

  It is also why they Print 25W max on the 16 X video slot.

  Radeon HD 2400 XT 25 W TDP

  

  

  Here are valid Dell Low Profile PCI - e 16 X for this chassis - video cards

  XX347 ATI Radeon HD2400 Pro 256 MB, DVI - I, TV out
  YP477 ATI Radeon HD2400 Pro 256 MB, DVI - I, TV out
  CP309 ATI Radeon HD2400 XT, 256 MB, DMS-59, TV out
  XX355 ATI Radeon HD2400 XT, 256 MB, DMS-59, TV out

  cs_setInnerHtml ('video_af6d7d61-a142-4402-9efd-b4abb192eca2', ");

• Form factor of the Arduino R3 on FRDM-K64F pins available

  Hello

  I just got my board FRDM-K64F and I would like to add some sensors to it to test it. I read that the Board has a form factor of the Arduino R3™ pins available and I don't know what it means when I buy sensors (i2C, SPI, UART interfaces) to this Council. I understand that I can just connect any sensor with cables and a model but I thought perhaps this provision of the Arduino R3 pins is something that makes it easier?

  As you probably can see, my skills of HW a little bragging...

  Thank you very much

  Andy

  Hi Andy,.

  It's GPRS Shield V2.0 - Wiki.

• H330 form factor for the PSU

  Hallo!

  Can someone tell me what form factor POWER H330 block uses? It seems to be pretty close to a TFX but each TFX PSU I found a screw holes in different places on my desk. Is this the case?

  Just the ususal request on here it seems related to an update of the graphics card!

  Thank you very much

  Barry

  Hi PaddyPuter,

  Welcome to the Forums.

  Looking for spare parts, the Ideacentre H330 uses the following PSU:

  PS-FSP180-50NPL 110/220V/NO PFC

  PS 400WATTS PC9029-EL0G 110/220V 250W

  PS PSE 180-50NPL 110/220V/NO PFC

  PSU form factor resembles a Flex ATX.

  Concerning

• HP Compaq dc5800 small form factor or the internal speakers -?

  The HP Compaq dc5800 compact there speaker internal (s) in the box of the computer?

  I've only been able to get sound by connecting to the audio port with a speaker or a monitor.

  If she has internal speakers, I will ask the Linux Board why it doesn't.

  Hello:

  According to page 14 of the quickspecs below, it does.

  http://WWW8.HP.com/h20195/v2/GetDocument.aspx?DocName=c04290830

  All of my dc7xxx/80xx PC Elite have always had an internal speaker.

  See page 5 for a list of the HP items indicates are not supported under Linux.

  Do not forget that this info was from October 28, 2009, and perhaps things have changed about the backward compatibility of Linux info.

• I want to buy the usb 3.0 card and the wi - fi card for Pavilion Slimline s3760 form factor

  Please help me to locate the internal usb 3.0 card and the card WiFi for Pavilion slimline s3760. There been no wi - fi internal catd and usb 2.0 when I bought in 2009.  It is a small form factor of the cabinet, and so the cards normal donot enter. Also, will there be enough slots for the latter.

  Sorry for all the posts! Take a look at this one:

  http://www.Amazon.com/Koutech-SuperSpeed-adapter-low-profile-brackets/DP/B005FM8P3W/ref=sr_1_12?ie=UTF8&QID=1342556028&SR=8-12&keywords=low+profile+PCI+USB

  Here, it's to Koutech:

  http://www.koutech.com/prodDetail.asp?LineNumber=525

• Envy DV7: What size/form factor hard drive is in my laptop?

  Good evening.

  Well, my desire for two year, died the other day care of overheating the chronic problems that seem struck Envys at this time. My block of cooling died beforehand, that was probably the cause of the rise in temperature. Yep, that burning smell of rubber from the exhaust vents was kind of present that something was wrong, as well as the characters of ding strange wing that the display has been put in place and the intense heat of the keyboard who suddenly developed. Unfortunately, it was out of warranty. I really liked this PC, too.

  In any case, I would remove the hard disk that is inside to retrieve the data using an external hard drive enclosure but I need to know what size or form factor of the hard drive is to buy the appropriate forum. I guess it's a 2.5-inch form factor. Is this correct?

  Thank you very much

  Bob

  Yes, it is 2.5 inches. You can just buy SATA TO USB adapter:

  http://m.eBay.com/ITM/Anker-USB-3-0-to-SATA-3ft-converter-adapter-cable-for-2-5-3-5-inch-HDD-and-SSD-/221203585457

  Concerning

  Visruth

• OptiPlex 790 SFF need service tag

  I bought an Optiplex 790 SFF skeleton and found out that it doesn't have a label service all over her. How can I get a serial number for it? I can from Dell?

  Latest version of the BIOS for OptiPlex 790 is here. Serial number shouldn't matter...

  Read and follow the instructions carefully and turn off anti-virus suite first, if you install it in Windows.

  Keep in mind there is always a small chance a BIOS update fails and kill the motherboard. So upgrade at your own risk...

  Assuming that ST has not been removed from the BIOS, you should be able to find by using the free version of Belarc Advisor.

  EDIT: ieee488 types faster as I do!

• Form factor card mother Studio XPS 9100 / size?

  I'd like to see if I can move at my Studio XPS 9100 motherboard to a smaller form factor case, but I don't know the size of the Board of Directors. Looks like it came in a full tower case. Does anyone know what the smallest case, is that it will fit inside? Maybe Micro ATX?

  Studio XPS 9100 manual shows all connectors of the motherboard and their functions for wiring. The question is whether or not the jury it self is mounting holes are identical to a standard size ATX motherboard. If this is the case, then it should fit in an ATX mid tower size.

• Dell OptiPlex 760 ultra small form factor possible to add ddr3 ram?

  Hello world

  I have an old OptiPlex 760 ultra small form factor, and I just installed 10 windows, which runs most of the time without a hitch.

  This OptiPlex 760 has a processor Intel Core Duo E8600 in there. I've been googling and if I understand correctly, this processor supports ddr2 and ddr3 ram. Does this mean that I can put ddr3 ram in this machine?

  I also wonder if I add more than 4 GB of ram to it. I know officially it says max ram supported is 4 GB, but if I look at my MacBook it says max supported ram is 8 GB and I have 16 GB in it.

  So I wonder if this is the case even with my OptiPlex.

  Thank you.

  Sn0w0nS

  I put ddr3 ram in this machine?

  It depends on the chipset and since Crucial offers only DDR2 RAM for this system...

  It may or may not work with more than 4 GB. Look so all about these forums to see if anyone succeeded with more than 4 GB. At the very least, buy it from a source so it takes 8 GB does not work.

  And do not compare apples and...

• How to add SSD for Optiplex 755 (Small Form Factor)

  Hi-

  I want to add a SSD for my Optiplex 755 (Small Form Factor) boot drive while maintaining the HARD disk it came with and the player optical slimline. There is a SATA port on the motherboard, but there is no open Bay and not a lot of room in the chassis (I do not see a power open cable).

  Anyone know how or if I can add a SSD to 2.5 inches to this machine? Would need a power splitter? And it's even bothered to improve an Optiplex 755-10 Windows?

  Thanks in advance for any advice.

  -Lewis

  Adding a drive in the optical Bay is possible.  But you cannot run without the original hard disk on the desktop SFF and ULTRA-COMPACT models.

  http://www.newmodeus.com/shop/index.php?Main_Page=product_info&products_id=576

  http://www.newmodeus.com/shop/index.php?Main_Page=product_info&cPath=2_3&products_id=439

  

  

  You will get an error message on the thermal characteristics of the drive.

  SSD on SFF and USFF support have a problem due to heat dissipation.  The hard drive if not acknowledged will give an error, press F1 to continue.

  BIOS errors are;
  1 attention! Rear fan failure
  2 attention! Ambient temperature sensor not detected
  3 drive HARD replacement is not valid, continued use can result in
  long term reliability HDD delivers, please press f1 if you would
  like continue, and/or contact dell for a replacement HARD drive

  Strike F1 to continue F2 to run the Setup program, F5 to run onboard diagnostics

• HP Compaq 6300 small form: deliver the installation of an operating system for HP Compaq Small Form Factor 6300

  I have a HP Compaq 6300 Small Form Factor in which I just replaced the motherboad. It works very well. I can start on a USB bootable and (1) start a Windows 8 or a clean installation of Windows 10. I can (2). boot from a USB drive capable of Linux Mint 17.3 Startup and load that OS fine. When I try the installation of any of the aforementioned OSs (Windows 8/10-Linux Mint 17) they all will get an error of memory or hard drive and the installation at the beginning of the installation to fail. I tried this on two SSD drives and two HDs standard. I am at a loss on what to try next. Any help would be great. Thank you. -Matt

  I have it. It was a bad memory stick.

• HP Compaq dc7800p small form f: the upgrade of system model HP Compaq dc7800p Small Form Factor

  Right, I'm wanting to upgrade my ram and graphics card, but I am struggling to understand what I put in and what I can't. I also wouldn't mind research in a new soul who currently use a vpro intel Intel (r) Core (TM) 2 Duo CPU E6750 @ 2.66 GHz, 2660 Mhz. I just want to eventually play some games, but nothing heavy and do some light video editing again once nothing to heavy. Any help would be amazing.

  Here is the complete information of the system:

  Name of the Microsoft® Windows Vista™ operating system business
  Version 6.0.6002 Service Pack 2 Build 6002
  Another Description of the OS is not available
  Manufacturer of operating system Microsoft Corporation
  USER-computer name
  System manufacturer Hewlett-Packard
  Model HP Compaq dc7800p Small Form Factor system
  System Type X 86-based PC
  Processor Intel (r) Core (TM) 2 Duo CPU E6750 @ 2.66 GHz, 2660 Mhz, 2 Lossnay, 2 logical processors
  BIOS Version/Date Hewlett-Packard 786F1 v01.27, 11/04/2008

  I would also like to pass well ten Windows. Thank you

  Hello:

  For a video card, I recommend the AMD Radeon HD 6450 half-height card, which works perfectly with the 240W power supply in your PC.

  Make sure that you get one that includes low profile brackets in the area.

  Memory... you can install a maximum of 4 x 2 GB memory PC2-6400 for your model if you are running a 64-bit operating system.

  I have used this brand in my dc7800 CMT.  I bought 2 games and maxed out.

  http://www.Newegg.com/product/product.aspx?item=N82E16820231207

  Processors... Mine came with the E8300, so I didn't change that.

  Here is the link to the quickspecs for your PC.  You can find taken processors supported on page 9.

  http://WWW8.HP.com/h20195/v2/GetPDF.aspx/c04287277.PDF

• HP Compaq 8200 Elite - XL510AV: need help to find the form factor small PCI Ethernet card

  Hi guys, I hope one of you can help me with this. I need a card PCI Ethernet single port for a HP Compaq 8200 Elite Small Form Factor computer.

  From what I see, the motherboard has a PCIe and two PCI card slots.

  Computer model is XL510AV

  Any help is appreciated.

  Hello

  The following can help:

  http://www.StarTech.com/au/networking-IO/adapter-cards/10100-1000-Mbps-32-bit-PCI-Gigabit-Ethernet-card~ST1000BT32

  It has 2 brackets for standard and one for the low profile, you can swap around.

  Kind regards.

• Pavilion Touchsmart all-in-One: how to install the SSD in Touchsmart F234? What form factor is necessary?

  Will be HP 20-f234 enhancement by replacing the HDD with SSD.  Two questions:

  1. is there a video (or even a set of complete step by step instructions would be) Bay of any place that illustrates how to get the HARD disk inside?  (Remove screws, etc.)

  2. what form factor SSD is supported?  That is, will I need an adapter of some sort support if I have a 2.5 SSD "?

  Thank you.

  Seems to be a 3.5 "desktop drive

  How to replace the hard drive

  http://support.HP.com/us-en/product/HP-Pavilion-20-all-in-one-desktop-PC-series/5359028/model/5365334/document/c03690508/

  Your support page

  http://support.HP.com/us-en/product/HP-Pavilion-TouchSmart-20-F200-all-in-one-desktop-PC-series/5359028/model/5365334/how-to