Gateway to Comcast Business class SMCD3G-CCR and Cisco 2960 G switch
Hello
I'm looking to upgrade my silent switches to a Cisco 2960 switch. I wanted to check and make sure that this configuration would be funded.
I need to configure the 4 VLANS on Cisco 2960 switch, 1 for the vmotion traffic, which would have no internet access, one for management traffic that does not have internet access, for standard server traffic and traffic vmserver, who should access to the internet.
The Cisco switch working with gateway SMCD3G-CCR ok, or do I need another router for this? If yes why?
I don't know if this is the right forum but I know that Cisco linksys bough, so I hope someone can point me in the right direction.
Thank you
Hello.
These products are processed by the Cisco Small Business Support Community.
* If my post answered your question, please mark it as "acceptable Solution".
Thank you!
Tags: Linksys Products
Similar Questions
-
Hi Experts,
I have some confusion with the button Mode with cisco 2960/3560 switches.
I read on many forums and articles, but where things are not clear.
a place given 3 seconds and somewhere is given 7 or 10 seconds.
Qus1), what is the exact time to press/hold Mode button to perform two following tasks:
A. password recovery (according to my knowledge 3 sec) good or bad?
Configuration of the switch (start + run) would be safe
After the recovery of password? Yes or no
B. factory default (according to my knowledge 10 dry) good or bad?
I'm afraid, because if I press mode button more than 3 seconds, then
It will delete any configuration of cisco switch. Yes or no
Qus2) I want to recover the catalyst 2960/3560 switch password without
Start/run configuration to lose. That is my main concern.
Please tell me how to do this, what will be the time keeping Mode buttom
in a few seconds?
Qus3) which means this line
"If the password recovery mechanism is disabled in switch
then you will lose all the config.
This sentence has been given on this forum url
https://supportforums.Cisco.com/thread/140848
KS
Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.
Use the following terminal settings:
Bits per second (baud): 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: Xon/Xoff
Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.
Unplug the power cable.
The power switch and take it to the switch: command prompt:
2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:
Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.
2960, 2970 Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green. 3560, 3750 Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green. The system was interrupted before the flash at the end file system initialization
loading the operating system software:
flash_init
load_helper
boot
switch:
Run the flash_init command.
switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.
Run the load_helper command.
switch: load_helper switch:
Question the dir flash: command.
Note: Be sure to type a colon ":" after the dir flash.
Appears in the file system of the switch:
switch: dir flash: Directory of flash:/ 2 -rwx 1803357 c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4 -rwx 1131 config.text !--- This is the configuration file. 5 -rwx 109 info 6 -rwx 389 env_vars 7 drwx 640 html 18 -rwx 109 info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.
Type rename flash: flash: config.old config.text to rename the configuration file.
switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.
Issue the boot command to boot the system.
switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.
Enter "n" at the prompt to abort the initial configuration dialog box.
--- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.
At the switch prompt, type en to enter a mode.
Switch>en Switch#
Password recovery
Type rename flash: config.old flash: config.text to rename the configuration file with its original name.
Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#
Copy the configuration file in the memory.
Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#
The configuration file is now reloaded.
Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.
Note: Replace passwords that are required. You must crush not all passwords listed.
Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password
Write the running configuration in the configuration file with the write memory command.
Sw1#write memory Building configuration... [OK] Sw1#
For factory reset:
do not give under the control of factory reset
Switch#copy flash:config.text system:running-config
can I copy the running configuration to Flash
Switch flash running-config #copy:
Destination file name [running-config]?
Building configuration...
[OK]
Switch #copy running-config startup-config
Name of destination file [startup-config]?
Building configuration...
[OK]
Review the link for more information below
Please note the useful messages.
Concerning
Vesta
"Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. " -
can I buy a 600 GB 15.7 k sas 3.5 Cheetah without having the business class dell model? I could put any 15.7 k sas model in a dell and it is not compatible.
any help would be greatly appreciated as im new too servers.
You can, and it can work properly. All certified disk includes the risk of bad contact with the controller. So, the answer is 'yes', but at your own risk. Dell will also help you solve the problems of storage without certified readers, so if you go credits/retail, get ready to make your own troubleshooting - or be able to make experts if necessary.
You may NOT USE the SME players on the controllers of the company although.
-
problems of class ASA5510 dsl and business
Here's my setup.
Business class dsl modem with a static IP (100.0.0.1) connects to an asa5510.
the ISP gave me another static routable ip address for the asa5510 and I configured the 5510 outside interface with this (100.0.0.2).
I have also some machines behind the inside interface of the 5510. (172.16.1.0)
All I want to do is let some ppl vpn inside network to make a diagnosis.
I don't need someone inside to access the net, so no nat is necessary.
I crossed the normal config vpn and remote vpn Wizard.
However, by using the cisco vpn client, I am unable to connect.
I ping the 100.0.0.1 interface, but is unable to vpn in.
I think that there is no path of 100.0.0.1 100.0.0.2
any suggestions?
The group name must be EAT that is configured on the tunnel-group settings in your ASA. Do not "vgoradia", but what is configured on the SAA.
And the password must be one that you have configured in the tunnel-group for pre-shared key parameter.
tunnel-group EAT type ipsec-ra
tunnel-group EAT general attributes
address vpnpool pool
Group Policy - by default-EAT
tunnel-group EAT ipsec-attributes
pre-shared-key *.
Let me know how this pans.
The rate of this post, if that helps.
Thank you
Gilbert
-
Hello, my phone pulled from my class at school and it has no data on it, so I did not no how to locate without using find my iphone is there another way I could find as soon as possible
Go to iCloud.com
Then sign in with your Apple ID and password, then click the Find iPhone.
If this does not help, see: If find my iPhone is not activated on your missing device > what to do if your iOS device is lost or stolen
-
I recently took a class of Microsoft and received the "Welcome" e-mail, but could not connect with the supplied credentials (example below):
Your MC ID: xxxxxxx
Your temporary access code: 18995EBE-BDAF-4883-8F95-64D18D261848
I created a new account with the e-mail MC ID has been sent and it was not recognized. I would like to merge (link) the news and be able to get a fresh copy of my cert. Thank you.
Hello
I suggest you contact Microsoft Learning support team to improve assistance:
http://www.Microsoft.com/learning/en/us/help/assisted-support.aspx
-
Why continue those class Scheduler start and stop every half hour approximately
Why continue those class Scheduler start and stop every half hour approximately. I am fortunate to have a sound event for the event program open and this event is triggered by Multimedia Class Scheduler, it seems, every half hour.
Is this normal?
Can I disable it?James
Hello
Service Multimedia Class Scheduler (MMCSS) allows multimedia applications to ensure that time-sensitive processing receives priority access to the CPU resources. This service allows multimedia applications to use CPU as possible without denying CPU for low-priority applications as well.
This service is required only for the fact that the Windows Audio service lists this as a dependency. Without the Windows Audio service, no audio signal will play on the system. This service is started when the system starts, but shortly after (~ 8 minutes), it stops.
This is a Notification which will start with all programs that use Windows Audio. For an example if you open Windows Media Player, then multimedia class scheduler also starts because it uses the windows audio.
-
Trying to convert a trial to paid membership, but the payment gateway is showing the location in India and in Indian currency. I am based in the United States have changed in the account setting too but the gateway payment does not seem to change.
Hi Khushboo,
On the bottom of the page of Adobe, you will see an option to change the region, make sure that you have the United States he and on the purchase page to change your currency to the U.S. dollar as well.
Let me know if it helps.
Concerning
Sarika
-
Hello
Re: External CSS to model; I finished a Web site for the class (html 5 and I forgot to select the external CSS stylesheet; do I have to redo the project in Dreamweaver CS6)
In 2015, CC, you can do the following...
1. turn highlight everything between your
-
I can't post a temporary site in catalyst for business. It stops and it appears: Internal Error 400 Bad Request (117007)
Hello
Have one inserted a form Widget into Muse.
Please ensure that the email entered by you is correct email format in the field "Email to" Option form.
Link below had the similar problem.
Concerning
Vivek
-
LACP hash between N3048 and CISCO SG300/SG200 + question Twinax attach direct cable
Hello
In my network I have deployed two new N3048 with 2 transceivers SPF + and SPF module back + as core switches are connected to other 3 switches from edge of N2048 using optical fiber and I reused my previous CISCO SG300 and SG200 goes to serve the other two boxes of my campus via the spine in copper.
I have 4 copper cable which starts from the hub of the SG300 network and 2 the SG200 brass. I set up to have a redundant connection using 2 + 2 with SG300 and 1 + 1 with SG200 RSTP.
So for the SG300 I re LAG + LACP to have two channels of the N3048s port, but now that a single cable is connected because I don't know what kind of LACP hash mode should I put on N3048 to have a compatible hash between Dell and Cisco switches.
My N3048 have mode 7 (Advanced hash) as default but I guess that cisco models do not understand... so, what mode is the best for LACP work perfectly with small business cisco switches?
I also received my twinax cables to connect my two N3048 via SPF + back modules... conhot can I plug the cables into the slots SPF + (already mounted) without turning off my basic switches?
Thank you!
See you soon
Cables can be connected/disconnected, but I don't know if the real module SFP + for the rear of the N3000 is hot plug.
-
Unable to connect to network WPA2 with Windows 7 64-bit (Intel 4965 and Cisco WUSB600N)
Connect to a WPA2 network seems to be a fairly common problem. Again, I can't be able to find a solution.
OS: Windows 7 Ultimate 64-bit
Wireless adapter (s): Intel 4965AGN (integrated into Dell XPSM1330) and Cisco/Linksys WUSB600N
Drivers: latest windows 7 64 bit drivers from the two websites of companies. Intel (v12.4.1.4), Linksys (3.0.10.0)
Network properties: WPA2 enterprise, encryption of the ACS, authentication EAP - P, several types of routers around the world
History: has been able to use the same laptop with Vista32 on this network without any problem
I can not connect to networks non - WPA WPA networks simply not.
When you try to connect to my companies WPA2 network (at any of our locations around the world).
Method #1:
- Select "Other network" in the list of network
- Enter the SSID of the network
- Windows could not connect to the SSID
Method #2- Open network and sharing Center
- Select set up a new connection or network
- Select manually connect to a wireless network
- Select one of my adapters
- Enter the SSID, as WPA2-Enterprise security type, type of encryption like AES, check the boxes to connect automatically and connect even if the network is not broadcasting
- An unexpected error has occurred
Method #3: Try to trick windows- Open network and sharing Center
- Select set up a new connection or network
- Select manually connect to a wireless network
- Select one of my adapters
- Enter the SSID but select an open network
- Adds the network
- Then try to change properties
- WPA2-Enterprise security type
- Set to AES encryption type
- "Choose a network authentication method:" drop-down menu is empty!
- Windows has encountered an error saving the wireless profile. Specific error: the profile has an invalid length field.
I'm pretty desperate for a solution.Kind regardsJohnThere are a few people with Win7 x 64 that cannot connect to WPA2 P/EAP Corporate/business networks and no solution?
Come on, guys, it's the microsoft answers site! someone give me something! I have two asus laptops, both with network cards Intel having this problem on two networks separate enterprise (school).
Edit:
RESOLVED:
Here's the thread of the resolution:
http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/unable-to-connect-to-company-wireless-network/3bcd12b1-A0D8-4357-bded-07da96259920?page=3
The problem occurs when you perform a Wizard for easy transfer to a computer that was Symantec Endpoint Protection installed to one without him.
Answer, copypasted:
Inspect the key mentioned above - that is of HKLM\System\CurrentControlSet\services\RasMan\PPP\EAP.
In each of the number keys look something like ConfigPathBackup and its corresponding ConfigPath - there are a number of them.
For each, I deleted the original key (e.g., ConfigPath) and restored the original by renaming ConfigPathBackup to ConfigPath
For each of them, the State is now restored to her pre State Symantec - each key pointed to a Symantec location that is no longer present and by restoring the path key backs up everything was fine
-
RT for Windows and Cisco VPN (AnyConnect) Solutions?
Microsoft and Cisco are working together to ensure Cisco VPN is soon available for Windows RT? I read a thread RT of Windows from Microsoft and Cisco VPN without seeing all the comments of Microsoft or Cisco. Please notify.
Hi Gabriel,
The Microsoft Answers community focuses on the context of use. Please reach out to the business community of COMPUTING in the TechNet forum below:
-
Original title: how to uninstall client services for netware?
When I change how a user connects power on and off a screen appears saying "client for Netware has disabled the Welcome screen and the fast user switching. To restore these features, you must uninstall client services for Netware... But it is impossible to find... Help?
Hello LindsayJune,
Click the Start button.
Click on Control Panel. Select network connections
Right click on 'Connect to the Local network', then click 'properties '.
Search for "Client Service for NetWare" slot "this connection uses the following items."
Click it, and then click the "Uninstall" button
Restart your computer.Uninstall client for Netware feature will allow the option of quick change of user on your computer.
I hope this helps.
-
The switch on my fast computer of user function has been disabled on my computer. When I try to use this function. I get the following message.
A recently installed program has disabled the Welcome screen and the fast user switching. To restore these features, you must uninstall the program
. The following file can help you identify the program that made the change. GT Gina.dll
* original title - I have a windows xp. Under user accounts, choose a task. Under change the way users log on and outside. I get a message that the function of the Welcome screen has been blocked *.
Hello
You can try the steps outlined in the article below and check out them.
The logon screen "Welcome to Windows" does not appear when you start the computer
http://support.Microsoft.com/kb/817142
Maybe you are looking for
-
See the Photos in both windows
I often move photos between albums and the duplication of the photos in different albums. Is it possible to open two windows to display the Photos? I had a play around with split view but cannot get pictures to sit next to another application, as opp
-
to turn off printer 2 faces, and the author of the previous question link does not work
-
When I select 'contacts', 'manage' does not appear. Can someone help me?
-
I feel oxc004e003 error after reformat and reinstall my Windows 7 Professional x 64
Diagnostic report (1.9.0027.0):-----------------------------------------Validation of Windows data--> Validation code: 0Code of Validation caching online: 0x0Windows product key: *-* - MV8MH - 98QJM-24367The Windows Product Key hash: wgci5Gdejx4esg7
-
NetBook Asus Eee disconnects me from the internet whenever it goes into sleep mode.
I just got an Asus Eee netbook with Windows 7 Starter installed. Whenever the laptop goes to sleep or sleep, he disconnects the internet and refuses to reconnect. The only way I can make it work is off my home router and reset the system. It's annoyi