General on the raid controller and hardware

Similar Questions

• Install the raid controller during the installation of ESXi5

  Hello

  Today, we plan to install ESXi5 on our server.

  We had no problems during the installation of ESX4.1 as he ask custom drivers when it starts.

  But ESXi5.0.0 does not ask for the installation of the custom driver and we cannot install raid controller driver!

  I do not know how to resolve this so I wanted to know is possible to install the raid controller?

  Thanks in advance.

  I know I ask too many questions, but I know a little bit about it.

  No problem, that's what the forum is done

  Now should after you download the Image how I use it?

  Burn the image to a CD and run the installation from the bootable CD. Remember, though, that the image is usable only for new installations, not for upgrades (see release notes).

  André

• Problems with the Ethernet controller and PCI Satellite L30-10 X device driver

  HelloW!

  Sorry for my bad English, I'm from the Russia.
  A few days ago, I bought Satellite L30 - 10 X with W Vista on board. In my opinion, that this OS does ' t very good on this computer, so I install W XP.

  I have some problems with drivers. At first, I don't know which model I have: PSL30 or PSL33? I have download all the drivers for the two models. But after installation, computer doen't find the drivers for the Ethernet controller and PCI device...

  Hello

  Satellite L30-10 X belongs to the series of PSL33E. This number located on the label on the bottom of the device!

  You must choose this number in the form of driver download for XP compatible drivers.
  I put t know why you are not able to install the LAN driver. I have the same laptop with Vista and I've install the XP and all the drivers will work perfectly.

  I assume that you have installed the drivers in the wrong order. Please take look in the Toshiba installation instructions txt file. In this order, install the driver! This is important.

  I think that you should install XP again to ensure that the registry clean, then download and install the XP drivers compatible as mentioned in the installation instructions file.

  Good luck

• How to restore the multimedia controller and multimedia video controller to the system?

  How to restore the multimedia controller and multimedia video controller to the system? These items are indicated with yellow exclamation point in the conflict. How to solve these elements to correct the situation?

  Scan your computer with Speccy, Pc Wizart or SIW software and download the driver from manifacturied of the material.

• The RAID controller compatibility

  Hi I just bought a new system and intend to use a RAID controller to configure a RAID array.

  The controller that is available is ""Intel RS25DB080"." I've never done this before so to start I wanted to ask you how can I check if it is compatible with my x 99 Deluxe motherboard?

  (he did not appear on the page that mentions the compatible products: Specifications of RS25DB080 for the Intel® RAID controller)

  Secondly, it would be possible to set up several RAID arrays using a single controller? that is, if I want to do a table composed of 3 disks and another 3 more I have to buy an extra card?

  Also if this controller is not compatible what other controller I'll buy? And what exactly what I look for in a RAID controller if I'm looking for one? (Currently I just check to see if it's a SATA or SAS controller)

  So, basically, do not know much about the RAID needs your help, thank you!

  Generally if you are serious about RAID for the only real video editing solution is arec, because you will need 3 RAID or Raid 6.  There are a number of X 99 different systems with the Areca RAID card installed I am owner of a BOW 1883i, which works very well in my x 99 motherboard, I have it configured with 7 discs each RAID 3 Samsung 840 Pro I probably will be getting rid of it I can get nearly the same results with a SSD of unique m2.  In my old age, I went basic/simple rather than exotic.

• ESX4i does not see the RAID controller card

  I install the ESX4 and the ESXi4. Considering that ESX sess card RAID controller, ESXi4 will not work. I was wondering if there was a solution to this?

  Memory I don't remember ESXi4 support adding additional drivers (unlike ESX4 Installer) but I was wondering if I climbed to U1 ESX4i, that would help. Or is just "not supported"?

  Concerning

  Mike Landry

  www.RTFM-Ed.co.uk

  My problem has been resolved by the way of the ESXi 4.0 to ESXi 4.0 Update 1... which includes a driver update...

  I managed to ESXi in order to run from a USB key on the servers, but found the previous day, and DPM mode did not work properley. While he was going to suspend the ESX box very well, the machine just and seems to lose its settings to boot PXE boot - regardless of what I did with the BIOS...

  I found ESX4i U1 to install on the physical disk is more reliable...

  Concerning

  Mike

• Insertion/thanks to the RAID controller plug in PCIe card in a UCS C220 M3, rather than embeded RAID controller?

  Hello!!

  We have a UCS C220 M3 server with a 1 TB SAS hard drive and a controller RAID embeded, like this:

  1	UCS-HDD1TI2F212	1 TB SAS 7.2 K rpm 3.5 inch HDD/hot plug/disc horse sleigh
  1	UCSC-RAID-ROM15	Embedded SW RAID 0, 1, 10, 5, 4 SAS/SATA ports

  If I add this controller RAID PCI card to my UCS server:

  UCS-RAID-9266CV =

  MegaRAID 9266CV-8i w/TFM + Super CAP

  US $ 1,686.00

  Going to work with her, ignoring the old RAID embeded it configured?

  The question is that VMWARE is not supported controllers shipped my RAID, so I want to add an external RAID PCI controller to support VMWARE.

  I don't know if it will work.

  Thank you!!

  Rodrigo,

  The embeded controller is built and not removable, it is integrated into each C220/C240. The units are designed to operate with PCIe controllers and mezzanine table when it is properly configured.

  Once you install the controller of the SIPC, you will need to do the following:

  (1) move the conectors mini SAS to the motherboard in the LSI PCIe controller

  (2) make sure that the slot PCIe what optionrom is enabled in the BIOS. (newer systems have their OptionROM disabled in the uninhabited slots (from the factory). If you do not see the OptionROM for the POST, then go back into the BIOS and enable the slot PCIe OptionROM

  (3) while you are in the BIOS, you can thus turn off Patsburg UCS regulatory table (the table embeded). It is of no use at this stage that you removed the cables up to the HARD drive Bay. It is also misleading if left active, you will see the configuration of arrays of LSI utility appear twice during POST. Time for the embeded and once again for the PCIe LSI controller.

  Dave

• Signature LUN after replacement of the RAID controller

  I have the following scenario:

  I had a Cisco UCS server with an LSI controller. I needed to replace the controller to another, the same form, different model.

  I've done the replacement physical, powered on the server. ESXi starts fine, but no data store appears. Data warehouses are on the local hard drive. There is no remote storage.

  When I try to add the data store, I had 2 options of mainly:

  -Keep the existing signature

  -A new signature assing.

  I'm sure both will work, and I'd go with the first.

  However, I would like to know what impact the selection of one of these options. Similar cases, I will, will that be the best since I'm on a new material for RAID controller?

  Or would it not matter at all if I keep the same signature?

  I have beenr of reading on these 2 options, and for local storage, they do not seem to make any difference, but would like to know any other thoughts.

  I kinda fear Award for a new signature.

  Thank you.

  Due to the replacement of the controller, the ESXi host now recognizes the LUN as a snapshot LUN, it contains a signature known, but it is presented to another controller. Given that you can ensure that the logic unit number is unique, I don't see a requirement for resignaturing it.

  André

• HP 15 laptop: I need the network controller and pilot controller video 3D

  Hello I need network controller and 3D video controller driver
  
  Network controller:
  PCI\VEN_10EC & DEV_B723 & SUBSYS_2231103C & REV_00
  
  3D VIDEO CONTROLLER:
  PCI\VEN_10DE & DEV_1140 & SUBSYS_2337103C & REV_A1

  Hello:

  You need these drivers...

  Network controller

  This package contains the installation package driver for the controller wireless LAN Realtek RTL8188EE in the laptop models running a supported operating system.

  File name: sp69033.exe

  3D VIDEO CONTROLLER:

  This package contains the driver that allows the of laptops from NVIDIA Graphicsin supported models that are running a supported operating system.

  File name: sp67265.exe

• I opened my control panel, click the game controller and his party. How can I get that back

  my game controller is gone he was there and now his party. Can I use my game controller some how the driver who was on my computer that control the game controller is gone and I don't know where he is and what has happened. can someone show me how to or tell me how to recover my controller. send me a link.
  Thank you

  Hi Reynard7,

  1. what game controller you are using?

  2 did you change on your computer before this problem?

  You can perform the system restore to revert to the previous state when it was working fine:

  a. click Start, type system restore in the Search box and then in the list click on the system restore program.

  If you are prompted for an administrator password or a confirmation, type your password or click continue.

  b. in the System Restore dialog box, click choose a different restore pointand then click Next.

  c. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  d. click Finish.

  System Restore: frequently asked questions

  Hope the helps of information.

• Remove the secondary controller and tertiary high availability for each access point

  I want to remove secondary and tertiary sector controller of high availability for each access point. I have more than 900 APs associated with a Version of the WLC 8510 8.0.121.0 software. What is the best/better way to remove secondary and tertiary controller?
  Or I can create a model first. We use version 2.2

  Hello

  Easiest way:

  Yes you can do this by using the first Cisco Infrastructure, you can create a Setup AP Lightweight model to specify the name of the PDC and the IP address and specify an empty value (choose the first empty option in the drop-down list) and 0.0.0.0 for the secondary and tertiary sector controllers.  Then you can apply this model to the AP, and she must remove (virgins all) values for these fields.

  Long way:

  Yes there is no clean way to remove it from the CLI. you need to manually remove each on the AP.

  Concerning

  Remember messages useful rates

• Help to find the tab "Audio and hardware Configuration"

  I use Adobe Audition 1.5.  One of the solutions to a problem that I have is to check the settings in "Audio and hardware Configuration".  I can't find this tab

  at the Audition 1.5.  Can anyone describe where I can access the "audio configuration"?

  Henryr1490

  In the Options menu. Properties of the device. Then, you have to Wave and wave of the other tabs. Also, you may also need to set device stopped in the same Options menu.

• "Application cannot be started. Contact the application provider' but I have the right software and hardware.

  Windows 8.1

  THAT IS TO SAY 11

  XPS 8700

  Get several times, "Application cannot be started.  Contact the application provider.  I recorded and also tried to open it from the site.  I always run as administrator.

  The application is malware or is not certified WHQL.  64-bit versions of windows DO NOT ALLOW any application or driver or hardware to run or install if they are not certified WHQL.

  This is not the dell software and not supported here.

• The UPGRADE software and hardware Mac

  I always use the InD CS2 on a G4, running 10.4.11 (Tiger), using a 22blueIV LaCie monitor. Considering an upgrade, but have read on this forum of incompatibility of CS4 and Snow Leopard. Have to wait a while until that software is no longer compatible?

  Also to wonder about a Mac Pro or iMac, use mainly InD and PS.

  All comments and suggestions appreciated regarding software and hardware.

  What budget do you have?

  As for the CS4/Snow Leopard, nothing major thing I've seen.

  Bob

• Downloaded CD player and took my XI from Adobe.  I wasn't able to use the domain controller and want to have my back XI.  How can I do this without losing the Adobe?

  @Can you please show me how I can get rid of the DC Adobe and return to my XI.  I can't use this program to DC.

  Margery John Ziemann

  {Removed by hpst phone number]

  Hi margery,

  Uninstall the CD, reboot your system and install Reader 11 using this link Adobe - Adobe Acrobat Reader DC Distribution.

  Kind regards
  Nicos