Getting the name of the Member on the mouse upwards

Similar Questions

• Get the mouse cursor

  Is there a way to get current mouse pointer?  I know there is a function to change, but I want to know what it is currently.

  The reason for this is because I have a multicolumn listbox.  And on the mouse upward I have code that detects which column you clicked on and sorting on this column.  But I also welcome to adjust the column width.  The problem is that if you adjust the width it is also listed as a mouse to the top and will sort the column when the user did not want to do that.

  My simple solution was to look at the current mouse cursor and it's one that is used to adjust the size of the column, on the mouse upward, then simply ignore the event.  Any thoughts?  Thank you.

  Have you tried the method of the click column heading on get to MCLB?  It returns a - 2 when resizing the column headers

  

• S2S VPN - cannot get the tunnel upward

  I couldn't lift a VPN site-to site because of a configuration error that I can't fix

  The topology is Server1 > Hub > ASA - 1 ASA-2<><>

  When I launch a ping server 1 Server 2 to try to get out of the tunnel to the top, I get the following error:

  % ASA-6-110002: unable to locate the output for ICMP inside:192.168.100.2/2655 to 192.168.200.2/0 interface

  No matter which side I am ping, I get the error on both of the ASA. Here is the config for the two ASA, thanks for any help.

  !
  ASA-1 hostname
  !
  interface GigabitEthernet0
  nameif outside
  security-level 0
  IP 80.1.1.1 255.255.255.252
  !
  interface GigabitEthernet1
  nameif inside
  security-level 100
  IP 192.168.100.1 address 255.255.255.0
  !
  passive FTP mode
  network of the PC_LAN object
  255.255.255.0 subnet 192.168.100.0
  network of the REMOTE_LAN object
  192.168.200.0 subnet 255.255.255.0
  extended access list ACL-OUTSIDE-PING icmp permitted any one
  LAB_S2S_VPN to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.200.0 255.255.255.0 connect
  LAB_S2S_VPN list extended access allow icmp 192.168.100.0 255.255.255.0 192.168.200.0 255.255.255.0 connect
  pager lines 24
  Enable logging
  exploitation forest-size of the buffer of 6000
  debug logging in buffered memory
  Outside 1500 MTU
  Within 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ARP timeout 14400
  NAT static PC_LAN PC_LAN destination (indoor, outdoor) static source REMOTE_LAN REMOTE_LAN
  Access-Group ACL-OUTSIDE-PING to the interface inside
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec transform-set ikev1 aes-esp - SHA-AES-ESP esp-sha-hmac
  card crypto VPN_CRYPTO_MAP 1 corresponds to the address LAB_S2S_VPN
  card crypto VPN_CRYPTO_MAP 1 set peer 80.1.1.2
  card crypto VPN_CRYPTO_MAP 1 set transform-set ESP-AES-SHA ikev1
  VPN_CRYPTO_MAP interface card crypto outside
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  management-access inside
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  tunnel-group 80.1.1.2 type ipsec-l2l
  IPSec-attributes tunnel-group 80.1.1.2
  IKEv1 pre-shared-key *.

  ASA-2 host name
  !
  interface GigabitEthernet0
  nameif outside
  security-level 0
  IP 80.1.1.2 255.255.255.252
  !
  interface GigabitEthernet1
  nameif inside
  security-level 100
  192.168.200.1 IP address 255.255.255.0
  !
  interface GigabitEthernet2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  passive FTP mode
  network of the PC_LAN object
  192.168.200.0 subnet 255.255.255.0
  network of the REMOTE_LAN object
  255.255.255.0 subnet 192.168.100.0
  extended access list ACL-OUTSIDE-PING icmp permitted any one
  LAB_S2S_VPN to access extended list ip 192.168.200.0 allow 255.255.255.0 192.168.100.0 255.255.255.0 connect
  LAB_S2S_VPN list extended access allow icmp 192.168.200.0 255.255.255.0 192.168.100.0 255.255.255.0 connect
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  NAT static REMOTE_LAN REMOTE_LAN destination (indoor, outdoor) static source PC_LAN PC_LAN
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec transform-set ikev1 aes-esp - SHA-AES-ESP esp-sha-hmac
  card crypto VPN_CRYPTO_MAP 1 corresponds to the address LAB_S2S_VPN
  card crypto VPN_CRYPTO_MAP 1 set peer 80.1.1.1
  card crypto VPN_CRYPTO_MAP 1 set transform-set ESP-AES-SHA ikev1
  VPN_CRYPTO_MAP interface card crypto outside
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  tunnel-group 80.1.1.1 type ipsec-l2l
  IPSec-attributes tunnel-group 80.1.1.1
  IKEv1 pre-shared-key *.
  !

  You won't have a road to 192.168.200.2 so he was not able to locate the next hop for the traffic of the tunnel.

  These static routes adding causes all traffic to be sent to the default gateway of the internet, including VPN and VPN traffic not.
  So adding a route for 192.168.200.0 pointing to 80.1.1.X gave the same results.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Anyone know how to get the mouse pointer visible on the extended screen?

  Well, I finally managed to work on a way to project my w4 iconia on my TV.  So grateful to a number of people in the community for me that far, but every step seems to bring his own fresh problem to enter.  so a few questions:

  1. anyone who manages to get the iconia w4 to duplicate rather than extend?

  2 - does anyone know how I can control the expanded view - I have a mouse plugged into my iconia so that I can flip through the window I want to show it on the extended screen but the mouse pointer does not appear as visible on the display (TV) extended although it does not work but the shooting blind is very frustrating - okay, if I watch a movie as soon as it runs on the extended screen it does not much you must handle but assuming I want to just browse the internet and project that onto the extended screen, so it's a big problem.

  My apologies if these are stupid questions, I'm not very technically savvy.

  TYIA

  This seems odd. I always change an extra-large pointer and traces of mouse long but have never had a problem with the HDMI screens like that.

  What is the brand and model of your TV please? Maybe someone can duplicate.

• How can I get the mouse on properties of the mouse wheel

  It was there at the same time, I can't scorrol upwards or downwards

  Hello

  1. don't you make changes to your computer before the problem?
  2. What is the serial number and model of the mouse?
  3 - is a General USB mouse or advanced mouse?

  Follow the steps mentioned below and check if the problem persists.

  Step 1:

  It is very likely that the mouse driver was not fully detected or compatible with windows 7.  If you have a mouse advanced, I would say that you go to the manufacturer's Web site to download the compatible driver for windows 7.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Step 2:

  You mentioned the presence of the rims option, in this case, I would have you to perform a System Restore to the point your mouse was working normally.

• Drag the mouse upward on the application icon

  Hello

  Just got a new drive installed and I lost this action! It's the same action by clicking on the icon of mission control

  Someone at - it help him?

  For me it is scanning to three fingers. Check the Trackpad system preferences tab more than movements.

• having the iPad several years; I forgot the password. Tried to restore; Unable to get the new software on my Macbook to charge; always disabled iPad

  have older Ipads; I forgot the password; now disabled. Tried restore several times. My Macbook won't download new software. Several error messages.  iPad now could not be restored and open

  Hey domerdrnd74,

  Is not not be able to access you iPad because it is disabled does not for a good hour.

  If you have forgotten the password for your iPad, iPhone or iPod touch, or your device is disabled through the steps you need to do to get the iPad upward and running. I did these steps a few times before and they work every time. You may need to put your device in recovery mode, more than once if your internet speed is slower by downloading the restore software.

  See you soon

• Try to get the split screen set up.

  Is there a way I can get the screen on my computer with windows 7? Two different applications going at the same time?

  Hi SuzyQ87,

  I'm not sure I quite understand your request...

  Assuming that you do not want to have two windows application tiled on your screen, so that each occupies half of the screen, one on the left and one on the right, you can use the new feature in Windows 7 Aero Snap (Docking).

  1. open the first application.

  2. to ensure that it is not maximized.  It is considered to be maximized if the application takes up the entire screen and you can't see any part of the office.  If it IS a maximized, click the Center button (square, blue highlight) in the upper right window of the application.  It will grow smaller and you will be able to see the desktop around it.

  3. now, move your mouse to the top of the window title bar, click the mouse and drag the window to the left edge of the screen.  Keep, drag until the mouse reaches the edge and see you the outline of the window to jump to the center of the screen.  Let the mouse upwards.  The application will now sized to fill in only half of the screen.

  4. Repeat steps 1 and 2 with the second request.

  5 drag, as in step 3, but this time to the right of the screen.

  Voila, two windows tiled side by side on your screen.  You can drag the edge again and they return to their original shape and their size.

  FYI, the Aero Snap setting must be enabled (which is the default) so that the above to work:

  http://www.Winhelponline.com/blog/enable-and-disable-Aero-snap-Docking-Windows-7/

  -Christmas

• How do you get the functionality of firefox when you page the entire screen

  I was on a firefox page and fool the screen full page. Now, I can't the configuration of firefox in the upper left corner of the screen to print, layout. How to restore firefox on the screen

  If you are in full screen view then hover over with the mouse upward to make the bar appear Navigation and tab bar.
  
  You can click the maximize button in the upper right to leave the mode full screen or empty space of a right-click on a toolbar and use "exit full screen" or press F11.

  Press F10, or press the Alt key to bring up the 'Menu Bar' temporarily if the menu bar is hidden.

• Satellite L500 - scrolling the mouse does not work

  I can't get the mouse wheel to scroll in any application using an external mouse - touchpad scrolls ok.

  I tried several different mice. The wheel button brings up a display of all the programs that I have open (Windows 7), but the wheel does nothing. I am currently using a Microsoft wireless mouse, but I tried it with wired mice as well. Nothing seems to work.

  Thank you

  Which is really strange.
  You might have installed some application that you got with this Microsoft mouse?

  I have two laptop computers and peripheral two external. One is Logitech and the other some cheap without mouse name and both have been recognized correctly suite preinstalled Win7.

• Clicks of the mouse will not work on the browser - suggestions?

  Following an update of Firefox last year, I can't get the mouse clicks to work on the browser. Is not serious if he left or right buttons. Links and radio buttons get highlighted when you move the mouse over the links or buttons, but they do not work when you click on it. They work on other browsers (Explorer and Chrome) but is no longer on Firefox. I use it on a Sony Vaio laptop running Windows 7

  The reset Firefox feature can solve a lot of problems in restaurant Firefox to its factory default condition while saving your vital information.
  Note: This will make you lose all the Extensions, open Web sites and preferences.

  To reset Firefox, perform the following steps:

  1. Go to Firefox > help > troubleshooting information.
  2. Click on the button 'Reset Firefox'.
  3. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
  4. Firefox opens with all the default settings applied.

  Information can be found in the article Firefox Refresh - reset the settings and Add-ons .

  This solve your problems? Please report to us!

• Firefox does not not at the mouse entry properly. Bug?

  Random frequent time Firefox 10 will cease to respond to mouse clicks.

  I can't click inside the fields on the page, also the address bar and the search bar of FF do not respond. When I move my mouse over them, the point of the mouse 'Text' appears, but when I click on the input box is not active the icon thing flashing text. If I double click on the address bar, it does not select the current url, as it normally would.

  Video controls flash are not able to click. The play/pause button cannot be clicked. The volume cannot adjust. Full screen cannot me input or output (if the mode full screen is enabled before entry-stop mouse works).

  To get the mouse entry at work, so that I can type in the text boxes, or use the controls in the flash player, I have to click outside of Firefox. Which means that I have to click on the Windows taskbar, or switch to another program.

  I tried to get a screen recording of this question, but every time that I turn my entry fields/flash video recording software before reagent. Assuming that this is because the recording software becomes active on Firefox. And as I have indicated above to switch to another program, and then back to Firefox allows fields/cards entry videos work again.

  I thought that this could be a problem of Mouse/touchpad; I reinstalled my Wireless Mouse Software, tried a USB mouse and reinstalled my Touchpad software, but nothing seems to fix the problem.

  I also experienced this "bug".

  Report bug that cor - el related you ( Bug: 718939 ) you will find a link to a version Patched in Firefox 10

  • The Version connected (located in the comment 40)
    • Note that this is not a version of Microsoft Office.

  The task has worked for me and solved the problem. Unaware of when an official challenge will be available

• The mouse pointer behaves erratically

  Original title: the mouse pointer

  FOR SOME TIME MY MOUSE POINTER STARTS GOING BONKERS, BEGINS TO BLINK. SOMEONE CAN ME SAY WHY? PLEASE... NORMA JEAN THOMPSON

  Hi Norma Jean.

  Welcome to the Microsoft community where you can find all the answers related to Windows. I'll definitely try and help you get the mouse to work, however if the problem is with the device, you may have to contact the hardware manufacturer.

  Could you also give us some more information?

  1. have you installed the drivers for the mouse?

  2. you have any antivirus installed on the computer program?

  3. What is the brand and model of the printer?

  4. are you aware of any recent software or hardware on the computer changes?

  You can change the setting of the mouse and check if it helps.

  Although article apply to Microsoft hardware, you can also go through the Manual steps in and check if it helps.

  Hope this information was helpful and let us know if you need help in the future about Windows. We will be happy to help you.

• KVM does not work with the mouse

  I recently bought a pink switch KVM 4 port. I bought a microsoft keyboard and wireless mouse.
  I also bought a mouse 3000 and 4000 mouse. I have a pink usb to ps2 tranalator to the KVM.
  The keyboard and mouse 3000 work great togeather, but I can't get the mouse working through
  the KVM. It works fine connected directly to the Port USB, but not the KVM port.
  Ralph

  Hello Ralphv,

  Thank you for your message.  Because this problem exists only with the KVM (mouse and keyboard are functional, but are not with the KVM) it would be best to contact the KVM manufacturer for assistance.  You can try a different mouse or keyboard to test functionality.  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• What do I do if the mouse suddenly abandoned its work

  Hello

  It happenend two times already: my mouse no longer works and I do not know how to save the program, nor how to shut down the computer safely. Is there a key combination to help me.
  It normally happens in the middle of something, especially nights and no battery on hand. So, what can I do?
  I'm working on windows vista.
  Thank you
  Petra

  1. I also use a wireless mouse.
  Usually changing battery new wil get the mouse going again. You should not do something else.
  If you need to, and I don't see why it is necessary, press the Power button to turn off the computer.

  2 invest a mouse "connected". In this way, when you're out of battery for the wireless mouse, simply plug the wired mouse.