GNS3 3745 - no switch connectivity

Hi all

use GNS3, and than switch 16port module. I created an instance of PC and connection to f/0/0, which is a port of layer 3, I can connect through Layer 3 IPs. Then, I reconfigured and connected to the instance of PC through a layer 2 port f2/0 which is part of the switch 16port module. The 16 ports are by default in the vlan 1. I have assigned an IP address of 10.1.9.1/24 to the VLAN and gave the PC 10.1.9.2/24. I can't ping and I can not even ping 10.1.9.1, VLAN 1 IP. Did I miss something? Thank you.

Mark Sargent

Router #sh worm

Cisco IOS Software, software 3700 (C3745-SPSERVICESK9-M), Version 12.4 (19), RELEASE SOFTWARE (fc1)

Router #ping 10.1.9.1

Type to abort escape sequence.

Send 5, echoes ICMP 100 bytes to 10.1.9.1, time-out is 2 seconds:

.....

Success rate is 0% (0/5)

Router #sh arp

Protocol of age (min) address Addr Type Interface equipment

Internet 10.1.9.1 - c402.2668.0000 ARPA Vlan1

Router #sh ip int br

Interface IP-Address OK? Method State Protocol

FastEthernet0/0 unassigned YES manual up up

Serial0/0 YES no not defined administratively down down

FastEthernet0/1 no YES not defined administratively down down

Serial0/1 no YES not defined administratively down down

FastEthernet2/0 not assigned YES unset up towards the bottom

FastEthernet2/1 no YES undefined upward to the bottom

FastEthernet2/2 no YES undefined upward to the bottom

FastEthernet2/3 no YES undefined upward to the bottom

FastEthernet2/4 no YES undefined upward to the bottom

FastEthernet2/5 no YES undefined upward to the bottom

FastEthernet2/6 no YES undefined upward to the bottom

FastEthernet2/7 no YES undefined upward to the bottom

FastEthernet2/8 YES no not set up down

FastEthernet2/9 no YES undefined upward to the bottom

FastEthernet2/10 YES no undefined up down

FastEthernet2/11 no undefined upward down YES

FastEthernet2/12 no YES undefined upward to the bottom

FastEthernet2/13 no undefined upward down YES

FastEthernet2/14 no undefined upward down YES

FastEthernet2/15 no YES undefined upward to the bottom

Vlan1 10.1.9.1 YES manual downwards upwards

Router #sh int f2/0 switchport

Name: Fa2/0

Switchport: enabled

Administrative mode: static

Operational mode: down

Encapsulation of administrative circuits: dot1q

Negotiating Trunking: disabled

The VIRTUAL LAN access mode: (default) 1

Native mode VLAN Trunking: 1 (default)

VLAN Trunking enabled: ALL

Assets of VLAN Trunking: no

Priority for unmarked frames: 0

Override the priority tag vlan: FALSE

The voice of VLAN: no

The unit trust: no

Ports of status for the name of VLAN

---- -------------------------------- --------- -------------------------------

1 active default 0/Fa2 Fa2/1, Fa2/2 Fa2/3

FA2/4 Fa2/5, 6/Fa2 Fa2/7

FA2/8, 9/Fa2, Fa2/10, Fa2/11

FA2/12 Fa2/13, 14/Fa2 Fa2/15

active by default fddi 1002

assets of token-ring-default 1003

1004 fddinet - default active

1005 trnet - default active

Network type VLAN SAID MTU Parent RingNo BridgeNo Men BrdgMode Trans1 Trans2

---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------

1 100001 1500 enet - 1002 1003

1002 101002 1500 fddi - 1 1003

1003 b 1005 1500 101003 0-1 1002 srb

1004 etnbdf 1500 101004 - 1 ibm - 0 0

1005 trnet 101005 1500 - 1 ibm - 0 0

Router #sh int vlan 1

Vlan1 is up, line protocol is down

Material is EtherSVI, the address is c402.2668.0000 (bia c402.2668.0000)

The Internet address is 10.1.9.1/24

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Type of the ARP: ARPA, ARP Timeout 04:00

Last entry, never, never hang output

Final cleaning of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 0

Strategy of queues: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bps, 0 packets/s

5 minute output rate 0 bps, 0 packets/s

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 Runts, 0 Giants 0 shifters

entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored

12 bags of output, 890 bytes, 0 underruns

output 0 error, 1 interface resets

unknown protocol 0 drops

output buffer, the output buffers 0 permuted 0 failures

you need to change cable

share this i must configure the interface in this way:

int fa2/0

SW mo VAC

SW acc vla 1

SH

only HS

end

!

WR

!

Take care

Alessio

Tags: Cisco Network

Similar Questions

  • Switch Connectivity

    Hey Cisco experts!

    I have a small question, I'm sure you can answer for me. I have installation of the Israeli army for the clients that I questioned how they are physically connected. Connection to the MDF is ok because they use their ports of 10 GB on fiber optics. The question I have is if there are multiple switches in the Israeli army should they be connected to each other using their 10 GB ports from A to B and C and then also to connecting A to C on switch ports? I think it's can cause a loop but wanted expert advice.

    Thank you

    Hello

    Yes, when you have multiple MDF switches, connect together to provide redundancy of the network.  Of course if you connect to layer-2 switches together, you must run stp or use some other technologies like stack to make it look all MDF has a switch.  There are also VSS for the 6500 that offer the same advantages as the stacking on the 3750 series.  In this way, your don't have to use STP.

    HTH

  • What configuration of VLAN requires a switch connectivity defined as an access port?

    What configuration of VLAN requires a switch connectivity defined as an access port?

    By external switch tagging

  • 2748 switch connection problem

    Have this question about 2748 mode managed connection, I just bought. 2008-05-19

    After the initial 'admin' connection unit by default, the page of ' restore saved Configuration.  I can't go past this page to enter my network settings. Only the button on the screen 'apply' just switch re boots.
    Saw this same question on another Board unanswered, have winXP & 2000 machines will by default 192.168.2.1
    Have other 2724 switches that work very well.
    Thank you

  • Switch connection SG300 ESW 540

    I have a problem connecting my ESW 540 to new supplementary switch Csico SG300. Is the uplink port must be configured differently?

    The port of the ESW becomes inactive when I connected to the port of SG 300.

    Thank you.

    Untung,

    Specify the switch or disable SmartPort role on the port.

    -Marty

  • Location of switch connected upstream

    Hello world

    I inherited a custome with a bunch of SG300 in their LAN room and out in the warehouse.

    I need to configure a VLAN and genius that made me not label what room LAN switch plugs into the unit from the warehouse. Is there a tool/method that I can use to find who pass and the port of this warehouse switch is associated to?

    Thanks in advance.

    Hi David, if the switch is on a relatively new firmware (everything except 1.0.0.27) then you can use CDP to find the directly connected switches.

    If theyre on the original firmware, you have to use the mac address table.

    -Tom
    Please mark replied messages useful

  • Cisco SG 300-20 switch connects to the router

    Hello

    I try to install my new switch Cisco SG300-20 in my local network, but I'm not succeed.

    The SG 300-20 fails to connect to my router.

    When the router is directly connected to the SG 300-20 I fails to obtain the DHCP configuration. Any port I try fails.

    When I add a former switch between the router and the SG 300-20, SG 300 - 20 manages to get the DHCP configuration.

    When I use a static IP on the SG 300-20 and the router is directly connected, it is not an operational bridge in the IPv4 configuration.

    Where I'm looking for a solution?

    The SG 300-20 is maybe defective and I would stay there?

    A. van Egmond

    A few things you can check are:

    See if the system is blinking. If it is the default ip address. If it is solid the IP address has changed due to a static assignment or DHCP.

    If no link light is on or the system flashes, the reason why could not tear out DHCP is due to a shift of port negotiation. Try setting the port on the router or the full 100 MB switch or what ever you like just to see if that helps.

    Make sure that you are also on the latest firmware.

    Try factory default of the switch with the button of reset for 45 seconds.

    Cisco Small Business Support Center

    Randy Manthey

    CCNA, CCNA - security

  • How to use a switch connected to the DAQ card as a source of events in a Structure of the event

    Is easy using a switch on the front panel as a source of events. However, I like to use an external switch electrician on my card for the acquisition of data (NI PCI-6229) as the event source in the Structure of the event. Can anyone help?

    Happy New year to you too!

    Attached is an example in BT 8.5

    • It uses the time-out loop (running every 100ms) to simulate your reading of the data acquisition card.
    • A shift register is used to keep track of the previous value of the switch.
    • When a change of the switch is detected, the user event is raised and the display will show the new State.

    Running the vi with activated highlight performance can be useful.

    Steve

  • two 6220 switches connected to the towing and storage Equalogic servers

    any suggestion for the discrepancy between the switches of towing configuration

    For redundancy of the switch, you would stack the switches. See page 59 of the guide: http://dell.to/1MVFCsU , he will learn more about the feature and set it up between the two switches.

  • WebLogic 9.2 switching connection pool

    We use a Weblogic 9.2 application server. Now, we have an obligation to change the server database at a point in time because some process on the day of the day in a database. Is it possible to switch from one database to another without having to restart the server? I tried to use MultiDataSource, but it only works if one of the database is down... so I can't use it because the two database servers are in Active mode at this time...

    MultiPools should be thin. The pool you want to first, used in addition to the time list
    and the second a secondary. A failover MULTIPOOL won't see the second
    the first pool is unusable. You can make unusable during the execution of the
    by disabling script from console or admins at any time, and you can turn it back on
    later in any time you want, and the MultiPool will immediately start using it
    Once again.
    Joe

  • DV7 3105ea:touch controls such as volume control, turning power switch connection Wi - Fi stopped working

    My laptop is dv7-3105ea. The buttons above the keyboard touch and just below the screen has stopped working. Could someone please? Thank you.

    Try a hard reset, works sometimes. Disconnect all external devices first.

    battery and power cord 1 / removal

    2 - Press the power button for 30 seconds

    3 reinstall only the power cord for the first start.

    4. turn on

  • OK to mix 'of connection to the switch"and"close relay switch?

    Hi all

    I'm developing a test sequence using the card multiplexer 2527 to the track signals.  To configure the card, I use DAQmx switch functions.  In my application, I have a Subvi routine that imports the data from a spreadsheet Setup and run a loop for to set the configuration for each step (each iteration of the loop contains the channel for 2527 card information).  The topology is set on the first iteration, as well as the configuration of the path to the first string.

    My concern is this: I need to close the extra channels/relays without changing the topology or resetting the device.  In the first round, I use "connection to the switch" function to set the initial path, (ch0 to com0 for example).  Then in subsequent iterations of the loop, I use "Relay close switch" function to close the additional channels individually (for example k2).  In the end, when the measure is taken, both ch0 ch2 must be closed and routed to com0.  This implementation is so sure, or am I somehow to make the adjustments to the initial loop?

    I would like to test this with the hardware, but it is not yet available.

    Also, I realize that I could use independent topology and configure all relays individually for each step, but I hope that my approach will be easier and safer.

    Please notify.  Thank you.

    GSinMN

    Hello GSinMN,

    It's OK to mix 'of connection to the switch"and"Close relay switch"If you understand what's happening below. "Switch Connect" connects two channels by closing a path of relay between the channels, then "Close relay switch" can be used to change the State of the individual relays. If you are not careful you can mess up your connection by activating / deactivating relays that are part of the route connecting your channels.

    "Also, I realize that I could use independent topology and configure all relays individually for each step, but I hope that my approach will be easier and safer."

    I would recommend the topology independent if you want to stick with connections to channels only. http://zone.NI.com/reference/en-XX/help/375472G-01/switch/2527_independent/

    Initial connection:

    CH0-> pcom0

    pcom0plus-> icom0plus

    pcom0minus-> icom0minus

    icom0-> com0

    In each future iteration just connect to the next to pcom0 channel (which will be indirectly connect it to com0):

    CH1-> pcom0

    CH2-> pcom0

    ...

    ...

    Jarrod

  • a switch that is part of the battery will charge if it loses connectivity to the master?

    If I have 4 switches configured as a stack - where the StackWise ports are connected within 1 to 2, 2 to 3, 3 to 4 and 4-1. Switch1 is the master.

    If something were to break stack connectivity between 4 to 1 battery still works as switch 4 still has connectivity to control through 3 to 2 to 1.

    Below the output of reference-

    switch #show switch retail
    Switch/battery Mac address: 0023.34b3.5600
    Current H/W
    Switch # Mac address priority Version State role
    ----------------------------------------------------------
    * 1 master 0023.34b3.5600 15 0 loan
    0023.0543.aa00 member 2 14 0 loan
    3037.a6ca.2000 member 3 13 0 loan
    3037.a6ca.6900 Member 4 12 0 loan

    Battery nearby Status port
    # 1 Port 2 Port 1 Port 2 Port switch
    --------------------------------------------------------
    1 low ok 2 none
    2 ok Ok 3 1
    3 ok Ok 4 2
    4 bottom Ok No 3

    switch #.

    With this as the current state 2 reload automatically cause the 3 and 4 to charge because they lose connectivity to control completely or they will stay up as of the individual switches

    And same question again - switch 3 cause reloading will rise 4 to recharge automatically as he lost connectivity to control completely?

    I've seen this happen... so need to confirm if what is expected or we must check and solve another question that might have caused this!

    This is not the expected behavior. A member of the battery is disconnected does not cause other switches to restart. They work as individual switches.

    Cisco documentation:

    An active switch connected to a fully operational
    stack becomes member of the stack. It receives the functioning
    setting up the master of battery
    . When you disconnect a battery Member
    Uh, numbers and port switch
    numbers of the remaining members of the battery
    no change and the switches do not recharge.

    http://www.Cisco.com/c/en/us/TD/docs/switches/LAN/catalyst3750/software/...

  • How to connect switch processor on 6500?

    Here is the release of version see the:

    Cisco Internetwork Operating System software

    IOS (TM) software to MSFC3 (C6MSFC3-PSV-M), Version 12.2 (17 a) SX1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

    TAC support: http://www.cisco.com/tac

    Copyright (c) 1986-2003 by cisco Systems, Inc.

    Updated Thursday 29 October 03 03:57 by next

    Image text-base: 0x40008FBC database: 0x41E94000

    ROM: System Bootstrap, Version 12.2 (17r) S2, RELEASE SOFTWARE (fc1)

    XXXXX availability is 16 weeks, 4 days, 5 hours, 25 minutes

    System returned to ROM by unknown charge cause - suspect boot_data [BOOT_COUNT] 0 x 0, BOOT_COUNT 0, BOOTDATA 19

    System restarted at 10:23:42 GMT Monday, August 26, 2013

    System image file is "bootflash:c6msfc3 - psv - mz.122 - .SX1 .bin 17A"

    Cisco ( MSFC3 (R7000) processor with 458752 K / 65536 K bytes of memory.

    Card processor ID XXX

    SR71000 pace at 600 Mhz, implemented 0 x 504, Rev 1.2, 512 KB of L2 Cache

    Last reset of tension

    X.25 software Version 3.0.0.

    Connection software.

    15 virtual Ethernet/IEEE 802.3 interfaces

    512 KB of non-volatile configuration memory.

    8192K bytes of packet buffer.

    65536 K bytes of Flash internal SIMM (sector size of 512K).

    Configuration register is 0 x 2102

    ********************************************************************************************************

    I tried to connect to MS by issuing the command "login remote swtich", but this command is not recognized:

    Switch connection host #remote name

    ^

    Invalid entry % detected at ' ^' marker.

    #remote host name?

    % Unrecognized command

    How can I see the modules of the line connected to this switch and how to connect the switch processor?

    Hello

    Your switch runs hybrid, which means it runs CatOS on the SP and IOS on the RP.  You are connected to the RP to be able to use the hybrid you must first connect to the SP and then you can get the PR by issuing the command-session 15 that will register you in the RP that takes place in IOS. To return to the SP just type "exit" and it drops you to MS.

    Hope this helps. !

  • HP Pavilion dv7 Notebook PC P: erratic connection

    Recently, after booting, my wireless connection is cut. When I look at the wireless assistant, I see 3 options fo switched connections listed above the wireless option. I canthen manually connect to the wireless option. How to restore wireless automatically when starting upwards?

    Hi!, HenryTST:

    I have Windows 7 Home Premium, 64-bit installed in my AIO HP PC 120 1026 has, with TP-LINK Router 2.4 Ghz.

    My suggestion is that change the channel in the router (1/11). Many times if you have proxy routers, have interference and produce of crack.

    Try, for verification, download acrylic Wi-Fi home, of... https://www.acrylicwifi.com/en/WLAN-software/WLAN-scanner-acrylic-WiFi-free/

Maybe you are looking for

  • Strange desktop file authorization behaviors?

    Elements copied from office ask for password to move or delete. Usually the items copied from a rom drive or dvd/cd external? Just right on the desktop.

  • Satellite Pro L10 - I can't install Win XP - PXE - E61:Media test failure

    Hello I was wondering if any1 can help just bought a 2nd hand toshiba satellite computer laptop pro L10Model - PSL15E-00L0179I It has been wiped and when I charged it up it has developed in DOS, but won't let you enter any command all it says is -. P

  • Satellite Pro M30 descending without warning

    Hello My old one year Toshiba Satellite Pro with a card his Sigma such C - Major DIES many times when I start a good intensive application, such as Sound Forge, or Windows Media Player or a game like GTA Vice City or Return to Castle Wolfenstein and

  • X 1 power buttom problem

    recently, I found that my power button failed. It has happened since the last replacement of the motherboard and the battery to the 03/01/2012.  I took my computer to the 16/02/2012 service center and they said that it is the connection of the cable.

  • How can I get rid of a divided e-mail screen and return to the full e-mail to read mail?

    How can I restore screen to full screen to read my emails?  It's now a screen divided into two!  Also, when sending an outgoing e-mail it warns me "pop error 3" & tells me letters 'no.'      What does that mean???   Pleeeeazzzzzzze help! ??