grinding noise when my HP LaserJet Pro 400 color MFP M475 calibrates

When my color HP LaserJet Pro 400 MFP M475 recalibrates, I get a grinding or gear sliding noise.  No idea how to fix it or what to look for?

Noise problems are difficult to troubleshoot remotely and they could easily mislead even when we are near the unit.

Please confirm if the noise is a squeak or a noise squeky/hum.

As you mentioned that this happens only during calibration, it is why I suggest you to double check & validate your toner cartridges.  Among the toner cartrdige is maybe defective and causing this problem.

If not the toner cartridge, then it would be one of the components of hardware printer that is at issue, where a Tech HP may need to perform a physical inspection of the aircraft and the error condition.

Tags: HP Printers

Similar Questions

  • HP LaserJet Pro 400 color MFP M475 - driver Linux

    According to the product description page, this printer is supposed to have a Linux driver available, but I can't locate one.

    Nobody knows where and when you can be available for download?

    Thanks in advance.

    HP LaserJet 400 colorMFP M475dn NPIE7A8DA

    OS: Linux (any flavor)

    I think that this is the site you need to get the information you're looking for:

    HP Linux imaging and printing

    Supported printers

    MFP color HP LaserJet 400 m475dw

  • turn off the broadcast without wire - HP laserjet pro 400 color mfp m475dw

    How do I disable broadcasting SSID for HP laserjet pro 400 color mfp m475dw.  I disabled the configuration via the web console wireless printer, but it is still broadcasting.  I also updated the firmware to 20131028 last available.

    Since it is wiered one of the scenario, I could solve this with the help of the HP Support is by doing factory reset/NVRAM reset the unit by turning the printer and holding right arrow and cancel on the touch screen of the device (cancel is on the lower right of the touch screen on the black area and right arrow is just above him (one in the middle of the Panel) in the same black box) and the device of turning on until the message something like storage reset... is displayed and can release the two buttons/zone button.

  • I get a pcl xl error message when we print our LaserJet Pro 400 Color MFP

    When I scan or fax, we get:

    PCL XL Error

    Subsystem: TEXT

    Error: InternalError 0 x 50

    File name: cheettext.c

    Line number: 710

    The printer is a Pro 400 Color MFP LaserJet - m475dw

    Windows 7 Professional Service pack 1

    What should I do to fix this?

    Thanks for the help.  I actually did an update of the firmware and it solved the problem.

  • the white pages when printing for laserjet pro 200 color MFP M276nw

    When printing to my color Laserjet pro 200 M276nw MFP, the pages are all empty.  I tried to put off the printer and tried to have disconnected and reconnected.  That did not help.  The pages are still blank.  Any suggestions?

    You are unable to print the 'print quality Page' of the façade or do not know how?

  • HP Laserjet pro 400 color MFP M475dn

    Hello

    I use my all in one printer including Telec.

    Fax works fine but what is possible when an incoming fax can print on tray 2?

    When a fax is coming, the fax is now taken paper from Tray 1.

    Thank you

    Mathieu

    OK... found out some information that should solve your problem:

    You will need to access your integrated webserver (EWS) > locate the IP address of the printer > what enter in a web browser > access the built-in Web server.

    Go to the System tab > installation paper > keep your the same default settings > change your settings from Tray 1 to the letter, any size. Keep the tray 2 settings > any size, any size. Save the settings.

    By substituting the default settings, this should change where your paper fires.

    Let me know how it works... good luck.

  • HP LaserJet Pro 400 color MFP TOUCH SCREEN M475dn

    Touch screen Frozen-Unable to fax, scan

    Hi Pattie,

    I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a commercial product. You can do so at http://h30499.www3.hp.com/hpeb/

    I hope this helps, have a nice day!

  • Help! My M475dn MFP HP LaserJet Pro 400 color printer will NOT print!

    HP LaserJet Pro 400 color MFP-M475dn-CE863A

    Printer on a network and can connect to multiple computers that include: Mac OS X, Windows 7 and Windows XP.

    When I try to print from my iMac, the print queue of the printer says "the printer is not connected.  When we try to print from Windows computers, it is in the right queue and does not print.  When I go the printer itself and try to print a page of demonstration or page supplies directly to him, it says on the screen which is printed, but nothing happens.  This is not hum or anything!  The port where the network cable is connected is switched on green that says HP which means that the network cable is connected.  We've had this printer for a year now, and something like that never happened.

    I did not have any software or anything like that until this happened.  It was working fine on Saturday when we used it, but when we arrived at work today, he just decided that it would interrupt printing!

    I'm puzzled!  I tried 'ping' IP address of the printer from my iMac and it pings fine.  Does anyone have advice?

    (I tried to make of the obvious like too switch the printer on and off and shutting the computer down and nothing!)

    Okay, so I feel a bit stupid right now.  I decided that I would be closed the printer for about an hour to see if it was there, and what you know-it has been!  I had to turn it off several times before but I guess it wasn't long enough.  What a pain!

    Thanks to everyone who took the time to read this!  Sorry to waste time everyone!

  • laserJet Pro 400 color: printer

    Hello Mr President
    I want a help on your part I have a Color LaserJet Pro 400 m475dw MFP
    and when I turned it on. I show masseage like this {10.1002 electric memory error}
    How can I solve this problem, Mr President

    Hello Sir,

    The error that you expose is a problem with one of the toners.
    The magenta to be precise.

    In this case, the recommended action is to replace the magenta toner with an original RESUME.

    Kind regards

  • Unable to connect to the HP ePRINT with Color LaserJet Pro 400 M475dw MFP website

    LaserJet Pro 400 color multifunction m475dw-Just installed. Print, scan, copy and fax all works fine! use of WiFi

    Using IMAC OS 10.8.2 with all updates

    Netgear DGN2200v3 router using

    Printer not connect to the HP ePrint website

    Printer connects using Hp and profile for fax set up etc.  But the "HP Web Services" article when enrecorded and hit the Activate button - it does not connect to the site - it seems just to refresh.

    "If I try to connect thro the printer not the imac and try to activate the web services, it says" connection "on the screen BUT after a few minutes of trying - so says" CONNECTION ERROR - the printer is unable to connect to the service. Check the internet connection

    ANY IDEAS - HAVE I MISSED SOMETHING?

    Thank you very much

    I try to pull up the built-in web server (EWS) by entering the IP address of the printer in a browser and set a static IP & DNS address.

    The information for the default gateway, subnet mask and IP address can be accessed from the Setup menu on the front panel, go to settings > reports > network summary and it will print off the coast.

    Once you entered the IP address in a browser and have the EWS pulled up, go to the tab above titled "Networking". Then click on IPv4 in the left column; who will bring to the top of the address configuration page.  Place the manual radio button and fill in the IP address, the default gateway and the subnet mask with the information from the report. You don't fill the part entitled WINS server, which can be left alone.

    You will then want to fill in the DNS of the page part, the favorite should be set to 8.8.8.8 and the alternative/secondary must be set to 8.8.4.4. Then click 'apply '.

    Power cycle the printer. Turn off the power, wait 30 seconds and then turn it back on. Once it is fully operational, try again to connect to web services.

  • HP Laserjet Pro 200 Color MFP FAX answering machine vs M276nw

    We have the following MFP: HP Laserjet Pro 200 Color MFP M276nw

    Our office has a phone line to be shared between the phone and FAX (M276nw). The phone is a phone single line of integrated with a digital answering machine Panasonic KX-TG7531 model. I can't seem to find the right combination of settings for ringtone for the phone and the FAX that allows callers to leave a voicemail without the FAX modem tones interfere when the caller leaves a voice message. It's as if the fax does not recognize that the answering machine picked up and he continues to make sounds of modem. The tones are saved as well as the message of the caller's voice, which makes the message difficult to understand. In most cases, the caller simply hangs up without leaving a message (we've heard talk about this later).

    Please tell us how to implement. Thank you!

    Furthermore, the HP Laserjet Pro 200 Color MFP M276nw replaced a MFP from brother, but the Brother FAX has worked with the same phone from Panasonic.

    Hi crmarrio

    I understand that you are having problems of fax.

    Run this test for the fax.
    In the home screen, press the button on the key.
    Tap the service button.
    Tap the fax service.
    Touch run fax test.

    Check all these fax settings.

    Here is a url for the fax troubleshooting.

    http://support.HP.com/us-en/document/c03363598

    Go to the icon/fax setup menu/Advanced Configuration key / private receive/disable it.
    Go to thewrench icon/service/fax service/error correction/stop.

    Go to Settings icon/fax thewrench / fax/advanced/change configuration to speed it to the middle.

    Go to the key icon/fax installation base/menu Configuration/response/game of rings rings.

    (if using an answering machine-more rings on fax and answering machine or rings of mail without a voice for the fax, but receives no voicemail, should get installation of distinctive ring on the line in this case)

    Go to the key icon/fax setup basic menu setup/response/selection of auto mode.

    Go for a key icon/service menu/fax service/clear saved faxes

    Go to key icon/fax installation base/menu setup/distinctive ring/set for proper ringtone type. (if you don't have a special ringtone set on all ringtones.

    Update the firmware of the printer by usb connection.

    http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&docName=c03363598&LC=en&product=5097654&

    Let me know the results of the fax test, and if you were able to send or receive a fax.

    If you're still having problems, let me know and I send you private message how to reset the printer.

  • Multifunction color HP LaserJet Pro 200: HP LaserJet Pro 200 color MFP M276nw on El Capitan: Scan does not

    Since my upgrade to El Capitan my USB connected HP LaserJet Pro 200 M276nw MFP color analysis no more.

    What I've tried so far:

    Installed the latest drivers > unsuccessfully

    Tried all the solutions suggested here: http://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/HP-LaserJet-Pro-200-color-MFP-M276nw-Scanni... > no success

    Have any suggestions what to do next?

    Update: the solution provided in this thread solved my problems:

    http://h30434.www3.HP.com/T5/Mac-printing-and-scanning/HP-LaserJet-2300-not-working-with-El-Capitan/m-p/5281267/highlight/true#M61077

     
  • Urgent: HP LaserJet Pro 200 Color MFP M276

    Heeeeeeeelp! Urgent!

    I am looking for the software and driver for HP LaserJet Pro 200 Color MFP M276.

    To the HP Web site, there is no download available.

    Who can help me with a link downlod?

    [Personal information]

    Hello

    Download the software on the HP site is fully accessible, I downloaded it without any problem at all right now.

    The following lik select your operating system and click on send, and then click Download for the full feature software and drivers:

    http://support.HP.com/us-en/product/HP-LaserJet-200-color-multifunction-printer/5097648/model/5097653/drivers

    If you have problems please specify what operating system you are using.

    Shlomi

  • HP LaserJet Pro 200 Color MFP: HP LaserJet Pro 200 Color MFP M276n: low memory

    Hello

    my new M276n printer has memory problems. Printing over two pages are stopped with a notification of "memory". I searched this forum and found a 'temporary' solution (reset printer to default settings) and a stage of 3 mysteriously missing (deleted the message). This does not in the long run because after only 4 more printing, I have the same problem again. I don't print many, mainly Amazon returns labels and information. Reset or not, the information page shows 127MO 256 MB available memory. What is the other half serving?

    Issues related to the:

    1. is there a solution?

    2 can it help if I disable unnecessary features (fax)?

    3. can I disable fax? (If Yes: how?)

    4. is there a solution?

    Thank you!

    Restore the default settings is not usually serve the memory of a printer.  You need a cold reboot to complete this procedure.

    Cold Reset as follows:

    http://h30434.www3.HP.com/T5/printing-issues-troubleshooting/HP-LaserJet-Pro-200-color-MFP-M276nw-cold-reset/TD-p/5060955

    The video at the bottom of the first page is very useful.

  • The HP Laserjet Pro 100 Color MFP 175nw scanning

    Does anyone know if HP Laserjet Pro 100 Color MFP 175nw requires the Ethernet connection to scan documents or WiFi will be sufficient?

    Hello

    The product of its capacity to provide by any method of connection took in charge.

    So you can scan via USB, Ethernet or wireless connection.

    Concerning

    Shlomi

Maybe you are looking for

  • Installing XP on Tecra S5 - Intel Matrix Storage Manager

    HelloIm trying to install XP on a Tecra S5.As described in the manual, I have created a disk with Intel Matrix Storage Manager.With a floppydrive USB I tried to install XP with the F6 method.I could choose the suitable from the disk driver and was ab

  • Flow of HT 7-5709 - Boot/startup problems

    I just bought the HP Jet 7 tablet.  The first time I turned on the Tablet, I saw the HP logo for a few seconds and the device off.  The dots has not yet come full circle.  I thought it might be a power problem, so I plugged it and saw the charging sy

  • Drawing on the viewfinder

    Hi guys,. Very general question: is it possible to draw something or place an image on the camera viewfinder preview without going through the part of the image in the viewfinder coverage? For example, I want to put a dot.png on the screen, but have

  • The only vector of Adobe Stock purchase

    HelloI tried to buy one vector of the stock of adobe, but when you click on buy one image, I just got the following message.When you clikc ok. He just puts you in the same 3 purchase options and you continue along in this loop.  Can anyone help pleas

  • Deployment of EGGS - Error Message

    HelloThis is my first post, so please bear with me...I am trying to deploy a. OVA for VM Workspace 1.8 but I get an error that reads"The OVF package requires the vApps with several VMS support. Details: line 14: element not in charge 'virtualSystemCo