Grouping of NETWORK issue cards *.

Similar Questions

• Grouping of NETWORK cards causing the ESXi to retransmit ethernet frames received.

  I had an HP Proliant DL380 G5 ESXi 5.1.0 connected to a Cisco 3750 Switch stack.

  All by performing a tcpdump on a host without a report, I discovered that he was under the bombardment with ethernet frames for the MAC address of a computer virtual located on a host across the data center. After a few brief troubleshooting, I discovered that I was able to stop those erroneous frames by disabling NETWORK adapters on my VMWare host group.
  
  I believe that in my situation when ESXi is configured to use two network cards to all frames received on vmnic0 and retransmits them on vmnic1 and vice-vesa. I experienced these symptoms when ESXi is configured for failover with an active adapter and adapter mode standby and I also experienced the same symptoms in the following load balancing configuration.
  

  
  

  Symptoms: some time after activating the load balancing, all frames Ethernet for the MAC address of a virtual computer on the affected host are broadcast on each switch port in the entire data center.
  
  Steps to reproduce:
  (1) implementation below configuration.
  (2) unplug the ethernet cable connecting vmnic1 and switch1 port gi2/0/4
  (3) run the host 1.1.1.1 EI - n - q tcpdump on any machine physics linux in the data center (don't even have to be connected directly to 1).
  Confirm there is no packet seen with the IP address of 1.1.1.1 destination
  (4) plug the cable between vmnic1 and switch1 gi2/0/4 port ethernet
  (5) wait 60 to 120 seconds
  (6) watch a burst of frames ethernet with the destination MAC address of the VM (which owns 1.1.1.1) in the output of tcpdump

  Cisco Configuration:

  hostname switch1
  !
  src-dst-ip port-channel load-balance

  !

  interface GigabitEthernet1/0/4

  Description vmnic0.host0 (NIC 1)

  switchport trunk encapsulation dot1q

  switchport mode trunk

  channel-group mode 4 on

  spanning tree portfast trunk

  end

  !

  interface GigabitEthernet2/0/4

  Description vmnic1.host0 (NIC 2)

  switchport trunk encapsulation dot1q

  switchport mode trunk

  channel-group mode 4 on

  spanning tree portfast trunk

  end

  !

  Interface Port-Channel 4

  Host0 description

  switchport trunk encapsulation dot1q

  switchport mode trunk

  spanning tree portfast trunk

  end

  
  Configuration of ESXi
  vSwitch0

  Grouping of NETWORK cards / Load Balancing: route based on IP Hash
  Grouping of NETWORK cards / failover detection network: link status only
  Grouping of NETWORK cards / notify switches: Yes
  NIC Teaming / relief: Yes
  Grouping of NETWORK cards / adapters active: vmnic0, vmnic1
  NIC Teaming / standby adapters: nothingness
  NIC adapters grouping / unused: nothingness
  Security / Promiscious Mode: reject

  Security / MAC address changes: accept
  Security / forged passes: accept

  
  #1 Virtual Machine port group
  Network label: 'Public '.

  VLAN: 27
  Grouping of NETWORK cards: all unchecked (inherited)

  #2 Virtual Machine port group
  Network label: "trunk".
  VLAN: 4095
  Grouping of NETWORK cards: all unchecked (inherited)

  VM kernel Port #1
  Network label: 'management '.
  VLAN: 2

  Grouping of NETWORK cards: all unchecked (inherited)

  VM #1
  

  OS: Windows Server 2003
  NIC 1 / adapter: Flexible
  NIC 1 / network Label: 'Public '.

  IP address: 1.1.1.1/24

  I apologize for the delay in my response.

  Unplug physically 2 cable NETWORK card on the host and configuration mirrored port on the switchport to 1 NETWORK adapter of the host, I have been able to confirm that the host VMWare issues guides on NIC1 with a destination MAC address of one of its own VM.

  After carefully reviewing the captured data, I noticed that the destination frames wrong "02:bf:cb:50:a2:76" MAC address actually belonged to "Local Area Connection 1' one of my Windows 2003 Server WHAT VM installed on the suspected host.

  Dig a little deeper, I discovered that this virtual NETWORK card is presented to the operating system as
  Name: Local 1 network connection
  "Type: VMware Accelerated AMD PCNet adapt."
  MAC: 02-BF-CB-50-A2-76

  But the configuration of the virtual machine in vCentre is
  Name: Network adapter 1
  Type: Flexible
  MAC: 00: 0C: 29:fa:e8:83

  Note the different MAC addresses.

  Digging a little further I discovered that Windows 2003 server has configured on "Local 1 network connection" network load balancing and NLB is the cause of the altered MAC address.

  Rather than to investigate further I have just placed a load balancer linux before the server windows 2003 cluster and that you turn off NLB.

  But I suspect that there is still a fundamental problem in the Virtual Switch VMware with how he learns the MAC addresses of the virtual machine is using flexible vNIC. In particular, with a virtual machine that uses a form to override the MAC address such as that used by NLB.

• iDRAC 7 express, grouping of network cards

  Hello

  I can't access iDRAC when the grouping of NETWORK cards is configured. Is it according to the design guidelines? There is no work around for this?

  #idrac7express #NICteaming  

  Hello.

  Yes, it's normal. IDRAC Express does NOT use a NETWORK card dedicated for remote access, but rather use a LAN on motherboard (LOM) as a shared port. Now, once you have Teaming on the LOM ports, then the iDRAC Express cannot share all the ports with the team. The solution is to upgrade to iDRAC Enterprise that uses another port dedicated team card NETWORK for management traffic. See page 4 of the link: downloads.dell.com/.../integrated-dell-remote-access-cntrllr-7-v1.30.30_Setup%20Guide_en-us.pdf;. l = en & cs = 555 & s = biz

• Grouping of NETWORK cards

  Hello

  I am new to virtualization and have a basic question about the collection of NETWORK adapters. I have a host with a NETWORK card with 2 ports (vmnic0 and vmnic1). I have a network cable connected to vmnic0 and vmnic1 is open without any network connection to the outside world. Can I use grouping of NETWORK cards in this case? Or both network adapters must be connected to the network for NIC teaming to work?

  You can certainly configure everything as if the two vmnic was active. However, with a single uplink connected to a physical switch, it may not make much sense.

  André

• vSphere replication - grouping of NETWORK cards

  We have a large virtual machine (60 to VMDK) we need to replicate to a second host.  We are currently receiving about 100 MB/s and it seems we're reached the limit of 1 GB.  I want to increase the bandwidth available for this large replication work by aggregating traffic through several nic is it possible?  If so, how?

  I tried the following approach, thinking that these operations can be based on the same transfer mechanism, but it has not made a difference.

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & addresses...

  The KB points it is grouping of network cards that will help when you lost the active NIC then stand by will pass your tgraffic.

  Now coming to your scenario, you need to configure the user profile of the NIOC here you have to devote all the speed of the network to this replication job card. You cannot aggregate multiple Nic for reaching the combined capacity. We have a concept called LAG and LACP. but it will also give the speed that is independent to the different traffic

• Grouping of NETWORK cards reverse the policy

  When I apply a profile esxi 5.0 to 5.1 host, I got the following configuration message. any ideas?

  Hello

  This is mentioned in the 5.1 version of vSphere notes:

  Compliance policy network outages continue to host profiles created from applied guests 5.1 ESXi ESXi 4.1 or ESXi 4.0 hosts
  After you apply a profile created from an ESXi 4.1 or ESXi 4.0 host host to a 5.1, the failures of compliance profile next host ESXi host could continue:

  For the network policy for the Group [NAME of GROUP of PORT] port spec.policy.nicTeaming.failureCriteria property does not match
  For the network policy for the Group [NAME of GROUP of PORT] port spec.policy.nicTeaming.reversePolicy property does not match

  
  

  Network settings above are not supported on ESXi 5.1 hosts and are configured is more when you apply a host profile with these settings.

  Solution: Two options are available:

  • After applying host initially created from an ESXi 4.1 host to a host profile ESXi 5.1, create a new profile of the host from the host ESXi 5.1 and which attach to this 5.1 ESXi host and other affected 5.1 ESXi hosts.
  • Change the policy of grouping of NETWORK adapters in the profile of the host to the option user must explicitly choose political instead of the strategy of grouping NIC specified.

  Now I know IVotre profiles are at the origin of 5.0 but the thought to mention it anyway

• groups of network XP and win7

  is there a way to get my xp and win7 computers in the same network group?  I wnt to use easy transfer but my new machine can not find the old

  Hello

  Win7 when configured on the peer-to-peer network has three types of configurations of sharing.

  Group residential network = only works between Win 7 computers. This type of configuration, it is very easy to entry level users to start sharing network.

  Working network = fundamentally similar to previous methods of sharing that allow you to control what, how and to whom the records would be shared with.
  
  Public share = network Public (as Internet Café) in order to reduce security risks.

  For the best newspaper of the results of each computer screen system and together all computers on a network of the same name, while each computer has its own unique name.

  http://www.ezlan.NET/Win7/net_name.jpg

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq.html#trusted
  Please Note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic.

  If you end up with the 3rd party software uninstalled or disabled, make sure that Windows native firewall is active .

  -------------------

  Network Win 7 with another version of Windows as a work network (works very well if all computers are Win 7 also).

  In the center of the network, by clicking on the type of network opens the window to the right.

  Choose your network type. Note the check box at the bottom and check/uncheck depending on your needs.

  http://www.ezlan.NET/Win7/net_type.jpg

  Win 7 - http://windows.microsoft.com/en-us/windows7/Networking-home-computers-running-different-versions-of-Windows

  Win 7 network sharing folder specific work - http://www.onecomputerguy.com/windows7/windows7_sharing.htm

  Windows XP file sharing - http://support.microsoft.com/default.aspx?scid=kb;en-us;304040

  In Win XP Pro with simple sharing Off, you can visually see the Permission/security level and set them up at your convenience.

  http://www.Microsoft.com/windowsxp/using/security/learnmore/AccessControl.mspx#securityTab

  Sharing printer XP - http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

  Setting Windows native firewall for sharing XP - http://support.microsoft.com/kb/875357
  When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

  -------------

  If you have permission and security issues with Vista/Win7, check the following settings.

  Point to a folder that wants to share do right click and choose Properties.

  In the properties

  Click on the Security tab shown in the bellows of the photo on the right) and verify that users and their permissions (see photo below Centre and left) are configured correctly. Then do the same for the authorization tab.

  This screen shot is to Win 7, Vista menus are similar.

  http://www.ezlan.NET/Win7/permission-security.jpg

  The Security Panel and the authorization Panel, you need to highlight each user/group and consider that the authorization controls are verified correctly.

  When everything is OK, restart the network (router and computer).

  * Note . The groups and users listed in the screen-shoot are just an example. Your list will focus on how your system is configured.

  * Note . All the users who are allowed to share need to have an account onall computers that they are allowed to connect to.

  Everyone is an account, that means a group of all users who already have an account now as users. It is available to avoid the need to configure permission for each on its own, it does not mean all those who feel that they would like to connect.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Hello

  I'm trying to understand how to configure a dedicated server of Dell R210 rented running VMware ESXi 5.1.0 build-799733

  This dedicated server is rented www.online.net and sits somewhere in France. One of its network adapters have an IP public 62.210.177.20x. The other NIC is here, but I do not understand how it is configured. According to the www.online.net portal, the other NETWORK card has or should have an IP 10.90.116.20x. And I am obviously set up is to have some virtual machines running and be able to access the Internet. I have access to the console of the server Dell through iDRAC and since I could see, one of the network adapters in the IP is 62.210.177.20x defined, and the other has been shown out of service. I managed to make it appear the other interface but I cannot find anywhere how to assign the IP address 10.90.116.20x to this 2^nd network adapter. But then again I don't even know if I should or if I need to assing a IP address to this 2^nd network adapter. What is the cable connected even for this 2^nd NIC? I do not know. Should it be - I'm not either. I don't know French and manuals/instructions on www.online.net are in French. I can try an online translator, but I don't think that what I'm looking for is explained. How do I get this set up? I have to do something about the ESXi on the server console? This interface 2^nd should be in place, or it must be down as if it was originally? Yesterday after watching someone videos on YouTube, I added the second virtual switch and moved the virtual hosts of this switch 2 and he entrusted the 2^nd NIC. But that 2^nd NIC had a red X next to it probably indicating that it was disconnected the 2^nd form virtual switch. Today and now I have managed to access the ESXi console server through iDRAC, I bring the 2^nd NIC, and now both network adapters are assigned to the virtual switch 1^st . But I think that a NIC should be attributed to a single switch and the other card NETWORK on the 2^nd switch. I'm just a desktop guy with enough knowledge to be dangerous J if you / someone put in steps how and where to set them up it... PLEASE

  Thanks in advance

  cweks

  ~ # vmware - v

  VMware ESXi 5.1.0 build-799733

  ~ # esxcfg - road

  VMkernel default gateway is 62.210.177.1

  ~ # esxcfg-vmknic-list

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  vmk0 management network IPv4 62.210.177.20x 255.255.255.0 62.210.177.255 d4:ae:52:cb:bb:84 1500 65535 true STATIC

  vmk0 networking fe80::d6ae:52ff:xxxx:bb84 64 d4:ae:52:cb:bb:84 1500 65535 true IPv6 STATIC, PREFERRED

  Portal www.online.NET--information

  NORMAL 1 ready 62.210.177.20x xxx.domain.eu.       D4:AE:52:AB:BB:84

  2 PRIVATE loan 10.90.116.20x d4:ae:52:ab:bb:85

  http://wiki.hetzner.de/index.php/VMware_ESXi/en#Network_configuration

  Network configuration

  • VMware vSphere Hypervisor is an "operating system" for pure virtualization and support NAT or routing. Therefore, only a real bridge configuration can be used.
  • To use a subnet additional IP must be configured as a router VM.

  If I understand the above, I need to show some VM and set up as a router? If the virtual machine that will act as a router must have two network interfaces, where it is connected to a switch and the other to the other switch network card. Am I do? The YouTube video that suggested, but I thought that maybe / somehow ESXi can route packets between the two network cards, but from what I read, ESXi can route packets. Do I need to order an additional / extra / 2nd IPv4 address so that it can be assigned to the interface of the router?

• How many switches must be configured and min no network interface cards?

  Hello

  We will implement the ESXi5.0.

  We would like to know if we use different ports for network management and vMotion groups?  It seems that two of them use the same (different from ESX 4) IP address.

  In addition, my supervisor would like to know what is the minimum number of network interface cards to use (because the server has no slot PCIe)?

  Your opinion is requested.

  Thank you

  TonyJK wrote:

  Since we implement VLANS on our site and based on the documentation, ESXi 5 gets only 1 battery IP, wonder what is the best way to cope.

  It is true that ESXi has that one battery IP, which is very good compared to the other two in ESX (Linux in the Service Console and the Vmkernel). However, we have only an IP stack means that it is the same driver tcp/ip, but does not mean that we cannot have multiple IP addresses.

  For example, you can create a Vmkernel how many interfaces you want and assign different IP addresses, which could be on the same network or on different.

  Even if you don't have a VLAN in your environment I would still recommend using another IP network for vMotion for your management. This will make the two a little more 'best practice', easier to different and you would be good too preperred if you implement VLANs in the future.

• Load balancing across the NETWORK interface card

  Hello

  Our ESX Server's NIC six, two for SAN, one to the dedicated Service Console and three for the virtual computer LAN traffic. I noticed one thing look in the performance tab in VC, is that all LAN traffic seems to go on one of the three the NIC and the other two are practically inactive.

  If I look at the network configuration for the vSwitch those with three cards network, grouping of NETWORK cards is set for 'road based on the original virtual port code '.

  Can anyone advise how to get a more 'democratic' usage of the three NETWORK adapter?

  
  
  As seen on http://www.eqlforums.com !

  How many virtual machines you host? With the load balancing algorithm you have selected (default), traffic is balanced to the vNIC level (i.e. all traffic from a given vNIC always through the same bear). This is the case for all, but the IP hash algorithm, which requires you to 802.3ad static port aggregation on your pSwitch. In most cases, there is no need to worry about the use of bear - if it's a GbE NETWORK card, you're probably not close to push the limits.

  Ken Cline

  Technical Director, virtualization

  Wells Landers

  TVAR Solutions, a company of the Wells Landers group

  VMware communities user moderator

• HP Pavilion a6330f desktop PC: is it possible to update my Network Interface Card?

  Is it possible to replace and modernize the Network Interface Card that I have (10/100 Base-T Network Interface)?  If Yes, do you have a recommendation indicating what replacement card should I buy?  The network interface that I have now I cannot take advantage of very high speed that my internet provider (150mmps).  Thanks for your help with this... Mike

  You are welcome.  Thank you for the additional information.

  Here is a card that should work for you:

  http://www.Amazon.com/TP-link-TG-3468-1000Mbps-Gigabit-express/DP/B003CFATNI/ref=sr_1_1?ie=UTF8 & qid = 1420761130 & SR = 8-1 & Keywords = PCIe-x 1 + Network + Card

  Read the reviews to see what users say about it.  You should disable the network adapter before you install it.  There is a PCI slot and the PCI Express x 1 slot is faster.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• my pc will not connect to wireless internet... It is said there could be a problem with the driver for the wireless network connection card

  connection network card

  my pc will not connect to wireless internet... It is said there could be a problem with the driver for the wireless network connection card... I'm not sure how to solve the problem of the dat

  Hello

  Did you change your computer?

  I suggest you to follow the links and check out them.

  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Solve problems, find wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Tips for solving common driver problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems

• DELL UPS Network Management Card firmware update is not possible in the management of inverter DELL Multi console

  I have a problem with the update of some old software on a DELL UPS Network Management card in DELL Multi UPS Management Console.

  We have a few more recent and some models with very old Firmware. The older firmware is: 01.02.0013
  I imported the update of the firmware: 01.16.0001
  If I select this version behind the inverter with firmware 01.02.0013 it is a red exclamation point.

  

  Also, I can't get to the this inverter https address.

  So I do not know how update the firmware of the network management card, please anyone who has a solution...

  .

  I got it finally working.

  I couldn't connect to the interface webGui of UPS in https on IE 6,7,8,9 and calibrated to an ssl error Firefox.
  I could not update the firmware using DELL UPS management software can. fatal error.

  I then installed Chrome, when connecting to the web GUI I ignored the warning of certificate error and waited...

  YES. The web Gui appeared, asking for the password and the Web GUI that I could install the firmware 01.14.0003

  After the update of the firmware in the webgui I was able to upgrade to 01.16.0001 in DELL UPS software Multi management.

  

• problem witththe driver for the wireless network connection card

  Quite suddenly my laptop (Toshiba) could not connect to my Modem and printer. I can only connect to the internet with a cable connection to the modem. The printer reports no problem with the connection. Troubleshooting report 'Problem with the driver for the wireless network connection card.' Problems also with ISATAP MS Driver adapter and Teredo Tunneling adapter. Software could not solve the problem.  A technician online know-how also faled to solve the problem after an hour trying everything - uninstalling and reinstalling, etc. He thought it would be a virus even though I have several active antivirus programs. Any ideas? Should I chuck the laptop away and buy a new one?

  If, as you say, you have several active antivirus running programs, they will conflict with each other and you will have no protection

  Visit the support of Tosh, specific to your model, and reinstall the drivers for the chipset and wireless

• Unity and double network interface cards

  The unit works well with 2 network cards? Tips or tricks if you use 2 network cards? They are one of the subnets differnet 2. My voicemail ports are registered in CallManager, but on a different subnet from the CallManager is on. And this isn't the MAC for the NETWORK card that my license file is for.

  Two NETWORK adapters is supported only in a configuration Active / Passive with the unit. Both NICs must share the same IP address. 2 cards using NETWORK in an active scenario can cause audio one-way and MWI problems. Please see the links below for confirmation.

  Configuration and troubleshooting of network interface cards double for Cisco Unity

  http://www.Cisco.com/en/us/products/SW/voicesw/ps2237/products_tech_note09186a00801d1c56.shtml

  Troubleshooting Cisco Unity

  http://www.Cisco.com/en/us/products/SW/voicesw/ps2237/prod_troubleshooting_guide_chapter09186a008015082b.html

  I hope this helps. If so, please indicate the position.

  Brandon