Groups of vpn Cisco ASA5510 8.3

Similar Questions

• Need help with the configuration of the Site with crossed on Cisco ASA5510 8.2 IPSec VPN Client (1)

  Need urgent help in the configuration of the Client VPN IPSec Site with crossed on Cisco ASA5510 - 8.2 (1).

  Here is the presentation:

  

  There are two leased lines for Internet access - a route 1.1.1.1 and 2.2.2.2, the latter being the default Standard, old East for backup.

  I was able to configure the Client VPN IPSec Site

  (1) with access to the outside so that the internal network (172.16.0.0/24) behind the asa

  (2) with Split tunnel with simultaneous assess internal LAN and Internet on the outside.

  But I was not able to make the tradiotional model Hairpinng to work in this scenario.

  I followed every possible suggestions made on this subject in many topics of Discussion but still no luck. Can someone help me here please?

  Here is the race-Conf with Normal Client to Site IPSec VPN configured with no access boarding:

  LIMITATION: Cannot boot into any other image ios for unavoidable reasons, must use 8.2 (1)

  race-conf - Site VPN Customer normal work without internet access/split tunnel

  : ASA Version 8.2 (1) ! ciscoasa hostname domain cisco.campus.com enable the encrypted password xxxxxxxxxxxxxx XXXXXXXXXXXXXX encrypted passwd names of ! interface GigabitEthernet0/0 nameif outside internet1 security-level 0 IP 1.1.1.1 255.255.255.240 ! interface GigabitEthernet0/1 nameif outside internet2 security-level 0 IP address 2.2.2.2 255.255.255.224 ! interface GigabitEthernet0/2 nameif dmz interface security-level 0 IP 10.0.1.1 255.255.255.0 ! interface GigabitEthernet0/3 nameif campus-lan security-level 0 IP 172.16.0.1 255.255.0.0 ! interface Management0/0 nameif CSC-MGMT security-level 100 the IP 10.0.0.4 address 255.255.255.0 ! boot system Disk0: / asa821 - k8.bin boot system Disk0: / asa843 - k8.bin passive FTP mode DNS server-group DefaultDNS domain cisco.campus.com permit same-security-traffic inter-interface permit same-security-traffic intra-interface object-group network cmps-lan the object-group CSC - ip network object-group network www-Interior object-group network www-outside object-group service tcp-80 object-group service udp-53 object-group service https object-group service pop3 object-group service smtp object-group service tcp80 object-group service http-s object-group service pop3-110 object-group service smtp25 object-group service udp53 object-group service ssh object-group service tcp-port port udp-object-group service object-group service ftp object-group service ftp - data object-group network csc1-ip object-group service all-tcp-udp access list INTERNET1-IN extended permit ip host 1.2.2.2 2.2.2.3 access-list extended SCC-OUT permit ip host 10.0.0.5 everything list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq www list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any https eq list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq ssh list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 no matter what eq ftp list of access CAMPUS-LAN extended permitted udp 172.16.0.0 255.255.0.0 no matter what eq field list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq smtp list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq pop3 access CAMPUS-wide LAN ip allowed list a whole access-list CSC - acl note scan web and mail traffic access-list CSC - acl extended permit tcp any any eq smtp access-list CSC - acl extended permit tcp any any eq pop3 access-list CSC - acl note scan web and mail traffic access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 993 access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq imap4 access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 465

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq www

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq https

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq smtp

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq pop3

  access-list extended INTERNET2-IN permit ip any host 1.1.1.2

  access-list sheep extended ip 172.16.0.0 allow 255.255.0.0 172.16.0.0 255.255.0.0

  access list DNS-inspect extended permit tcp any any eq field

  access list DNS-inspect extended permit udp any any eq field

  access-list extended capin permit ip host 172.16.1.234 all

  access-list extended capin permit ip host 172.16.1.52 all

  access-list extended capin permit ip any host 172.16.1.52

  Capin list extended access permit ip host 172.16.0.82 172.16.0.61

  Capin list extended access permit ip host 172.16.0.61 172.16.0.82

  access-list extended capout permit ip host 2.2.2.2 everything

  access-list extended capout permit ip any host 2.2.2.2

  Access campus-lan_nat0_outbound extended ip 172.16.0.0 list allow 255.255.0.0 192.168.150.0 255.255.255.0

  pager lines 24

  Enable logging

  debug logging in buffered memory

  asdm of logging of information

  Internet1-outside of MTU 1500

  Internet2-outside of MTU 1500

  interface-dmz MTU 1500

  Campus-lan of MTU 1500

  MTU 1500 CSC-MGMT

  IP local pool 192.168.150.2 - 192.168.150.250 mask 255.255.255.0 vpnpool1

  IP check path reverse interface internet2-outside

  IP check path reverse interface interface-dmz

  IP check path opposite campus-lan interface

  IP check path reverse interface CSC-MGMT

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 621.bin

  don't allow no asdm history

  ARP timeout 14400

  interface of global (internet1-outside) 1

  interface of global (internet2-outside) 1

  NAT (campus-lan) 0-campus-lan_nat0_outbound access list

  NAT (campus-lan) 1 0.0.0.0 0.0.0.0

  NAT (CSC-MGMT) 1 10.0.0.5 255.255.255.255

  static (CSC-MGMT, internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255

  Access-group INTERNET2-IN interface internet1-outside

  group-access INTERNET1-IN interface internet2-outside

  group-access CAMPUS-LAN in campus-lan interface

  CSC-OUT access-group in SCC-MGMT interface

  Internet2-outside route 0.0.0.0 0.0.0.0 2.2.2.5 1

  Route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  AAA authentication enable LOCAL console

  Enable http server

  http 10.0.0.2 255.255.255.255 CSC-MGMT

  http 10.0.0.8 255.255.255.255 CSC-MGMT

  HTTP 1.2.2.2 255.255.255.255 internet2-outside

  HTTP 1.2.2.2 255.255.255.255 internet1-outside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs set group5

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  Crypto map internet2-outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  crypto internet2-outside_map outside internet2 network interface card

  Crypto ca trustpoint _SmartCallHome_ServerCA

  Configure CRL

  Crypto ca certificate chain _SmartCallHome_ServerCA

  certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as

  quit smoking

  ISAKMP crypto enable internet2-outside

  crypto ISAKMP policy 10

  preshared authentication

  aes encryption

  md5 hash

  Group 2

  life 86400

  Telnet 10.0.0.2 255.255.255.255 CSC-MGMT

  Telnet 10.0.0.8 255.255.255.255 CSC-MGMT

  Telnet timeout 5

  SSH 1.2.3.3 255.255.255.240 internet1-outside

  SSH 1.2.2.2 255.255.255.255 internet1-outside

  SSH 1.2.2.2 255.255.255.255 internet2-outside

  SSH timeout 5

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal VPN_TG_1 group policy

  VPN_TG_1 group policy attributes

  Protocol-tunnel-VPN IPSec

  username ssochelpdesk encrypted password privilege 15 xxxxxxxxxxxxxx

  privilege of encrypted password username administrator 15 xxxxxxxxxxxxxx

  username vpnuser1 encrypted password privilege 0 xxxxxxxxxxxxxx

  username vpnuser1 attributes

  VPN-group-policy VPN_TG_1

  type tunnel-group VPN_TG_1 remote access

  attributes global-tunnel-group VPN_TG_1

  address vpnpool1 pool

  Group Policy - by default-VPN_TG_1

  IPSec-attributes tunnel-group VPN_TG_1

  pre-shared-key *.

  !

  class-map cmap-DNS

  matches the access list DNS-inspect

  CCS-class class-map

  corresponds to the CSC - acl access list

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  CCS category

  CSC help

  cmap-DNS class

  inspect the preset_dns_map dns

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y

  : end

  Adding dynamic NAT for 192.168.150.0/24 on the external interface works, or works the sysopt connection permit VPN

  Please tell what to do here, to pin all of the traffic Internet from VPN Clients.

  That is, that I need clients connected via VPN tunnel, when connected to the internet, should have their addresses IP NAT'ted against the address of outside internet2 network 2.2.2.2 interface, as it happens for the customers of Campus (172.16.0.0/16)

  I am well aware of all involved in here, so please be elaborative in your answers. Please let me know if you need more information about this configuration to respond to my request.

  Thank you & best regards

  MAXS

  
  

  Hello

  If possible, I'd like to see that a TCP connection attempt (e.g. http://www.google.com) in the ASDM logging of the VPN Client when you set up the dynamic NAT for the VPN Pool also.

  I'll try also the command "packet - trace" on the SAA, while the VPN Client is connected to the ASA.

  The command format is

  packet-tracer intput tcp

  That should tell what the SAA for this kind of package entering its "input" interface

  Still can not see something wrong with the configuration (other than the statement of "nat" missing Dynamics PAT)

  -Jouni

• IOS router with several groups of VPN

  Similar to a discussion, I read with a PIX firewall, I need to set up multiple VPN groups on IOS-based router to support different levels of security. For example, a VPN "GUESTS" group would only have access to 1 server, while the VPN "ADMIN" group would have access to the entire network.

  With a PIX firewall, you can simply specify additional group names (for example "group1 vpngroup',"vpngroup group2"and so on). However, I have not been able to find how do with IOS-based router (Cisco 831 12.3 (4) T) running.

  For example, I have these dynamic groups of VPN:

  the crypto isakmp client configuration group of GUESTS

  password1 keys

  DNS 10.1.1.1

  swimming POOL1-IP pool

  Configuration group customer crypto isakmp ADMIN

  key password2

  DNS 10.1.1.1

  POOL2-IP pool

  ! - Users get authenticated to a RADIUS server

  list of card crypto CRYPTOMAP customer VPN-USER authentication

  ! - The problem is that line taken out. "I can only specify an allow list (a group name) for this encryption card!)

  card crypto CRYPTOMAP ADMIN isakmp authorization list

  I did research on this site, Google, usenet and ORC and have not found what I'm looking for. Any ideas?

  Thank you.

  Command 'isakmp authorization list' you do it reference does not refer to the VPN group, it refers to a whitelist of AAA name which States that the groups are configured locally. Change to the following:

  AAA authorization groupauthor LAN

  card crypto isakmp authorization list groupauthor CRYPTOMAP

  The "groupauthor" is just a label that matches the encryption to the aaa command. Your clients VPN will be accompanied to a specific group depends on what group name, they set up in their VPN client.

  See http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080095106.shtml for details, it's a HW 3002 client to a router but the router config is exactly the same thing.

• Assign the radius server to specific groups of VPN 3000

  Last week, I assigned a test Cisco ACS server to be used for authentication and device of accounting for a specific group on a Cisco VPN concentrator 3060. When I looked at ACS, it appears that not only the Group was to go there but others through this way and using the default values on the Cisco Secure ACS. Is it possible that I can make sure only the traffic assigned to this specific group of VPN using the ACS server defined?

  Thank you

  Hello

  Not sure about your implementation. But you must configure the group for this specific ad group map can only authentication.

  In the external group map db, map

  Group ACS VPN---> with<---- ad="" vpn="">

  Any other combination should point to any access group.

  Kind regards

  ~ JG

  Note the useful messages

• Client VPN Cisco router Cisco, MSW CA + certificates

  Dear Sirs,
  Let me approach you on the following problem.

  I wanted to use a secure between the Cisco VPN client connection
  (Windows XP) and Cisco 2821 with certificate-based authentication.
  I used the Microsoft certification authority (Windows 2003 server).
  Cisco VPN client used eTokenPRO Aladdin as a certificate store.

  Certificate of MSW CA registration and implementation in eToken ran OK
  Customer VPN Cisco doesn't have a problem with the cooperation of eToken.
  Certificate of registration of Cisco2821 MSW ca ran okay too.

  Cisco 2821 configuration is standard. IOS version 12.4 (6).

  Attempt to connect to the client VPN Cisco on Cisco 2821 was
  last update of the error messages:

  ISAKMP: (1020): cannot get router cert or routerdoes do not have a cert: had to find DN!
  ISAKMP: (1020): ITS been RSA signature authentication more XAUTH using id ID_FQDN type
  ISAKMP (1020): payload ID
  next payload: 6
  type: 2
  FULL domain name: cisco - ca.firm.com
  Protocol: 17
  Port: 500
  Length: 25
  ISAKMP: (1020): the total payload length: 25
  ISAKMP (1020): no cert string to send to peers
  ISAKMP (1020): peer not specified not issuing and none found appropriate profile
  ISAKMP (1020): Action of WSF returned the error: 2
  ISAKMP: (1020): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
  ISAKMP: (1020): former State = new State IKE_R_MM5 = IKE_P1_COMPLETE

  Is there some refence where is possible to find some information on
  This problem? There is someone who knows how to understand these mistakes?
  Thank you very much for your help.

  Best regards
  P.Sonenberk

  PS Some useful information for people who are interested in the above problem.

  Address IP of Cisco 2821 10.1.1.220, client VPN IP address is 10.1.1.133.
  MSW's IP 10.1.1.50.
  Important parts of the Cisco 2821 configuration:

  !
  cisco-ca hostname
  !
  ................
  AAA new-model
  !
  AAA authentication login default local
  AAA authentication login sdm_vpn_xauth_ml_1 local
  AAA authorization exec default local
  AAA authorization sdm_vpn_group_ml_1 LAN
  !
  ...............
  IP domain name firm.com
  host IP company-cu 10.1.1.50
  host to IP cisco-vpn1 10.1.1.133
  name of the IP-server 10.1.1.33
  !
  Authenticated MultiLink bundle-name Panel
  !
  Crypto pki trustpoint TP-self-signed-4097309259
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 4097309259
  revocation checking no
  rsakeypair TP-self-signed-4097309259
  !
  Crypto pki trustpoint company-cu
  registration mode ra
  Enrollment url http://10.1.1.50:80/certsrv/mscep/mscep.dll
  use of ike
  Serial number no
  IP address no
  password 7 005C31272503535729701A1B5E40523647
  revocation checking no
  !
  TP-self-signed-4097309259 crypto pki certificate chain
  certificate self-signed 01
  30820249 308201B 2 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
  .............
  FEDDCCEA 8FD14836 24CDD736 34
  quit smoking
  company-cu pki encryption certificate chain
  certificate 1150A66F000100000013
  30820509 308203F1 A0030201 02020 HAS 11 092A 8648 01000000 13300 06 50A66F00
  ...............
  9E417C44 2062BFD5 F4FB9C0B AA
  quit smoking
  certificate ca 51BAC7C822D1F6A3469D1ADC32D0EB8C
  30820489 30820371 A0030201 BAC7C822 02021051 D1F6A346 9D1ADC32 D0EB8C30
  ...............
  C379F382 36E0A54E 0A6278A7 46
  quit smoking
  !
  ...................
  crypto ISAKMP policy 30
  BA 3des
  md5 hash
  authentication rsa-BA
  Group 2
  ISAKMP crypto identity hostname
  !
  Configuration group customer isakmp crypto Group159
  key Key159Key
  pool SDM_POOL_1
  ACL 100
  !
  the crypto isakmp client configuration group them
  domain firm.com
  pool SDM_POOL_1
  ACL 100
  !
  Crypto ipsec transform-set esp-3des esp-md5-hmac 3DES-MD5
  !
  crypto dynamic-map SDM_DYNMAP_1 1
  the transform-set 3DES-MD5 value
  market arriere-route
  !
  card crypto SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
  map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto
  client configuration address map SDM_CMAP_1 crypto answer
  map SDM_CMAP_1 65535-isakmp dynamic SDM_DYNMAP_1 ipsec crypto
  !
  ................
  !
  end

  status company-cu of Cisco-ca #show cryptographic pki trustpoints
  Trustpoint company-cu:
  Issuing CA certificate configured:
  Name of the object:
  CN = firm-cu, dc = company, dc = local
  Fingerprint MD5: 5026582F 8CF455F8 56151047 2FFAC0D6
  Fingerprint SHA1: 47B 74974 7C85EA48 760516DE AAC84C5D 4427E829
  Universal router configured certificate:
  Name of the object:
  host name = cisco - ca.firm.com
  Fingerprint MD5: E78702ED 47D5D36F B732CC4C BA97A4ED
  Fingerprint SHA1: 78DEAE7E ACC12F15 1DFB4EB8 7FC DC6F3B7E 00138
  State:
  Generated keys... Yes (general purpose, not exportable)
  Authenticated issuing certification authority... Yes
  Request certificate (s)... Yes

  Cisco-ca #sh crypto pubkey-door-key rsa
  Code: M - configured manually, C - excerpt from certificate

  Name of code use IP-address/VRF Keyring
  C Signature name of X.500 DN default:
  CN = firm-cu
  DC = company
  DC = local

  C signature by default cisco-vpn1

  IMPORTANT: I don't have a Cisco IOS Software: 12.4 (5), 12.3 (11) T08, 12.4 (4.7) PI03c,.
  12.4 (4.7) T - there is error in the cryptographic module.

  Hey guys, it's weird that the router is not find cert after IKE is the cert and validates, it is certainly not reason, but I would go ahead and set up the mapping of certificate on this router to force the client to associate with Group of IKE, for that matter, that you need to change your config a bit for use iskamp profiles :

  http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t8/feature/guide/gt_isakp.html

• IPSec vpn cisco asa and acs 5.1

  We have configured authentication ipsec vpn cisco asa acs 5.1:

  Here is the config in cisco vpn 5580:

  standard access list acltest allow 10.10.30.0 255.255.255.0

  RADIUS protocol AAA-server Gserver

  AAA-server host 10.1.8.10 Gserver (inside)

  Cisco key

  AAA-server host 10.1.8.11 Gserver (inside)

  Cisco key

  internal group gpTest strategy

  gpTest group policy attributes

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list acltest

  type tunnel-group test remote access

  tunnel-group test general attributes

  address localpool pool

  Group Policy - by default-gpTest

  authentication-server-group LOCAL Gserver

  authorization-server-group Gserver

  accounting-server-group Gserver

  IPSec-attributes of tunnel-group test

  pre-shared-key cisco123

  GBA, we config user group: VPN users. all VPN users in this group. ACS can visit his political profile: If the user in the 'VPN users' group, access ACS.

  When we connect from a VPN Client to the server, all users connect to success. When you see the parser in ACS journal, each user success connect also get

  error:

  22040 wrong password or invalid shared secret

  (pls see picture to attach it)

  the system still works, but I don't know why, we get the error log.

  Thanks for any help you can provide!

  Duyen

  Hello Duyen,

  I think I've narrowed the issue. When remote access VPN using RADIUS authentication we must keep in mind that authentication and authorization are included on the same package.

  Depending on your configuration, the ACS is defined as a server RADIUS (Gserver Protocol radius aaa server) and becomes the VPN Tunnel authenticated and 'authorized' on this server group:

  authentication-server-group LOCAL Gserver

  authorization-server-group Gserver

  As noted above, the RADIUS of request/response includes authentication and authorization on the same package. This seems to be a problem of incorrect configuration that we should not set up the 'permission' in the Tunnel of the group.

  Please remove the authorization under the Tunnel of Group:

  No authorization-server-group Gserver

  Please test the connection again and check the logs of the ACS. At this point there are only sucessful newspaper reported on the side of the ACS.

  Is 'Permission-server-group' LDAP permission when authenticating to a LDAP server so to retrieve the attributes of permission on the server. RAY doesn't have the command as explained above.

  I hope this helps.

  Kind regards.

• Order of operations NAT on Site to Site VPN Cisco ASA

  Hello

  I have a question about the order of operations NAT on Site to Site VPN Cisco ASA 8.2.x. I have a scenario where the internal IP address of the range 10.17.128.x are NATTED IP public 31.10.10.x. below is the config:

  Tunnel normally passes traffic to dmz - 31.10.11.10, 31.10.11.11 servers.

  But the servers NATTED (10.17.128.x <->31.10.10.x) does not work.

  inside_map crypto 50 card value transform-set ESP-3DES-SHA

  tunnel-group 100.1.1.1 type ipsec-l2l

  tunnel-group 100.1.1.1 General-attributes

  Group Policy - by default-PHX_HK

  IPSec-attributes tunnel-group 100.1.1.1

  pre-shared key *.

  internal PHX_HK group policy

  PHX_HK group policy attributes

  VPN-filter no

  Protocol-tunnel-VPN IPSec svc webvpn

  card crypto inside_map 50 match address outside_cryptomap_50

  peer set card crypto inside_map 50 100.1.1.1

  inside_map crypto 50 card value transform-set ESP-3DES-SHA

  inside_map crypto 50 card value reverse-road

  the PHX_Local object-group network

  host of the object-Network 31.10.11.10

  host of the object-Network 31.10.11.11

  host of the object-Network 31.10.10.10

  host of the object-Network 31.10.10.11

  host of the object-Network 31.10.10.12

  host of the object-Network 31.10.10.13

  host of the object-Network 10.17.128.20

  host of the object-Network 10.17.128.21

  host of the object-Network 10.17.128.22

  host of the object-Network 10.17.128.23

  the HK_Remote object-group network

  host of the object-Network 102.1.1.10

  inside_nat0_outbound list extended access permitted ip object-group PHX_Local-group of objects HK_Remote

  ACL_INSIDE list extended access permitted ip object-group PHX_Local-group of objects HK_Remote

  ACL_OUTSIDE list extended access permitted ip object-group HK_Remote-group of objects PHX_Local

  outside_cryptomap_50 list extended access permitted ip object-group PHX_Local-group of objects HK_Remote

  Route outside 102.1.1.10 255.255.255.255 30.1.1.1 1

  public static 31.10.10.10 (Interior, exterior) 10.17.128.20 netmask 255.255.255.255

  public static 31.10.10.11 (Interior, exterior) 10.17.128.21 netmask 255.255.255.255

  public static 31.10.10.12 (Interior, exterior) 10.17.128.22 netmask 255.255.255.255

  public static 31.10.10.13 (Interior, exterior) 10.17.128.23 netmask 255.255.255.255

  He started to work when I did another group of object by name PHX_Local1 and added to the list of access inside_nat0_outbound, instead of the object group PHX_Local, as below:

  the PHX_Local1 object-group network

  host of the object-Network 31.10.10.10

  host of the object-Network 31.10.10.11

  host of the object-Network 31.10.10.12

  host of the object-Network 31.10.10.13

  No inside_nat0_outbound access list extended only to allowed ip object-group PHX_Local-group of objects HK_Remote

  inside_nat0_outbound list extended access permitted ip object-group PHX_Local1-group of objects HK_Remote

  Can you please help me understand why group object PHX_Local failed with access-list inside_nat0_outbound, but he began to work with the Group of objects PHX_Local1.

  Also, if you could tell me the order of operations to NAT via VPN Site to Site, it would be useful.

  Thank you

  Kind regards

  Thomas

  Hello

  I think you could have said the original question in a way that could be missleading. In other words, if I understand now.

  From what I understand now, you have the DMZ set up the server that are measured with a public IP address on the real servers. And for those that you have configured NAT0.

  Then you have other servers that do not have public IP addresses themselves, but they are translated on the SAA.

  If this is the case, then the next question would be. The server with the NAT should attend the L2L VPN connection with their real IP or address IP NAT.

  Of course if you configure static NAT for the same servers and NAT0 the NAT0 will always win.

  You have these guests who were not able to use the VPN L2L

  31.10.10.10 10.17.128.20

  31.10.10.11 10.17.128.21

  31.10.10.12 10.17.128.22

  31.10.10.13 10.17.128.23

  IF you want them to go to the VPN L2L with their original IP address then you must configure

  object-group, LAN

  host of the object-Network 10.17.128.20

  host of the object-Network 10.17.128.21

  host of the object-Network 10.17.128.22

  host of the object-Network 10.17.128.23

  object-group, REMOTE network

  host of the object-Network 102.1.1.10

  inside_nat0_outbound list extended access allowed ip-group of objects LOCAL object-group remote

  outside_cryptomap_50 list extended access allowed ip-group of objects LOCAL object-group remote

  IF you want to use the L2L VPN with the public IP address, then you must configure

  object-group, LAN

  host of the object-Network 31.10.10.10

  host of the object-Network 31.10.10.11

  host of the object-Network 31.10.10.12

  host of the object-Network 31.10.10.13

  object-group, REMOTE network

  host of the object-Network 102.1.1.10

  outside_cryptomap_50 list extended access allowed ip-group of objects LOCAL object-group remote

  EDIT: in this case you naturally do not configure any NAT0 for actual IP addresses we want precisely the IP addresses to be visible to the L2L VPN with the IP NAT address.

  Or you can of course use the same "object-group" as currently but change the content in an appropriate manner

  Be sure to mark it as answered if it was answered.

  Ask more if necessary

  -Jouni

• Check the ISE for the VPN Cisco posture

  Hello community,

  first of all thank you for taking the time to read my post. I have a deployment in which requires the characteristic posture of controls for machines of VPN Cisco ISE. I know that logically once a machine on the LAN, Cisco ISE can detect and apply controls posture on clients with the Anyconnect agent but what about VPN machines? The VPN will end via a VPN concentrator, which then connects to an ASA5555X that is deployed as an IPS only. Are there clues to this?

  Thank you!

  The Cisco ASA Version 9.2.1 supports the change in RADIUS authorization (CoA) (RFC 5176). This allows for the gesticulations of users against the ISE Cisco VPN without the need of an IPN. Once a VPN user connects, the ASA redirects web traffic to the LSE, where the user is configured with a Network Admission Control (NAC) or Web Agent. The agent performs specific controls on the user's computer to determine its conformity against one together configured posture rules, such as the rules of operating system (OS) patches, AntiVirus, registry, Application, or Service.

  The posture validation results are then sent to the ISE. If the machine is considered the complaint, then the ISE can send a RADIUS CoA to the ASA with the new set of authorization policies. After validation of the successful posture and CoA, the user is allowed to access internal resources.

  http://www.Cisco.com/c/en/us/support/docs/security/Adaptive-Security-Appliance-ASA-software/117693-configure-ASA-00.html

• EZ - VPN Cisco cannot access internal network

  Hello

  I configured an EZ - VPN on my router, but after a login successful in the VPN, I can't ping my internal network or access all the resources. Also, I can't ping my router VPN Client IP address.

  Can someone take a look at my Config?

  Here is my config:

  Current configuration: 7730 bytes

  !

  ! Last configuration change at 16:24:55 UTC Tuesday, June 14, 2011 by suncci

  ! NVRAM config update at 20:21:30 UTC Friday, June 10, 2011 by suncci

  !

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  router host name

  !

  boot-start-marker

  boot-end-marker

  !

  no set record in buffered memory

  no console logging

  !

  AAA new-model

  !

  !

  AAA authentication login default local

  local AUTH_VPN AAA authentication login

  AAA authorization exec default local

  local AUTHORIZE_VPN AAA authorization network

  !

  !

  AAA - the id of the joint session

  IP cef

  !

  !

  !

  !

  name-server IP 208.67.222.222

  name of the IP-server 205.188.146.145

  !

  Authenticated MultiLink bundle-name Panel

  !

  !

  !

  !

  !

  !

  !

  !

  !

  !

  !

  !

  !

  Crypto pki trustpoint TP-self-signed-1861908046

  enrollment selfsigned

  name of the object cn = IOS - Self - signed - certificate - 1861908046

  revocation checking no

  rsakeypair TP-self-signed-1861908046

  !

  !

  TP-self-signed-1861908046 crypto pki certificate chain

  certificate self-signed 01

  3082023E 308201A 7 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030

  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30

  69666963 31383631 39303830 6174652D 3436301E 170 3032 30333031 30313431

  30365A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D

  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 38363139 65642D

  30383034 3630819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101

  8100AD30 FB88278D F9010218 AD58E479 21C00A39 76974 HAS 87 DF43C948 D56E65CC

  98F484A1 1F5BA429 449E416F B3C5729C 78598186 8873 HAS 168 DB9EEAAA B0521523

  C8011877 14888C9A 193E43E3 C3575491 74A940A2 B2970549 FE436E4A 4DA6FB23

  C 21, 20110 0CD3A8F6 32EAD292 648F9E32 7EE6C86F 181FC3C2 8F91DA66 A3886F5C

  0203 010001A 3 66306430 1 130101 FF040530 030101FF 30110603 0F060355 467D

  1104 A 0, 300882 06526F75 74657230 551D 1 230418 30168014 FD800727 1F060355

  5FA9AD41 6EAE99B0 1EDA2735 C0DBBBCC 301D 0603 551D0E04 160414FD 8007275F

  A9AD416E AE99B01E DA2735C0 DBBBCC30 0D06092A 864886F7 0D 010104 05000381

  810076CE E5030E51 5BD6FE9F A8A42483 53E7D250 CDE09E87 6AD77195 09D225AF

  25858304 034D146B C4970C31 F6EF496B 7F57C772 7A1F0DFE 8A06B878 919AFD58

  212E475A 0346ADA6 D629BDFC AE58C42A 36D971D1 3BAB8541 EAC0AA10 919816A 1

  E22F5015 52086757 2171A4C7 6832C2BC 89ADEF72 95A81A51 0B888B1C 9EE9EE58 8E65

  quit smoking

  !

  !

  username privilege 15 password 0 xxxxx xxxxxx

  Archives

  The config log

  hidekeys

  !

  !

  crypto ISAKMP policy 1

  BA aes

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 10

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto nat keepalive 5

  !

  crypto ISAKMP client VPN-Sun-group configuration group

  key to 12345

  DNS 208.67.222.222

  pool VPN_Pool

  ACL VPN_Test

  Crypto isakmp ISAKMP_Profile_EZVPN profile

  Group of Sun-VPN-Group identity match

  list of authentication of client AUTH_VPN

  AUTHORIZE_VPN of ISAKMP authorization list.

  client configuration address respond

  Client configuration group Sun-VPN-Group

  virtual-model 1

  !

  !

  Crypto ipsec transform-set Sun-VPN aes - esp esp-sha-hmac

  !

  Profile of crypto ipsec IPSEC_Profile_EZVPN

  game of transformation-Sun-VPN

  ISAKMP_Profile_EZVPN Set isakmp-profile

  !

  !

  !

  !

  !

  !

  !

  !

  type of class-card inspect all internal match

  tcp protocol match

  udp Protocol game

  dns protocol game

  http protocol game

  https protocol game

  match icmp Protocol

  type of class-card inspect entire game Internet

  tcp protocol match

  udp Protocol game

  match icmp Protocol

  type of class-card inspect match, all the traffic-IntraNet-InterNet

  tcp protocol match

  udp Protocol game

  match icmp Protocol

  match the group-access InterNet-to-IntraNet-ACL name

  type of class-card inspect match, all the traffic-InterNet-IntraNet

  tcp protocol match

  udp Protocol game

  match icmp Protocol

  !

  !

  type of policy-card inspect InterNet-IntraNet-policy

  class type inspect traffic-IntraNet-InterNet

  inspect

  class class by default

  drop

  type of policy-card inspect IntraNet-InterNet-policy

  class type inspect traffic-InterNet-IntraNet

  inspect

  class class by default

  drop

  type of policy-card inspect sdm-policy-Internet

  class type inspect Internet

  inspect

  class class by default

  type of policy-card inspect internal sdm-policy

  class type inspect internal

  inspect

  class class by default

  drop

  !

  Security for the Internet zone

  security of the inner area

  the IntraNet zone security

  Description Interfaces all connected to the Intranet

  Security for the InterNet zone

  Description of all Interfaces connected to the Internet

  destination inner security zone-pair source sdm-zp-internal-self self

  type of service-strategy inspect sdm-policy-Internet

  zone-pair security IntraNet - InterNet source IntraNet InterNet destination

  type of service-strategy inspect IntraNet-InterNet-policy

  InterNet - IntraNet source InterNet destination IntraNet security zone-pair

  inspect the type of service-strategy InterNet-IntraNet-policy

  !

  !

  !

  !

  interface Loopback0

  IP 192.168.1.1 255.255.255.0

  !

  interface FastEthernet0/0

  Description external PPPOE Interface ETH - WAN$

  no ip address

  response to IP mask

  NAT outside IP

  IP virtual-reassembly

  automatic speed

  PPPoE enable global group

  PPPoE-client dial-pool-number 1

  No cdp enable

  !

  interface FastEthernet0/1

  switchport access vlan 10

  !

  interface FastEthernet0/2

  switchport access vlan 10

  !

  interface FastEthernet0/3

  switchport access vlan 10

  !

  interface FastEthernet0/4

  switchport access vlan 10

  !

  type of interface virtual-Template1 tunnel

  IP unnumbered Loopback0

  members of the IntraNet zone security

  source of Dialer1 tunnel

  ipv4 ipsec tunnel mode

  Tunnel IPSEC_Profile_EZVPN ipsec protection profile

  !

  interface Vlan10

  Description $FW_INSIDE$

  IP 192.168.0.3 255.255.255.0

  response to IP mask

  no ip redirection

  no ip unreachable

  IP nat inside

  IP virtual-reassembly

  members of the IntraNet zone security

  route IP cache flow

  !

  interface Dialer1

  Description $FW_OUTSIDE$

  the negotiated IP address

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP mtu 1492

  NAT outside IP

  IP virtual-reassembly

  the Member's area InterNet security

  encapsulation ppp

  IP tcp adjust-mss 1452

  Dialer pool 1

  Dialer-Group 1

  No cdp enable

  PPP authentication chap callin pap

  PPP chap hostname pty/69733

  password PPP chap 0 DSLconnect

  PPP pap sent-username pty/69733 password 0 DSLconnect

  !

  IP pool local VPN_Pool 192.168.1.30 192.168.1.40

  IP forward-Protocol ND

  IP route 0.0.0.0 0.0.0.0 Dialer1

  IP route 192.168.1.0 255.255.255.0 Dialer1

  !

  !

  IP http server

  local IP http authentication

  IP http secure server

  IP nat inside source overload map route NAT interface Dialer1

  !

  InterNet-to-IntraNet-ACL extended IP access list

  permit tcp any 192.168.0.0 0.0.0.255

  allow udp all 192.168.0.0 0.0.0.255

  allow icmp any 192.168.0.0 0.0.0.255

  refuse an entire ip

  Internet extended IP access list

  Note Internet

  Remark SDM_ACL = 2 category

  Notice all THE

  allow a full tcp

  allow a udp

  allow icmp a whole

  allow an ip

  NAT extended IP access list

  Licensing ip 192.168.0.0 0.0.0.255 any

  deny ip 192.168.0.0 0.0.0.255 192.168.1.0 0.0.0.255

  VPN_Test extended IP access list

  Licensing ip 192.168.0.0 0.0.0.255 192.168.1.0 0.0.0.255

  !

  Remark SDM_ACL category of access list 1 = 2

  access-list 1 permit 192.168.0.0 0.0.0.255

  access-list 1 permit 192.168.1.0 0.0.0.255

  Note access-list 2 = 2 SDM_ACL category

  access-list 2 allow to 192.168.1.0 0.0.0.255

  access-list 5 permit one

  access-list 10 permit 192.168.0.0 0.0.0.255

  access-list 102 deny ip 192.168.0.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 102 permit ip 192.168.0.0 0.0.0.255 any

  not run cdp

  !

  !

  !

  route NAT allowed 10 map

  corresponds to the IP NAT

  !

  !

  !

  control plan

  !

  !

  !

  !

  !

  !

  !

  !

  !

  Line con 0

  line to 0

  line vty 0 4

  exec-timeout 30 12

  privilege level 15

  Synchronous recording

  transport input telnet ssh

  !

  NTP-period clock 17208070

  NTP 17.151.16.21 Server

  end

  As I've mentioned earlier, you can of course ping from router to 192.168.0.2 because they are in the same subnet. It uses ARP instead of routing to the device when you are pinging on the same subnet.

  The switch is configured with the correct default gateway? The switch must be configured with the default gateway 192.168.0.3.

  You also mention that you can ping 192.168.0.30 which is beyond the router. This means that it is not the router VPN configuration error, but rather the terminal that you are trying to ping since you can ping 192.168.0.30.

• Create different group with VPN remote access

  Hello world

  The last time, I ve put in place a VPN for remote access to my network with ASA 5510

  I ve access to all my internal LAn helped with my VPN

  But I want to set up a vpn group in the CLI for a different group of the user who accesses the different server or a different network on my local network.

  Example: computer group - access to 10.70.5.X network

  Group consultant network - access to 10.70.10.X

  I need to know how I can do this, and if you can give me some example script to complete this

  Here is my configuration:

  ASA Version 8.0 (2)
  !
  ASA-Vidrul host name
  vidrul domain name - ao.com
  activate 8Ry2YjIyt7RRXU24 encrypted password
  names of
  DNS-guard
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  address IP X.X.X.X 255.255.255.X
  !
  interface Ethernet0/1
  nameif inside
  security-level 100
  address IP X.X.X.X 255.255.255.X
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Description Port_Device_Management
  nameif management
  security-level 99
  address IP X.X.X.X 255.255.255.X
  management only
  !
  2KFQnbNIdI.2KYOU encrypted passwd
  passive FTP mode
  DNS server-group DefaultDNS
  vidrul domain name - ao.com
  access-list 100 scope ip allow a whole
  access-list extended 100 permit icmp any any echo
  access-list extended 100 permit icmp any any echo response
  vpn-vidrul_splitTunnelAcl permit 10.70.1.0 access list standard 255.255.255.0
  vpn-vidrul_splitTunnelAcl permit 10.70.99.0 access list standard 255.255.255.0
  inside_nat0_outbound list of allowed ip extended access all 10.70.255.0 255.255.255.0
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 management
  IP local pool clientvpngroup 10.70.255.100 - 10.70.255.200 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 602.bin
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 10.70.0.0 255.255.0.0
  Access-group 100 in the interface inside
  Access-group 100 interface inside

  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  Protocol RADIUS AAA-server 10.70.99.10
  AAA authentication enable LOCAL console
  the ssh LOCAL console AAA authentication
  LOCAL AAA authorization command
  Enable http server
  http 192.168.1.2 255.255.255.255 management
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
  SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  the Encryption
  md5 hash
  Group 2
  life 86400
  Crypto isakmp nat-traversal 30
  Telnet 0.0.0.0 0.0.0.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  outside access management
  dhcpd manage 192.168.1.2 - 192.168.1.5
  dhcpd enable management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  !
  class-map inspection_default
  match default-inspection-traffic
  block-url-class of the class-map
  class-map imblock
  match any
  class-map P2P
  game port tcp eq www
  !
  !
  type of policy-card inspect dns migrated_dns_map_1
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the migrated_dns_map_1 dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  Policy-map IM_P2P
  class imblock
  class P2P
  !
  global service-policy global_policy
  vpn-vidrul group policy internal
  vpn-vidrul group policy attributes
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value vpn-vidrul_splitTunnelAcl
  value by default-field vidrul - ao.com
  test 274Y4GRAbNElaCoV of encrypted password privilege 0 username
  username admin privilege 15 encrypted password bTpUzgLxalekyhxQ
  attributes of user admin name
  Strategy-Group-VPN-vpn-vidrul
  username, password suporte zjQEaX/fm0NjEp4k encrypted privilege 15
  type tunnel-group vidrul-vpn remote access
  vpn-vidrul general-attributes tunnel-group
  address clientvpngroup pool
  Group Policy - by default-vpn-vidrul
  IPSec-vpn-vidrul tunnel group attributes
  pre-shared-key *.
  context of prompt hostname
  Cryptochecksum:d84e64c87cc5b263c84567e22400591c
  : end

  What you need to configure is to imitate the configuration on the tunnel-group and group strategy and to configure access to specific network you need.

  Currently, you have configured the following:

  vpn-vidrul group policy internal
  vpn-vidrul group policy attributes
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value vpn-vidrul_splitTunnelAcl
  value by default-field vidrul - ao.com

  type tunnel-group vidrul-vpn remote access
  vpn-vidrul general-attributes tunnel-group
  address clientvpngroup pool
  Group Policy - by default-vpn-vidrul
  IPSec-vpn-vidrul tunnel group attributes
  pre-shared-key *.

  What you need is to create new group policy and the new tunnel-group and configure the tunnel split ACL to allow access to specific access required.

  The user must then connect with the new group name and the new pre-shared key (password).

  Hope that helps.

• Customer Cisco IPSec vpn cisco ios router <>==

  Hello

  I need to implement ipsec vpn for all users of 10-15. They all use the vpn cisco 5.x client and we have a router for cisco ios at the office. We already have a situation of work for these users. However, it has become a necessity which known only devices (laptops company) are allowed to install a virtual private network.

  I think that the only way to achieve this is to use certificates. But we don't won't to buy certificates if there is a free way to implement. So my question is

  (1) what are the options I have to configure vpn ipsec, where only known devices can properly configure a vpn and all unknown devices are blocked?

  (2) if the certificate is the only way. Can I somehow produce these certificates myself using cisco router ios?

  (3) someone at - it an example of a similar installation/configuration?

  Thanks in advance.

  Kind regards

  M.

  Unfortunately if you connect to the router IOS, there is no other way except using the certificate. If you connect to a Cisco ASA firewall, then you can identify the laptop company using DAP (Dynamic Access Policy).

• What clients VPN Cisco 2811 supports?

  Is the solution of VPN Cisco 2811 locked customers cisco or that market with other brands too?

  Best regards Tommy Svensson

  Hello

  With the correct IOS feature set, it will support IPsec VPN clients. This includes not only the Cisco VPN client but almost any standard IPsec client.

  In addition, if on the 2811 can accept any browser SSL VPN connections, or even use the AnyConnect SSL client.

  It will be useful.

  Federico.

• Support VPN Cisco 881

  Hi all

  I am not cisco trained or worked with cisco, im a complete beginner in Cisco platforms. We are an IT support MPH and we have recently taken on a client that has an office abroad using a Cisco 881 device with a Draytek router to the United Kingdom. Site to site connectivity is necessary. I watched and watched videos of youtube on how to configure the VPN and think I have it in place by using the config on the cisco below:

  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  lifetime 28800
  isakmp encryption key * address *.
  !
  Crypto ipsec transform-set esp-3des esp-sha-hmac sha3des
  !
  crypto map 1 VPN ipsec-isakmp
  set peer *.
  Set transform-set sha3des
  PFS group2 Set
  match address UK

  !

  interface FastEthernet4
  IP address
  IP access-group netbios in
  IP access-group netbios on
  no ip proxy-arp
  NAT outside IP
  IP virtual-reassembly in
  no ip-cache cef route
  no ip route cache
  automatic duplex
  automatic speed
  No cdp enable
  VPN crypto card

  !
  interface Vlan1
  secondary IP address
  IP 255.255.255.0
  IP access-group netbios in
  IP access-group netbios on
  no ip proxy-arp
  IP nat inside
  IP virtual-reassembly in
  no ip-cache cef route
  no ip route cache
  !

  UK extended IP access list
  allow IP 0.0.0.255 0.0.0.255
  allow IP 0.0.0.255 0.0.0.255

  It shows the VPN and active but there is no movement between the two and I do not know why...

  Current state of the session crypto

  Interface: FastEthernet4
  The session state: UP-ACTIVE
  Peer: port of 500
  IKEv1 SA: local remote 500 500 Active
  FLOW IPSEC: ip allow /255.255.255.0 /255.255.255.0
  Active sAs: 0, origin: card crypto
  FLOW IPSEC: ip allow /255.255.255.0 /255.255.255.0
  Active sAs: 2, origin: card crypto

  So it all seems perfect, however, if I try and ping the remote remote sites over ip LAN router I get the following:

  Type to abort escape sequence.
  Send 5, 100 bytes to ICMP echoes, waiting time is 2 seconds:
  .....
  Success rate is 0% (0/5)

  I also can't ping the remote site in the Cisco lan.

  I think that it is towards the end of cisco, the Draytek is a basic router and no routing is able to be configured. It does it automatically. The VPN is so no traffic...

  Please can someone point me in the right directoin?

  Thank you

  The additional ip route does not harm even if it is not needed. I love these additional routes that they can serve as a sort of "online documentation" when it is used with a keyword "name" extra at the end.

  Your NAT - ACL does not have the traffic. Just add the following:

   ip access-list ext 102 1 deny ip  0.0.0.255  0.0.0.255 

• Installation easy vpn Cisco 871

  I have a Cisco 871 router sitting behind my adsl router and I have configured to accept vpn connections from clients from outside (partially configured by cli and partly by SDM).

  It works well, in that I can connect my LAN and access my network inside resources, however I can't access the web when connected via vpn.

  Is it perhaps to nat? I hope that someone can see why in my config. Thank you.

  Hi Chris,

  The only reason I understand here, customers lose their ability to achieve internet when connected by VPN is, according to the current configuration, all traffic (including the NetBIOS) runs through the tunnel. So when a package leaves the machine with a source of intellectual property (one of the private ip address of the pool set) of the client and the destination 4.2.2.2 (can be any ip on the internet), there is no translation defined for the ip address of the VPN client on the router.

  Thus, package from the computer of the customer with an address NON-Routable cannot access the internet for obivous reasons.

  To work around the problem, try this.

  access-list 5 by 192.168.1.0 0.0.0.255

  (assuming that 192.168.1.0 is that the VPN client subnet have access)

  Then,

  Crypto home isakmp client configuration group

  key xxxx

  ACL 5< binding="" the="" acl="">

  By creating the acl the binder to the configuration of the client, and 5 am Division of traffic in the tunnel. In other words, only for the 192.168.1.x subnet traffic will pass through the tunnel and rest will take the path of the LOCAL ISP.

  I hope this helps...!

  Concerning

  M.

• Group Lock VPN 3000 binding users to their group

  I only use a 3015 VPN with VPN Client 3.5.1 using IPSEC. Cisco ACS 3.0 is the radius, all users of the authentication server. If I use a group on the client, I can log in using a different username to groups.

  It is interesting then you get the other privileges of groups for this user as you would expect.

  If I select group Lock on core group settings is not any effect.

  I want to restrict the access of clients to the users group in its own configured.

  I use an external authentication to the Radius ACS server for groups.

  Thanks for any help you can give.

  Mark

  Hi Mark,

  You can follow the example of configuration to:

  http://www.Cisco.com/warp/public/471/altigagroup.html

  Thank you

  Jean Marc