HA advanced options default empty?

Similar Questions

• When I turn on my windows XP computer, I still get to the Windows Advanced options menu. that pressure?

  WINDOWS XP my computer came during a break current, but when I turned it back on it keeps going to the windows advanced option menu? Safe mode button is not do anything or start windows normally. Don't know what to do?

  You can select "Disable automatic restart in the event of system failure" and the next time that the system restarts, you should get the "Blue Screen of Death" (BSOD).  This will include a stop code and other diagnostic information that can help people help you here.

  (text below in italics with the permission of L elder)

  Here's a BSOD example showing information you provide:

  http://TechRepublic.com.com/i/tr/downloads/images/bsod_a.jpg

  Send for the nose and the Red arrows (3 to 4 lines total).

  Send all * line STOP message since there are clues in the 4 parameters.

  If it looks like there is some kind of name listed in the STOP message file, send this line also.

  Ignore the boring text, unless it seems important to you.  We know what a BSOD looks like, we need to know what your BSOD looks like.

  However, more than likely your system files has been corrupted by the power failure.  Use your genuine Windows XP installation CD to start the Recovery Console:
  (see http://pcsupport.about.com/od/fixtheproblem/ss/rconsole.htm)

  1. Put the CD into the computer and restart
  2. When the message "press any key to boot from the CD" press a key (if you don't see this message, you will need to enter your BIOS and set the boot order to boot from CD first) (if you don't know how to set up your BIOS, see http://pcsupport.about.com/od/fixtheproblem/ss/bootorderchange.htm)
  3. Once the files load from the CD, press R to enter the Recovery Console
  4. You can get about choosing an installation; the usual answer is C:\Windows
  5. If you have set a password for the 'Administrator' account, enter it now; the default is blank (no password)

  At the command prompt (C:\Windows >) type the following and press enter

  CHKDSK c: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

  If you don't actually have a real Windows XP installation CD, you got nothing to worry about.  Follow the instructions of the elder s below:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget what you have (no XP media required).
  

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.
  

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

  Unfortunately, I'll be away from my computer for the next 2 or 3 days... then if the above does not help, and that no one else jumps, have patience.
  

• HP ENVY 4500 all-in-one: ENVY 4500 advance Options

  How to add or remove in the menu the paper size set in the Advanced Options screen?

  Hello

  You cannot delete but you can add custom formats. This can change when you change your computer, change OS, re - install the driver. Printer driver keep his list by default only.

  Kind regards.

• Airport Utility iOS advanced options disappear

  This morning, I noticed that my AU on iOS has none of the advanced options. The option restart also disappeared. There are two changes that have taken place:

  1) instituted by domain controller of origin with AD, DNS, and DHCP. Always had advanced options immediately after and was able to restart remotely HQ Airport Extreme.

  (2) upgraded to iOS 9.2. Did not consider new utility until AFTER the update.

  Basically everything I have now is the following:

  Base station > name and password

  Network > wifi ssid and password

  network invited

  Internet connection > ip and dns settings

  all other parameters have completely disappeared on ipad and iphone. Note that are present on mac os x (10.11.2) and have not changed. All others this experience or comments?

  The answer came. It's a bit delayed by protesting, but apparently if you provide a domain, DHCP and DNS internal controller, these options are not available. As soon as I stop the server, default DNS settings my ISP and open the DHCP range, everything is back. Pain during the execution of some servers, but at least I know now.

• Installation of earlier versions of CC, where can I find the "advanced options"?

  Hi, where can I find the "advanced options" to do this:

  By default, when you install a new application of Creative Cloud 2015 it removes previous versions of the application on your computer. If you want to keep your old version installed, click Advanced Options , and uncheck the box delete older versions in the update confirmation dialog box.

  I can't find anywhere, thank you.

  Hi Warris,

  Please refer to the "Update of Apps" section of this document:Update Adobe Creative Cloud 2015 applications

  You can also see before you upgrade to creative cloud 2015

  Hope that helps!

  Kind regards

  Sheena

• Purpose of Converter PDF Adobe Advanced Options

  I am curious about the purpose of the " Advanced Options " (also called " Advanced Document Settings " "") for the Adobe PDF virtual printer.  For example access from an application via

  Print(.. . Select Adobe PDF as printer) > Properties > Layout > Advanced .

  I've included a screenshot for clarity.

  Options include the Paper Size .  Above all, I am interested in the creation of PDF to MS Word documents, and the layout in Word would negate the Paper Size option, I'm pretty sure.

  There is an option for Print Quality .  But the joboptions files (profiles accessed via ... > Properties > Adobe PDF Settings > Default Settings/Edit ) seem to control the ultimate resolution output printing.

  There is an option for PostScript Output Option , with possible selections including " Optimize for Portability "and" Archive Format ". ""  I'm interested in the PDF/A output, but these two evocative PostScript options appear only useful if the postscript file was going to be created/used/manipulated.  It seems that nowadays the postscript file is not usually explicitly created, but serves as a 'hidden' intermediate in the creation of the PDF file.  See also http://www.freeframers.org/archive/01/msg00050.html

  Am I right to conclude that the 'Advanced' options are a feature inherited , not useful to anyone who creates PDF files in a single step - instead of printing to a file in postscript format, followed by the creation of PDF files using the Distiller?

  See for example http://forums.Adobe.com/message/1240330#1240330

  Kind regards

  DIV

  I pretty much agree. However, the print quality may be a great. I use 300 dpi and a lot of people recommend 600 dpi. The 1200 dpi is well beyond what is normally required. A place where the 1200 is a major problem is in preparation of slides in PDF format. If you have drawn with lines of 1 pixel color, they will be 1200 dpi. Imagine the problems when viewing on a 96 dpi screen, a factor of more than 12 less pixels. A yellow line 1 pixel is almost unreadable because of the way the line is sampled for display. If 300 dpi is used for print quality, then there is no problem. I found this one on the hard.

  Most of the other settings let you alone, or change somewhere else.

  In your example of another post DOC file, your A4 came out as a letter for me. The paper defined in the DOC file is A4. My default in Acrobat's letter. Thus, the WORD does NOT replace the printer setting. You must set the paper in the printer separately, similar to the right paper in the printer.

  I'm still struggling with all the differences that you are trying to report on your other post. There are differences, but I am not sure of the reason. You might want to look at a page in the PDF document audit optimize see were the resources are used.

• I imported my address books. How can I remove the default empty

  I imported my address from my old computer books in Thunderbird on my new computer. Empty default address books don't seem to be able to be deleted, so I have now two books personal address and two collected addresses, the first of all is the default value for empty one and the second is my populated version. Thunderbird seems to point to the default empty. How can I remove the empty for default Thunderbird to my places.

  Thank you

  I don't think you can remove the default books. I open any personal book, select a contact, do a control + a to select all and drag in the personal address book by default. Then delete the empty book. Then do the same for the collected books.

• UNMOUNTABLE_BOOT_VOLUME error - I get this on a "blue screen" page, and the only other page that I see is the display advanced options. None of the items I selected in this list nothing do for me.

  I can't get past the blue screen on my PC.  I tried to reinstall the system, but all I get is blue screen as described above with the "unmountable_boot_volume" error or the display advanced options when I restart my pc and press F8 immediately.  I tried each of the options on the screen advanced options, nothing happens.  Can anyone help?  Thank you!

  Hi Debbie,.

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?

  See the Microsoft article and try the steps mentioned, check if it helps.

  When you restart your computer or upgrade to Windows XP, you receive the error message "STOP 0x000000ED UNMOUNTABLE_BOOT_VOLUME".

  http://support.Microsoft.com/kb/297185

• In the Advanced Options Menu that I used to have a last good known Configuration to select who is gone?

  A while back I had to have my hard drive formatted and windows re-installed.  Advanced options, used to have a selection for the last good known Configuration. This selection is no longer there, but the other options as the safe mode and Boot normally.  This was a result of the hard drive being formatted? I'm more worried if this indicates a problem with the hard drive?

  I've since upgraded to Windows XP, which has the system restore, so I don't know if the last known Configuration Option is necessary.

  Let me be frank.

  This system is an old Windows 2000 upgraded to XP and it is low on RAM (384 MB) and low processor speed ~ 977 Mhz.

  If you are thinking about replacing/upgrading, it would be a wise investment.

  I know how to get emotionally attached to an older system, but one day you just I have to bite the bullet and get something more modern.

  You may he likes not at first and can hate him, but with some time and when you get your new system composed with your exact settings you like, you'll start to it.

  I've got 6 systems here who have bitten the teeth and never before seen power in months, but I can donate or use parts for someone who's biggest thrill in the world and what brings him smile in their face is playing Solitaire on a computer (or a visit to a dog... it's what I do sometimes).

  If you have problems with XP, I can help you with this better than I can, but your system specs are barely minimum for a good system in XP.  You could probably make it work, but it often curse you that you operate.

  That's just my opinion by observation.

• F8 key does not have the advanced option!

  CS_SystemLabel

  XPS 15 (9530, end of 2013)

  CS_OperatingSystem

  Windows 8

  I want to do a factory reset and return to the first configuration of my Dell XPS, but when I click F8, it won't go to advanced options, as it normally should, I clicked several times on the F8 key before and after and and each time, but it never shows the advanced options should be , can help you on this? Thank you

  yorlink

  I managed as well to recover my product key OEM Windows 8.1 :)

  Now, I've left two questions:

  (1) why the F8 key does not work as it should!

  (2) where the recovery partition? I mean I say I format the C: / drive, I'll still be able to save the factory OS or this partition is located in another hidden partition?

  In fact my XPS is still under warranty, but when I contacted DELL support they told me by email that they are not able to call me because the PC was purchased from the United Kingdom and that I am not located in the United Kingdom they call me not, turn on! and after that, I asked just for the answers to my questions, but they still didn't have answer,

  Just don't call it premium support because it is not

  1. the UEFI BIOS and SecureBoot so that the change in the way Windows 8.1 boots. So that the 8.1 Windows start faster than Windows 7, there is almost no time for the user to type F8. This method to access boot options is obsolete as Windows 8.1 simply boots to fast.

  To get started, hold the SHIFT key while rebooting. Please see here for more details:

  https://www.YouTube.com/watch?v=fqqgk2fOtGU&index=5&list=PL1RkaknDn7v88-b9HVWAauoWSHDQhoe4w

  2. the recovery partition resides on the same hard drive as a partition unlabelled. Check out this guide here, when I was testing Dell Backup and Recovery on a clean install using the version 1.7.1.2:

  https://www.YouTube.com/watch?v=xKJjg0VAkIQ&list=PL1RkaknDn7v88-b9HVWAauoWSHDQhoe4w&index=1

  Should not be in this version that the recovery partition has been labeled and this has been fixed in version 1.7.5.64.

• Dell Inspiron 531 - summer pc try to restore factory settings and hit the F8 key after close to a dozen times. I never see the advanced options to choose the factory restore. HELP please...

  tried to restore factory settings and hit the F8 key after close to a dozen times.  I never see the advanced options to choose the factory restore.   HELP please...  I'm following indications out of Dell's web site as well.    UGH

  http://support.Dell.com/support/topics/global.aspx/support/DellCare/contact_us?c=us&l=en&s=Gen&redirect=1

  If you have problems with the process of recovery of Dell, contact Dell at the link above.

  It's Dell recovery, not Microsoft software/process of.

  See you soon.

  Mick Murphy - Microsoft partner

• Application not shown in Options-> Advanced Options-> Applications

  Hello

  I developed an application that runs in the background, but this request is in the Options-> advanced-> Applications. I wanted to change the permission so that it do not ask for confirmation of sending sms. Can someone let me know why he is not coming to this place. While another application that also runs in the background comes from the Options-> Advanced Options-> Applications, but not the second request.

  We hope to get an answer soon.

  Thank you & best regards

  Sunil

  Load file jad in the device rather than cod using javaloader.

  1. copy your cod and jad file in bin JDE (ex: C:\Program Research In Motion\BlackBerry JDE 4.6.0\bin\).

  2. run the following command from there (you can create a batch file (* .bat) and just click)

  JavaLoader - usb charge applicationName.jad

  Concerning

  Bika

• Lack of Options > Advanced Options > Applications entry for the application of Simulator test

  I'm new to BlackBerry dev and I'm still doing my set up and tested development env.

  EPS consists of XP, Eclipse SDK 3.4.1 BlackBerry JDE plugin for Eclipse 1.0.0.67, BlackBerry component Pack 4.3.0.16 version 4.3.0 and the BlackBerry 8120 Simulator.

  I created a test application simple and loaded on the Simulator for testing through the cmd Eclipse Run > run as > Blackberry Simulator.  As expected, the application icon was displayed on the screen of the Applications (in the Simulator), and, when selected, the application has successfully launched and behaved normally.  So far so good.

  However, when I checked the Options > Advanced Options > Applications on the Simulator, I found that my request was not among others installed apps.  (I tried on two other simulators with the same results.)  I thought about reading the other posts on this forum that I would wait to see this information.   When I install on a simulator I would indeed expect display name information and the app version contained in Options > Advanced Options > Applications list?  If Yes, what should I do to make the information appear?

  Thank you.

  If you install your app in the Simulator simply by copying the COD file in directory of the Simulator (what is JDE when you run Debug), then you should not wait for the application to create. The modules in the files of the cod will be stil it well and that's all that generally the County. You can see the list of modules under Options-> Advanced Options-> Applications-> (Menu)-> Modules. Applications that are included in the Options-> advanced-> Applications are just constructions of metadata on top of modules to simplify various tasks, like setting permissions, adding and removing applications rather than tracking dependencies and individual modules.

  PS, You can programmatically create the entries in the application using the CodeModuleGroupManager and CodeModuleGroup if you really must have your request under Applications. Do not however forget that classic pose methods (Desktop Manager, Web OTA Download, BES OTA Push) all create them the entries in the appropriate application. So, you don't usually have to worry about this problem in the production environment.

• Options-> Advanced Options-> question of PTC

  Hi guys.

  I certify on the TCP parameters.

  You know that BB has options for TCP (Settings / Options-> Advanced Options-> TCP: "APN", "APN username" and "Password for APN").

  Can I connect via HttpConnection without any configuration (without suffix: ";) APN = wap.cingular; tunnelauthusername = user; tunnelauthpassword = password'), when the user set above parameters such as "APN is wap.cingular", "[email protected] username" and "password for APN = cingular1?

  In other words, if the user set Options / settings-> Advanced Options-> TCP, I must determine '; APN = wap.cingular; tunnelauthusername = user; tunnelauthpassword = password '.

  Is this good?

  If the user has not indicated the Options / settings-> Advanced Options-> TCP, I need set up: «;» APN = wap.cingular; tunnelauthusername = user; tunnelauthpassword = password '.

  Is this good?

  Thank you.

  Your interpretation is correct.  The TCP (not PTC) options are used only if there is no value specified in the connection URL.

  Not that different carriers may have different requirements, for example, I understand Verizon don't require any setting at all for deviceside = true for work.

• BlackBerry smartphones 'Advanced Options' lack of OPTIONS. HELP PLZ

  By clicking on the home screen Options, does not show the menu 'advanced options' item. He has been there nut has now disappeared. "It was" the last menu item in the option, but now the last of them is "third-party Applications.

  In order under Options in the list is the following:

  1 sounds and ringtones

  2 network connections

  3. the screen

  4 typing and entry

  5 device

  6. call management

  7 security

  8 accessibility

  9. third party Applications

  Where is ADVANCED OPTIONS? !!!

  What you have stated, what offers the torch.  You can refer to an older o/s.

  To access advanced options, you have to go to Options > device > advanced system settings.