hardware-software of Dvd 7020ct does not

Similar Questions

• Error message: "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged" and dvd burner does not

  Original title: dvd burner does not work can not load the driver

  I get this message "windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged.

  Can someone help me?

  Hi Garry_x,

  1. were you able to use the DVD burner before with no problems?

  2. you remember to make changes to the computer recently?

  This can occur when more than one service is defined for a device, if there is a failure at the opening of the service registry entry, or if the driver name cannot be obtained from the service registry entry.

  You can check out the following link and check for the resolution:

  http://TechNet.Microsoft.com/en-us/library/cc772156 (WS.10) .aspx

  You can also read the following article and check if it helps:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Hope this information is useful.

• I have PC toshiba laptop, my cd/dvd. writer does not read the CD software and not able to write the media__

  itshow msg

  Insert the disc pls

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  ===============================================================

  Check with Toshiba support, their drivers online (update or reinstall) and their forums.

  Toshiba - Forums
  http://laptopforums.Toshiba.com/

  Toshiba - Contacts
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contact

  Toshiba - drivers - access your model
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download

  Toshiba - Support
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• CD/DVD drive does not work after 8 Win instalation

  Since a month since I've updated my windows in windows 8, everything works fine but the DVD - RW.

  When I put the blank cd and try to open it, it gives me error when opening by saying:
  "windows could not complete the format".

  Who's a software or a hardware problem?

  waiting for help!

  This means that your CD/DVD drive no longer works and is not recognized by the system?

  If Yes, then I would recommend checking this Toshiba document that I found on the portal of the knowledge base site:

  + Why my CD/DVD drive does not work after upgrade to Windows 8? +
  http://APS2.toshiba-tro.de/KB0/FAQ2B03F10002R01.htm

  You must uninstall the programs from Toshiba:
  TOSHIBA Recovery Media Creator
  TOSHIBA Disc Creator

• Satellite A200 - 23P - mechanic of DVD - rom does not

  I'm sorry for my English in advance this topic! -Thank you

  I have a very big problem with my engraver of DVD (RM).
  I bought SAT A200 - 23P three weeks ago.
  The Win VISTA operating system has been installed. DVD - rom worked well.

  If I have installed Win XP to the second partition on my HARD drive (to install the disk with driver for sata drive in nlite) and installed all the drivers and utilities for Toshiba laptop, I found that my DVD-rom is not working while I press eject button.

  Mechanic of DVD is not responding to eject in XP and not even in the BIOS!
  It is interesting, mechanic DVD is the detection in BIOS, detects in XP, XP operating system votes - mechanic to the DVD works properly - its fable.

  However, if I have installed XP on the second partition, Win Vista does not load :(
  I don't have a second chance for second selection (Vista and XP).
  I now have XP only, even if Vista is on the first partition - I didn't delete it.

  Do you think that the DVD-rom is HW or SW problem?
  I think that, given that the DVD-rom does not in the BIOS - HW error.

  But is very strange, if I install XP from mechanic to the DVD and then close is, DVD - rom does not...:)

  If I manually open and insert the CD, the DVD does not (diode led no blink, just if I turn off the computer, led blinked once).

  PLS help me someone-

  Thank you!

  Hi Michal

  Your question is very strange, I mean the number of CD/DVD drive

  The fact is that the readers of CD/DVD eject function functions should any operating system has been installed on your laptop. It has nothing to do with your software on the HARD drive.

  So I wonder why the eject button works with Vista and not XP preinstalled OS?  :|

  My only plausible explanation is that sometimes there is a bad connection between the laptop and the drive. However the problem could be related to the hardware problem too

  As you see it s not easy to say what's wrong exactly, we can only speculate.

  Now some details about your installation of OS double.

  You cannot choose between Windows XP and Vista because Vista boot manager was obliterated during the installation of Win XP.
  This happened to me also. I installed Win XP on my Satellite and could not start Vista.

  The solution was simple; I used another original DVD of Vista (from my friend) and booted from this DVD. Vista has renewed the Boot Manager, and then I was able to boot Vista.

  Then I downloaded the tool called Easy BCD.
  This tool can change the Vista Boot Manager settings. I've edited and inserted a new Windwos XP OS entry.

  That s it!

• My DVD drive does not recognize DVD game discs.

  My NEC ND-4550-reader DVD - RW does not recognize DVD game discs.
  He has no problem reading movie DVDs and music CDs or access data CD and DVD burnt with data on them.
  I removed and let XP Reinstall the device and high-low filters removed the registry etc nothing works.
  I made a copy of a DVD game on another PC and it is recognized and install my PC.
  All DVD discs work very well on the other PC.
  I am running Windows XP Professional with SP2.
  MS Fixit controls indicate no problems.
  This would be a matter of software protection?
  All tried game DVDs are official records and not copies.
  The NEC ND-4550 uses cdrom.sys as pilot.

  Finally, I replaced the drive for a new one (Pioneer DVR-S18L) and everything now works as it should.
  So I suspect that it's a hardware problem and not one that can be resolved by any of the Windows settings.

• My Dell Desk Top DVD Player does not work. Whenever I have insert the disc and click here to read... I get the message insert' disc Please "."

  What is the faulty drive, or the software that is missing

  Hello

  What happens if you close all programs and then insert the disc?

  -------------------------------------------------------------------------

  If you have problems with CD/DVD drive:

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• I have a computer running VISTA. The CD-ROM/DVD-rom does not work and can not read the CD of the program that I placed in it.

  It won't read a DVD.  It will not read ANY CD or DVD.  I tried 12 different CD/DVD.  This isn't an upgrade to Vista; the computer came "made for Vista" with Vista installed on it.  I had added Nero.  I removed Nero.  I did all the updates. I have not released the driver and reinstalled.  He claims to have the latest driver software, but it won't work.  The computer can see the CD/DVD, but he calls it a 'CDROM '.  It is not the case.  It is a DVD/Cd-RW with Labelflash.

  I did everything suggested that past discussions.  I ran FIXIT program that claims that the drive works properly.  It is not the case.

  I tried to get various programs to recognize.  They cannot see the installed media.

  I uninstalled iTunes.

  Please do not give me the answer of cut-and - paste stock; It does not work.

  Please tell me what to do to make Vista see the media inserted in the CD/DVD-RW drive.

  Thank you.

  Hello

  Well, if you have tried all the usual bugs try this:

  Make a Restore Point:

  How to create a Vista System Restore Point
  http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
  ------------------------------------------------

  Then go to right click on UNINSTALL - - CD/DVD - Device Manager CHECK THE DRIVERS to REMOVE and
  continue.

  Reset.

  Occasionally, install an upgrade or a re - install will fix the problem and of course the drive or other hardware issues
  could be at stake.

  =====================================

  Here's the answer, just in case there is something you don't have, and I start up and down.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable
  or slight corrosion on the contacts (usually for a laptop) and other issues.
  

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===========================================

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation (if all goes well
  saves the data, and you need to reinstall the programs). Be sure to do a good backup or three.

  You can use another DVD that are not protected but you will need to copy you have the product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can make a repair facility that must save the data but you will need to
  Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• CD-ROM/DVD-ROM does not.

  Driver software has had a problem when he tried to run. Code 39 problem.

  Hello

  Code 39 means that the driver is corrupted or missing.

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  --------------------------------------------------------------

  Also check with your system manufacturer to see if there are any updated drivers for your DVD. Or even if it
  are you can reinstall the 'old'. Many use Windows default drivers however some special aura
  ones. Also check the website of the manufacturer of the car.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Hope these helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• My CD-ROM/DVD-ROM does not work

  My CD-ROM/DVD-ROM does not work.  Manager of devices display a "!" on the Optiarc DVD RW AD - 756 A ATA DEVICE.
  1 device state poster (this device cannot start. (code 10)).
  2 update driver... shows that the best device driver software is already installed.
  3. it is the driver of manufacturing.
  4. I tried the microsoft fix it downloads and it has not solved the problem.

  Hope that enough information... Oh, my computer is computer laptop HP Pavilion G60-231Wm.

  Grateful for any advice...

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Re: CD/DVD drive does not seem to start the DVD in Satellite P750

  My CD/DVD drive does not seem to start DVD, it runs and runs and the only way I can run a DVD (i.e. film) is using Windows Media Center, while the software to install must be enabled in Windows Explorer.

  Anyone?

  Help, please.
  Thank you!

  Have you tried to change AutoPlay settings?
  Open Control Panel and Auto game options. Enable the option Use AutoPlay for all media and devices. Also change other options, especially for DVD movies, software and games.

• Mat * one years (uj-840) DVD player does not work properly

  The Mat * one years (uj-840) DVD player does not work properly.
  A symptom of the problem is that the icon does not appear in 'my computer '.
  more and she does not recognize the CD.

  I went to the properties of the drive through Device Manager and saw the following message is displayed:

  "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)
  Click Troubleshoot to start the troubleshooter for this device. »

  Following the instruction of the troubleshooter, I tried to update my driver through
  Device Manager, but it tells me that the current driver is the more up-to-date version.
  In the properties of the drive, I found that my driver version is: 5.1.2535.0

  What is a simple problem that has a solution?
  I don't see other actions to find the root of the problem.

  Thank you

  I hope this article can help you - http://aps2.toshiba-tro.de/kb0/FAQ8101LA0000R01.htm
  Check it out!

• DVD player does not accept disks

  My '' integrated '' DVD player does not read the disc (DVD, BluRay, any region code), but it ejects after a small delay of about 1 to 2 minutes.  Is there a diagnostic software to find the problem?

  Your Super Drive never read blu ray and probably did not. Try a cleaning disc. Try resetting the memory NVRAM How to reset NVRAM on your Mac - Apple Support and SMC reset management system (SCM) controller on your Mac - Apple Support

  Finally buy and inexpensive external optical drive, but not apples Super USB drive because it does not work with your Mac.

• Satellite A200 - 19L: no sound after hibernation & CD/DVD drive does not work

  First of all, my laptop computer became very slow loading vista after formula 1 week to buy it.

  Second, sometimes when I put the mode 'sleep' a revival of the laptop, there is no sound and a red circle appears over the speaker icon in the bar of tasks, and when I go into control panel > Sound, he tells me that no. his drive was installed and when restarting the laptop the problem resolved?

  Thirdly, after the formula of the week 3 buy the computer also dvd - cd player has the same problem, like the sound and when you open my computer that NO cd\dvd drive icon and when I put a cd or dvd, it does not work or run and it happens all the time, even if the laptop restarts.

  Since then im able to watch movies or work.

  I'm lost and I don't know what to do!
  (Sorry for my bad English, but I hope you understand the problems)

  Hey Osama

  I think I can help you. The questions that appear on your laptop are not serious and the only one associated with software or registry.

  Regarding your noise problem:
  Please check this Microsoft document
  http://support.Microsoft.com/kb/929685/en-us
  or
  http://support.Microsoft.com/kb/937077/

  the MS update must be downloaded and installed ;)

  Regarding the missing CD/DVD drive;
  I think you should try to remove the drive from Device Manager and reboot the laptop. Then the operating system should recognize the STRANGE again.
  Secondly you should access the registry editor and should remove the upper filter and bring back the key filter
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  Recommend checking out:
  http://support.Microsoft.com/kb/270008/en-us

  best regards and I hope that I can help you

• DVD writer does not recognize 'NEW' blank DVD - r (Windows XP)

  Hello

  I have a question that has been annoying me a lot during the last few weeks, as follows...

  I have a Dell Optiplex GX620 computer is running Windows XP service pack 3, it has a cd/DVD burner in this model (HL-DT-ST DVD +-RW GWA4164B), I used to be able to burn CDs and DVDs fine, so please respond with lol 'maybe your drive doesn't burn DVDs' as you can see in the model # it's a DVD +-RW drive.

  But my problem is the following... for some reason the DVD burner does not detect the 'NEW' blank DVD - R, there is no problem of detection of blank CD - R disc and I can burn fine on the CD - R. But for some reason it does not detect blank DVD?

  When I put one in the drive, I don't get the popup asking what I want to do etc, or to go to WORKSTATION and look a the drive it shows no media present.

  I have Nero Platinum 15 installed in my burning software, which has a function of DISK INFORMATION, which also shows that 'no disk in drive '.

  I have re installed Nero...

  I uninstalled the drive and re installed

  Re, I installed the latest drivers for Dell Optiplex

  I bought a second axis of new blank DVDs

  I took out what I left little hair!

  Can someone provide me with a fix for this problem? ANY help is GREATLY appreciated guys!

  Hello

  See if that helps you.

  There is a "Fix - it" Microsoft for your problem on this link

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  If above doesn't fix it, continue with the help of Microsoft:

  http://support.Microsoft.com/kb/982116/en-us

  See you soon.