Similar Questions

• Problems of heat with Satellite M70-173

  Need some advice.
  Have in last few weeks found that all side and sometimes in the middle of the laptop its got very hot to the touch.
  Have no idea what could cause this?

  Hi mate,

  I think it could be a cooling system that is full of dust. If the cooling system is clogged with dust and then the machine cannot carry enough heat of your machine which has been generated by the processor and graphics card. The result of this could be overheating, software errors and finish hardware malfunction.

  So, my advice to you: go to the next radio Shack or electronic market and buy a box with compressed air. Some blowing AIR gently hollow the vents and if dust comes out then you know where the problem is. Just clean the entire cooling system and make sure the cooling system is almost free of dust.

  Welcome them

• Heating with G motorcycle problems

  I am facing heating problems with my motorcycle G... The phone becomes heat immediately using the WiFi also? Help me avoid this problem... I contacted the customer Service... They checked my phone and said that no hardware problem and they re installed OS too... But I am facing this problem... Help me

  
  

• ENVY of HP dv7 - 7398ca: heat with two hard drives problem?

  I have a HP ENVY dv7 - 7398ca. The original hard drive crashed. I replaced it with a Kingston SS drive and plan to add a second drive slave 1 TB.

   

  My question is, the stock fan will be able to handle the heat of two hard disks.

   

  Thanks for any response.

  Hello

  Should be ok. The machine is designed to manage two HDD mechanical (or normal).

  Kind regards

• Problems of heat with the mid-2015 MacBook Pro 15-inch with retina display

  MacBook Pro (retina, 15 inch, mid-2015). 2.2 GHz Intel Core i7 | OS X El Capitan (10.11.3) | 16 GB 1600 MHz DDR3 | Intel Pro Iris 1536 MB | 251 GB of Flash storage

  My 2006 13 "MacBook White would get really hot on my knees if I was using the DVD player.

  Since then, my new MacBook Pro has no disc hard turns and no great, should I feel any heat at all?

  There is an old rule to never put your laptop on your lap, because it may damage your skin. I wonder if the new MacBook Pro will become warmer over time, or if I can expect to not feel high heat.

  Is there a range?

  I did have the machine long enough to say that I have done the troubleshooting steps.

  The DVD player is not the primary heat generator, the CPU/GPU are the creators of the heat.  When you use resources intensive applications, you can expect your MBP become very hot.  Video, Skype, games, etc., are applications that will make the CPU/GPU heat, reaching temperatures in the range of 90 ° c.

  You should expect at a temperature between 40 ° c to 50 ° c when running during 'normal' light applications such as text editing and browsing the web.

  Ciao.

• Mac Mini heating disinformation

  Yesterday (June 11, 2016) I talked about Apple Support via their phone an overheating problem, I lived with my Mac Min 2.5 GHz Intel Core i5 4 GB 1600 MHz DDR3.  I have described the symptoms and asked if Apple had problems of heating with the Mac Mini. Their 'expert', said that they had not.  It helped me to run a program of self-diagnostics of material that showed no problems.  (Off, press and hold the "D" key and then turn on the Mac Mini, while pressing the down D until the diagnostic routine displays.) No problems have been found and my machine has not overheated since.  But I learned by following a search that there had been several previous Mac Mini heating problems and Apple was aware that a lot of their products and have experienced similar problems in the past.

  Some users have problems and do not see a lot of these problems here. It what Apple said is true; There is no real history of such problems.

  How are judge you overheating?

  If you have installed a speed temp and fan, monitor applications that this exhibition?

  I use Mac Fan Control.

• Problems with my timed State machien

  Hi all

  The project

  I'm trying to create a timed state machine that can scroll through a series of cooling-then-heating cycles, where every cold or heat function occurs during a specific period of time.
  For example, if I set the number of cycles to 20 cycles 'cool-then-heat', with a cool cycle lasts 10 seconds and a cycle of prolonged heat of 10 seconds, the program will run for 400 seconds and then stops.

  After initialization, a clock will start. In the cool loop, there will be a cool clock which is compared to all of the cool cycle time. If they are equal, continuous cooling, noto, if they are equal the progresses of program in a heat cycle.

  The cycle has estrogen to a clock of heat that will be compared to the heat set duration of the cycle. If hot clocks are not equal, heating continues, if they are equal the cycle estrogen is complete and the product is finished or running in another round of cool.

  Another round of cool is selected if the elapsed time (since the State apparatus has been initialized) matches both total managed program (i.e. the total length = 400 seconds).

  (I've also attached a drawing that explains the process I want schematically the state machine).

  The problem

  I have a few, but the first is I think I use the block of bad timing - in my VI, the clock of the tick is not starting from scratch when I press run. It is included in a while loop as I have reason to think it will be easier to run (for the computer) if I put a delay (without delay the state machine functions). Rather than from

  I have a small calculator that determines how long will be the run time in total (this value is compared to the length of time since the entry into force).

  If anyone no matter what other tasks that help sadjusting need me know - I'm very new to labview and want to pick up good practices on the way!

  There is also the express VI "out of time", you could use.

• Adding a GIGABYTE 660 OC will void my warranty? Problems of heat?

  Hi - I wait tomorrow my new 8700 XPS and wonders if the addition of this card will void the warranty? I don't see it on the list of cards approved, although I saw some 660 s

  Gigabyte GeForce GTX 660 OC 2GB

  www.amazon.com/.../B00942TK8I

  I was also wondering if there will be problems of heat with long game several hours a day. (e.g. Skyrim/Assassin Creed/Dragon Age Inquisition)?

  I'll upgrade later from the PSU and video card, assuming the case is pretty cool - I have a Coolermaster EVO that I doubt will fit.

  Any other advice on installation? I don't know if the update of the Bios is required for this card.

  Anyway, thanks in advance.

  warranty shouldn't be a problem. Older GPU do not need an update of the BIOS, most recent need of revision of the A10.

  Here's a whole thread discussing what you plan.

  http://en.community.Dell.com/support-forums/desktop/f/3515/t/19611037

  I don't come by that much money on a 660 GTX when more recent, better, faster cards is available for less money, that draw less energy and generate less heat.

  A GTX 960 will well on skyrim and OK on Assassin creed.

  A GTX 970 will be much better, but the OEM PSU is at the limit

  Cooling is not bad at all, just make sure that the case has a lot of airflow around it.

• Pavilion dv6-3225dx: laptop is heated

  Hello

  I have a pavilion dv6-3225dx notebook PC. I am facing problems of heat with it. The laptop gets very hot normal temperatures after starting or after waking up after fashion 'sleep'. The fan runs continuously for a long time. When executing, there are distortions in the speakers. I showed it to a hp service center and they have replaced the fan. I also cleaned. The problem still persists. I read on the hp site which may help to update the BIOS. Must iupdate BIOS? This will help?

  Hello

  Yes, we recommend you update to the latest version of the bios

  Please find the link to download the latest version of the bios

  http://ftp.HP.com/pub/SoftPaq/sp55001-55500/sp55299.exe

  ====================================================

  Although I am an employee of HP, I speak for myself and not for HP. ===

  * Click on the star of CONGRATULATIONS on the left say "thank you."

• heat Pavillion m6 problem

  I recently got this laptop and when I light on the laptop from the left side navigation where are my Palms gets hot enough. I wanted to know if this is normal or if it's just my phone, I thought that most of the laptops try to keep this part also just so fresh as possible I wanted to see if I just get a new m6.

  I have the 1045dx of m6 and present the same problem.  The left palm rest gets a lot hotter as I wait, especially considering that I have "HP Coolsense" on.  I know by looking at the service manual the graphics pricessor is located in this area, and I suspect that it is the source of heat. I already have one of these in returned because the telescope was assembled incorrectly and was pressing the screen when I push on the lid, leading to the ripple in the lower corners.  I used this one for a week or two before I Exchange it there and never noticed this problem of heat with it.  Maybe that I was just distracted by default and was not paying attention to the temperature... I do not know.  I know that this machine also has the construction problems. Sewing around the edge before where the metal meets the side plastic has a significant gap on one side and the plasitc edge tilts on somewhat between the screws at the front and two corners do not fit properly. Overall, the quality of external construction of this machine has me concerned about the internal assembilies.  I would not be surprised if they do not have a thermal pad or fat on the radiator of the graphics processor.  I really think that HP should hire a better class of sweat shop for the manufacture of machines here!  A couple of years, I went through 3 models of DM4 before I found one that had no obvious defects.  I love the drawings of HP, but their quality control, especially with one of their models metal STINKS!  I'll probably take this one to get a refund back this time and buy something else.  I guess I give up on HP.

• Pavilion G6 2004tx graphics...

  Hello

  I baught my laptop (HP Pavilion G6 2004tx) on August 16, 2012.

  Configuration:

  OS: Windows 7 HB.

  CPU: i5 of 2nd generation.

  RAM: 4 GB of DDR3 memory

  GPU: 2 GB DDR3 - AMD Radeon HD M 7670

  HARD drive: 500 GB

  I have a few questions related to the graphics hardware in the laptop,

  How will I know that running ongoing game, uses only materials 'Radeon HD 7670 M or Intel HD'?

  or isther any way to keep the hardware default "Radeon HD 7670 M '?

  Maybe the wrong question...

  Reason for asking this, when I run games HD on laptop, my laptop computer fan spins too fast. is there any problem of heating with this model?

  These days are very much like its winter here, but the worry about the summer m.

  What should I do?

  Thank you

  Darshan

  With high-performance graphics card activated and play games that are moderately high demanding will cause the fan turn quickly enough to compensate for the extra heat. This is especially true for laptops that have other components of end superiors such as the processor.

  On most laptops, you can check what card is activated by right-clicking on the desktop and selecting Switchable Graphics. Here, it should show if the performance or energy savings card is activated. If bad one is enabled, then you should be able select one you want to have allowed here as well.

  Most of the laptops with switchable graphics will auto switch between them based on whether or not the power supply cord is connected like the Radeon will use more power. It should be an option to disable this feature on the switchable graphic display configure as well.

  Some laptops support dynamic switching depending on the application being used, but these are few in number.

  Let me know if this answers your questions.

• 5s iPhone won't turn on after hours of load

  Hello apple community, I hope someone can clarify this for me!

  My iphone 5s or 16 GB (iOS 9.3.1) is 18 months and worked perfectly up until 2 months ago when he would go dead and would not turn on unless I heat the back with a hair dryer.

  The first time, she was cut off, I kept it plugged in for more than 12 hours on a charge unanswered, then I discovered in a forum should I heat with a hair dryer. I did it and it worked, after a minute of heat, apple logo finally appeared. I did it in 3 different occasions where the battery went completely empty and it worked!

  However, the battery died again yesterday and I have heat in the back 3 times. On the 3rd time, iphone finally turned on but the battery level maintained at 1% and it does not reach the same load, while implementing the alarm, the phone has been cut off again and nothing happened since then (he was 18 hours without my phone). You think it's time to replace the battery? IS THERE anything I can do to make it work again, I promise that I won't it drained again! I just want to make sure that it is the battery because I will replace it myself, do not have enough money to take it for repair.

  It does not appear as if the battery can be wrong - you can take it into Apple - diagnosis is free - the price is for the repair - if at least you will know if your suspicions are correct or if there is another question

  Please take a genius appointment at an Apple Store, or select another authorized service provider.

  Also, as you know - if you open the phone - you cancel your rights to the service to Apple

• Graphics card on the Satellite A100-386 maybe replaced/implemented to date?

  Hi all

  Probably having heat with my satellite a100 problem, I ran to the point were the remains of dark screen and no boot at all!
  Everything has been cleaned inside the dust thermal paste applied on the three places needed.

  A few months ago, I put 2 RAM to 2 GB to she thrust a little: he was fine until a few days with moment stops after an hour or so at the end of the great: do not start with no beep, nothing except the fan and the power led.

  Open it, I saw the thing near the fan which could be the video card, which seems to be removable, quite rare is it not?

  If that's really remplaceable, I need to find the exact same, card nvidia geforce Go 7300 Tc, say on the card, or is there the possibility to put a better card?

  As far as I know, it does not reserve an establishing a removable part so can in any way with the other parts of the computer to change (compatibility), unless it is for reasons of cost...

  Thanks for help

  AFAIK GPU is not extensible and on some model GPU is not fixed on the motherboard and can be exchanged. If you want to replace it than just with the same if one only, you will be able to buy a.

  >.. no more boot with no beep, nothing except the fan and the power led.
  That is a little strange that there is no sound signal. To me, it sounds like a BIOS problem.

• EliteBook 8530w becomes extremely hot!

  I have an Elitebook 8530w for a few years now and for a few weeks, it's extremely hot, without the laptop even do anything just to be inactive in windows.

  I can bear high enough levels of heat with my hands, but the temperature of the air coming out of the exhaust on the left is so hot that I can't hold my hand in front of her. Today I need to download a software for my new office, so I used one of the USB slots on the left (near the exhaust), as the other 2 were occupied. After like 20 minutes, I removed my USB flash drive and almost immediately, drop it on my table, because the drive was too hot to handle.
  
  This is not normal, that last week I lift the rear of the cell upward in the air a bit for the fan sucks air much more easily, but it doesn't seem to work at all.
  Is this normal or is something wrong?

  Welcome to liquid.

  IM installing a new OS on a 8530w.

  After you have everything installed Vista I could barely touch the laptop.

  It was so hot.

  But on mine, there was little or no air flow coming out to the left upper exhaust.

  So I removed the keyboard. "" Two screws on the bottom and the four pieces of restraint between esc - f1, f4 - f5 and f8 - f9-f12-scrolling.

  In the upper left corner, remove the connector of the fan.

  Remove the 3 couple for the fan.

  Remove the fan and clean between the fan and the radiator fins.

  Replace in reverse.

  Let me know if you need more information.

• Satellite click Mini L9W - B - overheated

  It's over heated anyone know what I can do to fix this or if it sets itself once cooled it won't continue for two days and it turns on just them black screen even once, I sat next to heater and he just had to I didn't know what could happen because I always sat next to heater with my other laptop and It's never happened before

  Could be a damaged tablet. Try to press and hold the power button for 30 seconds, then try to turn on again or / and reinstall windows