Help please - configuration VPN AnyConnect crossed

Similar Questions

• Need help to configure VPN NAT traffic to ip address external pool ASA

  Hello

  I need to configure vpn NAT ip address traffic external pool ASA

  For example.

  Apart from the ip address is 1.1.1.10

  VPN traffic must be nat to 1.1.1.11

  If I try to configure policy nat or static nat ASA gives me error "global address of overlap with mask.

  Please, help me to solve this problem.

  Thank you best regards &,.

  Ramanantsoa

  Thank you, and since you are just 1 IP 1.1.1.11 Polo, the traffic can only be initiated from your site to the remote end.

  Here is the configuration of NAT:

  access list nat - vpn ip 192.168.1.0 allow 255.255.255.0 10.0.0.0 255.255.0.0

  NAT (inside) 5 access list nat - vpn

  Overall 5 1.1.1.11 (outside)

  In addition, the ACL crypto for the tunnel from site to site should be as follows:

  access-list allow 1.1.1.11 ip host 10.0.0.0 255.255.0.0

  Hope that helps.

• Help! Configuration VPN Pix535 does not

  Hello

  We are trying to implement a remote vpn to allow clients to our private lan and then be able to use outgoing https. Don't break the tunnel, according to the needs of the client to look like they come from our area. Any help would be greatly appreciated. We can connect to the vpn with the customer, and we can ping within the network, but have problems trying to use HTTPS coming out through the client. Please find my current config attached. Thanks in advance.

  permit same-security-traffic intra-interface

  NAT (outside) 101 172.21.200.0 netmask 255.255.255.240

  I would also add...

  ISAKMP nat-traversal crypto

• IPsec VPN site to site between router problem Cisco ASA. Help, please

  Hello community,

  I'm stuck in configuring VPN site to site between ASA (OS 9.1) and router Cisco IOS (IOS 15, 2 - 4.M4)

  Attachment is router configuration and ASA. I also include the router debug output.

  It seems that the two parties must isakmp missmatch configuration, but I have already disabled the KeepAlive parameters. I also turn off PFS setting on both sides. But it does not work. I have no idea on this problem.

  Please help me. Any help appreciated.

  Thank you

   
   

  I didn't look any further, but this may be a reason:

   crypto map mymap 1 ipsec-isakmp dynamic dyn1 

  The dynamic CM must always be the last sequence in a card encryption:

   no crypto map mymap 1 ipsec-isakmp dynamic dyn1 crypto map mymap 65000 ipsec-isakmp dynamic dyn1

  Try this first, then we can look further.

• Help, please! Connected to the VPN, but cannot access internal servers.

  Hi friends,

  I'm a newbie on vpn stuff, I set up a base on a Cisco ASA 5505 vpn by using ASDM, and I was able to connect to it.  However, I can't ssh or RDP to one of the servers in the House after that I connected to the vpn.  Here is the configuration.  Help, please!

  ASA Version 8.2 (5)

  !

  hostname sc - asa

  domain abc.com

  enable the encrypted password xxxxxxxxx

  xxxxxxxxx encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain OpenDNS.com

  sc-pool_splitTunnelAcl-list of allowed access standard 192.168.1.0 255.255.255.0

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.96 255.255.255.240

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool sc-192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  interface ID client DHCP-client to the outside

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd dns 208.67.222.222 208.67.220.220 interface inside

  rental contract interface 86400 dhcpd inside

  dhcpd abc.com domain inside interface

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  SSL encryption rc4 - md5, rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1

  WebVPN

  abc group policy - sc internal

  attributes of the strategy of group abc - sc

  value of server DNS 208.67.222.222 192.168.1.3

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value abc-sc_splitTunnelAcl

  field default value abc.com

  a001 xxxxxxxxxxx encrypted password username

  a002 xxxxxxxxxxx encrypted password username

  username a003 encrypted password privilege 0 xxxxxxxxxxx

  a003 username attributes

  Strategy Group-VPN-abc-sc

  a004 xxxxxxxxxxx encrypted password privilege 0 username

  a004 username attributes

  Strategy Group-VPN-abc-sc

  a005 xxxxxxxxxxx encrypted password username

  a006 xxxxxxxxxxx encrypted password username

  username privilege 15 encrypted password xxxxxxxxxxx a007

  remote access to tunnel-group abc - sc type

  attributes global-tunnel-group-abc - sc

  address sc-pool pool

  Group Policy - by default-abc-sc

  tunnel-group abc - sc ipsec-attributes

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:e7df4fa4b60a252d806ca5222d48883b

  : end

  Hello

  I would suggest you start by changing the pool VPN to something else than the current LAN network and see if that helps

  These should be the configuration required to achieve this goal

  • First remove us pool setup VPN VPN
  • Then we delete the VPN Pool and create again with an another address space
  • When then attach this new Pool of VPN again to the VPN configuration
  • In the last step, we add a NAT0 / exempt for this new pool VPN NAT configuration and remove the old ACL line for the former group of VPN

  attributes global-tunnel-group-abc - sc

  no address-sc-swimming pool

  no ip local pool sc 192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  IP local pool sc-192.168.100.100 - 192.168.100.110 mask 255.255.255.0

  attributes global-tunnel-group-abc - sc

  address sc-pool pool

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.100.0 255.255.255.0

  No inside_nat0_outbound access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.96 255.255.255.240

  -Jouni

• Help, please! Cannot access the web after connected to the VPN

  Hello

  I'm a newbie on Cisco products.  I configured a Cisco ASA 5505 with VPN firewall.  However, I can't access the web after I connected to the remote IPSec VPN.  I also cannot connect to the bands using the intellectual property.  But I can connect to the internal servers in the office with no problems.

  Here is my setup, can someone help please?  Thank you very much

  ASA Version 8.2 (5)

  !

  host name asa

  xxxxxxxxx.com domain name

  enable the encrypted password xxxxxxxxxxx

  xxxxxxxxxxx encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  passive FTP mode

  area of zone clock - 8 schedule

  clock summer-time recurring PDT 1 Sun Apr 02:00 last Sun Oct 02:00

  DNS lookup field inside

  DNS server-group DefaultDNS

  Server name 107.204.233.222

  name-server 192.168.1.3

  xxxxxxxxx.com domain name

  inside_nat0_outbound list of allowed ip extended access all 192.168.1.96 255.255.255.240

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool sc-192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 192.168.1.0 255.255.255.0

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint _SmartCallHome_ServerCA

  Configure CRL

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.0 inside

  SSH timeout 5

  Console timeout 0

  interface ID client DHCP-client to the outside

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd dns 107.204.233.222 inside the 192.168.1.3 interface

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal strategy group xxxxxxxx-sc

  attributes of xxxxxxxx-sc group policy

  value of 107.204.233.222 DNS server 192.168.1.3

  Protocol-tunnel-VPN IPSec

  XXXXXXXXXX.com value by default-field

  xxxxx xxxxxxxxxxx encrypted password username

  Strategy Group-VPN-xxxxxxxx-sc

  remote access to tunnel-group xxxxxxxx-sc type

  attributes global-tunnel-group xxxxxxxx-sc

  address sc-pool pool

  Group Policy - by default-xxxxxxxx-sc

  tunnel-group xxxxxxxx-sc ipsec-attributes

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  call-home service

  anonymous reporting remote call

  call-home

  contact-email-addr [email protected] / * /

  Profile of CiscoTAC-1

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:5c1c99b09fb26fcc36a8bf7206af8e02

  : end

  Hello

  Try adding the following commands

  permit same-security-traffic intra-interface

  NAT (outside) 1 192.168.1.96 255.255.255.240

  Is there are always problems with VPN then I would maybe change VPN pool to anything other than something that comes into conflict with the LAN.

  In this case, these configurations should do the trick

  In order from top to bottom, they would do the following things

  • First remove the pool VPN and VPN configurations
  • Then remove the VPN pool
  • Remake of the VPN Pool with different network
  • Reattach the VPN pool for VPN configurations
  • Configure NAT0 to the new cluster of VPN
  • Remove the old line of the ACL of the configuration of NAT0

  attributes global-tunnel-group xxxxxxxx-sc

  no address-sc-swimming pool

  no ip local pool sc 192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  IP local pool sc-192.168.2.10 - 192.168.2.254 mask 255.255.255.0

  attributes global-tunnel-group xxxxxxxx-sc

  address sc-pool pool

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0

  no access list inside_nat0_outbound extended permits all ip 192.168.1.96 255.255.255.240

  Of course you also have the NAT configuration for VPN pools new Internet traffic

  NAT (outside) 1 192.168.2.0 255.255.255.0

  Please rate if the information has been useful if this resolved the issue as mark responded.

  -Jouni

• Failed to configure two AnyConnect & IPSEC site to site VPN

  I have established a VPN IPSEC site-to-site

  When I configure the AnyConnect (make it work) and I lose the tunnel from site to site and vice versa.

  I think that my NAT syatements are incorrect.

  Here is the config NAT when AnyConnect works properly...

  Overall (101 outside interface)
  NAT (inside) 0-list of access sslnonat
  NAT (inside) 101 0.0.0.0 0.0.0.0

  access extensive list ip 192.168.65.0 sslnonat allow 255.255.255.0 192.168.66.0 255.255.255.0

  When the IPSEC tunnel site-to-site work properly, here's the NAT config...

  Overall (101 outside interface)
  NAT (inside) 0-list of access Inside_nat0_outbound
  NAT (inside) 101 0.0.0.0 0.0.0.0

  Access extensive list ip 192.168.65.0 Inside_nat0_outbound allow 255.255.255.0 ServerGroup object-group

  How do I get to the AnyConnect and the IPSEC Site to site both to work properly? I need not reach on the other.

  Network within 192.168.65.0/24

  AnyCOnnect address pool 192.168.66.0/24

  Any help would be appreciated.

  Hello

  Try this:

  Overall (101 outside interface)
  NAT (inside) 0-list of access Inside_nat0_outbound
  NAT (inside) 101 0.0.0.0 0.0.0.0

  Access extensive list ip 192.168.65.0 Inside_nat0_outbound allow 255.255.255.0 ServerGroup object-group
  Access extensive list ip 192.168.65.0 Inside_nat0_outbound allow 255.255.255.0 192.168.66.0 255.255.255.0

  The problem is that when you apply the IPsec NAT configuration, you remove the entry for the AnyConnect pool.
  Try the above and we will see if it works.

  Federico.

• Hi, I just got a second generation ipod nano, and whenever I have unplug the charger a line crosses the screen. Help, please

  Hi, I just bought a used second generation ipod nano and whenever I have unplug the charger a line crosses the screen and I can't do anything with the ipod. Help, please.

  When you do a Reset (reboot) on the iPod

  Learn how to reset your iPod - Apple Support  (see iPod with a click wheel)

  do you see this line on the screen when the Apple logo?  If you do, it is probably a hardware problem.  If the line is not there at the start, but returns after the iPod starts, you can do a restore of the iPod using iTunes.  This d erases the IPO, reinstall its software and sets it to the default settings.

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod settings - Apple Support

  If the problem persists after the restore, the cause is likely to be hardware problem.

• Please give index on configuring vpn site to site on 881 to ASA 5505 cisco router

  Earlier my boss asked me to prepare to implement the VPN site-to site on router Cisco 881 Integrated Services to ASA 5505 router, which is now running on the side of HQ. Someone please give me a hint. I am now learning the pdf file from Cisco that mention how to configure VPN site to site between 1812 Cisco IOS router and router of the ASA 5505 using ASDM V6.1 and SDM V2.5. Cannot find the book for the Cisco 881 device.

  Someone please please suggest me something as soon as POSSIBLE.

  Thank you

  CLI version:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml

  ASDM and SDM Version:

  http://www.Cisco.com/en/us/partner/products/ps5855/products_configuration_example09186a0080a9a7a3.shtml

• need to connect and configure the oracle on windows 7 vmware professional database? Help, please?

  Hello

  In fact, I wanted to set up ORACLE with Informatica Power Center (ETL) database connection. But my problem is that I installed the oracle database with grid inside VMWARE with the RHEL operating system. But what INFORMATICA etl software is installed outside VMWARE, which is located in WINDOWS 7 Professional.

  I would like to know how I can access and configure oracle database of windows 7 Professional as oracle database is installed inside VMWARE RHEL 6.5 operating system.

  Help, please.

  HERE'S HOW I SOLVED IT: -.

  
  Here is the url for the NAT that could become useful for other institutions.

  How to Setup Port Forwarding in VMware Workstation 9 | Virten.NET

• How can I configure reader adobe XI as one of my printer port? Help, please.

  How can I configure reader adobe XI as one of my printer port? Help, please.

  Adobe Acrobat (Windows only) comes with a virtual printer that allows you to create PDF files. The free player does not work.

• I've just upgraded to PSE 12 and first E 12 and tried to installed several times.  Pop up says "Configuration Error"; contact Adobe Tech Support (?); and "mention the error code 1"!  Help please!

  I've just upgraded to PSE 12 and first E 12 and tried to installed several times.  Pop up says "Configuration Error"; contact Adobe Tech Support (?); and "mention the error code 1"!  Help please!

  Installation seems to work fine until, and including 'Technologies share '...

  I have cleaned all the disk *.tmp files, deleted all the shortcuts and various Adobe programs and he then successfully installed.

  Now, if I can get the updates to work.  There is always a challenge with the Adobe software.

• BlackBerry Z10 Z10 will not accomplish configuration after the update of device software, help please.

  Help please, cannot complete phone ater installation performing a software update by using the link to Blackberry.

  Sequence of events;

  Recognized by link to Blackberry phone.

  Reload the selected device - available 10.0.10.90 updated version software.

  Get - software update seems to load correctly then unplugged Z10.

  Phone restarts, welcome to Blackberry, English (UK) checked, swupe left.

  No available SIM card, slide to WI - Fi.

  Password entered for home network and confirmation screen displays connected.

  Agree screen - countries changed to United Kingdom (English),

  the bottom slot, I agree to the Blackberry ALS...
  "I agree" and "I do not accept" buttons cannot be selected and
  After a short delay could not connect appears.

  By pressing "Settings" goes back to the page of the networks Wi - Fi with
  confirmation that the connection is good and round, there it is again.

  Completing the update software several times as indicated above and also of

  www.BlackBerry.com/updates by forum next display to

  http://supportforums.blackberry.com/t5/General-BlackBerry-10-Smartphone/How-

  to-Reload-your-Blackberry10-OS/td-p/2187545

  and get the same result every time I would appreciate help to solve this problem.

  Result, I thank you, using a WiFi hotspot from another phone installation completed perfectly. Now curiously etc.on Z10 browser works perfectly uning home WiFi. Again, thank you for your advice. Best regards, Bob

• I am trying to configure Adobe Premier Pro 2.0, and he asked me for a serial number. I looked at my history of orders and my products, but according to them, I made no order or a purchase. Help please!

  Help please!

  CS2, Acrobat 7 + Audition 3 (AND PREVIOUS) activation server has disappeared, then read below

  You MUST use the special version and the serial number on the page, not your original drive or serial number

  l http://helpx.adobe.com/x-productkb/Policy-Pricing/Creative-Suite-2-activation-end-Life.htm

  NOTE that CS2 will not install on a Mac "modern" with an Intel processor, and when you install the special version of the PPro2 on a Win7 computer Win8 or Win10, you may need to right click on the program icon and select Windows XP compatibility in the popup of option

• Cisco ASA 5510 - restrictions of VPN (AnyConnect) based on the AD user or IP address

  Hello

  I want to test how to restrict access user on an ASA 5510 AnyConnect. In politics, I can define what networks will go through the VPN tunnel and which not (split tunneling). The ASA has a LDAP connection and only AD users with a special security group can connect over AnyConnect.
  On the other hand I would like to restrict access for special users within a VPN policy.

  So my question:
  What are your recommendations to implement this szenario?

  My two ideas would be:
  1. the access rules based on the user of the AD.
  2. special reserve IP addresses in the pool of addresses AnyConnect for some users, so I can limit access to the normal firewall rules base based on the source IP address.

  What are your recommendations and is it possible to realize my ideas (and how)?

  Thanks in advance

  Best regards

  Hello

  I will suggest that you configure a second ad group in the server and another group strategy in the ASA, you can configure certain access on each group policy "the installer of the filters, assign different split political tunnel, different ACL' and in the ad server, you can assign users for example to the AD Group A and AD Group B based on the access you want to give them now , you must configure LDAP mapping to assign the user specific group policy that you want based on the AD group that they belong.

  You can follow this documentation that will help you configure the LDAP Mapping:

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  Best regards, please rate.