Need help to configure VPN NAT traffic to ip address external pool ASA

Similar Questions

• Help please - configuration VPN AnyConnect crossed

  Hi there, forgive me if I missed all the protocols forum because this is my first post.

  I am trying to configure an AnyConnect VPN and I think it's nearly there, but not enough yet. When I connect from an outside network, it gives me the following error '... No address is available for an SVC connection. I checked the pools of addresses and what I see, they are assigned to the profile. I'm doing it also crossed, I all VPN traffic through this router... traffic LAN and remote Internet sometimes when I'm on the unfamiliar wifi hotspots. I tried to get this to work for more than 1 week with a lot of different forums to scouring. I have included my config running for anyone to help me with. I appreciate a lot of the answers to get me on the right track. Thank you.

  Update 15 minutes later: I posted my SSLVPN IP pool to the DefaultWebVPNGroup and it connected but I was unable to browse the web or ping network resources. I would like to disable the "DefaultWebVPNGroup" without any consequences for the installation program. What I still have to disable?

  -------------------------------------------------------------------------------

  Output from the command: 'show running-config '.

  : Saved

  :

  ASA Version 8.4 (2)

  !

  ciscoasa hostname

  activate 8Ry2YjIyt7RRXU24 encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  192.168.123.1 IP address 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  boot system Disk0: / asa842 - k8.bin

  passive FTP mode

  DNS lookup field inside

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  Server name 208.67.220.220

  name-server 208.67.222.222

  permit same-security-traffic intra-interface

  network obj_any object

  subnet 0.0.0.0 0.0.0.0

  object-group service DM_INLINE_SERVICE_1

  the purpose of the ip service

  the purpose of the tcp destination eq https service

  the purpose of the tcp destination eq pptp service

  the purpose of the service tcp destination eq www

  object-group service DM_INLINE_SERVICE_2

  the purpose of the ip service

  the purpose of the tcp destination eq https service

  the purpose of the tcp destination eq pptp service

  outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_1 all 192.168.123.0 255.255.255.0

  inside_access_in list extended access allow the object-group 192.168.123.0 DM_INLINE_SERVICE_2 255.255.255.0 any

  allow a standard ACL1 access list

  ACL1 list standard access allowed 192.168.123.0 255.255.255.0

  access-list nat0 extended 192.168.123.0 allowed any ip 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  mask 192.168.132.50 - 192.168.132.60 255.255.255.0 IP local pool SSLVPNpool

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 645.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (exterior, Interior) source Dynamics one interface

  NAT (inside, outside) source Dynamics one interface

  inside_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 76.x.x.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  http 192.168.123.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  interface ID client DHCP-client to the outside

  dhcpd dns 208.67.220.220 208.67.222.222

  dhcpd outside auto_config

  !

  dhcpd address 192.168.123.150 - 192.168.123.181 inside

  dhcpd allow inside

  !

  a basic threat threat detection

  host of statistical threat detection

  statistical threat detection port

  Statistical threat detection Protocol

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow inside

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.3054-k9.pkg 1

  AnyConnect image disk0:/anyconnect-macosx-i386-2.5.3054-k9.pkg 2

  AnyConnect enable

  internal group SSLVPN strategy

  SSLVPN group policy attributes

  client ssl-VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  by default no

  the address value SSLVPNpool pools

  WebVPN

  AnyConnect Dungeon-Installer installed

  time to generate a new key 30 AnyConnect ssl

  AnyConnect ssl generate a new method ssl key

  AnyConnect ask flawless anyconnect

  attributes of Group Policy DfltGrpPolicy

  value of server DNS 208.67.220.220 208.67.222.222

  client ssl-VPN-tunnel-Protocol

  username Vxxxxx ZyAw6vc2r45CIuoa encrypted password

  username Vxxxxx attributes

  VPN-group-policy SSLVPN

  client ssl-VPN-tunnel-Protocol

  admin password 61Ltj5qI0f4Xy3Xwe26sgA user name is nt encrypted privilege 15

  username Sxxxxx qvauk1QVzYCihs3c encrypted password privilege 15

  Sxxxxx attributes username

  VPN-group-policy SSLVPN

  client ssl-VPN-tunnel-Protocol

  tunnel-group SSLVPN type remote access

  tunnel-group SSLVPN General attributes

  address (inside) SSLVPNpool pool

  address pool SSLVPNpool

  Group Policy - by default-SSLVPN

  tunnel-group SSLVPN webvpn-attributes

  allow group-alias SSLVPN_users

  !

  !

  !

  World-Policy policy-map

  class class by default

  Statistical accounting of user

  !

  service-policy-international policy global

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:989735d558c9b1f3a3a8d7cca928c046

  : end

  ----------------------------------------------------------------------------------------------------

  Thanks again to all.

  To access the internal resources of VPN, here's what needs to be configured for NAT:

  obj-SSL-pool of network objects

  192.168.132.0 subnet 255.255.255.0

  object obj-Interior-LAN network

  192.168.123.0 subnet 255.255.255.0

  Static NAT obj-Interior-LAN obj-Interior-LAN destination source (indoor, outdoor) obj-SSL-pool static obj-SSL-pool

  I also advise you to remove the following statement of the NAT:

  NAT (exterior, Interior) source Dynamics one interface

  If you want all traffic internet VPN to be routed to the tunnel, then here's the NAT config:

  object obj-SSL-internet network

  192.168.132.0 subnet 255.255.255.0

  dynamic NAT interface (outdoors, outdoor)

  And finally, you cannot disable the group policy by default 'DefaultWebVPNGroup '. So that when you log-in, you chose

  SSLVPN_users group of tunnel, which will apply SSLVPN automatically group policy that you have configured explicitly that.

  I hope this helps.

• Need help with configuration on cisco vpn client settings 1941

  Hey all,.

  I just bought a new router 1941 SRI and need help with the configuration of the parameters of the VPN client. Orders aspect a little different here, as I'm used to the configuration of ASA and PIX for vpn, routers not...

  If anyone can help with orders?

  I need the installation:

  user names, authentication group etc.

  Thank you!

  Take a peek inside has the below examples of config - everything you need: -.

  http://www.Cisco.com/en/us/products/ps5854/prod_configuration_examples_list.html

  HTH >

  Andrew.

• Need help with Config VPN on ASA5505

  Our client has a seller who needs to establish a VPN tunnel to their own router that sits behind our firewall.

  Concentrator VPN (seller) ASA5505 customer (7.2) <------> <------->3750 Switch <------->VPN router (Vendor)

  Here is the implementation of information:

  ASA outside Interface - 208.64.1x.x4 DG - 208.64.1x.x3

  ASA inside the Interface - 172.20.58.13/30

  3750 switch Interface connected to ASA - DG - 172.20.58.13 and 172.20.58.14/30

  3750 switch Interface connected to router VPN - 172.20.58.21

  The Interface of the VPN router connected to the 3750 - 172.20.58.22/30 DG - 172.20.58.21

  I have also attached a Visio for that and the current configuration of execution of ASA and 3750. We have no access to the router VPN TNS.

  Our responsibility is to everything just to make sure that the tunnel rises.

  You kindly help me with this?

  Here is what I intend to do:

  (1) create a static NAT on the ASA Public Private IP Address of the VPN router

  Public - 208.64.1x.x5 / 28

  Private - 172.20.58.21 / 30

  Will be the ASA automatically ARP for this address or do we I have to configure another interface on the ASA with this public IP address?

  (2) what would the access on the ASA list?

  (3) the customer gave us some config to copy the stuff on the SAA so that they can create the tunnel but I couldn't put these commands in the SAA. How this would apply and which interface?

  Access to firewall: the information below is about access between the VPN router and the

  VPN concentrator. If a firewall/router is present in front of the VPN services must be

  permit:

  allow a host 208.224.x.x esp

  allow a host 208.224.x.x gre

  permit any isakmp udp host 208.224.x.x eq

  permit any eq non500-isakmp udp host 208.224.x.x

  allow a host 204.8.x.x esp

  allow a host 204.8.x.x gre

  permit any isakmp udp host 204.8.x.x eq

  permit any eq non500-isakmp udp host 204.8.x.x

  permit tcp 206.x.x.0 0.0.0.255 any eq 22

  permit tcp 206.x.x.0 0.0.0.255 any eq telnet

  allow a udp host 208.224.x.x

  allow a udp host 208.224.x.x

  Can someone help me with the commands I need to run it on the ASA? The 5505 running 7.2 code (4).

  Thanks in advance.

  HS

  Your steps are correct, you need to configure static NAT and the list of access to allow access.

  Static NAT would be as follows:

  static (inside, outside) 208.64.1x.x5 172.20.58.21 netmask 255.255.255.255

  You also need a road inside interface-oriented join 172.20.58.21:

  Route inside 172.20.58.21 255.255.255.255 172.20.58.14

  You have already access list on the external interface? If you have, then just add in the existing access list, if you don't have it, and then add the following:

  access list outside-acl permit udp any host 208.64.1x.x5 eq 500

  access list outside-acl permit udp any host 208.64.1x.x5 eq 4500

  access list outside-acl allow esp any host 208.64.1x.x5

  Access-group acl outside in external interface

  If you also have an inside interface access list, you must also allow passing traffic by as follows:

  access-list allow host 172.20.58.21 udp any eq 500

  access-list allow host 172.20.58.21 udp any eq 4500

  access-list allow host esp 172.20.58.21 all

  If you have not had any access inside the interface list, then you don't need to configure it.

  Hope that helps.

• Configuration VPN - NAT - T support

  Hello

  A partner of business (BP) has the following requirements. I don't know which statements of config I need to use to ensure this successful connection

  Business (BP) needs partner complete the VPN tunnel on a firewall that is behind another firewall running NAT

  (BP) will create UDP 500 and UDP 4500 endpoints on the NAT firewall which is forwarded to the Firewall VPN termination.

  Because of this, the (BP) needs of my dissertation support encapsulation of ESP over UDP (NAT - T)

  My series of ASA5500 using the code (825) has the statements

  Crypto isakmp nat-traversal 21
  crypto ISAKMP ipsec-over-tcp port 10000

  VPN # match address BP_VPN crypto card
  VPN # set peer (peer_ip) crypto card
  VPN # game of transformation-AES_256_SHA crypto card

  IPSec-l2l type tunnel-group (peer_ip)
  IPSec-attributes of tunnel-group (peer_ip)
  pre-shared key (TBD)

  BP_VPN list extended access permit tcp host 10.x.x.x, 172.16.x.x eq (specified port) host
  BP_VPN list extended access permit tcp host 10.x.x.y host 172.16.x.x eq (specified port)

  NatExempt_VPN list extended access permit tcp host 10.x.x.x, 172.16.x.x eq (specified port) host
  NatExempt_VPN list extended access permit tcp host 10.x.x.y host 172.16.x.x eq (specified port)

  Please indicate whether these statements are sufficient and if not what else would be needed.

  You need not order

  crypto isakmp ipsec-over-tcp port 10000

  It is for the exclusive implementation that was used before NAT - T is available. You only need to nat-traversal active. For your ACL, using ports in there makes everything complicated. You should see if you can just use 'ip' here. If there is already configured on your ASA virtual private networks, then the config is probably ok. If this isn't the case, you must always configure ISAKMP and activate the encryption on the interface card.

• HP C4580 not scan to PC. I need help to configure my Netgear router please :)

  Hello

  I've read here, the threads that talk about this printer prints only not to or from a PC - my problem is that the C4580 go scan from my PC, but will not scan to PC.

  I found an answer from someone who has had the same problem earlier this year, but I do not understand what to do.

  Here's the answer:

  "I have ordered mine entering the settings from my router (Netgear) page and setting the built-in firewall rules. "The internal firewall was blocking the printer, I could print, scan using the computer, just could not scan from the printer to the computer.

  Also, I have a Netgear router, but could do with help on how to do the same thing as the person above.

  Thanks in advance for any help!

  Sorry, I don't need help after all

  It was not the router requires a configuration, it is the firewall that was a block that should be changed to "allow".

  My "all-in-one" now does everything it is supposed to do

• I need help for configuring security for my wireless again.

  Need a help for my Wi - Fi Protected Access set up again... somehow I deleted it while trying to access the networks wireless outside my house.

  original title: Wi - Fi Protected Access

  Hi dmcangus,

  See the Microsoft articles below for more information on WPA wireless security.

  Configure Security Wireless WPA for home networks

  http://Windows.Microsoft.com/en-us/Windows-XP/help/networking/configure-WPA-wireless-security

  Overview of upgrading security Wi - Fi Protected Access (WPA) in Windows XP

  http://support.Microsoft.com/kb/815485

• Debugging - need help with configuration

  I also posted this in advanced by accident...

  I need help to my local development for CFBuilder debugging machine configuration. Developing CF applications is configured correctly, but I have problems configuring settings for debugging for CFBuilder/Eclipse. CFBuilder is installed and connected to RDS, and CF administrator is configured to debug level line. I'm running Windows 7 x 64 with ColdFusion 9 (using IIS).

  All my projects are in my "C:\Dev" folder, and each project contains a folder "www", which is the root of the web project. So, I have my projects organized like this:

  C:\Dev

  TestSite

  design

  docs

  www <-web root folder

  , I have created a ColdFusion project and he mapped directly to the folder root 'www '. In IIS, the web root folder is mapped via a virtual directory under the web site default and is accessible from "http://127.0.0.1/testsite"" "

  I have configured my RDS server that works correctly, so I can see the databases on the server. Nice. I also set up a server in the list of servers in the perspective of coldfusion and imported directly from my RDS server settings. It has the same name as my RDS Server, which is 'Server RDS Local.' I also added a URL prefix for "testsite" which is mapped to the local path: (C:\Dev\TestSite\www) and "http://127.0.0.1 \testsite. And finally, in Debug maps (preferences window), I said 'Server RDS Local.'

  Everything seems to be installed, but I can not debug. Here's what happens:

  Of the ColdFusion perspective, I click with the right button on index.cfm and select "Debug-> ColdFusion Application" the first time I do it, it switches on the ColdFusion debugging Perspective and loads of " " http://Homepage/ 'and then nothing seems to work. On the debugging tab, it shows me that he has created a new launch for my project as follows:

  TestSite

  Local RDS Server

  Model of ColdFusion

  I see my breakpoint in my breakpoints tab. But I can't seem to get any further. I can't find a way to run at my breakpoint. The home page for the current debugging session is "http://homepage/" which is something I don't understand. How CFBuilder go to the correct home page for the debug session? Maybe that's the key of.

  Hello

  Please right click on the project, and you will see an option "set the URL prefix. Allows to set the URL of your project.

  Thank you!

  Bhakti

• Need help on ASA5505 VPN configuration

  Hello

  For the life of me I can't get this to work. I know it is something simple, yet I've not thought about it.

  My father-n-law lives in China and they block a lot of sites in the United States. I have my set VPN in place in the United States for remote access, but to get there from China it still cannot connect to the United States sites. Can someone help me if I can get this working properly?

  Thanks in advance!

  EricO

  Great, thank you.

  Here's what you need to add:

  permit same-security-traffic intra-interface

  China-VPN network object

  255.255.255.0 subnet 192.168.100.0

  dynamic NAT interface (outdoors, outdoor)

  group attributes political kikou

  Split-tunnel-policy tunnelall

  no value in split-tunnel-network-list KaileY_splitTunnelAcl

• Need help for IPSEC VPN configuration.

  Hello

  I'm trying to implement a VPN IPSEC connection in my GNS3 lab and all show commands and debugs does not seem to give me clues of what is wrong or missing... can someone please help me in my troubleshooting VPN config. Here is the config for Router 1

  R1 #sh run

  crypto ISAKMP policy 1

  preshared authentication

  Group 2

  ISAKMP crypto key 6 cisco123 address 200.20.1.1

  !

  !

  Crypto ipsec transform-set esp - esp-sha-hmac CISCO_SET

  !

  map VPN_map 10 ipsec-isakmp crypto

  ! Incomplete

  defined by peer 200.20.1.1

  Set security-association second life 190

  game of transformation-CISCO_SET

  match address INT_TRAFFIC

  !

  !

  interface Loopback1

  IP 172.16.1.1 255.255.255.255

  !

  interface Loopback2

  172.16.1.2 IP address 255.255.255.255

  !

  interface FastEthernet0/0

  IP 200.11.1.1 255.255.255.252

  IP ospf 1 zone 0

  automatic duplex

  automatic speed

  card crypto VPN_map

  !

  router ospf 1

  Log-adjacency-changes

  network 172.16.0.0 0.0.255.255 area 0

  !

  router bgp 65001

  no synchronization

  The log-neighbor BGP-changes

  200.11.1.0 netmask 255.255.255.252

  neighbour 200.11.1.2 distance - as 65030

  No Auto-resume

  !

  IP forward-Protocol ND

  !

  !

  IP http server

  no ip http secure server

  !

  INT_TRAFFFIC extended IP access list

  IP address 172.16.0.0 allow 0.0.255.255 192.168.0.0 0.0.255.255

  IP address 172.16.0.0 allow 0.0.255.255 192.168.0.0 0.0.255.255 connect

  end

  R1 #sh crypto isakmp his

  IPv4 Crypto ISAKMP Security Association

  status of DST CBC State conn-id slot

  IPv6 Crypto ISAKMP Security Association

  R1 ipsec crypto #show her

  Nill...

  R1 #sh debugging

  Encryption subsystem:

  Crypto ISAKMP debug is on

  Engine debug crypto is on

  Crypto IPSEC debugging is on

  Regulation:

  memory tracking is enabled

  R1 #sh ip route

  Gateway of last resort is not set

  200.20.1.0/30 is divided into subnets, subnets 1

  B 200.20.1.0 [20/0] via 200.11.1.2, 01:28:21

  200.11.1.0/30 is divided into subnets, subnets 1

  C 200.11.1.0 is directly connected, FastEthernet0/0

  172.16.0.0/32 is divided into subnets, 2 subnets

  C 172.16.1.1 is directly connected, Loopback1

  C 172.16.1.2 is directly connected, Loopback2

  R1 #ping 200.20.1.1

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 200.20.1.1, wait time is 2 seconds:

  !!!!!

  See you soon,.

  Fabio

  Nice Catch. The key word 'Incomplete!' should have reported it.

  Please close the issue as resolved - user error

  Thank you
  Brian

• Need help with native VPN client for Mac to the Configuration of the VPN router RV082

  Guys,

  I am trying to set up router RV082 VPN Client with native Mac for my remote access. However, no matter what I did, I'm not able to make works. Can any give me an example of how to set my router RV082 and Mac Book Pro (Mountain Lion)?

  Thank you

  Hi Jixian, the native client MAC does not work. The IPSEC VPN client is the same as the 5.x Cisco VPN client is not supported on this device.

  Your alternatives are to use PPTP or a 3rd party IPsec client such as ipsecuritas.

  -Tom
  Please evaluate the useful messages

• Help! Configuration VPN Pix535 does not

  Hello

  We are trying to implement a remote vpn to allow clients to our private lan and then be able to use outgoing https. Don't break the tunnel, according to the needs of the client to look like they come from our area. Any help would be greatly appreciated. We can connect to the vpn with the customer, and we can ping within the network, but have problems trying to use HTTPS coming out through the client. Please find my current config attached. Thanks in advance.

  permit same-security-traffic intra-interface

  NAT (outside) 101 172.21.200.0 netmask 255.255.255.240

  I would also add...

  ISAKMP nat-traversal crypto

• Need help with ikev1 VPN site-to-site

  Hi guys,.

  I have 2 asa 5505, the two 8.4 (4) running with ASDM 6.4 (9).

  I rebuild the config probalby 6 times now, with no clue what I am doing wrong.

  My main gig is, why the asa are not same initiator VPN negiotiation, no traffic at all.

  OK, I can ping both devices on their external interfaces.

  IKEv1 is enabled on the external interfaces.

  I checked the connection profile, group of tunnel, cryptographic cards, IKE strategies, etc.

  Always nothing less newspapers, which would indicate any attempt of negotiation.

  Help, please!

  Hello

  Well, that really depends on your configuration. For the most amount of networking to each site using the VPN L2L.

  But generally you can configure with

  object-group, LAN

  network-object

  object-group, REMOTE network

  network-object

  Destination LOCAL LOCAL Shared source (indoor, outdoor) NAT static REMOTE

  Naturally, the names of "object-group" can be different and your interfaces cannot be named 'inside' and 'outside'

  -Jouni

• vpn NATting traffic

  I have my vpn set up exactly as I need.  Users can connect to the vpn and get an IP of 172.16.17.0/24.  These users can access then machines hidden behind the asa on the private interface 172.16.16.1/24.  Users on the 172.16.16.1 interface can also access any machine not on the private through the router using nat interface.  What I can not understand how is allowing vpn also users to access any machine not on the private via NAT on the router interface. Help would be appreciated.

  See the road from ciscoasa #.
  Gateway of last resort is a.b.c.1 to network 0.0.0.0

  C 172.16.16.0 255.255.254.0 is directly connected, igbprivate
  S 172.16.17.20 255.255.255.255 [1/0] via a.b.c.189, igbpublic
  C 255.255.252.0 a.b.c.0 is directly connected, igbpublic
  C 192.168.1.0 255.255.255.0 is directly connected, management
  S * 0.0.0.0 0.0.0.0 [1/0] via ak.b.c.124.1, igbpublic

  access list

  access list 101 line 1 permit extended ip 172.16.16.0 255.255.255.0 172.16.17.0 255.255.255.0

  in the running-config nat statements

  interface of global (igbpublic) 1
  NAT (igbprivate) 0-access list 101
  NAT (igbprivate) 1 0.0.0.0 0.0.0.0

  If your VPN users connect on the side of the SAA Public then I still think Hairpining is what you should look into. It is very similar to my problem in which I want to VPN users to access internet through VPN. Packets from the VPN users must enter the public interface and return directly. I hope I understand this.

• Need HELP to change the NAT type to open on Linksys E2000.

  I was wondering if anyone could tell me how to change my nat from moderate to open so I can play xbox without any problems. But the strange thing is my nat was open, but it changed to moderate and I recently bought the linksys e2000 and it was open at first, but no more. If anyone can help me?

  Follow the below mentioned settings, then check.

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER...
  Let the empty user name & password use admin lowercase...
  On the Configuration tab change the size of the MTU to 1365, then click on save settings...
  Click the 'Administration' tab and disable the UPnP option and click on save settings...
  Click on the tab "Games and Applications" and then click the sub-tab "Port Range Forwarding"...
  (1) on the first line in the box, type Application in ABC, in the start box, type in 53 and type in 3074 service box, leave the Protocol as and under type 192.168.1.20 ip address and check the box to enable, click on save settings once it's been...
  (2) once you return to the game to the top page, click the Security tab and uncheck block anonymous Internet requests and click on save settings...
  (3) click on the status tab, and then note the DNS1 and DNS2 addresses...
  (4) address IP, Goto settings XBox network settings and assign the following on your Xbox and select manual IP settings
  IP address:-192.168.1.20, subnet mask:-255.255.255.0 default gateway:-192.168.1.1...
  (5) also assign addresses DNS on Xbox
  Use DNS1 and DNS2 addresses you took note of the primary router as secondary DNS & DNS status tab for the xbox...
  (6) turn off your modem, router and Xbox... Wait a minute...
  (7) plug the power to the modem first, wait a minute and plug the router power cable, wait another minute and turn on the Xbox and... test it connects...
  IP address: part 192.168.X. [last intellectual property in your device] for example if static ip given to the unit's 192.168.X.10 get the last part and put it in the empty box.