Help to activate SSL VPN router Cisco 1941

Similar Questions

• HOWTO configure SSL VPN router Cisco 1941?

  Hello.

  How to configure SSL VPN on a router Cisco 1941? I would like a howto guide that is step by step. I've found myself so far.

  Best regards Tommy Svensson

  Here are a few links that might help:

  http://www.Cisco.com/en/us/products/ps6657/prod_configuration_examples_list.html

  http://security-blog.netcraftsmen.NET/2009/02/Cisco-IOS-SSL-VPN-example.html

• Help to configure the router Cisco 1941

  Help!

  I just bought a router cisco 1941, I understand, it came with the Cisco CP, but I don't know how get you to the part where I can use it.

  Also, how can I connect to the router directly without using the HyperTerminal console, all I want to be able to do is configure the address IP of the ISP and my IP address so I can use it for surfing the internet.

  Help, please.

  Hello

  Thanks for the screenshots and show the output! You will need a few lines of command for CCP to work:

  Configure the terminal

  username username privilege 15 secret PASSWORD

  IP http server

  local IP authentication

  Sent by Cisco Support technique iPad App

• Router Cisco 1941 - crypto isakmp policy command missing - IPSEC VPN

  Hi all

  I was looking around and I can't find the command 'crypto isakmp policy' on this router Cisco 1941.  I wanted to just a regular Lan IPSEC to surprise and Lan installation tunnel, the command isn't here.  Have I not IOS bad? I thought that a picture of K9 would do the trick.

  Any suggestions are appreciated

  That's what I get:

  Router (config) #crypto?
  CA Certification Authority
  main activities key long-term
  public key PKI components

  SEE THE WORM

  Cisco IOS software, software C1900 (C1900-UNIVERSALK9-M), Version 15.0 (1) M2, VERSION of the SOFTWARE (fc2)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2010 by Cisco Systems, Inc.
  Updated Thursday, March 10, 10 22:27 by prod_rel_team

  ROM: System Bootstrap, Version 15.0 M6 (1r), RELEASE SOFTWARE (fc1)

  The availability of router is 52 minutes
  System returned to ROM by reload at 02:43:40 UTC Thursday, April 21, 2011
  System image file is "flash0:c1900 - universalk9-mz.» Spa. 150 - 1.M2.bin.
  Last reload type: normal charging
  Reload last reason: reload command

  This product contains cryptographic features...

  Cisco CISCO1941/K9 (revision 1.0) with 487424K / 36864K bytes of memory.
  Card processor ID FTX142281F4
  2 gigabit Ethernet interfaces
  2 interfaces Serial (sync/async)
  Configuration of DRAM is 64 bits wide with disabled parity.
  255K bytes of non-volatile configuration memory.
  254464K bytes of system CompactFlash ATA 0 (read/write)

  License info:

  License IDU:

  -------------------------------------------------
  Device SN # PID
  -------------------------------------------------
  * 0 FTX142281F4 CISCO1941/K9

  Technology for the Module package license information: "c1900".

  ----------------------------------------------------------------
  Technology-technology-package technology
  Course Type next reboot
  -----------------------------------------------------------------
  IPBase ipbasek9 ipbasek9 Permanent
  security, none none none
  given none none none

  Configuration register is 0 x 2102

  You need get the license of security feature to configure the IPSec VPN.

  Currently, you have 'none' for the security feature:

  ----------------------------------------------------------------
  Technology-technology-package technology
  Course Type next reboot
  -----------------------------------------------------------------
  IPBase ipbasek9 ipbasek9 Permanent
  security, none none none
  given none none none

  Here is the information about the licenses on router 1900 series:

  http://www.Cisco.com/en/us/partner/docs/routers/access/1900/hardware/installation/guide/Software_Licenses.html

• Help to configure SSL on router RV220W

  Hi I need help to set up a RV220W for SSL VPN router for my business. I never tried to do this before and have a lot of questions. Is there someone who would be willing to help me?

  Hello

  Thank you for your response.

  I'm sorry, what he seems to still be complicated, but let me tell you that it is quite normal, what is happening is that the browser recognizes not your public IP address or dynamic as a trusted site DNS name, so it will warn you that it may not be fixed, now, since you know it's your router then you can ignore the error and continue.

  The only way to get rid of the error is to buy a certificate from a certificate authority and add it to your router so that the browsers can recognize the safest site. Please keep in mind that it is not necessary for VPN SSL to work, you can just ignore the error and continue with the connection.

  Also, I forgot to mentioned this SSL VPN is compatible with Windows XP, Windows Vista and Windows 7 32-bit and 64-bit of Windows 8 operating system only is not supported.

  Please let me know if you have any other questions and don't forget to mark it as correct if it was useful for you, so that the other members of the forum can benefit from the information.

• SSL VPN from Cisco ASA and ACS 5.1 change password

  Dear Sir.

  I am tring configure ASA to change the local password on ACS 5.1. When the user access with ssl vpn if the ACS 5.1 password expiration date. ASA will display the dialog box or window popup to change the password. But it does not work. I'm tring to Setup with the functionality of password management on the SAA. When I enable password management it will not work and is unable to change the password. Could you tell me about this problem?

  Thank you

  Aphichat

  
  Dear Sir,
  I'm tring to setup ASA to change local password on ACS 5.1. When user access with ssl vpn if password on ACS 5.1 expire. ASA will show dialog box or pop-up to change password. But It don't work. I'm tring to setup with password management feature on ASA . When I enable password management it don't work and can't to change password. Could you advise me about this problem?
  Thank you
  Aphichat
  

  Hi Aphichat,

  Go to the password link below change promt via AEC in ASA: -.

  https://supportforums.Cisco.com/docs/doc-1328;JSESSIONID=A51E68318579261787BD60DDA0707819. Node0

  Hope to help!

  Ganesh.H

  Don't forget to note the useful message

• SSL VPN on Cisco ISR G2 license 2921?

  Hi, quick question.  We have a CISCO 2921/K9, who has all of the features securityk9 (reflects Permanent under show version)

  I thought including SSL VPN, but make a "show license all" it does not reflect that:

  J:: feature 4: SSL_VPN Version: 1.0

  License type: EvalRightToUse

  The license status: Active, in use

  The total period of assessment: 8 weeks 4 days

  Assessment period left: 8 weeks 2 days

  Used period: 1 day 5 hours

  Transition date: 11 January 2013 23:05:41

  Number of licenses: 100/0 (in-use/Violation)

  License priority: bass

  Can someone please provide some clarification?

  Thank you!

  -rya

  securityK9 does not include the SSL VPN license. This just activate the security features on the ISRG2, and you would need this license to run VPN SSL, and the SSL VPN itself license.

  Here is the URL for your reference:

  http://www.Cisco.com/en/us/docs/routers/access/sw_activation/SA_on_ISR.html#wp1151975

  To run SSL VPN, you must securityK9 and SSL VPN license.

• Order SSL VPN with Cisco Cloud Web Security

  We have implemented Cisco Cloud Web Security with the connector of the ASA and transfer all traffic port 80 and 443 to the Tower of the CCW. We have enabled HTTPS inspection, and I was wondering if there was anything, we can add in the configuration that would allow us to control (allow/block) SSL VPN?

  #Clientless SSL VPN is not supported with Cloud Security Web; don't forget to exempt all SSL VPN traffic without client service ASA for Cloud Web Security Strategy.

  Reference: http://www.cisco.com/c/en/us/td/docs/security/asa/asa90/configuration/gu...

• VPN router Cisco 2611XM VPN client

  I have 2611XM router on a Central site with two FastEthernet interfaces? XA; (FastEthernet0/0 and FastEtherne0/1). FE0/0 has private ip address?xa;192.168.1.1/24 and it connects on LAN 192.168.1.0/24. FE0/1A public? XA; address x.x.x.x/30 and his connects to Internet. There on this NAT router? XA; with overload. ? XA; This router is to give customers remote access with Cisco VPN client on? XA; Internet to the LAN and at the same time, the users local access to the Internet. ? XA; I did a config that establish the tunnel between the clients and the router but? XA; I can't ping all devices on the local network. ? XA; The router must also give remote access and LAN in the scenarios from site to site? XA;

  I can establish the tunnel between my PC and the router via a dial-up Internet connection. But when the tunnel is established that except my public IP address of the router, I can't ping any public IP address. I can ping all other customers who owns the ip address of the pool for customers.

  Addition of the sheep route map should not make you lose the connection to the router.

  Are the commands that you will need to put in

  access-list 101 deny ip 192.168.1.0 0.0.0.255 10.1.1.0 0.0.0.255

  access-list 101 permit ip 192.168.1.0 0.0.0.255 any

  sheep allowed 10 route map

  corresponds to the IP 101

  You need to delete translations of nat or remove commands 'ip nat outside' and 'ip nat inside' temporarily while you are taking the following off the coast

  no nat ip inside the source list 7 pool internet overload

  and add the command

  IP nat inside source map route sheep pool internet overload

  Make sure that you reapply the "nat inside ip' and ' ip nat outside of ' orders return of your internal users will not be able to go to the internet.

  You can search this config in the link that sent Glenn-

  http://www.Cisco.com/warp/public/707/ios_D.html

  I pasted the lines that you should look into setting up the example below

  ! - Except the private network and the VPN Client from the NAT process traffic.

  access-list 110 deny ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255

  access-list 110 deny ip 192.168.100.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 110 permit ip 192.168.100.0 0.0.0.255 any

  ! - Except the private network and the VPN Client from the NAT process traffic.

  sheep allowed 10 route map

  corresponds to the IP 110

  -Except the private network and the VPN Client from the NAT process traffic.

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  Thank you

  Ranjana

• To activate SSL license on cisco ASA

  Hello

  I ordered ASA with 50 ssl licneses.

  But due to the avialibilty of the product it shipping for me.

  I was delivered with the ASA with basic license is to say ASA - Bun - like SSL license K8.Then will take some time I was given a temporary license/activation key.

  Can someone let me know how to enable these licenses to begin work on SSL. My camera isn't in production right now.

  I will get permanent license in 3-4 weeks and still once I need it at this time here for the new license.

  Hope that the procedure would be more or less the same.

  Please guide.

  Reg,

  Sushil

  Sushil

  Check out this doc and come back if you have any other questions.

  Activation of licence ASA

  Jon

• Newbie Help Needed: Cisco 1941 router site to site VPN traffic routing issue

  Hello

  Please I need help with a VPN site-to site, I installed a router Cisco 1941 and a VPN concentrator based on Linux (Sophos UTM).

  The VPN is established between them, but I can't say the cisco router to send and receive traffic through the tunnel.

  Please, what missing am me?

  A few exits:

  ISAKMP crypto to show her:

  isakmp crypto #show her

  IPv4 Crypto ISAKMP Security Association

  DST CBC conn-State id

  62.173.32.122 62.173.32.50 QM_IDLE 1045 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  Crypto ipsec to show her:

  Interface: GigabitEthernet0/0

  Tag crypto map: QRIOSMAP, local addr 62.173.32.122

  protégé of the vrf: (none)

  local ident (addr, mask, prot, port): (192.168.20.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)

  current_peer 62.173.32.50 port 500

  LICENCE, flags is {origin_is_acl},

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

  #pkts decaps: 52, #pkts decrypt: 52, #pkts check: 52

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, #pkts compr. has failed: 0

  #pkts not unpacked: 0, #pkts decompress failed: 0

  Errors #send 0, #recv 0 errors

  local crypto endpt. : 62.173.32.122, remote Start crypto. : 62.173.32.50

  Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0

  current outbound SPI: 0x4D7E4817 (1300121623)

  PFS (Y/N): Y, Diffie-Hellman group: group2

  SAS of the esp on arrival:

  SPI: 0xEACF9A (15388570)

  transform: esp-3des esp-md5-hmac.

  running parameters = {Tunnel}

  Conn ID: 2277, flow_id: VPN:277 on board, sibling_flags 80000046, crypto card: QRIOSMAP

  calendar of his: service life remaining (k/s) key: (4491222/1015)

  Size IV: 8 bytes

  support for replay detection: Y

  Status: ACTIVE

  Please see my config:

  crypto ISAKMP policy 1

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  encryption... isakmp key address 62.X.X... 50

  ISAKMP crypto keepalive 10 periodicals

  !

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac TS-QRIOS

  !

  QRIOSMAP 10 ipsec-isakmp crypto map

  peer 62.X.X set... 50

  transformation-TS-QRIOS game

  PFS group2 Set

  match address 100

  !

  !

  !

  !

  !

  interface GigabitEthernet0/0

  Description WAN CONNECTION

  62.X.X IP... 124 255.255.255.248 secondary

  62.X.X IP... 123 255.255.255.248 secondary

  62.X.X IP... 122 255.255.255.248

  NAT outside IP

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  card crypto QRIOSMAP

  !

  interface GigabitEthernet0/0.2

  !

  interface GigabitEthernet0/1

  LAN CONNECTION description $ES_LAN$

  address 192.168.20.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  !

  IP nat pool mypool 62.X.X... ... Of 122 62.X.X 122 30 prefix length

  IP nat inside source list 1 pool mypool overload

  overload of IP nat inside source list 100 interface GigabitEthernet0/0

  !

  access-list 1 permit 192.168.20.0 0.0.0.255

  access-list 2 allow 10.2.0.0 0.0.0.255

  Note access-list 100 category QRIOSVPNTRAFFIC = 4

  Note access-list 100 IPSec rule

  access-list 100 permit ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 101 permit esp 62.X.X host... 50 62.X.X host... 122

  access list 101 permit udp host 62.X.X... 50 62.X.X... host isakmp EQ. 122

  access-list 101 permit ahp host 62.X.X... 50 62.X.X host... 122

  access-list 101 deny ip any any newspaper

  access-list 110 deny ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 110 permit ip 192.168.20.0 0.0.0.255 any

  !

  !

  !

  !

  sheep allowed 10 route map

  corresponds to the IP 110

  The parts of the configuration you posted seem better than earlier versions of the config. The initial problem was that traffic was not in the VPN tunnel. That works now?

  Here are the things I see in your config

  I don't understand the relationship of these 2 static routes by default. It identifies completely the next hop and a mask the bytes of Middleweight of the next hop. Sort of, it seems that they might be the same. But if they were the same, I don't understand why they both make their appearance in the config. Can provide you details?

  IP route 0.0.0.0 0.0.0.0 62.X.X... 121

  IP route 0.0.0.0 0.0.0.0 62.172.32.121

  This static route implies that there is another network (10.2.0/24) connected through the LAN. But there is no other reference to it and especially not for this translation. So I wonder how it works?

  IP route 10.2.0.0 255.255.255.0 192.168.20.2

  In this pair of static routes, the second route is a specific subnet more and would be included in the first and routes for the next of the same break. So I wonder why they are there are. There is not necessarily a problem, but is perhaps something that could be cleaned up.

  IP route 172.17.0.0 255.255.0.0 Tunnel20

  IP route 172.17.2.0 255.255.255.0 Tunnel20

  And these 2 static routes are similar. The second is a more precise indication and would be included in the first. And it is referred to the same next hop. So why have the other?

  IP route 172.18.0.0 255.255.0.0 Tunnel20

  IP route 172.18.0.0 Tunnel20 255.255.255.252

  HTH

  Rick

• Cisco 1941: no risk in "ip Routing" or "ip cef" for NetFlow when bypass

  Hello

  It's on a router Cisco 1941.  version 15.1 ipv4 only.

  I would like to enable Netflow v9 for use with PRTG bandwidth monitoring.

  I tried the instructions at http://kb.paessler.com/en/topic/563-do-you-have-any-configuration-tips-for-cisco-routers-and-prtg and the first step fails because I

  no ip Routing
  No cef

  in my running-config.  More precisely, this

   interface GigabitEthernet 0/1 ip route-cache flow exit 

  fails with the error message "ip Routing not enabled."

  I have read conflicting information on the question if I need to change one or both of these lines.  And I have enough to http://www.cisco.com/c/en/us/td/docs/ios/15_1/release/notes/15_1m_and_t/151-4MCAVS.html afraid to try just scanned.

  I hope that's enough of my config for someone to give some useful information.  Note the BYPASS.

  interface GigabitEthernet0/0
 no ip address
 no ip redirects
 no ip unreachables
 no ip route-cache
 load-interval 30
 duplex auto
 speed auto
 no cdp enable
 no mop enabled
 bridge-group 1
 bridge-group 1 spanning-disabled
!
interface GigabitEthernet0/1
 bandwidth 10000
 ip address 201.201.201.51 255.255.255.0
 ip access-group 110 in
 ip access-group 120 out
 no ip redirects
 no ip unreachables
 no ip route-cache
 load-interval 30
 duplex auto
 speed 10
 no cdp enable
 bridge-group 1
 bridge-group 1 spanning-disabled
!
ip default-gateway 201.201.201.1
ip forward-protocol nd
!
no ip http server
no ip http secure-server
ip flow-export version 9
ip flow-export destination 201.201.201.89 9991

  Looking forward to comments from a person with experience, do something similar.

  Thank you.

  We do not know anything about your environment or why you decided to activate ip Routing and fill. But there is probably a reason why you did that.

  The importance of this is that NetFlow data are generated as part of the routing decisions. And you prevent your router to make routing decisions as you have disabled ip Routing. So I don't see anyway that you can get this router NetFlow, as long you have disabled ip Routing.

  HTH

  Rick

• SSL VPN on ASA-

  Everyone,

  I went up to a SSL VPN router and now migrate to ASA firewall and was looking for a doc that documents the installation using the ASDM or CLI.

  Thanks for your help.

  Sheldon.

  These should contribute.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00808efbd2.shtml

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080975e83.shtml

• Cannot change the SSL VPN customization

  Hello

  I have ASA 5520 and activate SSL VPN

  I want to optimize my portal page, removing the "Cisco SSL VPN" and put my company name and logo.

  I created a new customization, but when click on Edit to change a wen page appears but the load.

  can someone help me?

  Concerning

  If you want to change the Cisco logo for your company logo, please follow this example configuration for personalization of Portal:

  Change the logo:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00808bd92b.shtml

  Change the title:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00808bd861.shtml

  Hope that helps.

• RVL200 - SSL VPN and firewall rules

  Forgive my ignorance, but I have been immersed in the configuration of this device RVL200 to allow Remoting SSL VPN to a customer site, sight unseen.  I have the basics of the VPN set up in config, but now move the firewall rules.  We want to block all internal devices to access the Internet, but I don't want to cripple the remote clients that will be borrowed by blocking their return via the SSL VPN traffic.  This leads to my questions:

  (1) a rule of DENIAL of coverage for all traffic OUTBOUND will prevent the primary function of the VPN (to allow the administration away from machines on the local network)?

  (2) if the answer to #1 is 'Yes', what ports/services do I need to open the side LAN?

  (3) building # 2, configuring authorized outbound rules apply only for VPN clients, rather than all the hosts on LAN?

  (4) as the default INCOMING traffic rule is to REFUSE EVERYTHING, do I have to create a rule to allow the VPN tunnel, or guess that in the configuration of the router?

  Here are some other details:

  • The LAN behind the RVL200 is also isolated LAN in a manufacturing environment
  • All hosts on this network have a static IP address on a single subnet.
  • The RVL200 has been configured with a static, public IP on the WAN/INTERNET side.
  • DHCP has been disabled on the RVL200
  • Authentication to the device will use a local database.
  • There is no such thing as no DNS server on the local network
  • The device upstream of the RVL200 is a modem using PPPoE DSL, and the device has been configured for this setting.
  • Several database of local users accounts were created to facilitate the SSL VPN access.

  I worked with other aspects of it for a long time, but limited experience with VPN and the associated firewall rules and zero with this family of aircraft.  Any help will be greatly appreciated.

  aponikikay, there is no port forwarding necessary to the function of the RVL200 SSL - VPN.

  Topic 1. That is not proven. It shouldn't do. The router should automatically make sure that the SSL - VPN router service is functional and accessible.

  Re 2. No transfer necessary. In addition, never before TCP/UDP port 47 or 50 for VPN functions. The TCP 1723 port is used for PPTP. UDP 500 is used for ISAKMP. You usually also to transmit TCP/UDP 4500 port for IPSec encapsulation.

  Let's not port 47. ERM is an IP protocol that is used for virtual private networks. It is a TCP or UDP protocol. GRE has 47 IP protocol number. It has nothing to do with TCP or UDP port 47. TCP and UDP are completely different protocols of free WILL.

  It goes the same for 50: ESP is the payload for IPSec tunnels. ESP is the Protocol IP 50. It has nothing to do with TCP or UDP port 50.

  'Transfer' of the GRE is configured with PPTP passthrough option.

  'Transfer' of the ESP is configured with IPSec passthrough option.