Help TV Input Device

Similar Questions

• Registering a dll file to start the service HID Input Device

  Hello

  I would like to register the dll located in my System32 hidserv.dll. However, when you enter the command 'regsvr32 hidserv.dll' I have an error message indicating that: "hidserv.dll was loaded, but the DllRegisterServer entry point was not found. This file cannot be saved. "

  How I then save it, knowing that I checked that this file is not corrupt?

  I need to register this dll in order to start the "HID Input Device" who stubbornly refuses to start despite an integrity check in the registry.

  The system event viewer specifies that:

  "HID Input Service service terminated with the error:
  Error 126: The specified module is not found. "

  I already tried to extract hidserv.dll, mouclass.sys & mouhid.sys sp2 and sp3 even to put them in the C:\Windows\System32 directory, but I had no change.

  The files I have place in my SYSTEM32 have the following version:
  Hidserv.dll: 5.1.2600.5512
  Mouclass.sys: 5.1.2600.5512
  mouhid.sys: 5.1.2600.0

  but the service still does not start even after rebooting. The 126 error continues. Is there other files to extract / expansion?

  I checked the integrity of all stakeholders key in the registry (for example, to have the "ServiceDll" key whose value is "% systemroot%\System32\hidserv.dll" in the settings of the service HIDserv ControlSets), but nothing more.

  I give you an export of the current CS:

  Windows Registry Editor Version 5.00

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HidServ]
  "DependOnService" = hex (7): 52, 00, 70, 00, 63, 00, 53, 00, 73, 00, 00, 00, 00, 00
  "Description"="allows generic inbound access to the user interface devices, which activate and maintain the use of the active buttons preset on the keyboard, remote controls, and other multimedia devices. If this service is stopped, the normal controlled active buttons not of will operate this service don't. If this service is disabled, any services dependent on explicitly will not start. »
  "DisplayName"="HIDDEN Service entry.
  "ErrorControl" = DWORD: 00000001
  "ImagePath" = hex (2): 25, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 52, 00, 6f, 00, 6f, 00,------.
  74,00,25,00, 5 C, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 D, 00, 33, 00, 32, 00, 5 C, 00, 73,------.
  00,76,00,63,00,68,00, 6f, 00, 73, 00, 74, 00, 2nd, 00, 65, 00, 78, 00, 65, 00, 20, 00, 2d, 00,------.
  6 b, 20, 00, 00, 6F, 00, 65, 00, 74, 00, 73, 00, 76, 00, 63, 00, 73, 00, 00, 00
  "LocalSystem ObjectName"=""
  "Start" =: 00000002
  'Type' = dword:00000020

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HidServ\Parameters]
  "ServiceDll" = hex (2): 20, 00, 25, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 52, 00, 6f,
  00, 6f, 00, 74, 00, 25, 00, 5 c, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 00, 32, 33, 00,------.
  5 c, 00, 68, 00, 69, 00, 64, 00, 73, 00, 65, 00, 72, 00, 76, 00, 2nd, 00, 64, 00, 6 c, 00, 6 c, 00, 00,------.
  00

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HidServ\Enum]
  "0" = "Root\\LEGACY_HIDSERV\\0000."
  "Count" = DWORD: 00000001
  "NextInstance" = DWORD: 00000001

  By analyzing the Observer newspaper of events more deeply, I could identify the date on which took place the first concern. The problem is dated, 18/08/2010 at 11:59:17 (it sticks with the conclusion of the first concern of losing control of my volume on my Logitech G110 keyboard also control buttons). I don't remember having a particular to this date on my system change, except perhaps a Windows Update automatically.
  I could not try a system restore, knowing that the RP oldest I have is dated 20/08, so downstream of the original problem.

  I ran a File Checker sfc/scannow system with my Windows XP Pro SP3 (current version of my system) installation cd. I've been thinking about it since a cd to install Windows XP Pro SP2, but better is worth twice more than once. I also realized a CheckDisk, but these two operations have not changed the problem.

  You will find export of address following my diary of events on the system.

  I have completed all of the tasks (start, replacement dll, see registry, SFC,...) while logged on sessions 'standard user', 'administrator' and even as a 'SYSTEM' (NT Authority), but in none of these configurations, it was possible for me to start this service. If I come to you, is precisely to avoid passing through a repair using the cd which would have made me lose a lot of time. I don't usually do the use of support services, in general the case has already been handled and the response or similar cases are on the web. But now I feel like in front of a technical impasse. I appeal to your specific skills to do what is necessary for good service restarting without using a remedy that eventually a reinstallation of the system.

  It you want to check my configuration, you can find it here.
  If you need more information, feel free to contact me. I would be happy to answer them.

  Until then, thank you very much. Kind regards.

  Arnaud TIERANT.

  First of all, the hidserv.dll is not a DLL that can be recorded.  You can try all day long, but it will not be because he is not on the list of DLLs that will be or must be registered.  There is a list, and which is not on it.  (well thought of).

  Your problem is in the registry with the HidServ, section ServiceDLL parameter.

  You have a space left in the key ServiceDLL.  In regedit, it should look like this:

  %SystemRoot%\System32\hidserv.dll

  Yours probably looks like this in regedit:

  %SystemRoot%\System32\hidserv.dll

  See the space left?  I don't know how it got that way (perhaps something that was installed for these humans), but I know that if I put a space in front of me and restart my system, HID service not start and give me an error 126 as you describe.  He has no idea about the problem in the log events.

  With space on the left, the specified module really not found because there is no such thing as the path (with the space to the left).

  Your registry export reveals this problem.

  Yours looks like this:

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HidServ\Parameters]
  "ServiceDll" =hex (2): 20, 00, 25, 00,53,00,79,00,73,00,74,00,65,00, 6 d, 00, 52, 00, 6f,
  00, 6f, 00, 74, 00, 25, 00, 5 c, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 00, 32, 33, 00,------.
  5 c, 00, 68, 00, 69, 00, 64, 00, 73, 00, 65, 00, 72, 00, 76, 00, 2nd, 00, 64, 00, 6 c, 00, 6 c, 00, 00,------.
  00

  It should look like this:

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HidServ\Parameters]
  "ServiceDll" =hex (2): 25, 00,53,00,79,00,73,00,74,00,65,00, 6 d, 00, 52, 00, 6f,
  00, 6f, 00, 74, 00, 25, 00, 5 c, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 00, 32, 33, 00,------.
  5 c, 00, 68, 00, 69, 00, 64, 00, 73, 00, 65, 00, 72, 00, 76, 00, 2nd, 00, 64, 00, 6 c, 00, 6 c, 00, 00,------.
  00

  In your, you can see I have stuff in bold print on the front of the chain: 20.00...  In hexadecimal, is a space and a null value (null value is correct).  You must use regedit to get rid of this leading space (20 hex), and don't forget that, in the settings section, the first character of the value ServiceDLL is the % sign (which is a hexagon of 25).

  You can, of course, just change the string, delete everything that is there, and retype the value if it looks like this without spaces attack/crawling:

  %SystemRoot%\System32\hidserv.dll

  The HID Service will not start if you come to make the changes and try to start the service.  After making your changes, you need to restart, you can check it out, and then start the service HID.

  Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

• Cannot open the input device. Another program, it may have already. RC = - 10 (Ventrilo)

  
  

  • Duuring the time I downloaded Ventrilo, I was getting rather annoyed with it. I can't speak to members of my Guild felloe that this error message keeps popping up, to open the input device. Another program, it may have already. RC = - 10... Ive asked them suggestions, but all I received didn't come clear to solve the problem...

  I use a headset called Gembird AP-870. I searched the web, trying to find a solution but have not found anything that can help me... If anyone knows how I can solve this problem I will be grateful...

  It is located directly above the ORB start and said in fact start search inside.

  If you can't find it always, hit the Windows key and R at the same time to open run and type msconfig.exe, and then enter.  As you will get to the same place.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• input device touchscreen usb disabled and now the device disappeared

  To summarize for those who want a short version:

  Model: Sony VAIO Duo svd11225cxb

  Windows 8.1

  a. my touch screen of this device is * outside? Any way to reinstall the driver for the touch screen? Tech Sony said that the material is very good.

  b. in my efforts to solve the problem, I turned off a device in Device Manager and it now gone, no way to recover?

  Here is the full version:

  I have a Sony VAIO Duo svd11225cxb. After the recent updates, freaked out and kept touch screen back to the menu screen to start (and possibly other areas of the screen).

  We decided that so that the computer to operate, it should disable the touch screen. So we went to the Device Manager and disabled the "usb input device" under "human interface devices" which associated with the touch screen. Allow us went then back to him and found that the unit had disappeared from the Device Manager. I tried to install the next window touchscreen driver, but that did nothing. Any advice?

  Hi herschen,.

  Welcome to the community of Sony!

  Perhaps the question is just the driver. We will isolate the problem by following these steps:

  • Power cycle - turn off the laptop-> flip the unit and look for a button cell or a pin hole on the bottom of the laptop. Using a safety pin, press and hold the hole for 5 seconds.

  

  • Reset the BIOS to the
  • Go to Device Manager -> right click and Uninstall the driver/s under Human Interface Device (DO NOT REMOVE). Then restart the unit. The driver will be reinstalled.
  • Run the Windows Update and Vaio Update.

  Hope these helps.

  Kind regards

  Vincent

  If my post answered your question, please mark it as "accept as a Solution.

• Opening Don t see a camera as input device

  I like to transfer pictures from my camera, a V - LUX (Type114) of Leica at the opening, but the software has not shown this input device

  Jurgen,

  What have you already tried?

  The camera shows if you open the import in the opening panel manually by entering ⌘I?

  You try to read directly from the card or is the camera connected by a USB cable?

  Try if the card can be read, if you use the card reader.

  The device is fully charged or connected to a power source?  Is the camera in the right mode to connect to the computer?

  Other applications see the camera?  Photos for Mac? Image capture?

  Have you tried, if the opening is to see the camera, if yo use another card?  Any camera sees opening?

• Not found audio input device

  When you record a voice on the audio input device says iphone not found. In the micro-life the iMovie app does not appear. What should do?

  Thanks Pierre

  Hello Peter,.

  Thank you for using communities of Apple Support.

  I see that your internal microphone is not recognized in iMovie on your iPhone.  I want to start that you please leave the app iMovie and then restart your iPhone.

  iOS: force an app to close

  Turn your device iOS market (reboot), then reset

  Take care.

• How to synchronize the device with an analog input device?

  Is it possible to synchronize a device (e.g. Basler scA640-70fm, IEEE 1394 b or NI 1722 smart camera) with an input device analog (for example, NI PCI/USB-6225 or NI PCI/USB-6255)?   For example, it is important to a video image of match with a sample of data digitized by the A/D converter.   In particular, it is important to know when the first video image starts compared to samples of digital data.   If it is possible to synchronize the camera with the A/D device, then then how is it?

  Thank you

  Ian

  Hello Robert,.

  Thank you for reference and information.

  Ian

• N5902 Input Device works not when the Dongle is attached directly to the USB Port of the 3.0

  It's a big problem because the port only 2.0 on my Lenovo Yoga 700 is also used for charging and unless I'm on battery so I have to fix the dongle because otherwise the USB device is not recognized and I can't use my N5902 input device. Someone has an idea, a driver so I can install it manually? I use Windows 10.

  I managed to find a solution, I applied "Solution 2" of https://www.drivereasy.com/knowledge/fix-issue-after-upgrade-system-to-windows-10-usb-ports-don ' t - wor...

• Try to install USB hub, error: device driver software was not successfully installed. Please consult the manufacturer of your device to help get this device installed.

  Software device driver has not been installed successfully. Please consult the manufacturer of your device to help get this device installed.

  Failed. Generic USB hub.  I went to the Device Manager and clicked on update, but it did not work. Can you help me.

  original title: DEVICE DRIVER has NOT been INSTALLED successfully.

  Go to your computer manufacturer's support web site and search for the Windows Vista drivers for your specific model number.

  If there are drivers Windows Vista, then to download to a folder on your hard drive and install all of them, in starting with the card mother/chipset drivers SATA, LAN, Audio, USB, Etc., and so on.

  List of computer manufacturer support sites:
  http://Windows.Microsoft.com/en-us/Windows/help/contact-support/computer-manufacturers

  If you have an Intel motherboard, you can try the Intel driver update utility: http://www.intel.com/support/detect.htm?iid=dc_iduu

  Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems

  Graphics/video drivers:
  Check the download site of the manufacture of the graphics card for the latest Windows 7 / Vista drivers for your card.
  ATI: http://support.amd.com/us/gpudownload/Pages/index.aspx
  NVIDIA: http://www.nvidia.com/Download/index5.aspx?lang=en-us

  J W Stuart: http://www.pagestart.com

• Input device multimedia video controller/PCI Windows 7

  Multimedia video Controlloer and PCI input devices have a yellow question mark in device, "other devices Manager."
  I can do something to solve this problem. I'm not sure what kind of video card, it is, but I think its Nvidia p300 is what it says on the card when I looked...
  Then when I go to download a driver from nvidia, they say, I already have the update drivers... I do not understand

  Information on the site with this driver:
  
  Supported operating systems: Editions 32-bit and 64-bit Windows 7 RTM / Vista SP2 / SP3 of XP

  If you want to say thanks to someone just click on Vote as useful (i.e. under each avatar of the user).

  If your issue is resolved, please indicate then your wire is with solution.

• need a pc input device driver

  Hello, I am on Windows 7 and does not have a driver for device entry for PC, I bought a program that detects all the drivers, but he can't find one for this one! Can someone please advise how I can get this driver? I have a new sound card, but still he did not make a difference.

  Any suggestions would be much appreciated

  See you soon

  Tori

  "pc input device" could mean anything, when exactly you see an error message?

  Driver finder so paid or free programs should not be used as they can and are causing problems.

  Drivers for your PC are available for free since your assumption of the manufacturers of PC, or for a generic desktop by the creators of individual materials

• I have a VIA card mother U8668-D and in Device Manager it is said that the "Multimedia Audio Controller", "PCI input device" and "PCI Simple Communications controller" function.

  I have a VIA card mother U8668-D and in Device Manager it is said that the "Multimedia Audio Controller", "PCI input device" and "PCI Simple Communications controller" function. I posted a link to the image below.

  Nevermind, I deleted the image by accident. Oops.

  https://SkyDrive.live.com/redir?RESID=D50158D65A52CBBA! 1928 & authkey =! AKdLQ4hGMOynvnc

  If the manufacturer of the motherboard doesn't provide drivers specific win7 there is none.

  If there is the bit Vista drivers ' appropriate ness, what they would usually work

• No available on don't Aspire X 39990 Audio input device

  I use Adobe Audition and when I tried (for the 1st time) to record speech from the internet it says "Default Input (no device available). Is there something that does not work or I have to download something that I could record from the internet on all the other machines of Acer I've had.

  I looked on all available inputs and can not see anything obvious

  Thanks a lot for your help

  Unfortunately, we are unable to support Adobe Audition, then I wouldn't be able to speak directly to this software configuration.

  I suggest only to define the input as your sound card device, since you have incoming audio from the ' net.

• Help, please! Device drivers system & basic coprocessor are missing after Win7 upgrade

  Please help with under drivers

  Model - dv9500

  (1) system base unit

  Bus 2 PCI, device 5, function 3

  Hardware - PCI/VEN_1180 & DEV_0592 & SUBSYS_30CF103C & REV_12 ID

  (2) system base unit

  Bus 2 PCI, device 5, function 2

  Hardware - PCI/VEN_1180 & DEV_0843 & SUBSYS_30CF103C & REV_12 ID

  (3) coprocessor

  PCI bus 0, device 1, function 3

  Hardware - PCI/VEN_10DE & DEV_0534 & SUBSYS_30CF103C & REV_A2 ID

  Thanks in advance!

  It is always helpful if you post the full product name or product number. You can find it by removing the battery and looking for the label that says p/n. display the string alphanumeric full here in your thread.

  Have you looked into the system of operating systems section in guides stickied for that information?

  Take a reading this post by Member Daniel_Potyrala. Read the latest pages for locations of tutorial and driver.

  #1 is a Ricoh card

  #2 is the Ricoh storage controller

  Your #3 is that a driver Intel Core 2 coprocessor not installed n not question.  Go to the driver download Intel Web page. Find the correct driver from the OS for your chipset/processor and install it.

• Help, why no device after installing win 7 on new E5-411 showing?

  Recently, I brought an E5 Aspire-411, in Thailand, with a Linpus Linux operating system. I installed my favorite OS Win7 x 64. I managed to install the hardware drivers. The strange thing is that there is no bluetooth device in Device Manager. Is this because (a) there is no adapter b/tooth on this model, (b) the adapter is defective, (c) I need to install a driver to activate or others? I took the things according to my limited knowledge, I hope someone can help to answer this question.

  Ironfly, I solved the problem. The only way to do was install win 8.1 for evaluation. Now there are bluetooth devices where they should be in "Device Manager". And everything works a lot better than when I had win 7 there. I learned the hard way that the hardware and the latest drivers are not compatible with win 7, anyone trying to install on the model of victory 8 support will have no problems, things not working not properly or not at all. I hope this helps others, the time to move from win 7 I think, and hey 8.1 is not so bad really... Thanks again, cheers.