help with a broken drive install...

Similar Questions

• 445 G1: need help with AMD video driver install

  Hello everyone.

  What drivers I don't sellect support AMD Web site? Some can give me the link for my product.

  Specifications:

  APU AMD 4500 M WITH AMD RADEON 8750 M + AMD RADEON 7640 G (this is the graph of low power)

  Or should I JUST install drivers from the HP site? Thank you very much for your help!

  APU (Chipset AMD drivers)

  Open the "optional downloads" from the displayed link

• Performance index Windows CPU drops with new hard drive installed on Windows Home Premium 64 bit.

  Hello world. I have a Toshiba laptop with Win 7 Home Premium 64-bit. 1 GB of GPU, 6 GB of ram, Intel i7 Q740 1.73 GHz. operating system has been pre-installed.

  The old hard drive was 600 GB 5400 RPM 8 MB Cache. The new disk of 1 TB 7200 RPM 32 MB Cache. With the old drive the cpu had index of the 7.1. With the new disc, he fell to 5.6. all the other components even rated the two discs. Both discs have a 512th form. Searched everywhere for an answer and would like an answer, cause im very curious and puzzled. Health perfect new drive using disk setiniel and crystal HD... info old drive had bad sectors, but cpu always valued at 7.1. If someone can answer, I would be very grateful.

  SV

  WEI is a completely arbitrary number and because it has been eliminated in the 8 win & win 10.  I would not be concerned about the number unless your computer is actually slower.  Your hard drive has nothing to do with the rating of the CPU.

• Help with error: "display driver stopped responding, but recovered."

  Hello

  First of all, my configuration is a Dell XPS 7100, Windows 7 Home Premium 64-bit, the Videocard Visiontek AMD Radeon HD 6850 w / 9.2.0.0 driver version.

  AMD Phenom II X 6 cpu.

  My problem is that when I try to play a game (more precisely: Minecraft, SimCity, World in Conflict, AOE3) under Windows, the screen freezes for 5 seconds then go black for 1 second then back to the top with an error message saying:

  Display driver stopped responding, but recovered

  Driver AMD display driver stopped responding and has successfully recovered.

  This started only after I upgraded my video card to an AMD HD 5670 to an AMD Radeon HD 6850 Visiontek, which, at the same time, I upgraded my power supply to a 500w unit as AMD recommends. After that that I've updated all my drivers, deleted and reinstalled the driver video and which did not help. I then searched in all the forums about this problem and found that it is more than likely a problem with Windows power management. So, I followed the instructions on the site to change the registry data to help with this. This did not work, the same problem at the same time. I then contacted AMD Support and fairly well, they told me that it is either the power supply or windows power management which was the cause of the crash.

  I am at a loss now, I know not what to do. I have not tried all the third-party programs to try to manage the power. But if someone has used one that works or has any ideas for me to try please let me know.

  Thank you very much!

  I found a solution that helps!

  Please make a backup of the registry before making any changes in it.

  When editing the registry go to:

  • HKEY_LOCAL_MACHINE
  • then the MATERIAL
  • then DEVICEMAP
  • then the VIDEO
  • in the 'VIDEO' file, there is an entry with the title: MaxObjectNumber - REG_DWORD
  • This has a value at the end that looks like 0 x 00000006 (6) or 0 x 00000005 (5)
  • Double-click MaxObjectNumber, and an edit box appears
  • put 0 in the given value, and then click OK.

  This will disable Windows GPU Timeout detection and recovery. That she has stopped crashing on me.  The only problem is that windows does not save it and it resets after that rebooting so it must be changed every time you start the computer.

  If anyone knows how to save the changes to the registry, I would be very grateful for your advice.

• Qosmio G20-139: need help with 2nd HARD drive installation

  Hey fans of tosh.

  I got a Qosmio G20-139 and I want to install 2nd HARD drive. How can I go about it? I don't want to mirror the 1st HARD drive I just that it runs as a HDD separated for more storage. How do I set up and format?

  I'm using WXP MCE any help received with gratitude, keep in mind, I'm no expert actually I'm a fool to the village that of been inbreeding so take me through in easy to understand steps that even I can follow.

  Cheers in anticipation

  StevieB

  Hello

  That s just to change the BIOS settings in the BIOS!
  I think that the BIOS settings are placed in the last page of the BIOS (3).

  Try setting the 1RAID-0 on the first HARD disk and the 2RAID-0 the second HARD disk.

  It worked well on my laptop.

  By the way; information on the RAID configuration found in the user manual.

  Have a nice day ;)

• need help with USB controller driver

  Recently downgraded to windows 8 for windows 7 ultimate, installed all the drivers except that I can't find the driver for the USB controller anywhere. Will not find the drivers automatically on the internet. I guess I have to install the chipset for PC.  Cannot download from the HP Web site because I got demoted. .  .

  Its a HP Pavilion model 500-098 with windows 7 ultimate 32 bit

  Any help would be appreciated

  Thanks for your time, Dale

  You are the very welcome.

  We'll get it to work... you definitely need the driver of the TI USB controller.

  Download, but do not run the file I posted.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=CP-100633-1&cc=us&DLC=en&LC=en&JumpID=reg_r1002_usen_c-001_title_r0002

  Download and install this free utility for files.

  http://www.7-zip.org/

  After installing 7 - zip, right-click on the downloaded file and select 7 - Zip option in the list.

  Have 7-Zip extract of: and let it extract the file in the name of the folder (sp55506).

  After 7-zip created the driver folder, go to Device Manager and click on the device of USB controller requiring driver.

  Click on the driver tab, click on set to update driver.  Select her browse my computer for driver software option and find the driver 7-Zip created folder.

  Make sure that the include subfolders is selected and see if the pilot goes like this.

• Help with 5.5 nested install please - "the logs are stored on non-persistent storage..." »

  Hi all

  I must be missing something as my nested installation keeps failing.  I did that before, but with older versions.  I have a DellC6100 with L5639 CPU and 48GB of RAM.  I have configured the virtual computer as long as need HW v10, check mark "expose hardware virtualization assisted...» "with him 2 x CPU with 2GBRAM. The disc, I added was the drive by default 1 GB LSI Logic parallel.  This is the sequence of events after starting:

  

  

  

  Nothing after that... Any suggestions as to what it could be please?  I tried different versions of 5.5 and also a vDisk IDE.  Google is not much help...

  My pHosts are running on 5.5U2.

  Thanks in advance!

  Wikus

  This is not a failure.  Looks like if you pressed Alt + F11 instead of F11.  Press Alt - F2 and you should be able to continue the installation.

• Need help with replacing a drive on a virtual machine

  Test case for something I need to do on a separate production machine.  Virtual MACHINE is running WinSvr2003.  Only the hard disk assigned to the virtual machine is one of 20 GB disk, C: using this.  Need to C: to be larger.  Add a 40 GB drive to the configuration of the VM in the CR.  Started an iso BartPE with plug-in in Ghost.  Ghost can copy the C: 20 GB drive on the 40 GB drive.  Went in the VM config and changed is the 40 GB SCSI 0.1 drive and the drive of 20 GB at SCSI0, 2.  After I saved, VMware changed the 40 GB on disk 1 and the 20 GB on disk 2.  Went it into the BIOS on the machine config to boot the disk of 40 GB.  But no matter how I put it in the BIOS, it would only start on the 20 GB drive.  Went in the VM config and removed the 20 GB drive (which is not an option on the production machine, it has a volume of data on the same drive).  It boots to Windows, so I guess it's start on the 40 GB drive.  But I am unable to connect to it.  It shows that the application of settings, record the settings, then back to the login screen, all within 2 seconds approximately.

  Is there anything else I need to do to (1) move the volume from the Windows system to a new disk w without side effects in Windows and (2) so that it can start on the new disk correctly?

  If it is a single virtual drive with 2 partitions and the C:\ is on the front of the drive, Extpart won't help. It is usually best to separate the partitions to multiple virtual disks. I use the converter to V2V the VM and move on their own virtual disk partitions, then develop them if necessary.

• Old laptop - Pro 490 - need help with the graphics driver for Win 98

  I downloaded the display drivers, but these seem to be the same ones that Windows 98 is installed but the screen is not 'full' but just a window in the middle of the screen.

  I have also 1 device that does not have a pilot.

  Is someone can you please tell me where I can get a set of drivers for the laptop? Win98SE drivers seem to be a little short on the toshiba web site (unless I'm blind)

  Otherwise I'll have to use the recovery CD to install windows 95 and then upgrade to windows 98... do not look forward to that.

  Any help greatly appreciated

  Hello

  In my view, the drivers for Win98 and Win 98SE are the same.
  But this unit is very old and Toshiba doesn't conceive these drivers more.
  I suggest to look on the sites of manufacturers of equipment. Maybe you'll find some drivers for Win98

  Concerning

• 4540 proBook s product ID C9K7O: I need help with network controller driver installation.

  I had to install Windows 7 Premium 64-bit operating system and the network controller was not recognized and therefore, the drivers were not installed. That's what I see in Device Manager:

  PCI\VEN_168C & DEV_0032 & SUBSYS_1838103C & REV_01
  
  PCI\VEN_168C & DEV_0032 & SUBSYS_1838103C
  
  PCI\VEN_168C & DEV_0032 & CC_028000
  
  PCI\VEN_168C & DEV_0032 & CC_0280

  I got a driver to download from technical support, but that it does not recognize the controller either. Reference case # (deleted content)

  Dad.

  Have you tried this one?

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5229456 & swItemId = ob_128686_1 & swEnvOid = 4059

  REO

• Satellite L955-10f - need help with uninstall Win8 and install Win7

  I'm now totally fed up with the Mickey Mouse Windows 8 OS and want to return to Windows 7. I have a new laptop Toshiba Satellite L955-10f. Should I use the recovery disk to get rid of W8?

  Is there a way I can get a recovery for W7 for this machine disk in case it is needed in the future? I'm not technical, so any help will be appreciated.

  Thanks in advance.

  Right there is big problem with this machine. I ve checked the download page of Toshiba and this model is not supported for Win7, it will be difficult to find the right drivers, tools and utilities.

  This model is designed for Win7 Toshiba doesn't offer Win7 recovery disc.
  This is a rather complicated situation. The first thing you need to do should now create Win8 recovery media using the preinstalled Toshiba Recovery Disk Creator.

  I put t know what to say. Maybe you have someone with an excellent knowledge of PC and who can help you with this. Material of your machine should be compared with other models may be supported, so you will be able to use the drivers, tools and utilities available for these models.

• Pls help with the audio driver

  Hi, I have a Fujitsu Siemens amilo pro v2065, when I installed win7 was not sound, I tried several drivers but failed. the sound chip is AD1986A on Intel 915 pm here's a link to the datasheet:
  I'd appreciate any help really
  Thank you

  http://social.answers.Microsoft.com/forums/en-us/GettingReadyforWindows7/threads

  Link above is "Preparing for Windows 7" Forum.

  http://social.technet.Microsoft.com/forums/en/category/w7itpro/

  Link above is Windows 7 Forums.

  Windows 7 questions/answers/suggestions should be directed there.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• Help with external hard drive

  I use an external hard drive Seagate for my photos and I have been use for more than a year, today when I used it, my windows 7 laptop not recognize it so I couldn't see the files but I knew that it worked as I could hear, I then plugged in a computer laptop windows 8 and it's the same thing. I used another cable, still nothing has changed. Could someone tell me how to solve this problem that I don't have a return to the top of the images.

  Hello

  This is a problem because it is not recognized by Windows 7 or Windows 8 machines.

  I would try it on a 3rd machine, such as pointing to something to go wrong with this Seagate HD.

  And hearing that HD is not a good sign either.

  See you soon.

• Help with the new APEX install

  I'm new to APEX and I try to get the initial installation work.  I have a front end server with WebLogic and Restful Services and a Server backend with oracle 12 c and APEX 5.01.  I've deployed the files ords.war and i.war on the server weblogic and ADR.  I just want to get to the login page.  I tried http://127.0.0.1:8080 / ADR and I get a Web page that displays "ORACLE REST DATA SERVICES" at the top and then you got a 404 error.  In the rest of the data services windows it shows "WARNING: the pool_config view or table is not found in the schema: APEX_LISTENER" ideas that I missed? »»

  Hi, reduction,

  Please provide the following information which will help to report the problem:

  • Oracle APEX retail version
  • Version of Oracle database in detail
  • ADR retail version
  • Version of Java EE application server support detail (if you use one)
  • Version of the JDK detail

  NOTE: Here "Retail" means the major + minor version. For example Application Express 4.2.4.00.08

  For debugging this problem, you face on ADR:

  • Find the folder of configuration of ADR.
  • Enable debug tracing in defaults.xml (if the entry is not there add the entry)
  • Turn on detailed error messages ask in defaults.xml (if the entry is not there add the entry)
  • Start(Re-Start) Oracle Weblogic Server.
  • Go to the URL of the APEX
  • Copy / paste the debug log in the response to the forum. (The error is usually at the end of the paper, paste/fix the whole journal where occurs the first exception)

  About 404 - when setting up ADR 3.0 have you skipped configuration "PL/SQL gateway '? (This step refers to the configuration of Oracle APEX with ADR (APEX_PUBLIC_USER configuration) which is required for the operation of Oracle APEX with ADR)?

  Otherwise, you will run into the following error message:

  • Re: Re: ADR 3 404 error
  • Re: problem with ADR 3.0

  Also open your "ords.3.0.1.177.18.02" folder and run the "readme.html" file in a browser and go to the section "404 errors when Oracle configuration REMAINS Data Services" on the causes of 404.

  Kind regards

  Kiran

• Help with a hard drive for 530 s

  I just got a Maxtor 500 GB SATA II / 300 hard drive internal & I want to install it.

  Someone told me this will not work in my computer, my computer will not accept SATA I have.

  It was the last in the store & I took it-I didn't know if he wanted for himself.

  It is good or bad?

  I have an Inspiron 530 s.

  It is also possible to get an external hard drive enclosure & put the disk in it & use it as a disk on my computer - I am the eye on the Antec MX-1

  Your advice is appreciated.