Help with the VLAN and RVS4000

Similar Questions

• Help with the VLAN on SG200-18 and two switches SG200-08

  Hello world. My apologies, but I'm only average at best with my CISCO skills. I have simple installation running some network devices connected via 3 CISCO switches. It is small office and two bedrooms - one with the servers and the other with the printer and pc. Each room has 8 ports SG200-08 pass.

  Router / firewall is Sonicwall TZ215 and manages the internal routing between VIRTUAL networks. Each SG200-08 was directly connected to TZ215 (no SG200-18 again) and VLAN worked perfectly. Please see diagram below...

  Problems started when I added in the Center SG200-18 more to handle additional devices. Everything that I'm doing wrong, but I can't do VLAN longer works. Something I won't set up correctly in SG200-18.

  Please help me to Setup VLAN here - tag, unidentified, PVID, trunk... I am completely lost and already had to reset SG200-18 twice.

  My work without port switch 18 Setup was like that.

  SG200-08 (1)
  G1 1 trunk 1U, 100 t
  G2 1 trunk 1U
  G3 1 trunk 1U
  G4 1 trunk 1U
  G5 1 trunk 1U
  G6 1 trunk 1U SERVER3
  G7 trunk 100 100U SERVER1
  G8 trunk 100 100U Server2

  SG200-08 (2)
  G1 1 trunk 1U, 50 t, 200 t
  G2 1 trunk 1U
  G3 1 trunk 1U
  G4 1 trunk 1U PC1A
  G5 1 trunk 1U PC1B
  G6 trunk 50 50U PC2A
  Trunk PC2B 50 50U G7
  NETWORK PRINTER for the 200 trunk 200U G8

  Thank you in advance.

  VLAN.jpg

  

  Hello

  Oh I'm sorry. I understand that you have 3xSG200-08 and 2 of them with the same configuration :-). So no need to use this port for now.

  Kind regards

  Aleksandra

• Helps with the rv180w and the Shrew soft vpn

  Hi, I'm trying to establish a vpn connection by using soft shrew for the cisco rv180w router.

  I watch and read everything I could find, but the connection drops during the opening of the tunnel.

  There were a few tuttorial here in the forum, but the links are down.

  I want Edifier is to establish communication and to be able to access my domain on the network.

  Any help with the settings would be greatly apeciated. I am new to vpn.

  Thanks in advance.

  Federico,

  Try to access the following link. It has good instructions for a similar model. The main difference is that the SA500 has double-WAN and the RV180W does not work.

  https://supportforums.Cisco.com/docs/doc-9378#comment-7216

  Here's another tutorial for the RVS4000 that can help:

  https://supportforums.Cisco.com/docs/doc-18443

  Check out the last post in the following thread, which received instructions for the RV220W (should be exactly the same as RV180W)

  https://supportforums.Cisco.com/message/4165652#4165652

  -Marty

• Help with the VLAN routing

  I'm pretty green when I just went and routing configurations please bear with me.  I'm available what I want to achieve and what I could do until now (although it may be completely wrong).

  I have an office where we run low on IP addresses for our local network, the obvious answer is to get VOIP phones on their own subnet.  So, I have a switch PC6224 I want to use to create the second subnet.

  Existing Workstation LAN = 172.22.144.0 (255.255.255.0)

  Default GW for the LAN = 172.22.144.1 for all devices on that subnet

  I would like to create an IPPhone = 172.22.145.0 (255.255.255.0) subnet

  Here's what I have "Achieved" so far:

  Currently, I can ping from a client on 172.22.145.x to the 172.22.144.12 (VLAN 3 ip interface) but cannot ping any other 172.22.144.x that is not directly connected to the 6224 switch device.  Trying to ping the network 172.22.145.x device leave a device plugged into the 172.22.144.x VLAN on the switch of packets results was sent to the default gateway for the network (172.22.144.1) who does not know what to do with them.

  Here is my config of 6224 switch operation:

  Console execution #show
  ! Current configuration:
  ! Description of the system "PowerConnect 6224, 3.3.6.4, VxWorks 6.5.
  ! 3.3.6.4 system software version
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 2-3
  VLAN 2 1 routing
  VLAN 3 2 routing
  subnet of VLAN association 172.22.144.0 255.255.255.0 3
  subnet of VLAN association 172.22.145.0 255.255.255.0 2
  output
  battery
  1 1 member
  output
  IP address no
  IP routing
  IP route 0.0.0.0 0.0.0.0 172.22.144.1
  interface vlan 2
  name "IPPhone.
  Routing
  IP 172.22.145.1 255.255.255.0
  output
  interface vlan 3
  name "TWLAN".
  Routing
  IP 172.22.144.12 255.255.255.0
  output
  level of 746f7a78621059d80fdc538acc40cbf2 user name 'admin' password encrypted 15
  !
  interface ethernet 1/g3
  switchport access vlan 3
  output
  !
  interface ethernet 1/g4
  switchport access vlan 3
  output
  !
  interface ethernet 1/g5
  switchport access vlan 2
  output

  !
  interface ethernet 1/g6
  switchport access vlan 2
  output
  !
  interface ethernet 1/g7
  switchport access vlan 2
  output
  !
  interface ethernet 1/g8
  switchport access vlan 2
  output
  !
  interface ethernet 1/g9
  switchport access vlan 2
  output
  !
  interface ethernet 1/g10
  switchport access vlan 2
  output
  !

  interface ethernet 1/g11
  switchport access vlan 2
  output
  !
  interface ethernet 1/g12
  switchport access vlan 2
  output
  !
  interface ethernet 1/g13
  switchport access vlan 2
  output
  !
  interface ethernet 1/g14
  switchport access vlan 2
  output
  !
  interface ethernet 1/g15
  switchport access vlan 2
  output
  !
  interface ethernet 1/g16

  switchport access vlan 2
  output
  !
  interface ethernet 1/g17
  switchport access vlan 2
  output
  !
  interface ethernet 1/g18
  switchport access vlan 2
  output
  !
  interface ethernet 1/g19
  switchport access vlan 2
  output
  !
  interface ethernet 1/g20
  switchport access vlan 2
  output
  !
  interface ethernet 1/g21
  switchport access vlan 2

  output
  !
  interface ethernet 1/g22
  switchport access vlan 2
  output
  !
  interface ethernet 1/g23
  switchport access vlan 2
  output
  !
  interface ethernet 1/g24
  switchport access vlan 2
  output
  output

  Console #.

  Any help would be greatly appreciated.

  Thanks, Grant

  What port connects to 172.22.144.1 the jump according to the internet?

  What should happen is we need a VLAN 'remote' separate just for the connection between the 6224 and your 172.22.144.1 jump following the internet device.

  If 172.22.144.1 remains the same, then you must create another local network VIRTUAL to "TWLAN".  Eventually, VLAN 4 with a range of ip addresses of 172.22.146.1 - 254 255.255.255.0.  Where the VLAN 4 interface has an IP address defined as 172.22.146.1.  Once that all connected devices again VLAN 4 that were in the VLAN 3 need to change there IPs and gateway 172.22.146.1

  So the only port that has configuration of VLAN 3 is the connection to 172.22.144.1 port next to the internet break.  The IP address defined on the interface VLAN 3 should be in the same subnet as 172.22.144.1 range.

  Here is a diagram that can help you to see the whole upward.  VLAN 100 in the diagram represent VLAN 3 in your case.  Switch 2 would represent your device from the internet of next hop.

  

• Need help with the formatting and reinstalling windows

  Hi, I have a Compaq Presario C700 p/n GR598EA #ABU I got to work about 3 years ago.

  Recently, it does not load windows, even in safe mode and I can't get back either.

  I used a disc to boot from linux to access and backup of all my important files and now I want to reformat the hard drive, resintall windows and start over (or try something else which will fix it)

  The laptop has been pre-installed with Windows Vista and HP stuff had already installed on it.  I don't have a Windows disc or discs of driver with the laptop.

  How can I format and reinstall windows and drivers, if I don't have records?

  Help, please.

  Thank you.

  Hello:

  You can order a Vista recovery disk set for your laptop if they are still available. See the instructions below:

  http://support.HP.com/US-en/document/c00810334=

  If you live not in the US or the Canada, you can contact HP Support worldwide for the country you live and ask recovery disks command to your laptop

  The link to the assistance of HP WW is below:

  http://welcome.HP.com/country/us/en/wwcontact_us.html

  Paul

• Help with the MOUSE_OVER and MOUSE_OUT events

  Hello

  I am very new to Flash and I'm having a bit of a problem with my first ActionScript.

  I'm working on a project where I have a black and white photo. When you hover over the image, it turns to a color version of the same image. When you take your mouse out of the picture, it was in black and white.

  I have three instances of the image, a black and white image to frame 1, a color to frame 10 image and a black and white image to frame 20. Currently, when I mouse over the black and white photo, it turns to color image as I had hoped. However, when my mouse leaves the image, she remains on the color image.

  My code looks like this:

  import flash.events.MouseEvent;

  Stop();

  btnCory.addEventListener (MouseEvent.MOUSE_OVER, coryOn);
  btnCory2.addEventListener (MouseEvent.MOUSE_OUT, coryOff);
  function coryOn(event:MouseEvent):void {}
  gotoAndStop (10)
  }
  function coryOff(event:MouseEvent):void {}
  gotoAndStop (20)
  }

  btnCory is the first black and white photo in frame 1, btnCory2 is the frame of 10 color picture.

  Any comments / help would be much appreciated.

  
  Thank you

  
  Jeremy

  your movieclip with images on frame 1, 10 and 20 must have a name (for example, image_mc) and you do not need to convert images on 1 and 10 executives (and 20 if there is no point to have a duplicate on frames 1 and 20 image) to objects and your code should look like:

  import flash.events.MouseEvent;

  Stop();

  image_mc.addEventListener (MouseEvent.MOUSE_OVER, NFB);
  image_mc.addEventListener (MouseEvent.MOUSE_OUT, offF);
  function onF(event:MouseEvent):void {}
  image_mc.gotoAndStop (10)
  }
  function offF(event:MouseEvent):void {}
  image_mc.gotoAndStop (1);
  }

  and a message in the cc forum I see you are using 5 images, so use:

  import flash.events.MouseEvent;

  Stop();

  image_mc.addEventListener (MouseEvent.MOUSE_OVER, NFB);
  image_mc.addEventListener (MouseEvent.MOUSE_OUT, offF);
  function onF(event:MouseEvent):void {}
  MovieClip (e.currentTarget) .gotoAndStop (10)
  }
  function offF(event:MouseEvent):void {}
  MovieClip (e.currentTarget) .gotoAndStop (1);
  }

• Need help with the links and the fill color

  Hi all, I just recently discovered liveCycle and I am very impressed with it! I tried to get a calendar of working from home for awhile now and I did for the most part, but there are a few things more that I would like to add that I do not know how to do.

  I have experience HTML and Java, but very few XML or JavaScript experience. I have a feeling that what I try to do is relatively simple, but I just can't understand it! I spent hours on Google and the help files, and I feel that I got the end again, but not joy.

  I have attached my calendar (truncated to fit the size of max 5 MB attachments) so far. I would like it to do more than two things:

  1. have the background color of the table cells change from white to green when the checkbox is enabled.

  (Alternatively, I would really like to get rid of boxes to tick all the thogether and just the table cells background become green with a hotkey, such as "ctrl + D" to 'make'.) "But if this is not possible, then the color change with the box is fine).

  2. I want the button called "WORD DOC" in the upper right of the form to open a document in word on my local computer. I just push this button and a doc of work opens right in Word in another window.

  I was able to get. PDFs to open in the other two buttons here ('Big Java' and 'Beginning Java II') by adding the script

  app.openDoc ("Big Java.pdf");

  and

  app.openDoc ("Java beginning II.pdf");

  for each buttons respectively, but these PDF files must be in the same folder as the calendar to make it work. I tried just to edit this script by replacing the name of the PDF file by the name of a file to Word doc like this:

  app.openDoc ("test.docx");

  but the button does not work, there is simply nothing.

  So what I'm trying to do. I spent hours messing around with everything I could think of to make it work, but unfortunately I do not know the language well enough so he can work.

  I'd appreciate really any advice on this at all. I thank very you much for your review.

  Click on the second box to check and see the result.

  Is that what you want?

  Nith

• HP Pavilion a6000n - improvement of the system. Need help with the decision and suggestions

  Hi all

  I have a HP Pavilion a6000n, spec even with this link , except that I have 3 GB of memory and Window Vista Home Premium 32-bit.

  I think to update some of my computer hardwares that can run more smooth in some games and to improve my gaming experience.

  I'm looking to replace the processor and graphics card.  At the present time, I have an AMD Athlon (TM) 64 X 2 Dual Core Processor 4200 + 2.2 and a NVIDIA Geforce 6150SE nforce 430.

  My price range is around $100-$200 for processor and graphics together.

  I looked at cela processor and graphics card

  They will make a big difference and improvement than what I have at the moment?   If this isn't the case, then can you guys give me some suggestions on the choice of the better ones out there?

  Thank you!

  You have only a 300w ATX PSU (Power Supply Unit), then you will need to update if you plan to install a good graphics card.  Check the manufacturers minimum power required for the card you decide on getting.  As for the CPU, it does not require the upgrade - the graphics card is what causes your performance problems (in the games).  I would like to spend more money on a power supply and graphics card and leave the CPU alon (so far )

  Message edited by Kalt on 05/12/2008 23:18

• by comparing certain objects... helps with the formatting and variables

  I want to delete computer accounts in an ORGANIZATIONAL unit that do not exist in a folder of vmware...

  Step 1. Compare.

  $ad = Get-QADComputer -SearchRoot 'domain.lan/Test-NoGPO'
  $vmware= Get-VM -Location VDI_RemoteAccess
   
  Write-Host "AD" $ad
  Write-Host "VMWARE" $vmware
   
  Compare-Object  $ad $vmware
  
  

  Gives me this result:

  AD DOMAIN\DSTASA1$ DOMAIN\SXCH100$ DOMAIN\SKFB111$ DOMAIN\FAKEPC$
  VMWARE vstaq16 vstaq18
  
  InputObject                                                               SideIndicator                                                           
  -----------                                                               -------------                                                           
  vstaq16                                                                   =>                                                                      
  vstaq18                                                                   =>                                                                      
  DOMAIN\DSTASA1$                                                          <=                                                                      
  DOMAIN\SXCH100$                                                          <=                                                                      
  DOMAIN\SKFB111$                                                          <=                                                                      
  DOMAIN\FAKEPC$                                                           <=    
  
  

  I need the output of 2 first orders are the same... preferably just the 'name' of the pc. On the subject line - compare I tried to use $ad. Name and $vmware. Name but that the errors and says that it is null when the script runs...

  How to disinfect these lists and end up with a list of computers that are not in both places? (to later be deleted with other commands, not relevant here)

  You were there at halfway when you tried with the Name property.

  But you must keep all the computernames in 1 table and all VMnames in another table.

  Then, you can compare the 2 tables.

  Something like that

  $ad = Get-QADComputer -SearchRoot 'domain.lan/Test-NoGPO' | %{$_.Name}$vmware= Get-VM -Location VDI_RemoteAccess | %{$_.Name}
  
  Compare-Object $ad $vmware
  

• HP Pavilion Notebook - 15-p199: need help with the installation and activation of 10 Windows after completely uninstalling Windows

  Hello HP assistants.

  I need help for a specific problem. My laptop came with an installation of Windows 8.1. Then I upgraded to 10 Windows when it became available. After a while, I decided to uninstall Windows completely (to wipe the hard drive) and install a Linux operating system.

  Now, I decided that I want to use some software that is not available on Linux and if I want to reinstall Windows 10. My problem is that Windows has completely disappeared in a form any. So now, I need to download Windows 10 from an official source (which I think can be done fairly easily from the official source of Microsoft, although if there is a better, HP official medium to do this then please recommend it) and then I need to activate Windows some how.

  As has been made clear, I have the right to use Windows 8.1 and 10 but I would need to download Windows 10 and turn it on. Is there a way to do this? I'm literally stuck without solution.

  Thanks in advance.

  Hello

  As long as the previous installation of Windows 10 had activated Ok after upgrade from 8.1, you can simply perform a new installation as described in the guide on the following link.  Note: On the activation screen, select "I don't have a product key" - Windows will activate automatically once installation is complete.

  http://www.howtogeek.com/224342/how-to-clean-install-Windows-10/

  Kind regards

  DP - K

• Directly open an htm page to help with the TOC and header frame

  I was wondering if there was a way to directly load a specific help page and still have the images left and top display.

  For example, my main help page is:

  MyHelp\mainHelp.htm

  When I enter this url everything seems correct, and I have a TOC box with a senior that include search, etc.

  I also have a help page specific that I can navigate from the TOC framework.  Let's say that:
  Topic1.htm

  If I go MyHelp\Topic1.htm - the only thingdisplayed is the page of Topic1.htm itself and no other frames.

  Does anyone know how I can do these chassis more appear?

  Thank you

  See call WebHelp by using URLS on my site.

  See www.grainge.org for creating tips and RoboHelp

• Help with the lasso and auto smoothing...

  I must have done something by mistake - all of a sudden when I make a selection with my lasso tool, click on out of her, photoshop automatically smooths my selection (makes it smooth as in an oval or circle, ignoring my detailed selection).  How to remedy this situation, or disable auto-smoothing (?)?  Thanks for any help you can give.

  Set the value of the pen to a few or zero in the options bar.

  Paulo

• Need help with the query and output

  I have a table that contains a list of property and each an asset contains a category field, each an asset can have several categories assigned, then the category column is filled in a list (for example, 14, 16, 17, 19).
  
  The values are based on a table of categories using the primary key as a reference number (for example 14 = keyboards, 16 = Trackballs, etc..)
  
  I tried to understand how the power of categories so that when the category is displayed, the list will appear under the name of the category as opposed to the non referenced.
  
  example:
  < name cfquery = "qIndex" datasource = "#appDSN #" >
  SELECT Asset.Reference, Asset.AssetName, Asset.Category
  Assets
  WHERE category LIKE ' %#URL. Category #% '
  < / cfquery >
  
  < cfoutput query = "qIndex" >
  #Asset.Reference # < br / >
  #Asset.AssetName # < br / >
  #Asset.Category #.
  < / cfoutput >
  
  Exhibition:
  AD_987738
  Keyboard XYZ
  11, 14, 17, 18
  
  Table for categories are:
  CatID = primary key
  Category = category name
  CatImage = header Image
  
  Thanks for any help.

  Finally figured this out. Had to insert an intermediate query within the output to filter each record, otherwise he was out the results of the first record only and repeat.

  
  SELECT *.
  Assets
  WHERE category LIKE ' %#URL. Category #% '
  

  
  SELECT the CATEGORY, AssetID
  Assets
  WHERE assetID = #qIndex.AssetID #.
  

  
  Category category WHERE CatID IN (#catids #)
  
  
  Category: #qCat.Category #,
  
  #qIndex.Asset #.
  
  #qIndex.Reference #.
  
  

  Thanks again for the help.
  Paul

• Need help with the upgrade and activation 10 WIndows in Windows 7

  * Original title: upgrade windows 10

  I am now using windows 7 ultimate sp1, today get 10 app shows upgrade windows to windows 10 now.i am now in a little confusion if I update to windows 10 can he turn what method?
  right to digital or by using the product key.

  Is this the same computer - not necessarily the same problem or the Windows version - as in one or more of these other threads of yours?...

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/Windows-10-upgradation/6eec5c3e-4391-4a67-8a02-56bba437f137 (13 Mar-16)

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_10-performance/Windows-10-slow-running-showing-logo-twice-when/a3b1bea1-8871-43f9-840B-efa46445a557 (Mar 04 - 16).

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_10-performance/Windows-10-Pro-blue-screen/4991e1a1-c54d-4B35-b28e-9ccfedec3359 (29 February-16)

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_10-update/how-to-get-November-update/390e4cec-d39b-4D6F-B03D-1d6ed069e25f (20 Feb-16)

• HP 15 laptop: problem with the touchpad and the key "stuck."

  Hello!
   
  Last weekend, I have an irritating problem with my HP 15 laptop. Bought two years ago and upgrades to Windows 10 a year ago.
   
  First of all, my touchpad started to not work properly. It "freezes" and I can't use it until I click the ESC key, but it doesn't last and "freezes" again a few seconds later. Then, everytime I open a window where there is a text box (Start menu, edge browser, Control Panel, etc.), the number 5 is entered automatically and permanently, as if the button 5 has been blocked. I did a quick check and button 5 do not seem physically stuck.
   
  Yesterday, I restored the system to the factory settings, so I'm back to 8.1 for Windows and then upgraded to Windows 10. Everything seems to work fine, but this morning, the problem was back. Is there something I can do? What is the problem caused by Windows 10 or the computer? Should I restore it to Windows 8.1? Everything worked great til last weekend, I don't know what that was.
   
  Thank you in advance for your help!

  Welcome to the HP support community @gouch3.

  I understand that you have a problem with the keyboard and the touchpad on your laptop from HP 15.

  Have you tried to use a keyboard external and mouse at all?

  Have you tried to go to Safe Mode to see if the problems persist in there?

  Have you tried to perform a material or forced reset Reset?

  Did you do a test of material?

  Have you updated your drivers?

  gouch3 wrote:

  ... Is there something I can do? What is the problem caused by Windows 10 or the computer? Should I restore it to Windows 8.1? Everything worked great til last weekend, I don't know what that was.

  It could be a driver problem to be able to look at that for you, I need your model number. I wish I could give you an answer or not, but at this point without the troubleshooting results and the model number, it is difficult for me to say.

  I can say that if everything works in point 8.1 of Windows without problem, the driver TROUBLESHOOTING is a great place to start. Please try to follow these steps for the keyboard and the touchpad of troubleshooting:

  • Beginning
  • Search for Device Manager
  • Search results, open Device Manager.
  • Click on display
  • Show hidden devices.
  • Click the arrow next to keyboards.
  • Right click on the name of the keyboard device.
  • Select uninstall.
  • Continue deleting the names of devices in the category keyboards until the feature of all the names have been uninstalled.
  • Restart the laptop twice.

  Touchpad:

  • Type of research, "Device Manager."
  • Click on Device Manager,
  • Expand mice and other pointing devices.
  • Right click on the TouchPad,
  • Click on uninstall.
  • Restart the computer laptop twice,
  • Reinstall the TouchPad card.

  I found a document of troubleshooting for you to try also called Portable keyboard troubleshooting. Please be sure to follow the steps described in this document.

  The best document I have for TouchPad problems is the use and troubleshooting of the TouchPad and ClickPad document. 

  Here is a link to the HP Support Assistant, if you need it. Just download and run the application and it will help with the software and drivers that need to put up-to-date.

  This is a great question other clients may also be questioned. When we came to a resolution, please share what has worked for you with others by marking this post as an acceptable Solution. If you want to show appreciation for my efforts today, please take a second to click the Thumbs Up button below.

  If you need assistance, I would be more than happy to continue to help you. Please re-post with the results of the resolution of the problems. Could you please also provide your model number (How can I find my model number or product number?)

  Thank you!