How default context in plsu security edition asa 5510

Similar Questions

• Cisco ASA 5510 - restrictions of VPN (AnyConnect) based on the AD user or IP address

  Hello

  I want to test how to restrict access user on an ASA 5510 AnyConnect. In politics, I can define what networks will go through the VPN tunnel and which not (split tunneling). The ASA has a LDAP connection and only AD users with a special security group can connect over AnyConnect.
  On the other hand I would like to restrict access for special users within a VPN policy.

  So my question:
  What are your recommendations to implement this szenario?

  My two ideas would be:
  1. the access rules based on the user of the AD.
  2. special reserve IP addresses in the pool of addresses AnyConnect for some users, so I can limit access to the normal firewall rules base based on the source IP address.

  What are your recommendations and is it possible to realize my ideas (and how)?

  Thanks in advance

  Best regards

  Hello

  I will suggest that you configure a second ad group in the server and another group strategy in the ASA, you can configure certain access on each group policy "the installer of the filters, assign different split political tunnel, different ACL' and in the ad server, you can assign users for example to the AD Group A and AD Group B based on the access you want to give them now , you must configure LDAP mapping to assign the user specific group policy that you want based on the AD group that they belong.

  You can follow this documentation that will help you configure the LDAP Mapping:

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  Best regards, please rate.

• ASA 5510 w / license more lost security contexts

  I have an ASA 5510 with license more than security and when I looked the devices a few days ago, I had 2 contexts, however after you have configured the port of Mgm as a regular port contexts show 0, why?  I can't find anywhere on the internet where this problem occurred: this is the result of show worm:

  Cisco Adaptive Security Appliance Software Version 7.0 (8)

  Updated Sunday, 31 May 08 23:48 by manufacturers

  System image file is "disk0: / asa708 - k8.bin.

  The configuration file to the startup was "startup-config '.

  SHIELDASA01 up to 21 hours 16 minutes

  Material: ASA5510, 256 MB of RAM, processor Pentium 4 Celeron 1600 MHz

  Internal ATA Compact Flash, 256 MB

  BIOS Flash M50FW080 @ 0xffe00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)

  Start firmware: CNlite-MC-Boot-Cisco - 1.2

  SSL/IKE firmware: CNlite-MC-IPSEC-Admin - 3.03

  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05

  0: Ext: Ethernet0/0: the address is 0021.a025.2d3c, irq 9

  1: Ext: Ethernet0/1: the address is 0021.a025.2d3d, irq 9

  2: Ext: Ethernet0/2: the address is 0021.a025.2d3e, irq 9

  3: Ext: Ethernet0/3: the address is 0021.a025.2d3f, irq 9

  4: Ext: Management0/0: the address is 0021.a025.2d3b, irq 11

  5: Int: not used: irq 11

  6: Int: not used: irq 5

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 25

  Internal hosts: unlimited

  Failover: Active / standby

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 0

  GTP/GPRS: disabled

  VPN peers: 150

  This platform includes an ASA 5510 Security Plus license.

  I'm not showing the serial number and keys licese for obivious reasons.  Any help? Thanks in advance.

  You might want to try upgrading your IOS on the SAA, see if it can help, can you check the firewall mode (single or multiple) you're currently on? is your asa transparant or routed?

• How many interfaces in asa 5510

  can someone pls tell me how many interfaces in asa 5510.and we can add more interfaces to it.

  concerning

  Assane

  Hi assane,.

  When you order the ASA5510, you can choose between (option Setup/Noo-Noo fixed to add more ports interface):

  1 ASA5510 device comes with 3 x FastEthernet, more 1xmanagement port (FastEthernet)

  ASA5510-BUN-K9: Cisco ASA 5510 Firewall Edition includes 3 Fast Ethernet interfaces, 250 peers IPSec VPN, SSL VPN 2 peers 3DES/AES license, or

  2 ASA5510 comes with 5xFastEthernet, most 1xmanagement port (FastEthernet).

  Cisco ASA 5510 Security Plus Firewall Edition includes 5 interfaces Fast Ethernet, 250 VPN IPSec peers, 2 peers of SSL VPN, high availability active / standby, 3DES/AES license

  http://www.Cisco.com/en/us/products/ps6120/products_data_sheet0900aecd802930c5.html

  Rgds,

  AK

• How can I provide internet security for my 10.7.5 unsupported macbook?

  How can I provide internet security for my 10.7.5 no support for operating system Macbook?

  The best way is just to use your common sense and do not download third-party applications, don't use torrents. Except that you can install AdBlock for stop pop ups. If you happen to get malware, download and run MalwareBytes. Malwarebytes was developed by one of our colleagues here to ASC. He received rave reviews and is on the more proven anti-malware for Mac software.

  EDIT: Do not use any type of security application Internet only these will create more problems than they solve.

• How can I get a security code on my wifi neighbors are tapping into my use

  the neighbors are tappin celine my wifi how can I put the security on my computer setting to stop it.

  \

  Hi Becc,

  Essentially, the procedure is to configure the router for the specific appropriate for your router, and your ISP and your computers and intranet security settings.  You do not block your computers, you encode router transmissions so that others cannot use it without the username and password.  Then you configure your computers (or other devices connected) so that they know the appropriate codes and can communicate with the router.

  When I came across this myself, I discovered that the manufacturer of the router charged; However, I discovered that my ISP supports this particular router and they helped me as well with the router and my computer for free as part of their service - so I'd personally start with your ISP to see if they will help you.

  The following article gives the basic instructions for the router (and a few different), but it only covers the router (and not your connected devices) and it indicates the options to use but sometimes 'the best' is not appropriate or accessible with your ISP or router and the computers (which means that it's OK to learn about it in a general sense (, but you need to communicate with people to get the correct settings).  For example I would use WPA2 but my ISP doesn't support WPA is what I use (and if I tried the other it wouldn't work and I would have had no. clue what I was doing wrong and be stuck and confused). http://www.ehow.com/how_6942409_set-up-wireless-router-security.html.  So think of this as simply a presentation guide but use the following instead.

  In short, to access the router, go to any computer connected and click on start / all programs / accessories / right-click on command prompt, and then click Run as administrator.  Then type IPCONFIG/all.  For your first login, you should see a group of settings as a gateway by default (and possible other inputs) referring to a TCP/IP address (usually 192.168.0.1 or something similar to that).  This is the address of your router.

  Open now IE (or your browser) and in the address field where you can type www.microsoft.com, sometimes rather type the address of the router (for example, 192.168.0.1) and enter.  This should connect to the router where it will ask for a user name and password (almost certainly).  If you know, very well.  If this is not the case, the access provider manufacturer or router can help.  Many use default common (which you should change once get you it, but remember).  Certain combinations of username/password common name include admin/admin, admin/password, administrator/administrator/admin password, simply administrator or with any other admin for the password.

  There must be a security section.  Need you probably to get a security Type (WPA-Personal, WPA2-Personal,...), a Type of encryption (for example, TKIP, AES,...) and a security network (password thinking) key.  The first two depend too much from your ISP and the installation program to help me (and you may have different options or more also)-they need to tell you what to use.  The manufacturer of the router can probably help with this - but the ISP knows and can tell you.  Use a key strong you want it is hard to break.  Here is an article on the creation of strong passwords - for this and especially since you know that you used, I would out max and go even a little further than they suggest: http://www.microsoft.com/security/online-privacy/passwords-create.aspx.  I would choose one with 12 numbers which is a random set of letters lowercase, uppercase, numbers, and symbols - but also one you won't forget but that is anyone's guess (that you don't really want to not have to reset it).

  Once set, so even if not recommended by the router or the people of the ISP because if you forgot your password again, they will not be able to help the router becomes a paperweight (but it prevents a person to reset the router using the same stuff, I suggested above to find one that works - if they were not working and you don't need help to identify it) I would consider changing the default user name and password reset so no one can use this method ignores everything and get (even if you notice that and eventually be locked out yourself - and quite well, they will have to have physical access to the router to reset it because I don't think that this can be done remotely).  I did it with mine.  Others choose not to bother because they assume that nobody's going to such extremes and it would make things easier if you needed help more later and I forgot the password.  It's your choice.  I did it because I'm a little paranoid and know that I forget - but for the most part, I suggest they leave alone that can be a bit going overboard.

  Then go to all devices connected wireless or another for the router and configuration, security codes to enable this device (your computers and perhaps a printer or other devices) to access the router and don't not blocked everything as your neighbors now will be.  Go to network connections and sharing, then the list of wireless connections and select the connection of your router and right click and click Properties.  Click Security and three above options should appear.  Change them to match what you used for the router and save the settings.  Now close the connection to the router (if it doesn't what shouldn't be) and re-establish a connection and you may in.  Do same for all devices (printers and other devices probably have special methods to change these settings and you may need help with these providers to find a way to review the security settings to connect to the router - but usually it's really not hard and you can probably work yourself or using self-help on the Web site of the device or the manual if you still have it).

  That's all.  You have now completed and you are sure.  Again, you will need help from the ISP with the parameters (and they can also help you with everything if you ask and you need), but with this exception, most of the time I think that you can usually do it on your own.  Go into the router manufacturer only if absolutely necessary and the ISP will not or can not help and you can't find try it yourself since many of them charge for this kind of thing (unless it is brand new and some even then) and you need information from the ISP in any case as the router manufacturer probably does not know the right settings for each provider (even if they do for many is not reasonable to assume that they know not just less likely to the ISP).

  I hope this helps.  Assuming that this has not already been moved on Windows Networking Forum, and if that didn't do the trick and you need more assistance, please repost it here: http://answers.microsoft.com/en-us/windows/forum/windows_other-networking?page=1&tab=all&tm=1300700638376.

  Good luck!

• How can I get Microsoft Security Essentials antivirus security?

  After another year of Norton 360, I got the stupid games of Symantec, tired of the ot, uninstalled and downloaded Microsoft Security Essentials.  I restarted my computer (Dell Dimension 8200 running Windows XP Pro 2002).  After that, I ran services.msc impatiently as my program of service to show that my antivirus security worked and I had nothing to fear.  Imgine my grief when my service center reported that my computer was always subject to viruses, worms, Trojan horses and other forms of malware.  I thought, perhaps, I had reduced the activity of some vital download too quickly and, therefore, have prevented a good download.  So I tried again, this time with a lot more patience...   This time, I received a message that the program was already on my computer, asking if I wanted to replace it with the new download.  Because the first time I acted in a hurry, I replied that I tried the second download try replacing the Lerna, this time with a lot more patience.  There is no apparent change that showed the Security Center: no protection against the virus.  How can I get Microsoft Security Essentials to act as my antivirus program and my Security Center to recognize it as such?

  Hi David,

  Glad to hear thiings are better. Do not forget to chek that MSE will automatically update the definitions that every 24-48 hours and regular tests are carried out. Also suggest that you go to settings > default Actions and change to quarantine all. don't forget to 'Save changes'. This is recommended to avoid problems such as potentially unwanted programs and the removal of the odd false positive.

  You are definitely not alone in your skepticism about Norton and other paid for antimalware solutions.

  Feel free to mark my initial response as response and/or useful.

  Have a day without malware.

  Kind regards

  rhabdomantist

  _______________________________________________________________________________

  For more information on how to protect you and your computer, I refer you to the following:

  Safety & Security Center
  http://www.Microsoft.com/security/default.aspx

  Virus and Security Center
  http://support.Microsoft.com/contactus/cu_sc_virsec_master?ws=support#TAB0

  Malware Protection Center
  http://www.Microsoft.com/security/portal/default.aspx

• How to upgrade an ASA 5510/20

  I have several ASA 5510 and 5520 requiring an update and I tried to find a way to automate the process. Many of the features are running in active/active mode (primary is active and the secondary is in standby mode).

  I'm looking through the ADSM features and I found the automatic update. This looks like a good way to go because he downloaded the software for primary school and then transfers her back to the secondary device. It then performs the update device 1 both starting with the secondary device. But he said: I need a server was updated to contain the new software and I do not know how to create a. I have a machine that a FileZilla server is installed, but that uses FTP and the Automatic Updates settings are looking for an HTTPS address.

  The other option I havea Cisco first Infrastructure 2.0 is available. I can use this to manage the software, but there is nothing on how to use it with an ASA installation as an HA pair.

  I could use any help you may have.

  Cisco Security Manager is more generally used as a server update for large deployments ASA.

  PI 2.0 is a little rough around the edges on its support of ASA, and I would judge not quite ready for this task. (It is same with the package update of December 2013, which increase the support of the ASA).

  Depending on your version, most people are not comfortable with auto update of firewalls. Things have changed considerably with post-8, 2 and all migrations I've ever done that (TENs) involves a manual check of the new syntax and operations.

• Everytime I open a doc it opens to 148%. How default opening zoom to 100?

  Everytime I open a doc it opens to 148%. How default opening zoom to 100?

  Thank you

  Hi dumitruv51327095 ,

  Please try browsing in Edition > Preferences > select 'View Page' in the categories and set the zoom level to 100% under the label "Default layout and zoom. Click OK.

  

  Let us know if that helps.

  Concerning

  Sarojini

• How to grant access to secure with sending a 1 2 areas form

  How to grant access to secure with sending a 1 2 areas form? For any help or suggestion would be appreciated.

  If you change the zone-1 ID in the form action, it will return to the page and a default logon you connected. You have access to all areas will be saved in. Technically, you can connect even with no associate also area long have you a username and password.

• How to do in the security settings

  Can how I get in the security settings of safari

  Depends on what you mean. Security preferences are located in the preferences panel security & privacy of system preferences. For Safari, open Safari preferences and click on the Security tab.

• I have not added rescue e-mail and I forgot my security question. How can I reset my security question

  I have not added rescue e-mail and I forgot my security question. How can I reset my security question

  I am also having same problem here in the Maldives, even we cannot contact apple Help Center. Someone please let us know how we can overcome this problem as soon as possible. I am not able to buy now. I created my user 5/7 years back.

• How do I change the security questions?

  How do I change the security questions?

  Hello

  If you set an alternate e-mail address, you can reset your security questions. Follow the instructions here to check if this option is available:

  • If you forgot the answers to your questions of security of Apple ID - Apple Support

  Otherwise, you will need to contact the Apple Support. The information is available here:

  • Contact Apple for assistance with the security of the Apple ID - Apple Support accounts

  (I'm afraid that no one here can solve the problem for you.) You don't talk to Apple here - it is a community based on the user).

• How to install the avg security toolbar in Firefox?

  Hello

  I installed IE10 on my new desktop (HP W7 Ultimate 32 and 64 bit), downloaded AVG free and selected the option to include the AVG Security Toolbar - everything has been installed. I then downloaded Firefox 22.0 but found no option to install the AVG security toolbar. How to install the AVG security toolbar into my existing Firefox browser? Thank you. jav1, 10/07/2013

  To enable secure in firefox, read the security settings. I don't have a number for AVG, but try to use their support for http://www.avg.com/us-en/support

• How can I change the security answer?

  How can I change the security answer?

  If you forgot your Apple ID security questions answered - https://support.apple.com/kb/HT201485

  Frequently asked questions about Apple ID - http://support.apple.com/kb/HE37 -> Can I change the answers to security questions of my Apple ID?  -> Yes. You can change responses to security issues that are provided when you initially enroll in your Apple ID go to my Apple (http://appleid.apple.com/) ID and click on manage your account.

  Advice to the user to alarm: some Solutions for forgot security reset issues - https://discussions.apple.com/docs/DOC-4551

  KingPenguin 02/2015 post - https://discussions.apple.com/message/27660375#27660375

  Rescue email address and how to reset Apple ID security issues - http://support.apple.com/kb/ht5312 - "If you don't remember your Apple ID security and answers questions, email backup option provides a way to reset the.» In addition, all future emails related to safety of your Apple ID will send to the email address of relief. »

  January 2014 post about to contact Apple to reset security - https://discussions.apple.com/message/24543247#24543247 and https://discussions.apple.com/message/24671039#24671039 and other related expenses issues, February 2016 - https://discussions.apple.com/message/29465949#29465949

  If none of the above works, contact the support of iTunes at http://www.apple.com/emea/support/itunes/contact/ and follow the instructions to report the problem to the iTunes Store.