ASA 5510 w / license more lost security contexts

Similar Questions

• License problem of security context for Cisco ASA 5585

  Hello

  Can someone help me in license number for the ASA 5585 security environment,

  We recently purchased a box ASA (5585) which has 2 default security context and we had like to have context for this ASA 25 permit and we got two codes PAK of Cisco for 20 licenses and 5 respectively.

  When we generate the license key by combining the two codes Portal Cisco PAK and apply the same on ASA, do not see the 25; Instead, it shows only 20.

  Is it really possible to stack context like 20 + 5 licenses or to buy a PAK code for any license 25 context?

  Please advise me on this.

  Thanks in advance!

  Kind regards

  Kam

  Hello

  This should probably not be handled with Cisco directly or through the company that got you the license.

  To my knowledge, there is a possibility that the you have everything first to install a license key and the other licence could be upgraded from the previous license until the following limit of function under license.

  I had several occasions where I was provided with the wrong license and had to communicate with Cisco/provider to get licenses appropriate for my device.

  While I was announcing this response I checked the document of licensing for ASA models. It seems to me that there is no security content license 25 for the SAA. The deadline is 20 and license of SC 50 SC

  Check this document:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/intro_license.html#wp1230400

  -Jouni

• ASA 5510 Anyconnect licenses with Cisco Anyconnect VPN IP phone

  Hi, hoping someone can shed some light on what I'm just more confused over trying to get by. Not sure if this goes in the section IP Telehpony or here...

  We have an ASA 5510 with the base license. We need to install IP phones to home teleworkers, and I understand there are Cisco IP phones that have built-in VPN clients to enable a tunnel to the central private network. IT seems that you can't use Anyconnect VPN to do this, and I am trying to establish what upgrade licenses, we must apply to the ASA, as both Anyconnect licenses that you get for free on the SAA is not enough.

  This is the phone that we seek;

  http://www.Cisco.com/en/us/prod/collateral/voicesw/ps6788/phones/ps10499/ps11005/data_sheet_c78-603725.html

  I want to know is the Anyconnect Essentials license will work with these IP phones?

  When I do a version of the show,

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 50

  Internal hosts: unlimited

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 0

  GTP/GPRS: disabled

  SSL VPN peers: 2

  The VPN peers total: 250

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect for Linksys phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes a basic license.

  It shows "AnyConnect for Linksys phone: Disabled", it is the same for the Cisco IP phones? It is the kind of specific license, should I seek for Anyconnect on IP phones or will Essentials?

  Hi Leo,

  you will need 2 licenses: an Anyconnect Premium license and a permit «Anyconnect of Cisco VPN phone»

  ASA 8.2 and earlier license "for Cisco VPN Phone" has been named "for phone Linksys' it's the same.

  CFR. http://www.Cisco.com/en/us/docs/security/ASA/asa84/license/license_management/license.html#wp1487574

  HTH

  Herbert

• VPN Cisco ASA 5510 - 250 licenses?

  I can't find a clear answer on this.  I see that only 2 SSL VPN clients are included, but if I buy an ASA 5510 (ASA5510-BUN-K9), am I allowed to use as a VPN endpoint for up to 250 customers?  If so, is it a total of VPN 'site-to-site' and 'customer '?

  For IPSec VPN (IPSec VPN site-to-site and remote client access), there is no additional license required as it is included in the device.

  For SSL VPN, there is failure to license 2, and if you need more than 2 connections SSL VPN Client, then Yes, you must purchase an additional license (the AnyConnect Essentials or the AnyConnect license Premium depending on what you need).

• Cisco ASA 5510 + license + AIP - SSM

  Hello.

  I have this box.

  I have a few questions about it.

  (1) I'll be able to update the firmware (from 8.2 to 8.3 or greater for example) without smarnet for ASA 5510? And what can not do without smartnet?

  (2) I have only AIP-SSM-10 module this ASA 5510. is there a smartnet, too? And when I buy only one module is it build in a subscription for 1 year for the signatures of the IPS?

  (3) if I have the Cisco ASA 5510 base license, my IPS on AIP-SSM-10 will work?

  (4) as I foresee in a purchase of the year a 5510 more with the same module and mount ther of failover. I really need license Security more than failover (active / standby)? For active/active, I know I need one, Yes?

  Please help me.

  (1) you must Smartnet in order to download the software from the download from cisco.com site.

  (2) Yes, there is also a smartnet for the AIP module. Module AIP does not come with one year subscription, but you can ask for a demo license.

  (3) Yes, the basic license is OK for the AIP module.

  (4) Yes, you would need license security more on the two ASA to be able to run any type of failover on ASA5510.

  Hope that answers your questions.

• How default context in plsu security edition asa 5510

  Hi could someon pls tell me with the edition of security plsu asa 5510 it will support active/active failover. and she supports context with securiyt plsu edition. and how default context do we receive with edition of plsu security asa 5510.

  concerning

  Assane

  Hello

  By default, ASA5510 with Security Plus comes with default 2 security [email protected] / * / firewall. Context of maximum security, you can have (upgrade to) is 5.

  With license upgrade of security Plus, you might have active/active and active / standby (choose one to run at any time) high availability services.

  http://www.Cisco.com/en/us/products/ps6120/products_data_sheet0900aecd802930c5.html

  Rgds,

  AK

• AnyConnect VPN license on ASA 5510

  Hello

  We have ASA 5510 IPS with basic license. We must now Anyconnect support for more than 2 users.

  Anyconnect (tunnel mode) but essentially Anyconnect license enough? Do need me a license for SSL VPN peers?

  What about Anyconnect without customer, I see that I need a premium license?

  This one is pretty ASA5510-SSL50-K9? It's really expensive compared the Anyconnect Essentials.

  Here is my worm out sh:

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 50
  Internal hosts: unlimited
  Failover: disabled
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 0
  GTP/GPRS: disabled
  SSL VPN peers: 2
  The VPN peers total: 250
  Sharing license: disabled
  AnyConnect for Mobile: disabled
  AnyConnect Cisco VPN phone: disabled
  AnyConnect Essentials: disabled
  Assessment of Advanced endpoint: disabled
  Proxy sessions for the UC phone: 2
  Total number of Sessions of Proxy UC: 2
  Botnet traffic filter: disabled

  This platform includes a basic license.

  Yes, AnyConnect Premium includes all the SSL features (including the complete tunnel mode AnyConnect - which is what sustains essential AnyConnect).

  So if you buy the 50 user for AnyConnect Premium license, you can have up to 50 SSL VPN connections, if they are the combination of all without customer, or combination of tunnel without customer and full, or just full tunnel. All with a maximum of 50 simultaneous SSL tunnels.

• ASA fire services and security context

  Hello.

  We have an old asa 5510, and we would like to change with a new x 5525 asa with services of firepower, using the fueatures IPS.

  In the firewall of the production, we organize 6 security contexts; so the question is: If buy us this product, we can use IPS FirePower feauters in any security context or do we not have limits?

  Thank you

  Daniele

  The only restriction is that one set of politics of power must be applied for all contexts will share policy.

• All necessary licenses on ASA 5510 for old Cisco VPN Client

  We're trying to migrate our firewall Watchguard to a Cisco ASA 5510, who bought some time ago. For some reason, all of our users have already installed the old Cisco VPN client. I think it will work. Are there licensing issues on the 5510 I had to be concerned with?  No matter what special config that needs to be done on the 5510?

  Fix. You don't require licensing of AnyConnect of any type of configuration and the use of IKEv1 IPsec remote access VPN (which use the old Cisco VPN client).

  You will be limited to 250 active IPsec peers (remote access more no matter what VPN site-to-site) by the platform (hardware) device capabilities that are enforced by the software.

• ASA 5510 licenses

  Hello experts!

  I'm looking forward for more information on licenses active / standby and according to this link http://www.cisco.com/en/US/partner/products/ps6120/prod_models_comparison.html I need to consider the licence security more, BUT according to this link: http://www.cisco.com/en/US/docs/security/asa/asa82/configuration/guide/ha_active_standby.html#wp1046838

  indicates that the Base license is necessary to achieve a/s HA configuration on ASA 8.2.

  The current version of the ASA: 8.0.

  I have to go to 8.2 (x) in order to activate the c/o HA configuration or is required to buy this security license more?

  Thanks in advance for your help!

  If you upgrade to 8.2 (x), you can run c/o HA without security over the license.

  If you stay with 8.0 (x), you must have Security Plus.

  With a 5505, you must always have Security Plus to c/o HA.

  Please rate if this helps.

  Thank you

  Tim

• Cisco Anyconnect/WebVPN license for ASA 5510

  Hello

  Someone could please check the licenses for ASA 5510 attachment and let me know. We currently have ASA 5510 with basic license. According to the table attached under VPN sessions, he mentions that "250 combined SESSIONS IPSec and WebVPN" and to "Max box of WebVPN Session" it is mentioned that 2nd meeting, exceeding that we must buy license optional webvpn. While we the 250 combined license for IPSec and webVPN. We must purchase additional anyconnect license to set up remote access for users who want to use the internal resources from outside the network. OrElse, we don't have to purchase license and can configure webvpn/anyconnect of existing combined license existing users basic ASA license? Waiting for your response. Thank you.

  You are welcome.

  1 Yes

  2 AnyConnect requires no Java, but it can he use when connecting to one AnyConnect SSL VPN client and launch the Web browser option start Java-based. There was a bug with the AnyConnect old versions had later who should have addresses. You also have the option to launch via IE and using ActiveX or simply throw AnyConnect directly - neither of these two methods require Java.

  Here is a document TAC on the Java questions if you want more details.

  Please take a moment to note the useful messages and mark your answers questions.

• ASA 5510 - level security Interface

  I have an ASA 5510 (8.2.1 code). I'll implement the separat IPSec tunnels two remote networks, but each remote connection to an ASA respective interface.

  Question: I know that the e0/0 ('outside') security level of the interface is 0. However, only the second interface e0/2 ("out2") security level must be set to 0 as well?

  Thank you

  Jim

  Yes you can, simply apply the respective crypto map to the interface. You might want to do e0/2 and e0/3 the same level of security (if your security policy allows) and same-security-traffic permit inter-interface. Which allows communication between the various interfaces that have the same level of security. You can ignore the NAT mess.

• Licenses, IPS on pair of Cisco ASA 5510 active / standby

  I have two ASA 5510 devices in Active mode / standby.  I think of buying both used IPS modules and their installation.  My question is, me 1 or 2 licenses IPS that requires?  We are on 8.4 right now, and I see 8.3 Cisco changed license to c/o to where you need only one license, not two.  This is true for any way VPN licenses, so I was wondering if the same applies to licenses IPS.

  In addition, the unique licensing model will as much as only requiring a base for the pair a/s license too?  Or is the base license, something that you must have two pair a/s?

  Failover doesn't f, you have only one module in the ASA elementary school. You must have two modules. But it is fine if you do not have a subscription license for your secondary IPS (at least for the system).

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• ASA 5510 more and Port forwarding

  Hallo,

  I don't know if the thread title is correctly written, so I'll try to explain my problem.

  I have an ASA 5510 more linking several external interface VPN tunnels to internal interface. they work very well. Now I want to access a server in the internal network of trust on the Internet via RDP.

  I've set up a static NAT rule which translates by [my public ip phone]: 11111 on [the internal server ip]: 3389. Moreover, I met [my public ip phone] traffic: 11111 outside [the internal server ip]: 3389 inside via the access control list.

  Yes, it does not. I made a few soft logic error?

  Code:

  static (exterior, Interior) [the internal server ip] tcp 3389 [my laptop public ip] 11111 netmask 255.255.255.255

  Outside_access_in list extended access permit tcp host [my ip public notebook] [internal server ip] eq 3389

  Best regards

  EYAD Tayeb.

  Hi... I might have a word here!

  looking at your config you have

  static (inside, outside) tcp 3389 11111 netmask 255.255.255.255

  It should be

  static (inside, outside) of the tcp 3389 3389 netmask 255.255.255.255 interface

  Also... Make sure that the aplpied of the access list for the external interface in the outbound direction does not block traffic referred by your inside host with the public client that initiated the RDP session.

  I hope this helps... Please, write it down if she does!

• ASA 5510, get the right pair

  Hi, I have a 5510 with security more on 7.2 (3) and I'm looking to pick up a 2nd economic unit on eBay to set up like a pair of HA a/s. Of course, there is a little supply, and one I am looking at matches closely enough. My question to the Board of Directors is how special is licensing when it comes to match? Both are Security Plus, and I don't understand why the discrepancies in Max VLAN, security contexts, and a few other parameters.

  My reading abt licensing indicates different levels of security over for example Max VLAN is just indicated that 100. I think it's because the #2 is on 7.0 (3). Maybe some of these features have increased in later versions? But I have no way to control until I have buy TI -.

  The plan will be to upgrade all two to 8.2 and bump mine to 1 GB to match... I wanted to just make sure that I wouldn't be in a situation where they would not match for some reason any. Thanks in advance

  Mine

  Material: ASA5510, 256 MB of RAM, processor Pentium 4 Celeron 1600 MHz

  Internal ATA Compact Flash, 256 MB

  BIOS Flash M50FW080 @ 0xffe00000, 1024 KB

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 100

  Internal hosts: unlimited

  Failover: Active/active

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 2

  GTP/GPRS: disabled

  VPN peers: 250

  WebVPN peers: 2

  This platform includes an ASA 5510 Security Plus license.

  Project #2

  Material: ASA5510, 1024 MB RAM, Pentium 4 Celeron 1600 MHz processor
  Internal ATA Compact Flash, 256 MB
  BIOS Flash Firmware Hub @ 0xffe00000, 1024 KB

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 25
  Internal hosts: unlimited
  Failover: Active / standby
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 0
  GTP/GPRS: disabled
  VPN peers: 150

  This platform includes an ASA 5510 Security Plus license.

  Hello

  Indeed, there are some differences that you need to fix in order to be able to have a failover pair, BUT as you increase her memory... Why don't you go to 8.3 as the restriction of licenses will disappear for failover purposes,

  the units will now share it instead to compare

  concerning