How do I create a network map in network and sharing Windows 8 Center?

Similar Questions

• Network and sharing - Windows 7 - Center does not

  Hello

  I just bought a new laptop Packard Bell with windows 7 (64-bit) and it is not connect to networks. To resolve this problem, I decided to try to do it manually by going to the "network and sharing Center." The loading icon but then control panel display just hangs. If I let it charge all just never stops loading. He becomes insensitive and ultimately I have to use the Task Manager to close.       Any ideas?

  Thank you

  Josh

  Hello JoshBoi,

  Thanks for posting in the Microsoft Answers forum! Try to start your Windows 7 computer toSafeMode w / Networking to see if the slow speeds still occur. There may be third-party software that are causing your problem. If the problem persists, try to perform aclean boot to see if that fixes the problem. If you please, after back and let me know the results.

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• How can I create a network and put in on my iphone 4S for use with wifi?

  I have a phone, a personal hot spot 4s, a router and a broadband cable. Everything is running but I can't figure out how to get my network on my iPhone for use with Wifi.  Also, I don't know how or where on the phone to set the password and since I don't have a different password, I can't use my wifi?  Help, please!  My iPhone tech is exhausted and I'm going against a brick wall with my internet service who refuses to provide me with their ISP, etc.

  Hello

  Please ask your question the following support forums.

  iPhone: Apple Support communities:
  https://discussions.Apple.com/community/iPhone?CategoryID=201

  Concerning

• Network and sharing residential group Center

  Bad for a some time now thanks to the homegroup in Win 7 PC. I have two PCs I want to do the networking. Both are running Windows 7.

  I want to set up the homegroup on MainPC and have LapPC to join the homegroup.

  It won't work. Tried several times.

  I can set up a homegroup on MainPC but I don't get the opportunity to join of LapPC.

  I can implement the homegroup on LapPC and I MainPC join, but I'm not all MainPC.

  I went through the steps to leave the homegroup on both PC again... several times.

  Don't send not just me a link on how to put in place a homegroup. I did it over and over again.

  I need someone to help me with this problem seriously. It worked until about 2 months ago!

  Hello

  Then your router sends IPv6 properly and should work as it did. Use the other methods
  to check the issue. Do not have an update of the firmware on your router.

  Were you doing the hard reset as suggested?

  Rob - SpiritX

• "Library not registered" in Vista Home Premium in network and sharing Center trying to activate the password protected sharing.

  Trying to activate sharing protected by password in the network and sharing window I get the error message "library not registered. Also, in media player, I get always an error of sharing multimedia. I think that the 2 mmight be bound. PLEASE HELP ME!

  Hi Dj,

  When he the accur first question?

  Have you tried a system restore to a point before the question accurred?

  You can follow the procedure as described below:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: follow steps 7 to place the computer in his usual when you finished the clean boot troubleshooting

  Do the system restore to a date preceding the accurred question according to the link below:
  System restore
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

  Reply back with more information for you to help

  Kind regards

  Kiki

• When I create an ad hoc network on my laptop HP using Win7, I find in the 'manage wireless networks' (in the network and sharing Center)

  Hello, when I create an ad hoc network on my laptop HP using Win7,

  I can't find it in the 'manage wireless networks' (in the network and sharing Center)
  can you help me please?

  Hello

  In case there are problems with your computer or it network devices check
  with HP, their documentation online support and drivers, diagnostics, and
  Ask problems known in their forums.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ==========================================

  The routers are much easier and they don't cost much.

  These should help:

  References to Vista also apply to Windows 7.

  Set up a computer-to-computer (ad hoc) network
  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-computer-to-computer-ad-hoc-network

  Ad hoc networking - how the network with the funny name can make your life easier
  http://Windows.Microsoft.com/en-us/Windows-Vista/ad-hoc-networking-how-the-network-with-the-funny-name-can-make-your-life-easier

  How to build a wireless network without using a router at wide band (also Windows 7)
  http://www.hardwaresecrets.com/article/how-to-build-a-wireless-network-without-using-a-broadband-router/418

  Build a Wireless Home network without a router (also Windows 7)
  http://www.labnol.org/software/wireless-network-without-router/11494/

  How to share files and printers on your network
  http://www.hardwaresecrets.com/article/how-to-share-folders-and-printers-on-your-network/247

  -------------------------------------------------------------------------

  Other solutions include the use of these that turn your WiFi PC into a virtual router
  instead of using the ad hoc network.

  Connectify
  http://www.Connectify.me/

  Virtual router
  http://virtualrouter.codeplex.com/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Printer all in one HP3520 - how to select the wireless network and enter the WEP key?

  According to print my wireless network is detected.

  How to connect the! @# % printer $ fo the wireless network and enter the WEP key?

  Instructions on the HP site tell me to selet NETWORK on the printer control panel.  Well, there's a way to select the NETWORK from the control panel.  It is not an option for him.

  I downnloaded and installed the latest drivers.

  I have restored the default settings.

  How to select the wireless network and enter the WEP key?

  All of HP's instructions seem to be for a newer printer with a touchscreen.

  I want that the printer is connected to my main computer via the USB port.  I want to be able to print wireless phones and tablets.

  My 3520 is not a 'touch Screen' and it has wifi.

  However, the following work:

  Try to open the HP Deskjet 3520 icon, open the utilities tab, click on convert USB wireless, by following the steps on the screen.

  This leads me to believe that ONLY the wireless doesn't work.  I know now that the part of the sentence "Convert USB to wireless connection" is supposed to mean "works like USB and wireless.

  Thank you for your help

• How can I connect to the internet? Problems involving the network and sharing Center does not.

  Hello.
  I live in a House and bought a range extender so that I can get a connection in my basement as well.  I have installation range Extenders without problem.  When you install the range extender, I changed my name to my network router.  I changed the name of the network by typing 192.168.1.1 in my browser.
  The MacBook connects without a problem.  In the basement, the connection of Windows 7 works very well.  I have just connected Vaio Windows 7 my mother to the network, but it prompted that I enter the user credentials.  I read a post above and got that problem solved by opening the network and sharing Center and adding a new connection.  Now that the connection is configured correctly.
  The problem is with the laptop HP Windows Vista family basis.  Since I install the range extender, I can't connect to the network.  He had no problems before you connect the router or other networks to visit other places.  The new network name appears, but when I click it, it says I have to enter the user credentials.  I tried to manually, but the name is taken so I can't make a new and invites me to connect to the network that is established or to connect to a different network.
  • I tried to open the network and sharing Center, but it does not open.  When I click it, it opens a screen for a brief second.  The option "Display the status of network and tasks" opens either.

  • I logged as an Administration by entering the command line < net="" user="" administrator="" ctive:yes=""> > and restarted the laptop.  Even logged in as administrator, this folder does not open.

  • I also did a scan < sfc="" cannow=""> >.  The digitized rolled up with an error, but the error has been corrected.

  • I also updated the connection of the range extender.

  Why the network and sharing Center will not be open to the top?
  How can I configure my router my HP Windows Vista Linksys connection?
  Thank you.  Please let me know if you need more information.

  Thanks for your reply.

  In a last attempt, my sister has used the ethernet cable to connect directly to our router.  Next time, she turned on her laptop, she managed to connect to our wireless network and she was not invited to enter credentials.
  In this case, the manual connection helped solved the problem.

• Windows 7 64 bit... ""? "shows"See the whole map"in the network and sharing Center window"

  Hi guys

  I've been struggling with this problem for a few weeks and need help. When I open the control panel; Network and Internet; "Network and sharing Center", at the top of the page to the right, I have an option to view the connections of the network (see map). The opening I find a big blue '? ', with 2 solid lines from my computers to the "?", with the word "Unknown"under the present'?", then 2 solid lines go to the router... It's a wireless network must therefore a double line broken and not solid and obviously not '? I can fix this problem by changing the Properties tab 'Advanced' from the WiFi transceiver on each of the computers. Once I click OK, the computer the fact thing... and the blue "?" disappears and the network is 100% functional. Putting computers into sleep or restart... and I have the '? ' on the respective computer which itself was removed from the network after a reboot. This happens on 4 computers on the network, all the Windows 7 64-bit, 2 notebooks, desktop computer 2!... Still problem, all corrected in the same way. Until the '? ' is corrected I show other computers in our network at the bottom of the window under the label:-"the following peripheral discovered may not be placed in the plan.» Click here, etc. etc. Once all 4 computers are patched, I show a perfectly displayed network... I'm open to any ideas... Thank you

  The question mark appears when you return from sleep if interconnect them (Network Interface Controller) is allowed to turn off to save power.
  This can be disabled if you wish

• How to activate the Internet connection on the network and sharing Center.

  

  I clicked on disable when I opened it. I tried to find a solution to this, but I can't find anywhere on the web. Please, help me difficulty find my internet connection. I'd really appreciate it. It's windows 7.

  OT: I accidentally disabled the internet connection by going to network and sharing Center

  Thank you.

  Hello
  I suggest you to run the network troubleshooter utility.

  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  See also the link: wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Post us the results after trying the steps above.

• Virtual WiFi not presentation, it disappears from the network and sharing Center.

  Original title: Virtual WiFi not presentation

  Hello

  I created Virtual Wi Fi cmd (netsh wlan), first it was created and posted his icon in the network and sharing Center, after that show how I disabled it from the network and sharing Center by clicking on the icon and pressing the button disable I pressed off it disappear from the network and sharing Center.

  Can someone help how to activate it so that I see her back icon in network and sharing Center.

  Thank you

  Hello

  You have virtual map of Wi - Fi enabled in Device Manager?

  This problem may occur if network settings are changed.

  You try to run the following command check if it helps.

  a. press on the key Windows + X.

  b. click on (Admin) command prompt.

  c. type the command netsh wlan start hostednetwork and press on Enter.

  If the problem persists, I recommend posting your query in the TechNet Forums to get help:

  8.1 Windows networking forums

  Let us know if you need help with Windows related issues. We will be happy to help you.

• Network and sharing Center will not be open in the Panel

  I've been away from home - where I HSI and it works very well - for a few months, I plugged to the network sporadically awireless (sometimes just bad signal), with a lot of frustration.  A few days ago, I went to a place where I could connect to a hard (secure) wireless network and enjoyed the smooth navigation for about an hour.  Later when I tried to connect to the smaller network, unsecure, I couldn't open my network and sharing Center. Whether from the drawer or the Control Panel, a screen opens displaying nothing, but the circle of rotation.  The TASK MANAGER IS REQUIRED to CLOSE THE PAGE - it will not answer the close box. TM shows the centre network and sharing as 'running', although there is no indication on the screen, except the title and the circle of rotation.

  My laptop is a dv6t Pavilion with Windows 7 (64-bit)

  All the other files in the Panel seem to open and operate normally.

  Hello Hamanslayer

  Thanks for posting on the HP Forums!

  I understand the network and sharing Center will not be open. I will do my best to help you! If please launch and center network and sharing, and wait for him so that he can provide an error. In addition, please try to run Centre network and sharing in a different user account. If you don't have one, create one.

  I did some research on this issue. Unfortunately, the only reliable troubleshooting that is remaining, if the above does not help, is to reinstall the operating system. Too, there are different issues that could be causing it. Reinstalling the operating system will focus on each of them.

  First, please save all the files you need. You can find specific steps on how to proceed in the following HP document: backup of files (Windows 7)

  Once this is done, you can safely reinstall the operating system. I'll also give you a document on how to do it: perform a recovery of the system (Windows 7) HP

  Please let me know your results. Thanks again for the display on the HP Forums. Have a great day!

  Mario

• Windows Vista connected online but not shown on network and sharing Center or on the taskbar, leads to other problems

  I have a Dell Inspiron 1520 running on Windows Vista, my router modem is a Motorola SURFboard SBG901. A few months ago on this computer, I couldn't see that I was connected online either from right down icon in my taskbar (it shows just two monitors with an 'x', that when you highlight on he says "not connected, you are currently not connected to any network.")  I don't see it on my network and sharing Center which States: "not connected wireless connections are available." In terms of network it shows that my PC and then the line that has an x on him. If you click the x, or select diagnose and repair, he informs me that all is going well with my computer. If I go to connect to a wireless network, it shows that I'm connected to my network ready. I open one of my browsers and they all work very well, I can access any site without problem. I was not embarrassed with him at the time, but since then I moved into a new House and have a new service and everything, with this motorola modem cable. my new wireless network is a network unsecured, which of course, I want to fix it. I can connect to this network, but I can't access it through Windows properties to make sure. I read the manual of the modem, telling me to connect through an ethernet connection and access configuration manager using the ip address of my router on a browser, but which does not charge or the other. I have other devices (Ipod Touch and PS3) wireless I got other people come computers and they all detect the network but cannot connect to it. Thanks for any help.

  Hello
   
   
  I would like to ask you a few more things.
  1. how many network connections you have created?
  2. are there multiple NICs installed on the computer?
   
   
  Since this is a common problem and many users have solved this problem by using different methods.
   
  This can also occur if you frequently use several type of internet connections such as dial-up, Ethernet and LAN.
   
  As the article below also indicates that there could be multiple reasons for the same.
  The network adapter icon incorrectly displays a red "X" in the window management in Windows Vista network connections when the network adapter is connected
  http://support.Microsoft.com/kb/945925
   
   
  Method 1.
  I ask you to remove any network connection if you have created and then check.
   
   
  Method 2.
  For control please check in mode safe mode with Networking if the problem exists.
  Here's how:

  a. restart your computer.
  b. when the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 on your keyboard key repeatedly until you are presented with the screen Windows 7 Advanced Startup Options.
  c. using the arrow keys, select the desired option of Mode without failure.
  d. press the Enter key on your keyboard to boot mode safe mode of Windows 7 with networking.
  e. when Windows starts, use check and Internet explore if the problem persists.

  For more information, see the articles below.

  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

   

  Troubleshooting in safe mode
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshooting-problems-while-in-safe-mode
   
   
  I hope this helps.
   

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Network and sharing Center shows not connected, but the computer is connected to the wireless network

  When I open the network and sharing Center, or hold my mouse pointer on the icon of internet connection in the bottom right of the taskbar, it shows that I'm not connected to a network. However, I know that I'm connected to the internet. My internet and e-mail work correctly. Also, when I click on the 'Connect to a network' option, find the list of available wireless networks, and it shows that I'm connected to my home network. How can I make Windows everywhere where I am connected to the internet, instead of recognizing only on the list of the networks without wire-available?

  Had exactly the same problem on Windows 7 (win7). Connected to the Internet but the status showing no connection and a red cross on the network icon. Problem has also caused problems to connect to Lync and Office365 along with VPN, which apparently uses the status to check whether the connection is available.

  Found the solution here: http://social.technet.microsoft.com/Forums/en/w7itpronetworking/thread/df17c593-e78f-4878-97b0-7569307934c5

  Apparently, certain permissions gets hurt in the database record and must be fixed using RegEdit. The solution is a step by step and likely to be resolved simply by removing a cache of file using RegEdit and potentially affecting certain permissions.

  It will be useful.

• restore service dependency for the network and sharing Center

  How to restore the dependency service or group who couldn't start for network and sharing Center?

  Hi patto1708,

  If it was something that was already previously and failed after certain activities on the computer for which you are not aware of, then the best possible thing to do is run a system restore. This will ensure that your computer is back to operational status.

  For more information about the system restore, you can see the link: http://windows.microsoft.com/en-US/windows-vista/System-Restore-frequently-asked-questions

  Or you may need to check for the dependency of the network and sharing center services and start them manually when they are stopped manually.

  See the link: http://windows.microsoft.com/en-US/windows-vista/Manage-services-in-Windows-Vista-from-Windows-Vista-Inside-Out to learn more about how to manage services in Windows Vista

  Kind regards

  SAP U G - Microsoft Support