How do I disassemble the Tecra 8100

Similar Questions

• Using ISA cards in the Tecra 8100/8200 docking station

  Is it possible to use old pc ISA cards in the PCI slots in the Tecra 8100 docking station?
  The Deskstation V Plus for the 8000 series seems to allow dual use in some of its slots so I wonder if it's the same for the 8100/8200 series.

  You can also the Tecra 8100 can be anchored to the Deskstation V to allow access to the ISA slots?

  Hello

  where did you get this with the AIS in the PCI slots? I've never seen a combo slot in my life so I can't believe :)
  But what about the v: Deskstation

  Yes, it can be anchored, it s integrates without problems, then you will be able to use the ISA-machines built slot.

  Welcome them

• How to control the Tecra 8100 restoration?

  Hi I have a Toshiba Tecra 8100 and I can't boot the laptop whenever I start it it know that the System 32 file is missing or curropted doesn't ne1 know how I can master restor originally withouit factory setting have to have a cd - r. Thank you ryan

  Hello

  If you want more info on this problem, check it please this page http://support.microsoft.com/kb/833767/en-us Microsoft

  In my opinion the best solution is to reinstall the operating system using supplied recovery media. On this way the unit will be factory settings and will be absolutely clean preinstalled.

  If you need more suggestions please write again.

  Good bye

• Disassemble the dimension 8100

  I want to disassemble a dell dimension 8100. The manual tell you how to get off the hood of the cpu fan.

  Help appreciated.

  Edit: Has managed to get down after looks etc.-

  The Shroud is attached to the rear.  The heatsink fan is connected to the plug. You must press the levers on the side to release the heat sink.  This model is so old that it is not worth fixing.

  

  

• The Tecra 8100 with a CD - RW or a dvd upgrade

  Hello
  I'm a bit of a beginner, but I hope it's a simple question - can I put my tecra 8100 with a CD - RW, or combo dvd cdrw drive? I think I've read enough to know about changing caddies & Hubcaps etc - I don't know which drive would work - SD-R2102?
  Any help gratefully received. !

  Concerning

  Tony

  I also have a toshiba tecra 8100 and I use the cdw/dvd toshiba sd-r2612 and its perfect works
  I can play the dvd movie and burn cd

  Greetings
  RAF

• How does 3G on the Tecra M10 - 11V?

  I don't know how the capablilty of the 3G works on the Tecra M10 - 11V.

  A few ideas come to mind. With a different (a lenovo laptop), I noticed that the chipset integrated 3 g Vodafone is blocked. I also saw on another laptop space for a SIM card from a network of my choice.

  Judging by the previous posts, it seems that there is a space for a SIM card in the laptop.

  Anyone would be able to elaborate on this?

  Thank you very much!!
  Jon

  Remove the battery, you know a SIM slot?

  My friends Tecra M9 has a 3G slot and it can use any SIM. To make it work under Windows, it had to enter the proxy of suppliers in 3 G connection manager, then he worked :)

• Take a snapshot of a lun SAN: How do I disassemble the virtual machine?

  SAN is FC 9958E Hitachi, ESX 3.5 update 2.

  I try to take a snapshot of a lun (with a virtual machine in this regard) san and must turn off the virtual machine and disassemble the VMFS virtual machine so I can do that there is no I/O will the lun when I take the snapshot.

  How can I (of) a virtual machine of the VMFS without making the other virtual machines running in the same cluster? I know that the VMFS is a system of shared files grouped campaigns, exclusive property of vmware. Does anyone know the command to use?

  If anyone has any info on this subject, it would be great.

  This is the documentation is 1.5 ESX, released in 2002.

  The command no longer exists in recent versions.

  -Matt

  VCP, vExpert, Unix Geek

• How do I disassemble the Satellite P200-12U to clean

  Hello

  Sorry for my English.

  I would like to disassemble my P200-12U. I am looking for the schematic.
  My laptop is not guaranteed.
  My hot graphics cards and my laptop down. I want to clean it up.

  Thanks for your reply.

  Hello

  The procedure of disassembly notebook is very complicated and delicate!
  Usually, it's not easy to do this and in most cases that it s undesirable because it could damage other parts.

  If your laptop turns off automatically, then it means that the cooling modules don't work properly and can not cool the CPU or GPU correctly.

  I had this problem too, but might solve this cleaning of the fans.
  But guess what? I didn't disassemble the laptop but I cleaned the modules of cooling using a jet of air only!
  Using a jet of compressed air, you can remove the dust very easily and it works!

  Check it!

  PS: you also use the Toshiba graphics card driver because these drivers support the overheating protection.

• How do I disassemble the printer so I can work on it properly without breaking?

  Need to disassemble the chassis work printer without damaging it. Is there any diagram that I can look if I'll be able to do this with damage them the machine?

  Your request is beyond the intended scope of this forum.

  You can describe a problem you are experiencing with your printer in terms of software, installation and configuration. We will do our best to help you with that.

  Disassembly of printers is not something in the forum.

• Tecra 8100: Advice replace please - audio card?

  My 8100 Tecra faithful and beloved which is ideal for my purposes locked up the other day, in the middle of a session.

  Restart windows resulted in blocking machine once Windows is running.
  I started in safe mode - no problem.
  I have disabled all devices useless and then through a process of elimination of selectively allowing devices and reboot.
  I found that the problem was the Yamaha audio device - that turn on the machine and it would lock up, disable that and he would normally go.
  It worked fine now for a day with the disabled Yamaha audio device.
  I tried to uninstall/reinstall the device - no change.
  I even did a fresh install of XP - no change.

  I ran XP pro for over a year without problem (so far) and I consider not audio as criticism - just a nice to have.

  My questions are:

  Is there anything else I need to do in the way of diagnosis?

  Tips for common problems?

  Can anyone with experience of fixing these machines or similar notice if replacement of all of the audio card is likely to make a repair?

  I seem to remember the last time that I opened it about two years ago to change the processor that the audio Assembly was on a separate panel but is that all?

  Note that this is a _ancient_ machine and _not_ going to be taken to a repair shop where the Bill would be more that it is worth! I am competent to replace the sound card, more than that and I will probably continue to run without audio - I don't think that it worth replacing the motherboard just for audio...

  Thank you very much in advance for any constructive suggestion.

  Well, as you know these replacements are very delicate
  However, I don t think you will be able to replace this sound card but it s my personal opinion.

  From my experience, I know that the card (audio driver) his Yamaha is not fully compatible with Win XP SP1 and SP2. Update the audio driver is necessary.

  Google for it

  I searched a bit for some instructions how to remove these boards and found this page.

  There you should find a link to the page how to disassemble the Tecra 8100.
  http://repair4laptop.org/disassembly_toshiba.html

  Greetings

• Tecra 8100: How to enter the BIOS

  BIOS settings made using Toshiba Windows utility or how I
  Enter the BIOS during boot? What button I push on?
  Thanks in advance for answers!

  Hello

  Yes, you are on the right track.
  The most common BIOS settings can be changed in the Toshiba HWSetup utility.
  But it seems that the Tecra 8100 uses a Toshiba BIOS, and so you should be able to access the BIOS by pressing ESC and F1.

• Tecra 8100, upgrading the BIOS, whitch that hard drive is taken in charge (40 GB)?

  Hallo,

  I have an old Tecra 8100 one I want to update BIOS. Who knows who is supported (20 GB, 40 GB) hard drive and where can I find the specifications?

  Thanks for your information.

  Georg

  Hello

  As I m wrong not the Tecra 8100 does support an IDE HDD controller.
  In this case, it should be possible to use the 2.5 IDE HDD.

  I can't say much about the formats supported, but the fact is that the size of HDD supported depends on the HARD disk controller. The old controllers IDE up to what the ATA - 5 (also called Ultra ATA/66 or Ultra DMA/66) supported LBA 28 bits, which allows you to use the 120 GB HARD drive max.

  Since ATA - 6 (also called Ultra DMA mode 5 or Ultra-ATA100), you can use IDE hard drives of more than 128GB.

  So if you want to, you can check your IDE HDD controller using a hardware diagnostic tool (IE Everest home edition). Then you might find out what IDE controller is and what drives are supported.

  See you soon

• You cannot change the color display on Tecra 8100

  I have a 8100 TECRA with Windows 2000 Professional installed. I tried to install "Streets and Trips" and it won't work without colorful. I can't change the view setting because it doesn't have this option (high resolution). Is there a driver available to fix this problem?

  Don

  I found on the Toshiba page two graphic drivers for W2k on the Tecra 8100.
  Just install the graphics driver and the option should be available

• Question about the Bios Tecra 8100 2.5

  Hello
  I installed the latest version of the Bios on my tecra 8100. My Question is, what is the maximum size of hard drive for these phones? Now I have 13 GB hard drive, but I want to have a bigger. And 512 MB of Ram is the maximum, right (2x256mb)? Can I adjust the size of the videoram?

  In my view, the tecra 8100 is a laptop very well.

  Greetings,
  Stephan

  Hi Stephan

  You are absolutely right. 512 MB of RAM is max for this pretty portable. If you want to buy more RAM I will suggest you that a PC100 256 MB (PA3051U-1NME). This RAM is tested and working properly with your device.

  Sorry, but video RAM is not possible to extend. And now something on the HARD drive. Unfortunately there is no documents where you can find information like this, but I know very well that here should not be a problem with 30 or 40 GB of HARD drive.

  I wish you lots of fun with this laptop old but nice.

• Tecra 8100, connection to the internet via a Vodafone data card

  I'm having extreme difficulties, the tecra 8100 recognizes the card etc etc, but will not let me create a profile and when I try to connect to the internet tells me that the card cannot be found... Gray goes with it - have disabled the internal modem and told my system to use the card... Help

  Hello

  Do you have software for this card? If so, you should try to re - install the software.
  But in my opinion you should contact Vodafone support because they have more experience with own products.

  Sorry

  Good bye