Similar Questions

• IMAQ under Win XPx64 with PCIe-1433

  I have an IMAQ application written with VS2008 (managed C++, using PInvoke). The 32-bit version works fine. But I want to build a 64-bit version.

  I have IMAQ 4.4.0 (March, exit 2010) installed. My framegrabber is a PCIe-1433. I am running Windows XP Pro x 64 on a machine of BOXX Technologies.

  When I build an x 64 version, I get the error 0xBFF60150 of imgSetBufferElement (...) IMG_BUFF_ADDRESS...). imgShowError tells me that this means "the operation is not supported for 64-bit applications."

  This error means I can't do a x 64 build with IMAQ under XPx64?

  Or does this mean that one of the parameters to imgSetBufferElement (...) IMG_BUFF_ADDRESS...) is incorrect?

  Thanks in advance.

  Hi jhc2,

  If you look at the signature for imgSetBufferElement, you will see that the value of parameter is defined as a uInt32. It is not compatible with a 64-bit being the pointer 64 bits wide application. If you take a look at the C examples included with your version of IMAQdx you can see how the replacement function imgSetBufferElement2 must therefore serve as a replacement in the new code (imgSetBufferElement should now be listed as "obsolete" in the header). The new version replaces the old version of the function and is compatible with 32-bit and 64-bit code. The syntax and parameters that are passed must be identical.

  Eric

• OR PCIe-1433 grabber in project VI

  I have a LabVIEW project where I can set up the camera is connected to the NI PCIe-1433 map. But I have to close and open NI MAX to view the video.

  Is there an example on how to pull the stream into a LabVIEW project video? I know I've seen this before with webcams and a cRIO.

  Hi Jason,

  It's good that you can see and acqurie images from the camera in MAX. I advise to use some of the expedition to start. You need get the MAX interface, for example 'img0' name and use it as input to the Init.vt IMAQ.

  You can access the latter in LabVIEW by going to help-> find examples-> hardware input and output-> Vision Acq-> NI - IMAQ-> high level-> HL Grab.vi

• Time of exposure with MC1362 externally triggered and PCIe-1433

  Hello

  I'm capturing images with the help of a Microtron EoSens CL MC1362 camera and NI PCIe-1433 acquisition card. I have a question about exposure times - I don't know if it is related to the acquisition, the camera or the combination card, but I hope someone here can help you.

  I'm running an external signal to the SMB connector on the card acquisition and the camera set to run in "Mode Pulse width", that allows to the capture card to take control.

  My question is:

  How can I determine the exposure time in the settings of the external signal? It is a square wave, and the cycle seems to control the exposure time.

  I guess the exposure time, E = (D/f), where f is the frequency of the signal and D is the duty cycle? for example, for f = 1 kHz, and D = 80%, exposure would be E = 0.8ms. Is this correct?

  The manual of the device can be found here:

  http://G4.com.tw/Web/file/product/UserManual/995-EoSens%203CL-MC1361-manual.PDF

  and I've included a screenshot of the revelant portions that seem to describe how the pulse width. In particular, he said "exposure time is defined by the width of the external signal. Which is equivalent to my idea of E = D/f?

  Thanks in advance for any help.

  

  This looks good to me.  The exhibition remains on while the pulse is high.  When you calculate E, you're just calculating the duration of the pulse is on.

  Bruce

• Basler spL2048 - 70km with card PCIe-1433, low cadence

  Dear community LabView,

  I'm trying to run a Basler Sprint Mono spL-2048-70 km with a frame grabber module NI PCIe-1433. While the initial start-up was plug-and-play, turning the camera to the specified maximum speed (300 kHz) proves to be a challenge.

  Namely, I use the camera with a trigger in burst mode (main trigger frequency 10 Hz + burstmode up to 300 kHz) but the maximum reproducible work rep for the burst rate is around 30 kHz. I tried various options to increase the overall pace over the last few days but hit a wall.

  The system is a desktop based Win 7:

  Win 7 Enterprise SP 1

  Intel Core i5-2500 @ 3.3 GHz

  8 GB ram

  64-bit system

  I have attached the sample code I use below. Its the first time I tried to create fram high rate of requests so I hope it's just a very obvious mistake that can be fixed quickly and elegant.

  Thank you very much in advance

  Dear NIko,

  Thanks again for your involvement.

  I found yet another entry in the forum which helped me a lot.

  https://forums.NI.com/T5/machine-vision/acquisition-rate-is-half-of-trig-rate-why/TD-p/2029160/page/...

  Even if it of another camera and resembles another question originally it solved my problem. It seems one must trigger the acquisition card in ' Action: trigger start of acquisition "mode and the device itself in" exposure control: triggered "in order to avoid long latencies and reach higher than 100 kHz framerates.

  Brief overview:

  -use the Vi posted

  -define the Framegrabber Action: trigger the start of the acquisition

  -define a camera exposure control: triggered

  -Use 512 pixel AOI (via Basler CTC +)

  -OR-Max allows you to set the source of external camera command-line (moving the switch directly to the camera)

  --> Aquire burst mode with frequency intraburst up to 200 kHz (not sure if about 200 kHz creates problems)

  ---> be happy

  The specification from the point of view, the camera must be able to still 300 kHz. The frequency of my goal is 200 kHz I see this issue as resolved.

  Thanks a lot for your help and I hope this helps the rest of the community, and

• INSTALLATION OF PCIE-1433

  I try to install a PCIe-1433 and I'm not able to get (1) image, and (2) a single camera 0 is available.

  I install the Software NI Vision Acquisition on a CD, dated September 2011 that includes NEITHER-IMAQ 4.6.1, NOR-IMAQdx 3.9.1 and NOR-IMAQ1/0 2.5.  I have two cameras Imperx Bobcat 1610 I want to operate simultaneously.  When I run the Configurator of Bobcat, he only found a camera and works as expected for that camera.   To see if there is a problem with one of the cameras, I linked each in 1433 one at a time.  The Bobcat Configurator found two cameras but only when they were connected to the farthest port 1433 of the input trigger.

  When I open the peripheral OR-IMAQ able and Automation Explorer tab, I get the following response

  img0:NIPCIe - 1433

  Channel 0: Basler A504K

  Which is consistent with the Bobcat Configurator doesn't find just a single camera.

  If I click on the Basler A504K, I get a video window with tabs to SNAP GRAB etc.

  If I click on the snap-IN or GRAB software component tab, I get the error message can NOT DETECT UNMISTAKABLE VIDEO SOURCE.

  The 1433 doesn't seem to be visibly damaged.  I don't know if I have installed the appropriate software or using the MEASUREMENT and AUTOMATION EXPLOER CORRECTLY or have a hardware problem

  Thank you

  FETHIBELFODIL

  fethibelfodil,

  You are looking in the PCIe-1430, because it is our only capture card that supports two buses cameralink.  However, be aware that two cameralink cameras must use the basic configuration.

  Kind regards

  LVbum42

• How can I see in LabVIEW if an axis is enabled or disabled?

  Hello!

  I know not how to set the axis in enabled or disabled, but how can I see if the command has been executed when you use LabVIEW?

  I use a movement card 7340 PCI with encoder feedback.

  Concerning

  OLA

  Sorry, I noticed just this VI is not compatible with cards 73xx !

  

  Give reading by axis Status.vi to try. According to below extract assistance, I'm not shure if the Motor Off bit will reflect the State enabled axis.

  

• My computer with two hard drives and 2 starting systems has the car crash in the solid state. When I got the new drive and tried to restore from time capsule, I lost some data. How can I see what backups are on the time capsule? My laptop is also backed u

  My computer with two hard drives and 2 starting systems has the car crash in the solid state. When I got the new drive and tried to restore from time capsule, I lost some data. How can I see what backups are on the time capsule? My laptop is also saved to the time capsule. Everything is in 'Data' when I look through the Airport utility. I think that the information that I've lost are still there since I was a Capsule 3 to.

  Time Machine backup to a sparsebundle.

  The sparsebundle will use the share name of computer. So, it should be obvious who is your Macbook and that is your Macpro.

  Open the sparsebundle in Finder and keep open the subfolders until you get to the backup of each separate hard drive...

  You has of course set the exclusion in Time Machine?

  By default, Time Machine will exclude your second drive unless you have included it. Did you?

  Once you get to this level during the backup, you can do a full restore manually whenever you want.

• How can I see external drives on the sierra?

  How can I see external drives in sierra?

  Menu Finder Preferences... > General

• How can I see activity of Time Machine in Console with macOS Sierra.

  In OS X, I just typed "backupd" in the Console-search window.

  Now, it seems more complicated.

  Jur Kuipers, Netherlands

  Let me rephrase the question...

  How DO I SEE ACTIVITY TIME MACHINE in Mac OS Sierra WITH CONSOLE?

  also... Time Machine takes forever...

  See thread Re: Sierra and Time Machine

• How Windows users see my iCloud shared photo album?

  I created an album with iCloud Photo Share.

  Among those invited are some hardcore with no iCloud account Windows users.

  How can they see the photos? I do not have the public album if there is another way?

  Thanks in advance

  See these -.

  http://www.windowscentral.com/how-set-and-use-icloud-photos-Windows-10

  iCloud: create a shared album

  iCloud, sharing photos - Apple Support

• How can I see what I have stored in iCloud?

  How can I see what I have saved in my different devices iCloud?

  Here's how you can visualize what you have stored.

  Manage your iCloud - Apple Support storage space

  Hope this helps, good luck to you.

• How can I see the list of authorized computers (not how)?

  Hello

  I would need to see the list of computers that are allowed before removing all permissions.

  How can I see the list of the authorized computers (not how I have)?

  Thank you

  There is not one available from your end.

  (144073)

• Firefox is no longer allows me to see my passwords saved to bookmarks. How can I see them now?

  He used to be a button at the bottom of the show all bookmarks that allowed me to show my passwords saved. This button is gone. How can I see my passwords saved to my favorite sites?

  Hello, you can view the saved passwords in password manager: Password Manager - don't forget, delete, modify and import passwords saved in Firefox

• How can I see how much I have to pay?

  How can I see how much I have to pay? My little sister play Sims on my phone and buy something, but I do not know what and how much cost? Thank you.

  < re-titled by host >

  You can view the purchase history full of the account through iTunes on your computer: see your purchase history in iTunes on Mac or PC - Apple Support store

  You can also view past purchases for 90 days by http://reportaproblem.apple.com