How IPsec counterparts know remote peer is dead?
How IPsec counterparts know remote peer is dead? Now, I need config IPSec between a Cisco router and the other router in a case, but the cisco router can not know the remote peer is dead, so the IPsec conversation cannot switch to a different path when the primary path is down
How the cisco ipsec Protocol can detect the dead to implement ipsec other providers?
They do not. There is nothing in the ipsec specification to make it work. Cisco has a patented method that they added as an optional parameter for many of their devices, but given that a device not cisco into the mix, you're out of luck.
Your only option is probably declining life expectancy of the SAs, so that they are renegotiated more frequently. This will probably increase above if
Tags: Cisco Security
Similar Questions
-
someone was able to access my laptop remotely today, how would I know if they let any virus or spyware on it. I have norton 360 virus protection that has not detected any viruses. IM worried about using my computer to stuff order online where they can steal my credit card details / number while im using it
Hello
How do you know that someone will access your computer from outside? Allow access and do you
you know who it was?Here is some information that should help you:
Was it a SCAM phone call that initiated the connection distance:
Avoid scams to phone for tech support
http://www.Microsoft.com/security/online-privacy/avoid-phone-scams.aspxIts a total scam. Uninstall their software and then perform a system restore before you install.
Change all your sensitive passwords at all sites - e-mail, Bank, credit cards and others. (Do not
on the computer compromise and it would be better to do it on the phone or in person.)You can even restore your system to factory fresh to make sure their software violates not
your security. (Ways to re - install Windows Clean - removing everything on the backup drive so all the data
before hand.)It is also possible that they consulted Bank, passwords and information of credit card on your computer. If
in order to check for malicious software as shown below. Change your passwords. Contact the Bank and credit
phone card companies. Do the same for any investment or other sensitive professionals or personal
accounts that may have been violated.====================================================================
====================================================================In the United States, you can contact the FBI, Attorney general, the police authorities and consumer
Watch groups. Arm yourself with knowledge.No, Microsoft wouldn't you not solicited. Or they would know if errors exist on your
computer. So that's the fraud or scams to get your money or worse to steal your identity.Do not fall for the fake phone Tech Support
http://blogs.msdn.com/b/securitytipstalk/archive/2010/03/09/Don-t-fall-for-phony-phone-tech-support.aspxAvoid scams that use the Microsoft name fraudulently - Microsoft is not unsolicited
phone calls to help you fix your computer
http://www.Microsoft.com/protect/fraud/phishing/msName.aspxScams and hoaxes
http://support.Microsoft.com/contactus/cu_sc_virsec_master?ws=support#tab3Microsoft Support Center consumer
https://consumersecuritysupport.Microsoft.com/default.aspx?altbrand=true&SD=GN&ln=en-us&St=1&wfxredirect=1&gssnb=1Microsoft technical support
http://support.Microsoft.com/contactus/?ws=support#TAB0Microsoft - contact technical support
http://Windows.Microsoft.com/en-us/Windows/help/contact-support===========================================================
===========================================================Follow these steps carefully:
If you need search malware here's my recommendations - they will allow you to
scrutiny and the withdrawal without ending up with a load of spyware programs running
resident who can cause as many questions as the malware and may be more difficult to detect as the
cause.No one program cannot be used to detect and remove any malware. Added that often easy
to detect malicious software often comes with a much harder to detect and remove the payload. Then
its best to be thorough than paying the high price later now too. Check with them to one
extreme overkill point and then run the cleaning only when you are sure that the system is clean.It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
the regular windows when you can.TDSSKiller.exe. - Download the desktop - so go ahead and right-click on it - RUN AS ADMIN
It will display all the infections in the report after you run - if it will not run changed the name of
TDSSKiller.exe to tdsskiller.com. If she finds something or not does not mean that you should not
check with the other methods below.
http://support.Kaspersky.com/viruses/solutions?QID=208280684Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
(If Rootkits run UnHackMe)Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Malwarebytes - free
http://www.Malwarebytes.org/products/malwarebytes_freeSuperAntiSpyware Portable Scanner - free
http://www.SUPERAntiSpyware.com/portablescanner.HTML?tag=SAS_HOMEPAGERun the malware removal tool from Microsoft
Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.
You should get this tool and its updates via Windows updates - if necessary, you can
Download it here.Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
(Then run MRT as shown above.)Microsoft Malicious - 32-bit removal tool
http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=enMicrosoft Malicious removal tool - 64 bit
http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=enalso install Prevx to be sure that it is all gone.
Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
here or use Google to see how to remove.
http://www.prevx.com/ <-->-->
http://info.prevx.com/downloadcsi.asp <-->-->Choice of PCmag editor - Prevx-
http://www.PCMag.com/Article2/0, 2817,2346862,00.aspTry the demo version of Hitman Pro:
Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
(viruses, Trojans, rootkits, etc.). who infected your computer despite safe
what you have done (such as antivirus, firewall, etc.).
http://www.SurfRight.nl/en/hitmanpro--------------------------------------------------------
If necessary here are some free online scanners to help the
http://www.eset.com/onlinescan/
-----------------------------------
Original version is now replaced by the Microsoft Safety Scanner
http://OneCare.live.com/site/en-us/default.htmMicrosoft safety scanner
http://www.Microsoft.com/security/scanner/en-us/default.aspx----------------------------------
http://www.Kaspersky.com/virusscanner
Other tests free online
http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1--------------------------------------------------------
After the removal of malicious programs:
Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
system files.Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-----------------------------------------------------------------------
If we find Rootkits use this thread and other suggestions. (Run UnHackMe)
======================================
If necessary AFTER THAT you are sure that the machine is clean of any malware.
How to do a repair of trouble Windows 7 installation (it's for Windows 7 and there are similar procedures
for Vista if necessary.)
http://www.SevenForums.com/tutorials/3413-repair-install.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
How will I know if my battery is dead, or I have a bad cord?
My battery will not charge when plugged in the power cord. How will I know if my battery is dead, or I'm wrong cord.
See: How to check and repair a battery discharged the laptop or netbook
-
Hello
By train I got a remote access IPSec VPN, when I have all the performed configuration and try to access remote show software vpn client (cisco) the following message:
"The remote peer is no more answers.
I know where is the problem.
Network information:
ASA TO LAN - 1:
192.168.1.0 - 255.255.255.0
the interface vlan 1:
IP: 192.168.1.1 - 255.255.255.0
the interface vlan 2:
IP: 100.100.100.1 - 255.255.255.252
REMOTE LAN ACCESS:
192.168.10.0 - 255.255.255.0
ASA-1 configuration:
* IP address pool
local IP VPNPOOL 192.168.20.1 pool - 192.168.20.254
* Split tunneling
splittunnel list standard access allowed 192.168.1.0 255.255.255.0
* NAT configuration
object obj LAN
subnet 192.168.1.0 255.255.255.0
object obj-vpnpool network
subnet 192.168.20.0 255.255.255.0
NAT (inside, outside) 1 static source obj-local obj-local destination static obj-vpnpool obj-vpnpool no-proxy-arp* Group Policy
internal group company-vpn-policy policy
attributes of vpn-company-policy-group policy
VPN-idle-timeout 30Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list splittunnelConfigure the IPSec
IKEv1 crypto policy 10
3des encryption
sha hash
preshared authentication
Group 2
life 3600
Crypto ikev1 allow outside
crypto isakmp identity addressCrypto ipsec transform-set esp-3des esp-sha-hmac RA - TS ikev1
Dynamic crypto map DYN_MAP 10 set transform-set RA - TS ikev1
card crypto VPN_MAP 30-isakmp dynamic ipsec DYN_MAP
VPN_MAP interface card crypto outsideCreate tunnels
tunnel-group vpnclient type remote access
tunnel-group vpnclient-global attributes
address VPNPOOL pool
by default-group-company-vpn-policy
tunnel-group vpnclient ipsec-attributes
IKEv1 pre-shared-key groupkey123Where is the problem?
Hello
Configuration seems almost perfect. Please share the result of the following of the ASA when you try to connect.Debug crypto isakmp 200
Debug crypto ipsec 200You can take snapshots on the external interface of the firewall to confirm if the packets are reaching the firewall or don't use do not:
capture capx off match ip hosthost interface Kind regards
Dinesh MoudgilPS Please rate helpful messages.
-
I have recivied an email indicating that I need to load a security update. He referenced MS10-046 "a vulnerability in the windows shell could allow remote access" is this necessary? and it refers to the sp2. Which leads to my next question how can I know what "SP" I have on my computer. Thanks for your time and considerartion.
go to start > run > type
winver
Click ok
What service pack t - he say that contains?
-
How would I know that the patch for ms 10-002 is applied
I have ie8 with vista home os in my laptop, I want to remote connect to my desk in my office. Since this morning, he complains, I need to patch ms 10-002, I applied for several tiime use windows update, but this error still happens.
so, how would I know this patch is applied with success? is there any executable file that I can download to run it manually?
If the update installed successfully, Cumulative Security Update for Internet Explorer 8 for Vista (KB978207) or update of security for Microsoft Windows (KB978207) would be listed in Start | Control Panel | System maintenance and (if you use Classic view, skip this step) | Windows Update | View the update history (or programs & features |) Installed mises_a_jour).
=====================
Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy. If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.
~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft
-
How would I know that the patch for ms 10-002 is applied in my laptop
I have ie8 with vista home os in my laptop, I want to remote connect to my desk in my office. Since this morning, he complains, I need to patch ms 10-002, I applied for several tiime use windows update, but this error still happens.
so, how would I know this patch is applied with success? is there any executable file that I can download to run it manually?
Thank you.
Windows Update Forum:
It comes with Vista, upgrade install and activate Forum.
You will get the best help for any update/Service Pack problem or issue in the Windows Update Forum; the link below:
http://social.answers.Microsoft.com/forums/en-us/vistawu/threads
See you soon.
Mick Murphy - Microsoft partner
-
Hello
If you have a black screen which can be if the processor is dead or memory is dead how you know if you do not reserve memory, the problem is the processor or memory?
I tried this on my computer, I put on the CPU and I got black screen, I put in memory and I got black screen.
Thank you
Johan
Thank you
so in this case, how you can know if it is the processor or memory is the problem.
you have to always have book of memory by you to resolve these issues (to make sure if the memory is problem) what memory or processor its work not at all.
or it is too nested ways!
Johan
From what you described, it is possible that the processor, the RAM and the motherboard are all damaged. Or also the cold of power supply the problem (which could be checked for appropriate using a voltmeter). If you do not reply the existing motherboard then without spare parts (RAM, processor and motherboard) to use in tests, there is nothing more you can do with it to test these components.
-
How to get the remote object mode protect?
Hi all
I have a question for a remote object mode protect in drive x. need your help, thank you very much ~
Background: I have a plugin running on drive x protect mode. Without a strong name, plug-in will load my DLL (manufactured by c#). Then, in this DLL, it will use
_3rdProxy p (_3rdProxy) Activator.GetObject = (typeof (_3rdProxy), url); for a remote object of the 3rd application (made by c# also). Then I can make communication between my app plug-in and 3rd.
But I got an error "Access denied", said. Anyone know how to get the remote object in this case? Thank you very much ~
Since you have a reader integration key, you are advised to use our methods of support for the official Developer.
-
How can I know what ram slot ram in there on my G4 imac
OK so I have an imac G4 1 GHz version and I don't have any tools to open it to see what ram slots are empty for a ram upgrade how can I know what ram slot is free and opening the mac
There is a user accessible memory slot. You can install a maximum of 2GBs. The memory of the plant is pre-installed.
-
How to stop the remote control to the setting
How to stop the remote control to the setting
Disable the settings > general > accessibility > voiceover.
-
How will I know that I can trust a dictionary to download?
I went to download the English Dictionary (British) (smaller, longer version told was not compatible with this version of Thunderbird) but then my computer told me it was an unknown author and can contain malware. Probably just a generic warning, but how do I know dictionaries offered are safe? On my other laptop the dictionary is English (United Kingdom), he seems to have changed since the last time, I downloaded you bird.
I would consider a dictionary as safe when downloading from AMO (modules, Mozilla.org).
https://addons.Mozilla.org/en-us/Thunderbird/Extensions/language-support/ -
How will I know if it's a 32-bit or a 64-bit browser?
While trying to install Java Runtime Environment Plugin, I was asked this:
Should what download I choose?
Choose the 32-bit download to use with a 32-bit browser.
Choose the 64-bit download to use with a 64-bit browser.
If you use 32-bit and 64-bit browsers, you need to download Java 32 - bit and 64 - bit.So, how can I know if it's a 32-bit or a 64-bit browser?
Still, versions of Firefox from mozilla.org , including the current 37.0.2 is Win32.
So you need 32-bit Plugins for firefox Win32.
The 38.0 Firefox may be the first version to be built with Win32 Win64.
The WOW64 in your Firefox useragent is a Win32 on Windows 64-bit application.
-
How will I know when to load the mouse and keyboard on my IMAC?
IMAC late 2015. El Capitan version 10.11.5. 1.6 GHZ. Intel i5 processor. 8 GB.
How will I know when to charge my rechargeable keyboard and mouse? How can I tell when it is fully charged. Where can I find info on my IMAC so I must not ask about every little thing. The IMAC is new to me. Thank you
The iMac will appear a message when is running out of power. Also you can check the charge level of your device from the Bluetooth icon in the menu at the top of the screen bar.
Recharge the battery in your Apple - Apple Support accessory
-
How can I know what NVidia drivers are in el Capitan?
I'm trying to find the best combination of price and capacity for a video/graphics card to go in a Mac Pro 5.1 running el Capitan. NVidia seems to be the best choice for my type of work, but how do I know if the drivers from NVidia are integrated to the el Cap? I know that there is a possibility of losing the bootscreen, but what video advice may work in a Mac Pro on el Capitan?
You can download Nvidia drivers:
Presence or absence of a splash screen depends on the firmware on the map because during startup, no drivers are loaded. The start screen depends on the firmware on the card. A card flashed to a Mac has a bootscreen
Maybe you are looking for
-
I'm on 10.11.6. I tried to find the file "envelope" in the ~ library, but it doesn't seem to be there. I'll try to find major problems is search result does not give comprehensive results, the mails that I can find in IOS.
-
I could not format Satellite L40 - 18L
I have a * Toshiba Satellite L40-18 L *. The software is very slow and I decided to format it. But when it has been formatted it gorge yourself a mistake. When restoring amounts to 41% the pc showed something like "* error: C:\Windows\winsxs\x86_micr
-
Hello I'm using LabVIEW 2012 and there seems to be a problem with the node of the formula. The output of a simple no operation is not correct. I have an input U8, whose value is 255. I apply a no operation (a = ~ a and the value returned by the formu
-
"no memory to perform this operation? Help.
Hello While I was running an explicit signal project, a window pops up that says "no memory to perform this operation" and "memory is full" in the power spectrum. Then he paused data collection. I wonder where I can set up the maximum memory and let
-
I play runescape, but when I try to log in it says java not working and he had to get the latest version.