How NI PCI 4474 DSA detects an overload to the input channel?

Similar Questions

• PCIe-6259 anallog effect of clipping (perhaps overvolting) on other analogously in the input channels?

  Curious to know if the cutting/possible ovevolting on one of the analog channels would affect the performance of other similar channels. I have two systems, one where signals don't clip and the other channels are still operable. The other has some problems of cutting (which fade eventually btw) on some of the ins anlog. One with the cutting on other channels are apparently unusable while those who did no cropping entry seems to be well.

  I seem to be affected by a situation in which hanging on an analog channel makes so that other analog channels do not work.

  Curious to know if I can see what is expected?

  Anyone have an overview here?

  This is how it is supposed to work?

  We do not guarantee that all channels will work normally when you're in a State of fault/over-voltage.

  Since it is a MUX architecture'ed, that the channels are analyzed in order in the amplifier of shared instrumentation and ADC.  If the instrumentation amplifier is on track for channel 0 (for example), it will take some time to recover from this error after the next channel is enabled in.  This can cause a number of incorrect following channels (possibly indicated as being on track).

  Of course, we do not recommend to use this device in an error condition. When you said "analog channels does not" what do you mean?  The data on track?

  Some things that might help:

  -Slower sample which allows more time to settle the instrumentation amplifier

  -Skip the chain incriminated in the scan list

  -Make sure that the offending channel is set to the widest range of voltage (+/-10 v)

• How can I make a detectable 6000 microsoft wireless mobile mouse?

  Try to connect my mouse to my laptop which has bluetooth and wireless built in.   But the search did not see.  How do you do this detectable mouse so that the laptop can see?

  Most often when a device does not work, it's because the driver has been corrupted.

  Try reinstalling your.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

  http://captaindbg.com/how-to-update-drivers-on-Windows-7/

• How to detect if the cursor is no longer within the input text area

  Hello.

  My question today is:

  How to detect (in AS3) if the cursor is no longer within the input text area?

  I tried to mouse events, events, events in text but without success.

  Any ideas?

  Concerning

  If you have a textfield of entry with the instance name it '...

  it.addEventListener (FocusEvent.FOCUS_OUT, focusOutHandler);

  function focusOutHandler(evt:FocusEvent):void {}
  trace (evt. Target.Name);
  }

• During the migration of Firefox since Vista computer on windows 7, personal profile has been lost and I don't know how to restore - Profile Wizard detects no pr

  When data were transferred from my vista computer to the new computer windows 7, firefox profile has not been transferred to the new computer. Because the profile has not been transferred, the Manager profile, or by typing in the default location doesn't give a result. All the info on the website of mozilla that I looked at the way in which the profiles doesn't seem to work. I can probably recover and make a copy of the profile of the old computer, but how do I know where to put it on the new?

  Try to remove the profiles.ini file to force Firefox to create a new file profiles.ini and a new default profile.

  • http://KB.mozillazine.org/profiles.ini_file
  • 'C:\Users\Peter\AppData\Roaming\Mozilla\Firefox\profiles.ini '.

• How to make a clapping detection program

  Hello Im new on the forum. IM currently working on a program that lights up when you applaud. The trickiest part in which I can't find a way to do it is to make Labview only light the Leds when it detects the 2 claps.

  What I did is that I used the microphone on my laptop to acquire sound samples, then extract the samples in a table and also to extract the maximum of the table, and then after a few comparisons when the program detects a spike then the LED lights. But I can't find a way to run only if you do two claps. If anyone can help me please.

  (BTW sorry if my English is bad cause Im from a country of Latin America)

  Continuous sampling makes it easier to get the timing of the two summits.

  To create an example let define us two peaks as culminates more than 200 ms and less than 2000 ms interval. When we find a peak (max. 1) store the value in number of cycles (1 head) in the shift register.  The number of cycles is in milliseconds. The actual value means nothing to your program.  When the next peak is detected (max. 2) store the number of cycles at this time, count 2) in the registry change and subtract the number of cycles of previous peak (count 1 terminal point of the shift register to the left) of the current count (count 2) (connected to the Terminal on the right).  If there is a difference between 200 and 2000, the LED lights up, otherwise, leave off.  The next iteration of the loop to count 2 will take place on the left terminal of the registry to offset and counting 1 will be replaced. If no PIC is on this iteration just plug the register straight shift, now the number of values 2 in it.  When the third peak is found, its count will be compared to the number 2.  If you still have an old Chief (after finding the first pic) and no change for no new spike or a new account was a new peak.

  The various actions for pic or no Pic are in two different cases of a box structure.

  Lynn

• "Detect an error in the course of the PININST_BBV".

  I'm still working on the resumption of this problem that AxshunJaxun has been able to help me to diagnose properly.

  I have since received support from HP recovery and bought a new HARD drive that needs to be an improvement on the part of the plant. And I spent part of yesterday and most of the work now on the process of recovery without success (several failed attempts).

  I get a message "failed to retrieve" Application Recovery Manager with the message of the specific details of:

  [2:37:49.82] ChkErrBB.CMD: detect an error in the PININST_BBV.
  [2:37:49.82] ChkErrBB.CMD: check c:\system.sav\logs\BurnBootWarn.log
  [2:37:49.82] ChkErrBB.CMD: or, visit c:\system.sav\logs\BurnBootMerge.log

  (The two. LOG files do not exist on the C: partition, which is here.)

  I followed the process (initially had to hit ESC instead of F2) developed by anthony82 and met no error on drive testing HARD and memory.

  According to this message , it's probably a problem with the HP recovery media. anyone else seen this kind of problem and that this is the case also determined?

  DarkSetz wrote:
  

  I'm still working on the resumption of this problem that AxshunJaxun has been able to help me to diagnose properly.

  I have since received support from HP recovery and bought a new HARD drive that needs to be an improvement on the part of the plant. And I spent part of yesterday and most of the work now on the process of recovery without success (several failed attempts).

  I get a message "failed to retrieve" Application Recovery Manager with the message of the specific details of:

  [2:37:49.82] ChkErrBB.CMD: detect an error in the PININST_BBV.
  [2:37:49.82] ChkErrBB.CMD: check c:\system.sav\logs\BurnBootWarn.log
  [2:37:49.82] ChkErrBB.CMD: or, visit c:\system.sav\logs\BurnBootMerge.log

  (The two. LOG files do not exist on the C: partition, which is here.)

  I followed the process (initially had to hit ESC instead of F2) developed by anthony82 and met no error on drive testing HARD and memory.

  According to this message , it's probably a problem with the HP recovery media. anyone else seen this kind of problem and that this is the case also determined?

  http://h30434.www3.HP.com/T5/notebook-recovery/dv4-ChkErrBB-cmd-detect-some-error-during-PININST-BBV/TD-p/1314599

  "Here's how fix you it. When you start your computer, press F10 which will lead you to the Manager of the BIOS. then press F9 to set the BIOS factory default save and exit, then perform a recovery.  Worked for me and it took me 3 weeks to understand lol. »

• OR PCI-6542: Creation of dynamic waveforms using the HSDIO library

  Hello!

  I have problems to understand how to create waveforms using the HSDIO library to run on a card PCI-6542. I need to create a program that activates a channel for 12.5 microseconds, waiting for a while (i.e. 100 samples) and activates another channel to 12.5 microseconds.

  This program must be used in a Multielement ultrasound system.

  Here the example of dynamic generation program that transforms the channels 0-2 on 1024 samples.

  /************************************************************************
  
  *
  
  *  Example program:
  
  *    DynamicGeneration.c
  
  *
  
  *  Description:
  
  *    Generates a simple model on the specified channel.
  
  *
  
  *  Pin connection information:
  
  *    None.
  
  *
  
  ************************************************************************/
  
  / * Includes * /.
  
  
  
  
  
  #include "niHSDIO.h".
  
  / * Sets * /.
  
  #define WAVEFORM_SIZE 1024
  int main (void)
  
  {
  
     ViRsrc deviceID = 'Dev1 ';
  
     ViConstString channelList = "0-2";
  
     ViReal64 sampleClockRate = 50.0e6;
  
     DataWidth ViInt32 = 4;
  ViUInt32 waveformDataU32 [WAVEFORM_SIZE];
  
     ViConstString waveformName = "myWfm";
  
     ViInt32 timeout = 10000; / * milliseconds * /.
  ViSession vi = VI_NULL;
  
     Error ViStatus = VI_SUCCESS;
  
     Bruno errDesc [1024];
  
     ViInt32 i;
  / * Initialize generation session * /.
  
     checkErr (niHSDIO_InitGenerationSession)
  
              Deviceid, VI_FALSE, VI_FALSE, VI_NULL, &vi));
  / * Assign channels for dynamic generation * /.
  
     checkErr (niHSDIO_AssignDynamicChannels (vi, channelList));
  / * Set up the clock sample parameters * /.
  
     checkErr (niHSDIO_ConfigureSampleClock)
  
              VI, NIHSDIO_VAL_ON_BOARD_CLOCK_STR, sampleClockRate));
  / * Query the data Width attribute * /.
  
     checkErr (niHSDIO_GetAttributeViInt32)
  
              VI, VI_NULL, NIHSDIO_ATTR_DATA_WIDTH, & dataWidth));
  
  
  
     / * Fill the waveform with ramp data * /.
  
     < waveform_size;="">
  
     {
  
  	   waveformDataU32 [i] = i;
  
     }
  checkErr (niHSDIO_WriteNamedWaveformU32)
  
              VI, waveformName, WAVEFORM_SIZE, waveformDataU32));
  / * Start the generation * /.
  
     checkErr (niHSDIO_Initiate (vi));
  / * Wait for all the generation * /.
  
     checkErr (niHSDIO_WaitUntilDone (vi, timeout));
  Error:
  If (error is VI_SUCCESS)
  
     {
  
        / * Print result * /.
  
        printf ("made without error. \n") ;
  
     }
  
     on the other
  
     {
  
        / * Get the description of the error and print * /.
  
        niHSDIO_GetError (vi, & error, sizeof (errDesc) /sizeof (petitioner), errDesc);
  printf ("\nError encountered\n===\n%s\n", errDesc);
  
     }
  / * log * /.
  
     niHSDIO_close (vi);
  / * prompt to go out (for the popup console windows) * /.
  
     to continue...\n");
  
     GetChar ();
  
  error return;
  
  }

  Issues related to the:

  How can I change the values in waveformDataU32 to create market reports (instead of just always on)?

  How to select the channel waveformDataU32 is applied to the?

  Thank you!

  Zachary Geier

  The waveformDataU32 table is an array of 32-bit integers. Each bit corresponds to a line on the device.  On the first clock cycle, this program outputs:

  0000 0000 0000 0000 0000 0000 0000 0000

  Then it displays the following, changing at each clock Pulse:

  0000 0000 0000 0000 0000 0000 0000 0001,

  0000 0000 0000 0000 0000 0000 0000 0010,

  ...

  and so on all the way up to 1023:

  0000 0000 0000 0000 00000011 1111 1111

  In the example that you include at the bottom, you set the least significant bit (LSB) to zero and one, actually only change one line on the output. To change all the lines, you must instead use 4 294 967 295 or 0xFFFFFFFF:

  < waveform_size;="">
  
       < 200){="" if="" sample="" number="" is="" less="" than="">
  
            waveformDataU32 [i] = 0;     Disable channels 0-2
  
       }
  
       else {}
  
            waveformDataU32 [i] = 4 294 967 295;     Otherwise turn on all channels to 800 samples
  
       }
  
   }

• I use an analog input on a PCI-6224 and are having problems with the clock source

  I use an analog input on a PCI-6224 and are having problems with the clock source. I'm trying samples of 16 different analog inputs very quickly. I have the sample mode: Timed Single Point material. The rate, that I am running is the maximum (250 kHz (15625Hz per channel)). I left the default clock source and trying to taste several times. The analogue input works for a short time (2-3 seconds) and then everything stops. I'm doing something wrong or is there something I'm missing? Any advice would be great.

  That's how you samples using the sample clock clock. If you see a delay then something is wrong with how you track/data visualization.

  Single point NI the hardware is for PID control with a real-time operating system.

• The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1

  Intermittent crashes. The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1. How can I find this device? This is probably a hardware problem?

  I look at intermittent crashes, where my cursor becomes an hourglass and the system does not yet meet the ctrl-alt-delete.  In the case of a newspaper, I find

  Event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1.

  How can I determine which physical devices this is associated?  This indicates a hardware problem, or driver or firmware may be the source? The system has worked very well for a few years.  I'm not aware of any change in software that took place recently, although I have had by force, remove and reinstall iTunes earlier.

  I run SMART on all players controls and run diagnostics.  I ran chkdsk on the one I found the culprit, but not mistakes.

  Just in case it was a deadlock linked to memory, I tried to use the Diagnostics memory Microsoft on floppy, but it would not write on the disk (even if I could format and copy the files freely).

  Hello

  Go to your configuration and see which drive is for each port; 1,2,3,4...

  Then go to the Device Manager and look at how many SATA controller you have and how many ports for each, then start count from 0 to IdePort0, 1, 2, etc. for each SATA controller, so if you have 4 ports for each SATA controller, here is how you came from:

  IdePort0 1 -, 2 - IdePort1, 3 car - IdePort2 and road 4 - IdePort3 in the order of road by car

  I hope it helps

• Windows Media Center cannot detect the error DVD Windows Media Center cannot detect a DVD in the DVD - ROM drive. Insert a video DVD into the drive

  Original title: why Windows Media Center does not detect my DVD?

  I built my computer motherboard ASUS P658D, Intel i7 processor clocked at 2.6 gHz, 12 GB RAM, 750W Corsair PWR. power, Windows 7 Home Premium 64 - bit & ie9. When I put or the other two DVDs in one of two DVD players, Windows Media Center appears and when I click on "Play DVD" Media Center give me a window that says:

  "Windows Media Center cannot detect a DVD in the DVD - ROM drive. Insert a video DVD in the drive." Two DVDs, I've tried are educational for DVD

  my Nikon D300 Digital camera and a family video DVD or both these very well play in a bed of same computer running Windows 7 Professional 64-bit, & ie8.

  I tried Microsoft Fixit, no help. I tried to send Microsoft Support, and I got NO HELP. I did not bring any changes, and installed any program, just

  scoured the internet. A DVD player is a Sony Optarc with Microsoft Driver, the other is ASUS. I also tried to use Windows Media Player but nothing

  rises or it returns me to Windows Media Center and it does not detect to play either of my DVD. How can I get help here, or from Microsoft? Thank you.

  No, there is no yellow warning in Device Manager and the device manager says that two DVD players work properly. Mr. Fix it's

  automated download from microsoft that is supposed to automatically fix some problems, but he provided no help here. I think it is more likely

  that there is a problem with Windows Media Center or Windows 7 Pro 64 bit and either of my two new Sony DVD drives

  and ASUS.

  I thought my way in a solution. My thought was: Device Manager indicates DVD players work properly and both are new and we're Sony, and the other ASUS so I think only an unlikely problem with readers. The problem is with Windows Media Center "do DETECTED is not the DVD. So there must be a problem with Windows Media Center. I thought that I might need to reinstall Windows 7... then I thought that maybe if I just reinstall Windows Media that will work. He did. My problem was:

  Start > Panel > programs and features > features on or off Windows activate > then uncheck the box for multimedia functions > restart the computer > and then re-check the box to restore the multimedia features > now both discs play both DVDs, I tried. Both disks are operating normally. Reinstall the characteristics of media Windows 7 resolved the problem. Thanks to all who offered solutions.

• My Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1

  My computer (W7/64) sometimes fall to restart. I checked HD and the memory of Mrs. rescue disk - no error.
  Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1.
  The fact is that the cd-rom drive is behaving oddly. Reads the DVD of film without problem, but does not read floppy disks to install Windows (good on an another two comps).
  I therefore launched Verifier.exe and checked the other drivers. The result is dumpATA.sys is not running. (Is BTW not MS driver?).
  How can I force to load this driver?

  I checked the installation disc to compare the original version, boot.win opened, but the pilot is nowhere. Where did it come from?
  So I recorded the dump file, but the analysis of what this file is beyond my capabilities.
  Link to my file https://skydrive.live.com/redir?resid=4AF01405E5CE0354 dump! 114

  You could any body help me to find the source of my problem?

  Thank you.

  These are all good things:

  *****************************************************************************
  * *
  * Bugcheck analysis *.
  * *
  *****************************************************************************

  KERNEL_DATA_INPAGE_ERROR (7A)
  The requested page of kernel data could not be read in.  Usually caused by
  a bad block in the disk controller or paging file error. See also
  KERNEL_STACK_INPAGE_ERROR.
  If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
  This means that the disk subsystem has suffered a failure.
  If the status of the error is 0xC000009A, it means the query failed because
  a file system has failed to move forward.
  Arguments:
  Arg1: 0000000000000020, type of lock which took place (1,2,3 or PTE address value)
  Arg2: ffffffffc000009d, error state (state code of e/s normally)
  Arg3: fffffa80077f95b8, the current process (virtual address for the lock type 3 or PTE)
  Arg4: 0000000000000000, virtual address that could not be paged in (or the contents of the PTEs if arg1 is a PTE address)

  Debugging information:
  ------------------
  ERROR_CODE: (NTSTATUS) 0XC000009D - STATUS_DEVICE_NOT_CONNECTED
  DISK_HARDWARE_ERROR: Error occurred with disc material
  BUGCHECK_STR: 0x7a_c000009d
  CUSTOMER_CRASH_COUNT: 1
  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
  Nom_processus: System
  CURRENT_IRQL: 1
  LAST_CONTROL_TRANSFER: from fffff80002c7fcac to fffff80002c8bc00
  STACK_TEXT:
  fffff880 '03578-88 fffff800' 02c7fcac: 00000000' 0000007 a 00000000'00000020 ffffffff 'c000009d fffffa80' 077f95b8: nt! KeBugCheckEx
  fffff880 '03578-90 fffff800' 02c74ba7: fffffa80 '077f9550 00000000' c000009d 00000000 00000000' fffffa80' 077f95e8: nt! : FNODOBFM: 'chain' + 0 x 50080
  fffff880 '03578b 50 fffff800' 02c7e617: fffffa80 ' 07654b 50 fffffa80 '07654ba0 fffffa80' 077f9550 fffffa80 ' 077f95b8: nt! IopCompletePageWrite + 0 x 57
  fffff880 '03578b 80 fffff800' 02c8181d: fffffa80' 07654b 50 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiDeliverApc + 0x1c7
  "fffff880 ' 03578 c 00 fffff800 ' 02c4e4fb: 00000000 00000010' fffff800 '00b 96080 00000000 00000000' fffff800' 02c229a0: nt! KiCommitThreadWait + 0x3dd
  "fffff880 ' 03578 c 90 fffff800 ' 02c229fa: fffffa80 '07654b 50 00000000 00000001' fffffa80' 069ed040 00000000' 00000000: nt! KeWaitForGate + 0xfb
  fffff880 '03578ce0 fffff800' 02f29ede: fffffa80' 07654b 50 00000000'00000000 00000000'00000080 00000000'00000001: nt! MiModifiedPageWriter + 0x5a
  "fffff880 ' 03578 d 40 fffff800 ' 02c7c906: fffff800'02e06e80 fffffa80 '07654b 50 fffff800' 02e14cc0 00000000' 00000000: nt! PspSystemThreadStartup + 0x5a
  "fffff880'03578 d 80 00000000 00000000': fffff880'03579000 fffff880 ' 03573000 fffff880 ' 03578a 80 00000000 00000000': nt! KxStartSystemThread + 0x16
  STACK_COMMAND: kb

  FOLLOWUP_IP:
  NT! : FNODOBFM: 'chain' + 50080
  fffff800'02c7fcac cc int 3
  SYMBOL_STACK_INDEX: 1
  SYMBOL_NAME: nt! : FNODOBFM: 'chain' + 50080
  FOLLOWUP_NAME: MachineOwner
  MODULE_NAME: nt
  Nom_image: ntkrnlmp.exe
  DEBUG_FLR_IMAGE_TIMESTAMP: 5147d9c6
  FAILURE_BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080
  BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080

  And this page explains what you have:
  http://msdn.Microsoft.com/en-us/library/Windows/Hardware/ff559211 (v = vs. 85) .aspx >
  (Short version of an argument 9 d: "0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective wiring or in bulk, termination or that the controller does not see the hard drive.")

  It seems to intimate that it's a hardware problem rather than a driver. You say that you are having problems with the optical drive. If you log out, you still have problems to restart or boot?

  This probably isn't a memory problem, but a better method of verification, it is with Memtest86 + http://www.memtest.org/#downiso>
  Download the ISO and then create a CD with it and boot from it. If you have more than one piece of RAM, pull all but one test, then close, replace it with another and test, etc. I find it a little faster than the test at a time.

  SC Tom

• How many ethernet modem ports should have to support the airport Time Capsule

  I have a question: how many ethernet ports if a modem must support the airport Time Capsule?

  One (1)

• In pictures: How to delete an Album or a project in the list?

  I have an iMac 27 "mid2011.  And OS X El Capitan.  In Photos ' how to delete an Album or a project in the list?

  Right-click on it, select Delete. It will be removed from your library, not only the sidebar 'list '.

• I would like to know how to prevent messages sent to be registered on the SMTP server

  Currently, my Thunderbird client saves a copy of all messages sent to the folder "sent", as expected. All sent messages are also stored on the Server SMTP (G-Mail in this case). To avoid having to delete them manually, I want to warn the outgoing message to be stored on the SMTP server in the first place. Currently, my account of Thunderbird for Copies and folders settings has a check mark next to the option 'Other' with a destination of the folder option sent in Thunderbird. I don't see any other parameters that could control how sent SMTP mail server handles. I use the POP service only with the G-Mail Server. What settings should be in place to prevent messages accumulate in the folder "sent" on the SMTP server account?

  I think I can now answer my own question! The question turns out to be a g-mail not delivered not a factor controlled by Thunderbird.

  Apparently g-mail can automatically a copy of all mail sent by SMTP service one account. It's a "feature" that cannot be disabled! A workaround seems to be to set up a filter in g-mail account settings for all mail with an address corresponding to your own email address and send the message to the trash folder. Items in the Recycle Bin are automatically deleted after 30 days. Google prevents the rule 30 days being modified by measure of security, but at least trashed messages for irrevocably removed in a month.