"Detect an error in the course of the PININST_BBV".

Similar Questions

• Error chkerrBB.cmd detects an error during the PININST_BBV. chkerrBB.cmd check c:\system.sav\logs\BurnBootWarn.log, unable to perform the system recovery

  Original title: Vista system recovery failure

  I have a HP dv4-1275mx laptop and I just replaced the hard drive.  I got the Vista hp HP system recovery disks but recovery has failed 3 times.  The hard drive is new and has more space than the old.  It is a Western Digital 640 GB scorpio blue sata 5400 RPM.

  Error message:
  chkerrBB.cmd [17:18:51.36] detect an error in the PININST_BBV.
  [17:18:51.37] chkerrBB.cmd check c:\system.sav\logs\BurnBootWarn.log

  Hello

  I would say to contact contact HP support to:

  HP customer service

  http://h10025.www1.HP.com/ewfrf/wc/siteHome?cc=us&LC=en

• Detect an error in the PININST_BBV. [SOLVED]

  I have a HP 2000-2b16NR that needed a new HARD drive. I ordered and just got the DVD recovery for this model of HP and after running 5 times the HP recovery, I get this error message.

  ChkErrBB.CMD: Detects an error in the PININST_BBV.
  ChkErrBB.CMD: Check c:\system.sav\logs\BurnBootWarn.log
  ChkErrBB.CMD: or, visit c:\system.sav\logs\BurnBootMerge.log

  I've already tried default BIOS as suggested in another thread for this type of error no joy.  I even pulled the CMOS battery and removed the hand Batt power as well.

  Search the HARD drive for these two burnbootwarn.log and BurnBootMerge.log log files and they do not exist in c:\system.sav\logs. However find it in BurnBootMergeBBV1.log there.

  Replacing the HARD drive is a HGST Travelstar H2IK500854SP 500 GB / 5400 RPM/MIN/8 MB Cache

  I suspect that the DVD is bad or HP recovery process is total cr@p!

  RESOLVED: seems the extra disk is bad.  Ran recovery jump the diskette extra and everything's fine.

  RESOLVED: seems the extra disk is bad.  Ran recovery jump the diskette extra and everything's fine.

• The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1

  Intermittent crashes. The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1. How can I find this device? This is probably a hardware problem?

  I look at intermittent crashes, where my cursor becomes an hourglass and the system does not yet meet the ctrl-alt-delete.  In the case of a newspaper, I find

  Event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1.

  How can I determine which physical devices this is associated?  This indicates a hardware problem, or driver or firmware may be the source? The system has worked very well for a few years.  I'm not aware of any change in software that took place recently, although I have had by force, remove and reinstall iTunes earlier.

  I run SMART on all players controls and run diagnostics.  I ran chkdsk on the one I found the culprit, but not mistakes.

  Just in case it was a deadlock linked to memory, I tried to use the Diagnostics memory Microsoft on floppy, but it would not write on the disk (even if I could format and copy the files freely).

  Hello

  Go to your configuration and see which drive is for each port; 1,2,3,4...

  Then go to the Device Manager and look at how many SATA controller you have and how many ports for each, then start count from 0 to IdePort0, 1, 2, etc. for each SATA controller, so if you have 4 ports for each SATA controller, here is how you came from:

  IdePort0 1 -, 2 - IdePort1, 3 car - IdePort2 and road 4 - IdePort3 in the order of road by car

  I hope it helps

• The driver has detected an error of the controller on \Device\Harddisk1\DR1. What is the cause?

  I get this message on 7 11 windows event log IDs ' driver has detected an error in the controller on \Device\Harddisk1\DR1. "" The message keeps poping up when ever I insert my usb memory key but the DR number changes when I swap beetwhen and other memory usm drives exmp usb ports. "The driver has detected an error of the controller on \Device\Harddisk1\DR3." otherwise, my system is runnig perfect.

  Hello

  Check the drive for errors and see if it works fine it after.
  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors
  The link above includes steps for the same.
   $C God will not look you over for medals, but for scars. Each winner has scars; I do this either on the same heart

• The driver has detected an error of the Comptroller on \Device\Ide\IdePort3

  Hello

  I'll try to explain my problem as best as possible in chronological order then please bear with me.

  I have Windows 7 x 64.
  So last week my PC have been freezing every two days. Sometimes every day. Black screen during the games, navigation or doing any activity. Each window has frozen, the screen went black. ctrl alt del did not work no response to any entry, the only option was to restart.

  Once restarted, the system would freeze again almost immediately, and again after another reboot. Only solution was physically turn off the computer, turn off the power and wait.  After some time (5-10 min) I turn the power on and system worked very well.

  I went to the observer of events and found "the pilot detected an error of the Comptroller on \Device\Ide\IdePort3." It took place in a series starting with a per minute, then after a few minutes, two or three that occur within one minute, the frequency of this error would be gradually go back even to 10 per minute and that's where the system would freeze.

  Looking at the event viewer I thought, hold for a second I have 3 discs (Disk0 - new SSD, Disk1 - new HDD, Disk2 - old HDD) so maybe that ideport3 refers to the CDROM which I disconnected but the error has not disappeared.

  Check the BIOS settings and deleted everything that had no boot from the internal storage (so: floppy USB - disk, CDROM,)-which did not help either.

  In the Act of desperation, I unplugged my old disk (Disk2) for 6 days I have not known of IdePort3 errors and system will work very well.

  After 6 days, to my embarrassment, error returned.
  This is the story of the appearance of the error:

  10/05/2015 19:56 - after that, I unplugged old hdd
  16/05/2015-09:35
  16/05/2015 14:34
  16/05/2015 14:34
  16/05/2015 14:34
  16/05/2015 14:34
  16/05/2015 14:35
  16/05/2015 14:36
  16/05/2015 14:36
  16/05/2015 14:37
  16/05/2015 14:37
  16/05/2015 14:37
  16/05/2015-17:28
  16/05/2015-17:29
  16/05/2015-17:31
  16/05/2015-17:33
  16/05/2015-17:33
  16/05/2015-17:34
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:37 - after this system error stopped

  Here are the details of the error

  -
  -
   
    11
    2
    0
    0 x 80000000000000
   
    107016
    System
    Odin
   
   
  -
    \Device\Ide\IdePort3
    0000100001000000000000000B0004C004000000850100C00000000000000000000000000000000001000000000000000000000005100000
   
   
   
   
  Let me know if you all the news and thank you for your time in reading my number.

  I bought the card mother-GA-Z68X-UD3-B3 3 years ago. There can be no IDE ports. It has 6 SATA ports.

  Here an explanation somewhat losely formulated to work on the port that could be the culprit. Since you have 6 SATA ports, why not play the game of elimination with them?

• My Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1

  My computer (W7/64) sometimes fall to restart. I checked HD and the memory of Mrs. rescue disk - no error.
  Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1.
  The fact is that the cd-rom drive is behaving oddly. Reads the DVD of film without problem, but does not read floppy disks to install Windows (good on an another two comps).
  I therefore launched Verifier.exe and checked the other drivers. The result is dumpATA.sys is not running. (Is BTW not MS driver?).
  How can I force to load this driver?

  I checked the installation disc to compare the original version, boot.win opened, but the pilot is nowhere. Where did it come from?
  So I recorded the dump file, but the analysis of what this file is beyond my capabilities.
  Link to my file https://skydrive.live.com/redir?resid=4AF01405E5CE0354 dump! 114

  You could any body help me to find the source of my problem?

  Thank you.

  These are all good things:

  *****************************************************************************
  * *
  * Bugcheck analysis *.
  * *
  *****************************************************************************

  KERNEL_DATA_INPAGE_ERROR (7A)
  The requested page of kernel data could not be read in.  Usually caused by
  a bad block in the disk controller or paging file error. See also
  KERNEL_STACK_INPAGE_ERROR.
  If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
  This means that the disk subsystem has suffered a failure.
  If the status of the error is 0xC000009A, it means the query failed because
  a file system has failed to move forward.
  Arguments:
  Arg1: 0000000000000020, type of lock which took place (1,2,3 or PTE address value)
  Arg2: ffffffffc000009d, error state (state code of e/s normally)
  Arg3: fffffa80077f95b8, the current process (virtual address for the lock type 3 or PTE)
  Arg4: 0000000000000000, virtual address that could not be paged in (or the contents of the PTEs if arg1 is a PTE address)

  Debugging information:
  ------------------
  ERROR_CODE: (NTSTATUS) 0XC000009D - STATUS_DEVICE_NOT_CONNECTED
  DISK_HARDWARE_ERROR: Error occurred with disc material
  BUGCHECK_STR: 0x7a_c000009d
  CUSTOMER_CRASH_COUNT: 1
  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
  Nom_processus: System
  CURRENT_IRQL: 1
  LAST_CONTROL_TRANSFER: from fffff80002c7fcac to fffff80002c8bc00
  STACK_TEXT:
  fffff880 '03578-88 fffff800' 02c7fcac: 00000000' 0000007 a 00000000'00000020 ffffffff 'c000009d fffffa80' 077f95b8: nt! KeBugCheckEx
  fffff880 '03578-90 fffff800' 02c74ba7: fffffa80 '077f9550 00000000' c000009d 00000000 00000000' fffffa80' 077f95e8: nt! : FNODOBFM: 'chain' + 0 x 50080
  fffff880 '03578b 50 fffff800' 02c7e617: fffffa80 ' 07654b 50 fffffa80 '07654ba0 fffffa80' 077f9550 fffffa80 ' 077f95b8: nt! IopCompletePageWrite + 0 x 57
  fffff880 '03578b 80 fffff800' 02c8181d: fffffa80' 07654b 50 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiDeliverApc + 0x1c7
  "fffff880 ' 03578 c 00 fffff800 ' 02c4e4fb: 00000000 00000010' fffff800 '00b 96080 00000000 00000000' fffff800' 02c229a0: nt! KiCommitThreadWait + 0x3dd
  "fffff880 ' 03578 c 90 fffff800 ' 02c229fa: fffffa80 '07654b 50 00000000 00000001' fffffa80' 069ed040 00000000' 00000000: nt! KeWaitForGate + 0xfb
  fffff880 '03578ce0 fffff800' 02f29ede: fffffa80' 07654b 50 00000000'00000000 00000000'00000080 00000000'00000001: nt! MiModifiedPageWriter + 0x5a
  "fffff880 ' 03578 d 40 fffff800 ' 02c7c906: fffff800'02e06e80 fffffa80 '07654b 50 fffff800' 02e14cc0 00000000' 00000000: nt! PspSystemThreadStartup + 0x5a
  "fffff880'03578 d 80 00000000 00000000': fffff880'03579000 fffff880 ' 03573000 fffff880 ' 03578a 80 00000000 00000000': nt! KxStartSystemThread + 0x16
  STACK_COMMAND: kb

  FOLLOWUP_IP:
  NT! : FNODOBFM: 'chain' + 50080
  fffff800'02c7fcac cc int 3
  SYMBOL_STACK_INDEX: 1
  SYMBOL_NAME: nt! : FNODOBFM: 'chain' + 50080
  FOLLOWUP_NAME: MachineOwner
  MODULE_NAME: nt
  Nom_image: ntkrnlmp.exe
  DEBUG_FLR_IMAGE_TIMESTAMP: 5147d9c6
  FAILURE_BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080
  BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080

  And this page explains what you have:
  http://msdn.Microsoft.com/en-us/library/Windows/Hardware/ff559211 (v = vs. 85) .aspx >
  (Short version of an argument 9 d: "0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective wiring or in bulk, termination or that the controller does not see the hard drive.")

  It seems to intimate that it's a hardware problem rather than a driver. You say that you are having problems with the optical drive. If you log out, you still have problems to restart or boot?

  This probably isn't a memory problem, but a better method of verification, it is with Memtest86 + http://www.memtest.org/#downiso>
  Download the ISO and then create a CD with it and boot from it. If you have more than one piece of RAM, pull all but one test, then close, replace it with another and test, etc. I find it a little faster than the test at a time.

  SC Tom

• EventID:11 - the pilot detected an error in the controller on \Device\Ide\IdePort4.

  I started getting the following error message:

  Log name: System

  Source: atapi

  Date: 16/03/2013 18:36:37

  Event ID: 11

  Task category: no

  Level: error

  Keywords: Classic

  User: n/a

  Computer: Sanja-PC

  Description:

  The driver has detected an error of the controller on \Device\Ide\IdePort4.

  The event XML:

   

     

      11

      2

      0

      0 x 80000000000000

     

      169902

      System

      Sanja-PC

     

   

   

      \Device\Ide\IdePort4

      0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000003000000000000000000000004100000

   
  The last time I had this error was for malware using ESET secruit security check. During which I got like 11 errors with event ID 11 in the observer diary of events. Next, I had warnings of ntfs with event ID: 57:
  Log name: System

  Source: Ntfs

  Date: 16/03/2013-17:24:11

  Event ID: 57

  Task category: (2)

  Level: WARNING

  Keywords: Classic

  User: n/a

  Computer: Sanja-PC

  Description:

  The system failed to flush the data in the transaction log. Corruption may occur.

  The event XML:

   

     

      57

      3

      2

      0 x 80000000000000

     

      169876

      System

      Sanja-PC

     

   

   

     

     

      0000000001000000020000003900048000000000850100C 000000000000000000000000000000000

   
  The system works fine, no freezes or crashes, but I would like to know what is the cause, is it hardware or driver related?

  Hello

  Thank you for contacting Microsoft Community.
  Since you don't face any problem while working, the system works very well. The error in the log occurred due to the error of the driver in this case. But immediately, Windows is taking measures to restore the driver, so that the system works very well. The journal entry is just a notification. During the scan, the higher the use of the disc, so the number of failures is likely to increase. It occurs even in situations where there is a transfer of files.

• Flex Builder detects more errors against the definition of the Array class.

  Hello

  I don't know if this is the right forum to post this problem, but here goes.

  I've been developing an application using Flex Builder 3. Today, I met a strange problem. When I use a table variable in an Actionscript class, the compiler detects more errors against the class definition. I have only encountur this behavior with the Array class. Other classes of higher level, seem to work. F.i. I can insert the following text in a function:

  var a: Array = [1, 2, 3];

  var i: a.Len;

  After construction, I get no error. When I run the application, the variable I is set to 0.

  I tried to clean up the existing project. I created a new project in flex from scratch. The problem remains.

  I did not have any updates lately, f.i. flash player, java,... the development environment has not changed as far as I know.

  Can someone give some advice about this problem? Thank you.

  Kind regards

  Wim.

  The table is a dynamic class, as an object, which means that it is perfeclty happy to return values for properties that have never put. These values will be "undefined", which, when converted to an integer, turn into 0. This is the kind of unfortunate behavior, but there is no way to get around.

• Driver has detected an error in the controller on \Device\CdRom0

  I have a laptop running Vista Home Premium 32 Bit.  The DVD - RW drive is not working after that the PC wakes up from sleep mode.  I get the following error.

  "The pilot detected an error on \Device\CdRom0 controller."
  Log name: System
  Source: cdrom
  Event ID: 11
  Level: error

  I already tried the MS-Fix-IT solution and MS Knlowledge base 314093 bolt torque and 154690 nothing helps.  I really saw all other posts with this same problem.  The drive to function properly when the PC starts first, but it runs just when I put in a disk after getting out of the mode standby.  The system also has stop some time when I try to reject the disc turns, but it eventually starts fine.

  I appreciate any help I can get with this problem.  Please let me know if I can provide more information.  Thank you!

  Hello

  1 do these to erase corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ------------------------------------------------

  2 try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This update the default driver stack and help clear corruption.

  ------------------------------------------------

  3 use these methods to solve the outstanding issues.

  Shoot sleep problems - hibernation
  http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

  How to solve a problem of Mode for Vista and find a Solution
  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
  http://support.Microsoft.com/kb/950686

  Panel configuration-Device Manager - look at the settings for the network card, WiFi, Modem power management.
  and other devices. (Double click on the device and the power management tab)

  All the default power plans and then set them as you wish.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• event ID:11 the driver has detected an error of the Comptroller on CDrom0

  Hi all

  DVD drive does not read or write

  the operating system is windows xp sp2.

  I checked for the hardware changes in Device Manager there is no...

  It was working fine a few days ago, but now it is not

  so I checked where the spectator, I had the id of the error above.

  Kindly help

  I don't know I'm missing something... kindly help

  Concerning

  Sudeep

  Hello

  • What were the changes made before the issue started?

  I suggest you to refer to this link:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060

• Event ID 11: the driver has detected an error in the controller on \Device\Harddisk2\DR11.

  My event log is loaded with these on a system just to receive Dell 15-Sep and I don't know why.

  Do not ask questions - yet.

  I would like to know how to solve this, please. Thank you!

  Hello

  Have you connected external hard drive to the computer?

  In almost all cases, these messages are due to hardware problems. The source can be the controller or (more probably) a (drive 2) device that is connected to the controller. The problem of equipment may be termination rate settings, bad wiring or incorrect transfer, a defective unit, or in rare cases, a bad device driver written.

  Run the troubleshooter.

  Troubleshooting Windows

  http://Windows.Microsoft.com/en-us/Windows7/troubleshooting-in-Windows

  You can also check this thread:
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/Windows-7-64bit-USB-problem/b9eb5cfe-0036-45ef-b7f0-36c973398f49

  As it is a new computer, I suggest you contact the manufacturer of the computer.

• Detect/catch errors for photos in datagrid

  Hi all

  Is that anyway to detect/catch errors for the loading of the photos in the grid data if pictures cannot be loaded for some reasons such as photo not found in the directory, etc... As the use of ioerror or sth...

  This is how I load photos in the datagrid control. Using

  var col_img:DataGridColumn = new DataGridColumn("photo");
                 myDataGridList.addColumn(col_img);
                 col_img.cellRenderer = LoaderCellRenderer;
                 col_img.width = 80;
                 col_img.sortOptions = Array.NUMERIC;
                 col_img.resizable = false;
                 col_img.headerText = "Photo";
                 LoaderCellRenderer._stage = this;
  

  //LoaderCellRenderer.as
  
  
  package {
  
       import fl.containers.UILoader;
       import flash.events.MouseEvent;
       import flash.display.Stage;
       import flash.ui.Mouse;
       import fl.controls.listClasses.ListData;
       import fl.controls.listClasses.ICellRenderer;
  
       public class LoaderCellRenderer extends UILoader implements ICellRenderer {
            protected var _data:Object;
            protected var _listData:ListData;
            protected var _selected:Boolean;
            public static var _stage;
  
            public function LoaderCellRenderer() {
                 super();
                 addEventListener(MouseEvent.CLICK, onClick);
                 addEventListener(MouseEvent.ROLL_OVER, rOver);
                 addEventListener(MouseEvent.ROLL_OUT, rOut);
            }
  
            private function onClick(MouseEvent):void {
                 if (! _stage.mainLoaderbg.mainLoader.visible) {
                      _stage.mainLoaderbg.mainLoader.source=_data.photo;
                      _stage.mainLoaderbg.visible=true;
                      _stage.mainLoaderbg.mainLoader.visible=true;
                      Mouse.cursor="button";
                 }
            }
  
            private function rOver(MouseEvent):void {
                 if (! _stage.mainLoaderbg.mainLoader.visible) {
                      Mouse.cursor="button";
                 }
            }
            private function rOut(MouseEvent):void {
                 Mouse.cursor="auto";
                 _stage.txt_statusList.text = ""; 
            }
  
            public function get data():Object {
                 return _data;
            }
  
            public function set data(value:Object):void {
                 _data=value;
                 source=value.photo;
            }
  
            public function get listData():ListData {
                 return _listData;
            }
  
            public function set listData(value:ListData):void {
                 _listData=value;
            }
  
            public function get selected():Boolean {
                 return _selected;
            }
  
            public function set selected(value:Boolean):void {
                 _selected=value;
            }
  
            public function setMouseState(state:String):void {
            }
  
       }
  }
  

  LoaderCellRenderer is a class written by the tutorial on the adobe site.

  Thank you

  Zainuu

  Use the below code to know if the image loaded has failed:

  In the .as file:

  Constructor
  public void LoaderCellRenderer()
  {
  Super();
       addEventListener (IOErrorEvent.IO_ERROR, ioErrorHandler);
  }

  private void ioErrorHandler(event:IOErrorEvent):void {}
  trace ("ioErrorHandler:" + event);
  trace ("Image URL Not Found");
  }

• ATAPI - event ID:11 - the pilot detected an error on \Device\Ide\IdePort0 controller.

  I'm getting following error in my event log Watcher:

  Log name: System
  Source: atapi
  Date: 2009-11-01 01:18:38
  Event ID: 11
  Task category: no
  Level: error
  Keywords: Classic
  User: n/a
  Computer: hendrim-PC
  Description:
  The driver has detected an error on \Device\Ide\IdePort0 controller.
  The event XML:
  
   
     
      11
      2
      0
      0 x 80000000000000
     
      53536
      System
      hendrim-PC
     
   
   
      \Device\Ide\IdePort0
      0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000
   
  

  Anyone any idea what is the cause?

  I replaced all the cables and hard drive but I get the same error (wasted money).

  When you start the PC and get "PIO MODE" in computer/manage/Device Manager / IDE ATAPI controllers ADA / ATA Chanel X/properties/Advanced is the cause, your PC is frozen.

  My "temporal" solution for this problem is:

  1 - Turn off the PC.

  2 - pick Up and the hard drive cable through the same port of the motherboard

  3. start the PC and the control in the advanced settings box-> "Ultra DMA Mode 6"; right now, you can work without problems.

  * If you can trade your motherboard (all under warranty) DO!

  -. - We are all waiting FOR you than get Microsoft a solution to force the departure to the top of "PIO MODE" to "ULTRA DMA 6"

• Windows Update has detected an error code 80200053 for the installation of the updates for the update of security for Microsoft Visual studio 2008 and 2010.

  Hello

  I received an update for security update for Microsoft Visual Studio 2010 (KB2542054) and the security update for Microsoft visual studio 2008 Service Pack 1 (KB 2538241). This updates have been detected by windows update on my laptop. However, when I tried to install these updates, they detect an error code 80200053, windows update encountered an unknown error. I need help with this ASAP. Thank you.

  Hello

  Step 1:

  You can read the following article and try to reset the Windows Update components and check.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Step 2:

  You can also check the links below and try to download and install the stand-alone package with updates:

  Microsoft Visual Studio 2010 RTM MFC security update

  Microsoft Visual Studio 2008 Service Pack 1 MFC security update

  Hope this information is useful.