How to access the Web-based utility?

Similar Questions

• Linksys spa3102, unable to connect to the web-based utility.

  I have a problem... try to configure my spa3102 voip router, I can't connect you to the basic utility web (192.168.0.1/admin/advanced) page that he asked me to in the installation guide.

  a reapears of error "404-File not found" every time.

  Help, please

  first of all, make sure that your computer is connected to the LAN port on the back of the SPA3102 - then, click Start > run > type cmd > click OK > type ipconfig > hit Enter - glance to the DEFAULT GATEWAY - use to access the web interface of the SPA3102

  ex. If the default gateway as 192.168.1.1 type http://192.168.1.1 in the address bar of your IE - you can then click admin on the upper right of the screen and then click on advanced, also on the upper right of the screen

  * Sometimes the IP address of SPa3102 changes to a different address, especially if the device when you connect the WAN port has the same IP address which is 192.168.0.1

• SX10 - how to access the web interface behind a firewall

  Howdy

  I have a very simple configuration, router and behind her SX10. I can't access the web interface of the remote unit. Is there a port that I need to activate or something?

  When the device was connected directly to the modem, with the public IP address, I was able to connect to the web interface.

  any suggestions here?

  I enter anything in the field AllowRemote.

  Thanks in advance!

  Web interface can be accessed using HTTP ether (80) or HTTPS (443).  To you how you want to deploy, but you can use NAT on the router, port forwarding, or even put the SX10 in DMZ on the router.

• WRT110-problem accessing the Web-based Setup Page

  I can't access the configuration page based on web for the WRT110 router I have. I am able to make a connection on two computers without the router, but when I add them I get an error message in my browser.

  I tried to access the configuration page based on the web both of my computers and some information were followed by Ecritel.net, but I'm having no luck. I receive the following error message "missed connection: connection to the server was reset while the page is loading." The network link was interrupted for negotiating a connection. Please try again. »

  Any advice would be greatly appreciated! Thank you!

  Actually, I get a different error message now. I made a few adjustments to things like the start menu, which is a problem before. Here is the new error message I received:

  Network timeout Server 192.168.1.1 takes too long to respond. The requested site did not respond to a connection request and the browser has stopped waiting for a response

  Can experience the high demand server or a temporary outage? Try again later.

  Are you unable to navigate to other sites? Check the computer's network connection.

  Is your computer or a network protected by a firewall or proxy? Incorrect settings can interfere with browsing the web.

  Still having trouble? See your network administrator or your Internet service provider for assistance.

  Someone at - it ideas? I searched on the Internet, but nothing I've tried works. Thank you in advance!

• I bought jointly, Priemer elements and Photoshop elements. I downloaded photoshop successfully. How to access the Web page download for elements of Prime Minister?

  I bought jointly, Priemer elements and Photoshop elements. I downloaded photoshop successfully. How can I get access to the

  Download the Web page for the elements of Prime Minister?

  Garyl21385743 what version of Premiere Elements you are wanting to download?  You can download the latest versions of Premiere Elements to products download Premiere Elements | 10, 11, 12, 13.  You can also find links to the installation files for most retail securities of Adobe Creative Software to to other downloads.

• How to access the web service from Oracle?

  Database version: Oracle Database 10g Enterprise Edition Release 10.2.0.3.0
  
  I'm making a call to a web service through a procedure/function...
  
  I tried to use
  

  CREATE OR REPLACE PROCEDURE Call_Rest_Webservice
  
   AS
  
    t_Http_Req Utl_Http.Req;
  
    t_Http_Resp Utl_Http.Resp;
  
    t_Request_Body VARCHAR2(30000);
  
    t_Respond VARCHAR2(30000);
  
    t_Start_Pos INTEGER := 1;
  
    t_Output VARCHAR2(2000);
  
  BEGIN
  
    /*Construct the information you want to send to the webservice.
    
    Normally this would be in a xml structure. But for a REST-
    
    webservice this is not mandatory. The webservice i needed to
    
    call excepts plain test.*/
  
    t_Request_Body := 'the data you want to send to the webservice';
  
    /*Telling Oracle where the webservice can be found, what kind of request is made
    
    and the version of the HTTP*/
  
    t_Http_Req := Utl_Http.Begin_Request('**webservice address**',
                                         'GET',
                                         'HTTP/1.1');
  
    /*In my case the webservice used authentication with a username an password
    
    that was provided to me. You can skip this line if it's a public webservice.*/
  
    --Utl_Http.Set_Authentication(t_Http_Req, 'username', 'password');
  
    /*Describe in the request-header what kind of data is send*/
  
    Utl_Http.Set_Header(t_Http_Req, 'Content-Type', 'text/xml charset=UTF-8');
  
    /*Describe in the request-header the lengt of the data*/
  
    Utl_Http.Set_Header(t_Http_Req, 'Content-Length', Length(t_Request_Body));
  
    /*Put the data in de body of the request*/
  
    Utl_Http.Write_Text(t_Http_Req, t_Request_Body);
  
    /*make the actual request to the webservice en catch the responce in a
    
    variable*/
  
    t_Http_Resp := Utl_Http.Get_Response(t_Http_Req);
  
    /*Read the body of the response, so you can find out if the information was
    
      received ok by the webservice.
    
      Go to the documentation of the webservice for what kind of responce you
    
      should expect. In my case it was:
    
      <responce>
    
        <status>ok</status>
    
      </responce>
    
    */
  
    Utl_Http.Read_Text(t_Http_Resp, t_Respond);
  
    /*Some closing?1 Releasing some memory, i think....*/
  
    Utl_Http.End_Response(t_Http_Resp);
  
  END;

  But it's me ORA-29272: HTTP request failed
  ORA-06512: at "SYS." UTL_HTTP", line 1029
  ORA-12545: Connect failed because target host or object does not exist
  
  But I can connect to the web server by going on * webservice address * through my browser.
  
  Is there an ACL must be open in order to have this capacity? I asked my s/n, but she asked me that I will need to give its name to username/password / ip in order to open an ACL...
  However there is no name to username/password required during a tour of the web service...
  
  Any help would be much appreciated...
  
  Thank you
  
  Published by: 986006 on March 4, 2013 08:38

  Y.L wrote:

  This is because the database could not connect to the specified server. Bad host name or IP address specified. Inability to resolve the hostname to an IP address. Firewall blocking. Etc.

  The host name, I put here can be visit through my browser. I think that it is not question of the host server... So, it could be a firewall on my side of the database which must be opened in order to visit the host?

  The "web browser" (your PL/SQL using UTL_HTTP code) code is running on the Oracle database server. He needs the same type of network access that has your browser on your PC. (firewalls open, authentication of the proxy if necessary, etc.).

  On 11g. Not on 10g.

  I saw the code example you post from the link you provided... those who only works on 11 g?
  If we can work on 10g, which package or what are the steps I need to follow in order to have that works on me?

  The code I posted works on both versions. My comment was regards the ACLs. No ACLs exist on 10g. If you only need to execute privs on the affected packages (e.g., UTL_HTTP, etc.).

  ACL were introduced with 11g - 11g, you also need the ADMINISTRATOR to create an ACL for you which will allow access to the UTL_HTTP network so now.

• Cannot access the web configuration utility - server wrote: level_15_access

  I've been using a Dlink router and wasn't getting any beach on my network, so I tried to configure my router linksys wrt150-n v1.1. I pressed the button reset for 20 seconds, then unplugged my modem (cable) and the router, then plugged in. When I open a browser window and type http://198.162.1.1, instead of open the configuration page, I get a message saying "the http://198.162.1.1:80 server requires a user name and password. "The server said: level_15_access.

  I left the empty user name and used the password default admin, and who does nothing.

  Tried to reset the router on 4 or 5 times without success. Any ideas on what I forget? I did not initially provided with the router Router installation CD, and it is not a downloadable file - I should be able to and have in the past been able to use the default IP address and the admin PW.

  Thank you!

  Try a Hard Reset:

  Hard Reset (aka 30/30/30 reset):

  The following procedure will clear the memory NVRAM and set dd - wrt return to default values:

  • With the power on, press and hold the reset button the back of the unit for 30 seconds
  • Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
  • Plug in the appliance ALWAYS keeping the reset button a final 30 seconds

• Workstation 9 - How to get the Web Interface

  As published in this thread: http://communities.vmware.com/message/2045995 but for VMW8, I can not access or find information in the manual on how to access the web interface of 'New' in VMW9?

  Any tips?

  Thank you!

  The WSX server for 9 Workstation is a separate download and install, see https://my.vmware.com/group/vmware/details?downloadGroup=WKST-900-WIN&productId=293&rPId=2920

  See also the configuration and usage WSX in VMware Workstation.

  -Andreas

• LaserJet p1102w: how to access the interface web printer with new router

  I just bought a new wireless router, hoping that I'll be able to more easily print with my p1102w.

  Internet access works ok desktop and laptop (wireless).

  However, I had bookmarked the IP address of my printer, and before, I've always been able to access it by clicking on the bookmark. I checked the range of IP addresses for the router, and the IP of the printer is outside this range, so I don't know why I am no longer able to access to this. I can't access the web interface, whether they come from my laptop or desktop (wired). However, the printer is capable of printing from the desktop without problem.

  How do I enter this? I would like to restart the configuration wireless configuration, but I thought I needed the web interface for this.

  I should just insert the CD? I made a tweak or two and would prefer to keep all the settings of the printer even if I can, but I can start all over again if I have to.

  
  HP LaserJet p1102w

  I just deleted the printer on my laptop computer, reset the settings of the printer default and then run Setup from the wired desktop wireless utility wireless. Seems to have worked, I can now access the web interface via my laptop now.

• How to access the interface web web services test

  I'm running my server 10.3 in test mode. How can I access the web test for my web service interface?
  I can see the wsdl, but I can't access the test interface as in previous versions.
  
  Thank you

  Click in the table of your Web Service deployment.

  Scroll down to the section modules and components. Here, you should see a tree that contains Web Services.

  Click your web service

  Click on the test tab

  Open the tree and here, you should see the link to test client.

  If you have the location of the WSDL file, you can also add: http://adminserverhostname:7001 / wls_utc /? wsdlUrl = forward, for example,

  http://adminserverhostname:7001/wls_utc/?wsdlUrl=http://serverhostname:port/CompanyWebService/CompanyService?WSDL
  

  in what http://serverhostname:port/CompanyWebService/CompanyService? WSDL is the location of the WSDL file

• Possible security for the Web-based Configuration

  My colleagues and I found something very interesting today... Despite having configured the FTP security settings (which have been confirmed to set up and in funcitoning. I can't open an FTP session to our remote target without specifying a username admin and the password) If you open the configuration tool based OR web in a browser, you can send via FTP to and from the target using the file remote browser without being connected to all! Everyone knows this?

  Apparently, these permissions are separate from FTP, but you can define these special permissions on the page of the security configuration for the web-based configuration utility.

• Any time I try to access the web site GOOGLE, this message 404 not found (nginx)

  Any time I try to access the web site GOOGLE, this message appears.

  Any suggestions as to what is the cause and what is the fix.

  Thank you

  Hi LindaPhillion,

  1. Did you the latest changes on the computer?
  2. What web browser do you use?
  3. Are you having similar issue with any other search engine?

  You will usually receive this error when Internet Explorer is able to connect to the website, but the webpage cannot be found. This error is sometimes caused because the webpage is temporarily unavailable or that the Web page has been removed.

  Get help with the Web site (HTTP error) error messages.

  http://Windows.Microsoft.com/en-us/Windows-Vista/get-help-with-website-error-messages-HTTP-errors

  Note: Above article also applies to Windows XP.

  Note: Try the step only if you are using the web browser Internet explorer below.

  Refer to the article below and try the steps mentioned, check if it helps.

  How to optimize Internet Explorer

  http://support.Microsoft.com/kb/936213/ro

• Internet Explorer will not access the web and my antivirus will not work. I have updated to ie 9 and ran the software programs software and spyware malware. My machine is running on vista.

  I have Norton AntiVirus by Comcast and it does not start because of a "connection problem". The only thing I could find wrong was the question would not access the web. I deleted a user account, a couple of days, but do not know if that would do anything.

  Hi IrishStew,

  You can see the article in order to analyze the logs of System File Checker.

  How to analyze the entries in the log file generating the program Checker (SFC.exe) resources of Microsoft Windows in Windows Vista

  http://support.Microsoft.com/kb/928228

  Since Internet Explorer works fine with mode safe mode with networking, you can perform the clean boot to see if a third-party service is causing this issue.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a troubleshooting follow step 7: reset the computer to start as usual

• How to access my Web site created through windows live?

  I created a Web site through windows live and to pay the Bill on windows live. I'm used to be able to connect to the website to make updates or changes when I signed into windows live, but now there is no option to do what I can find. How to access my Web site online for windows?

  Hello

  When you use Windows live and the question you have posted is related to Windows Live, so it would be better suited in the Windows Live community. Please visit the link below to find a community that will provide the best support.

  Windows Live Mail Forum

  http://www.windowslivehelp.com/forums.aspx?ProductID=15

• Limiting who can access the Web portal

  Is it possible that I can put a restriction that may and may not access the web portal. I work in a doctors office, I want doctors to be able to access their terminal server from home sessions, but I don't want the Office staff to have the opportunity to do so. Anyone know how I would go about setting up these restrictions? I am running Version 7.6

  Made two Applications to manage.

  Make two groups of ads, one for physicians and one for everyone else.

  Assign each group to another managed Application.

  Do target a device address for the subnet of the office IP range and this applies to the Application to handle for office staff.

  Now, when connecting doctors that they get their own icon to any place of the network they run and the office staff only get an icon in the network of the company.

  -Greg