How to block ping the ASA 5506 outside interface?
I configured a Cisco ASA VPN configuration and Setup. Everything works fine. The SAA outside interface is to pings (on the internet) which is a threat to security. How to only block ping to the external interface without interrupting the functions of the ASA. I tried what follows, but does not seem to work.
outside the IP = 169.215.243.X
ASA 2.0000 Version 2
Access list BLOCK_PING refuse icmp any host 169.251.243.X echo-reply
Access-group BLOCK_PING in interface outside
You have set up the ACL is only for traffic that gets sent through the ASA, ASA traffic is controlled in different ways. For ICMP, you can refuse the rattling of the SAA and that allows all other ICMP with the following configuration:
icmp deny any echo outsideicmp permit any outsideIt is also possible to ban all ICMP:
icmp deny any outsideThe 'truth' is probably somewhere between these two options. It's your choice.
Tags: Cisco Security
Similar Questions
-
How can I email the contact form outside of Business Catalyst?
I try to use the Muse and send the contact form, but not use Business Catalyst. Any suggestions?
Hello
You can use your online form, with all other hosts. Please click the link below to see how you can use the webform widget
Adobe help Muse | Work with the shape of Widgets
Let me know if you have any question.
-
How can I reinstall the Intel Management Engine Interface?
Hey there. I have a Lenovo Yoga 2 13, i5 and have some problems with the boot and sleep.
Startup problem: it takes 30 sec - 1 min at startup and display the Lenovo logo and the rotating circle
Pépin to sleep: the most of the time, if I close the lid for more than 20 seconds and open it again the screen starts flashing and then the computer shuts off.
So I tried the problem to resolve these issues, which lead me to the "Device Manager" where I have a past by each element and check for driver updates. Surprisingly, there were about 5-6 required. But the "Intel Management Engine Interface" did not work. The first time, it gave me an error and the second time (he had always the sign of error small triangle on yellow), he said that all the drivers are up to date. In my reading of the internet, some people were saying that the most recent update for this chipset was causing problems (ver.11) and that I should downgrade to version 9. So I uninstalled the driver, and then (I have a feeling that it was my mistake) also uninstalled the "Intel Management Engine Interface" how it disappeared from my list of 'Device Manager '. But when I tried to install the driver again for version 9 the error that appears is "this computer does not meet the minimum requirements for installing the software. Worm. 11 also gives me an error (even if I don't remember right now).
I have scowered the internets and found nothing even come close to answering that question. Any help appreciated.
As a side note, I also have some freezing problems when I plug in the power adapter, even if I think that maybe I should ask this question in another post...
J
Fixed. She appeared again in the device again Manager and I was able to do the downgrade. Don't know if I've seen a much improved...
-
Hi there please help me. I didn't have this problem until two days ago when the browser updated itself. I have the youtube video downloader add on and always use it. I'm on a data plan and it used to block videos and add ads which I like, but now is not because of the update, I came back to the old version, but it did not help and I downloaded the flash but block it does not work. It makes the slow loading of pages and uses a large amount of data that I tried many things like all the plugins of switching to add it on the menu to activate ever and it doesn't quite work. Before it used to show the gray screen, where it says "the flash player is out of date" on videos and commercials, but he does not do this because of the update so please help me to do it again.
I solved. On the firefox support page they will give you information about the HTML5 player and they say there that firefox uses it only 38 version before so I'm 36 version and it worked in blocking it as before.
So its all sort and if everyone wants to do the same thing go to https://ftp.mozilla.org/pub/firefox/releases/ and all previous versions will be there.
-
JDeveloper 12 c how to block created the user.
Hello, this is my first post. I have a question regarding my request - I use JDeveloper 12 c. In my application, I have implemented the user file, which has all the users who can connect to my request. For each user, I have an option called 'user locked '. I want to do that if the user is locked, it cannot log in to my application. Someone has an idea how I can do?
It is a code for my .java login:
public class LoginBean {}
private String _username;
private String _password;
public LoginBean() {}
LogEvents.addSyslog ("OPEN", "Connection...", null, null, null);
}
{} public void setUsername (String _username)
This ._username = _username;
}
public String getUsername() {}
return _username;
}
{} public void setPassword (String _password)
This ._password = _password;
}
public String getPassword() {}
return _password;
}
public String doLogin() {}
String _username =;
Byte [] pw = _password.getBytes ();
FacesContext ctx = FacesContext.getCurrentInstance ();
HttpServletRequest request = ctx.getExternalContext () .getRequest () (HttpServletRequest);
try {}
CallbackHandler Manager = new URLCallbackHandler (UN, pw);
MySubj subject = weblogic.security.services.Authentication.login (handler);
weblogic.servlet.security.ServletAuthentication.runAs (mySubj, request);
ServletAuthentication.generateNewSessionID (request);
String loginUrl = ' faces/welcome. '
LogEvents.addSyslog ("LOGIN. TRUE', 'Connected' - + this ._username, null, null, this ._username);
sendForward (loginUrl);
} catch (FailedLoginException fle) {}
ResourceBundle resourceBundle = BundleFactory.getBundle ("abc.view.ViewControllerBundle");
String msgTxt = null;
If (resourceBundle! = null) msgTxt = ("LOGIN resourceBundle.getString. NOT VALID");
If (msgTxt == null) msgTxt = "a bad user name or password was specified";
LogEvents.addSyslog ("LOGIN. (FALSE', 'Error while recording -' + this ._username, null, msgTxt, this ._username);
FacesMessage msg is new FacesMessage (FacesMessage.SEVERITY_ERROR, "Incorrect Username or Password", msgTxt);.
ctx.addMessage (null, msg);
setPassword (null);
} catch {} (the LoginException)
reportUnexpectedLoginError ("LoginException", the);
}
Returns a null value.
}
{} private void sendForward (String forwardUrl)
FacesContext ctx = FacesContext.getCurrentInstance ();
try {}
ctx.getExternalContext (.redirect (forwardUrl));
} catch (IOException ie) {}
reportUnexpectedLoginError ("IOException", IE);
}
ctx.responseComplete ();
}
' e private void reportUnexpectedLoginError (String errType, Exception) {}
ResourceBundle resourceBundle = BundleFactory.getBundle ("abc.view.ViewControllerBundle");
String msgTxt = null;
If (resourceBundle! = null) msgTxt = ("LOGIN resourceBundle.getString. OTHER') .concat ("(") .concat (errType) .concat ("") ");
If (msgTxt == null) msgTxt = "an unexpected error during the connection (".concat (errType).concat("), see the logs for details");
FacesMessage msg = new FacesMessage (FacesMessage.SEVERITY_ERROR, "Unexpected error during connection", msgTxt);
FacesContext.getCurrentInstance () .addMessage (null, msg);
FacesContext.getCurrentInstance () .renderResponse ();
}
}
Kind regards
WK
Hello
for that, you or the other
1 - write your own authentication provider in WLS that authenticates users, but also looks at the flag of "lock".
2 use the SQL authentication provider and modify the SQL query to include indicator
3 - in your code, check the user file before performing the authentication. At this point, you already have the user name. Just make sure that you don't tell people that their account is locked before you checked the authentication can be processed successfully. Otherwise - if you let them know right after comparing the lock check - your app can be used to exploit your underlying identity management system.
Frank
-
Lightroom is freezing after updated drivers AMD Catalyst and turn "use the graphics processor. Now I can not turn off in Lightroom, and I don't want to reset all preferences or downgrade my graphics drivers. Can someone tell me what channel in Lightroom 6 Preferences.agprefs is about using the GPU? Or is this another place?
To the incomparable help suggests the following line changes when the gpu is enabled / disabled (click on the image to enlarge).
I tried both ways, and it is only this value that switches. This isn't what I expect to be called however...
-
How can I get the vintage B3 organ interface screen
I just started with MainStage and wanted to play with the Vintage B3 organ. User guide instruments is an explanation how to use it, but not how to get there. This is probably very simple, but I can not find
See B3 Vintage of the input channel strip tab click the middle of it to open it.
-
How can I adjust the resolution of my interface?
Hey there,
I recently bought a new laptop (DELL Precision M3800 with screen 4K) and I have Photoshop configuration problems.
A few days ago I installed some CC-programs (Illlustrater, Indesign, Photoshop...). They all work very well, except Photoshop. The interface is way too small and I can't get it fixed. (Look at the pictures below) How can I get these things right? Thanks in advance!
Go in Edition > Preferences > experimental features and check the IU 200% scale.
-
Hello
5505 Cisco's internal IP: 10.10.0.1 static, securty level 100
External IP of Cisco 5505: 36.X.X.23 Dhcp, 0 security level
of within peut all host external example ping by host 10.10.0.3 to google.com
inside peut ping all domestic example of the host, host 10.10.0.3 to 10.10.0.5 included the internal IP of Cisco 10.10.0.1
inside peut ping ip network address different on the same network from my router external example the host 36.x.x.25
cannot ping inside the IP 36.X.X.23?
from outside peuvent ping the IP 36.X.X.23
outside peuvent ping different extenal network 36.X.X.X network ip
How can I ping the 36.X.X.23 of the Interior, any suggestions?It's called background management which is not supported in the ASA
https://Tools.Cisco.com/bugsearch/bug/CSCtd86651
That's why is not and this will never work the ASA design does not
It will be useful.
-
Allowing the VPN and return to the ASA 5520
Here is the configuration:
Outside Interface: 50.50.50.5
Internal interface: 192.168.1.5
Wireless interface: 192.168.2.5
The wireless interface is used for the guest access to internet and you can't find the internal servers or workstations. Offiste employees, we use Cisco VPN remotely in through the firewall.
That is the question, an itinerant person comes into the office, connects to the network (no LAN port available) wireless and then wants the VPN in a work. Can that be allowed through the ACL to allow traffic like that or would be using Cisco AnyConnect? I don't want to "overall" activate the ability for Wireless talk range to the inside interface, but allow VPN access. At first glance, I guess the ASA for not allowing this, but try to get some clarification, thank you!
And if it's possible, I can see security implications, so I'm also looking for information best practice as well.
Hello Mrjwilson,
5 stars for you
Thanks for sharing the solution, check now the question as answered so future users can learn of your problem.
-
Unable to load is the owner of standard Interface table at the Base of the OM tables
Hi gurus,
I load the data of shims for orders using the standard interface for order management.
I can see the data blocks in the table of standard interface
Select * from apps.oe_actions_iface_all;
gives me data from the pending requests that need to be attracted to the flat-rate import program.
but when I run the import of order program,
I get the following error
Order import concurrent program
Simultaneous program settings
Post only: N
Control the Source: 1064
Order code:
Sold to Org Id:
Sold to Org:
Change the sequence:
Performance parameter: Y
Cut the whites: N
Operation:
Number of Instances: 0
Debug level: 0
Request Id: 105961365
Org Id: 166
Cannot perform Action ask APPLY_HOLD
N ° of orders found: 1
N ° of orders imported: 1
N ° of the commands failed: 0
Message from the source/line/command/Seq
1064/12715682 / / 100, you are not allowed to apply this expectation.
End of the simultaneous programme of the Import command
Can someone help me on why it will fail in the import order program, which would be the cause of the simultaneous program error.
all input is much appreciated.
Thanks adavance
Published by: 909577 on August 24, 2012 12:01 AMHello
I have no English version (I don't want to open a session we language I'm lazy :)) This is my translation :) Order management responsibility-> Setup-> controls-> shims find you hold and look at authorization. Maybe your wrong because that pck.
Kind regards
Luko -
Using Captivate to record the user of Captivate interface
I want to Captivate allows you to create a Captivate demo video. How can I keep the user of Captivate interface to reduce when I start recording?
Mike
You can open several instances of Captivate and recording of one of them.
Anthony
-
My ASA cannot ping the lan address
I use ASA built ezvpn. I can access the ASA and ping inside port address successfully. But in my ping to the address of interconnection 10.100.255.2 window7 cant. I don't know how to solve the problem. If all goes well, can help me. Thank you...
set it up
ASA5520 # sh run
: Saved
:
ASA Version 7.2 (3)
!
asa5520-host name
sxng domain name
activate the encrypted password of DOAXe2w/ilkXwCIz
names of
DNS-guard
!
interface GigabitEthernet0/0
nameif outside
security-level 0
IP x.x.x.x 255.255.255.248
!
interface GigabitEthernet0/1
nameif inside
security-level 100
IP 10.100.255.254 255.255.255.0
!
interface GigabitEthernet0/2
nameif dmz
security-level 50
IP x.x.x.x 255.255.255.0
!
interface GigabitEthernet0/3
nameif wireless
security-level 10
IP x.x.x.x 255.255.255.0
!
interface Management0/0
Shutdown
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
management only
!
2KFQnbNIdI.2KYOU encrypted passwd
Disk0: / pix723.bin starting system
passive FTP mode
DNS server-group DefaultDNS
sxng domain name
dmz_access_in of access allowed any ip an extended list
dmz_access_in list extended access permit icmp any one
tunnel of splitting allowed access list standard 10.0.0.0 255.0.0.0
inside_nat0_outbound list of allowed ip extended access all 10.100.254.0 255.255.255.0
inside_nat0_outbound to access ip 10.0.0.0 scope list allow 255.0.0.0 10.100.254.0 255.255.255.0
outside_cryptomap_dyn_20 list of allowed ip extended access all 10.100.254.0 255.255.255.0
acl_out list extended access permit icmp any one
acl_out list extended access permit tcp any host x.x.x.x eq www
acl_out list extended access permit tcp any host x.x.x.x eq 9000
acl_out list extended access permit udp any host x.x.x.x eq 9000
........
......
acl_out allowed ip extended access list any 10.1.1.0 255.255.255.0
inside_access_in list extended access permitted tcp 10.1.10.0 255.255.255.0 any eq 5000
acl_inside of access allowed any ip an extended list
acl_inside list extended access permit icmp any one
wireless_access_in of access allowed any ip an extended list
wireless_access_in list extended access permit icmp any one
pager lines 24
Enable logging
timestamp of the record
emergency list vpn-event logging level
log message 109001-109028 vpn-event list
log message 113001-113019 vpn-event list
exploitation forest-size of the buffer 5000
information recording console
debug logging in buffered memory
recording of debug trap
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 dmz
MTU 1500 wireless
management of MTU 1500
IP local pool vpnpool 10.100.254.1 - 10.100.254.250 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ICMP allow any inside
ASDM image disk0: / asdm - 507.bin
don't allow no asdm history
ARP timeout 14400
Global (outside) 1 x.x.x.x
Global (dmz) 1 10.100.253.101 - 10.100.253.200 netmask 255.255.255.0
Global (wireless) 1 172.16.255.101 - 172.16.255.200 netmask 255.255.255.0
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 10.1.1.14 255.255.255.255
NAT (inside) 1 10.1.13.100 255.255.255.255
NAT (wireless) 1 172.16.0.0 255.255.0.0
static (dmz, outside) tcp x.x.x.x www 10.100.253.1 www netmask 255.255.255.255
.......
.........
static (inside, dmz) 10.1.1.11 10.1.1.11 netmask 255.255.255.255
static (inside, dmz) 10.1.1.16 10.1.1.16 netmask 255.255.255.255
static (dmz, external) 10.100.253.20 x.x.x.x 255.255.255.255 netmask
static (dmz, external) 10.100.253.32 x.x.x.x 255.255.255.255 netmask
Access-group acl_out in interface outside
acl_inside access to the interface inside group
Access-group interface inside acl_inside
Access-group dmz_access_in in dmz interface
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
Route inside 10.0.0.0 255.0.0.0 10.100.255.1 1
Route inside 10.0.0.0 255.0.0.0 10.100.255.2 1
Route wireless 172.16.0.0 255.255.0.0 172.16.255.1 1
!
router ospf 1
255.255.255.255 network 10.67.180.0 area 0
network 0.0.0.0 0.0.0.0 area 1
Journal-adj-changes
!
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.1.0 255.255.255.0 management
http 10.0.0.0 255.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
Crypto outside-dyn-map Dynamics-plan 20 reverse-drive value
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 20
Telnet 0.0.0.0 0.0.0.0 outdoors
Telnet 10.0.0.0 255.0.0.0 inside
Telnet 10.100.0.0 255.255.0.0 inside
Telnet 10.100.255.0 255.255.255.0 inside
Telnet 0.0.0.0 0.0.0.0 wireless
Telnet timeout 10
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 30
Console timeout 0
dhcpd x.x.x.x dns
!
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
!
class-map inspection_default
match default-inspection-traffic
!
!
Policy-map global_policy
class inspection_default
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
internal sxnggroup group policy
attributes of the strategy of group sxnggroup
value of server DNS 202.99.192.68
enable IP-comp
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
username password sxtrq Y6cwK1wOhbhJ6YI / encrypted
maboai R6eu6P1iKIwFIFjS username encrypted password
winet FwZ0ghxvIpXOepvf username encrypted password
tunnel-group sxnggroup type ipsec-ra
tunnel-group sxnggroup General-attributes
address vpnpool pool
Group Policy - by default-sxnggroup
sxnggroup group of tunnel ipsec-attributes
pre-shared-key *.
context of prompt hostname
Cryptochecksum:119ae137eef5ed97d38b4e2f90ed46d7
: end
ASA5520 # route sh
Code: C - connected, S - static, RIP, M - mobile - IGRP, R - I, B - BGP
D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone
N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2
E1 - OSPF external type 1, E2 - external OSPF of type 2, E - EGP
i - IS - L1 - IS - IS level 1, L2 - IS - IS IS level 2, AI - IS inter zone
* - candidate by default, U - static route by user, o - ODR
P periodical downloaded static route
Gateway of last resort is 202.97.158.177 to network 0.0.0.0
C x.x.x.x 255.255.255.248 is directly connected to the outside of the
C 172.16.255.0 255.255.255.0 is directly connected, wireless
S 172.16.0.0 255.255.0.0 [1/0] via 172.16.255.1, wireless
S 10.0.0.0 255.0.0.0 [1/0] via 10.100.255.1, inside
[1/0] via 10.100.255.2, inside
C 10.100.255.0 255.255.255.0 is directly connected to the inside
S 10.100.254.2 255.255.255.255 [1/0] via x.x.x.x, outdoor
C 10.100.253.0 255.255.255.0 is directly connected, dmz
S * 0.0.0.0 0.0.0.0 [1/0] via x.x.x.x, outdoor
ASA5520 # sh arp
outside 00d0.d0c6.9181 x.x.x.x
outside 00d0.d0c6.9181 x.x.x.x
outside 224.0.0.5 0100.5e00.0005
inside 224.0.0.5 0100.5e00.0005
inside the 10.100.255.1 0000.0c07.acff
inside the 10.100.255.2 001c.b0cb.5ec0
DMZ 10.100.253.20 60a4.4c23.3032
DMZ 224.0.0.5 0100.5e00.0005
DMZ 10.100.253.1 001a.6436.6df6
224.0.0.5 wireless 0100.5e00.0005
Wireless 172.16.255.1 0026.98c6.41c8
Try to use the "crypto ipsec to show his ' command to watch the program and decaps packages, I hope this isn't too fast increment. You should be able to see the two increase when you successfully and only one side increase when it fails. Check both sides of the vpn, and this should give you an idea where the problem is. If the program packages are multiplying on the ASA local to your PC Win7 and Decaps multiply on the ASA Remote and the program is not so, then the question is with packets from the remote side. I hope this will help you determine the location of the problem and then you can focus your search here.
-
How can I stop high disk activity HARD and blocking of the machine
At startup, the machine takes 2 to 3 minutes before the login screen is available, with HDD coming out of the machine all the time. The Office takes 1.5 minutes to load up. Then quite randomly and especially if I have access to Internet, the HARD drive starts screaming from afar and I get any program I use, indicate "not responding". Similarly, logging on Internet and then check in a site and outside, Yahoo shows "not responding" then comes good, however at that time that the HARD drive is once more trying to get out of the machine with the blocking of the entire system. This condition may last between 1 and 2 hours.
I can't get out of the Internet or Vista and my only recourse is to hold down the button "power on" for 5 seconds, stop the machine. The alternative is to turn the machine on and leave it alone for a few hours, but it is still not guaranteed the high activity of the HARD drive will be start at random. At the time of blocking, the CPU is variable between 1 and 10% with 4 GB of ram running at 96% to 100%.
I am running Windows Vista Home Premium (SP2), on an AMD Athlon (TM) 64 x 2 processor Dual core 5000 + 2.60 GHz, Medion machine with 4.0 GB Ram and 32-bit operating system. The machine is a PC MT7 MED MT469G. The boot drive (C: /) is about 350 GB, with a second backup drive (D: /) about 100 GB and a Data partition (E: /) drive on 400 Gb. I.e. two 350 and 500 GB drives.
The machine becomes practically unusable and I can't stop this frenzied action of HARD drive. I have to be to destroy the HARD drive whenever I turn on. I tried the advice from the experts by disabling regular departures, stopping at various folders, to nothing does not.
I came through all products Windows 95Windows with XP and 2000 and when I bought this computer Medion, with Vista, I have never experience so much time lost to fight with a machine with this huge HARD drive activity and constant locking machine.
I understand, sites that Windows 7 is pretty much the same, God forbid, I will put on my wife's machine and is the reason why I have not upgraded.
Help! Please, how can I get out of this mess?
Concerning
John Mills
I'm not sure I understand your disk configuration. You have two physical drives with drive non-system, divided into two partitions?
All other programs are running when this happens outside of the browser?
I would start by Process Explorer to identify the process generating the IO.
http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653
On the file menu, click 'Show details for all processes', and then on the view menu, select the columns to activity e/s of the shoe.
While you are in the view menu, click on "System information" and check how your 4 GB 32-bit Vista can see. It is normally about 3 GB but can be much less with some video cards.
There is more information on the use of Process Explorer here:
You can also use the built in by typing perfmon performance monitor in the box "Search" in the Start Menu.
http://Channel9.msdn.com/events/TechEd/Australia/Tech-Ed-Australia-2011/SVR306
This should help you identify files that are used.
For a more detailed study, you must use Windows Performance Toolkit:
http://msdn.Microsoft.com/en-us/performance/cc825801
http://Channel9.msdn.com/events/build/BUILD2011/HW-59T
Download here: http://www.microsoft.com/downloads/dlx/en-us/listdetailsview.aspx?FamilyID=6b6c21d2-2006-4afa-9702-529fa782d63b and select the components you need.
There is a possibility of a hardware problem or the disc is not not in AHCI mode.
I would also look at the antivirus you are using.
-
How can I get the engine working in the ASA 5505 Crypto
I bought a brand new ASA 5505 to connect to the Cisco 3640 and I can not yet set up the tunnel. I have tried to change the set of transformation to just but know luck. I recently put a VPN using DMVPN and Cisco 501 in a site-to-site, but it has been wondering what happens.
The router (3640 executes code 12.4) seems ok and I don't think I have a problem with the router with Cisco 501 great work.
This is a laboratory environment.
This is the function defined on the ASA 5505
The devices allowed for this platform:
The maximum physical Interfaces: 8
VLAN: 3, restricted DMZ
Internal guests: 10
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Peer VPN: 10
WebVPN peers: 2
Double ISP: disabled
Junction ports VLAN: 0
AnyConnect for Mobile: disabled
AnyConnect for Linksys phone: disabled
Assessment of Advanced endpoint: disabled
This platform includes a basic license.
This is a ping from 10.3.4.10 to 10.1.1.1. He said nothing about IPSEC or ISAKMP.
That's what I get when I do the: show crypto ipsec his
ASA5505 (config) # show crypto ipsec his
There is no ipsec security associations
ASA5505 (config) # show crypto isakmp his
There is no isakmp sas
Debug crypto isakmp 10
entry packets within the icmp 10.3.4.10 8 0 10.1.1.1 detail
I have worked on it for a week and don't really know if I have a bad ASA5505. Since the normal stuff like browsing the Internet works and I can ping to the outside and inside, I don't know what to think. See attachments.
"Do what you asked has worked.
Nice to hear that your problem is solved.
"My question is can I use the transform-set ESP-3DES-SHA instead of MD5?"
Of course you can.
Kind regards.
Please do not forget to note the useful messages and check "Solved my problem", if the post has solved your problem.
Maybe you are looking for
-
Hi my icloud address * @icloud.com is blocked. I write a lot of e letter in support of the team, but no one answer me. It is difficult answer for me? Apple support team does not? Where is our client's rights? Why can't anyone answer for me? I send on
-
Satellite L300-1AS does not load
Hello My laptop has stopped to load the other day, it should Flash it then recharges after that I have nothing! I tried pushing it with a little force it should blink. But now, nothing happens. It's very frustrating. The power supply had been pressed
-
When I go to HP & website support download drivers, it shows this long list of updates. Does only show the updates that I need like Windows updates or it shows all updates driver for my computer even though I have them already? I had HP updated activ
-
How can I turn off the laptop after restoring it to factory settings?
Hello everyone I'm selling my Portege R830-10 q If I want to restore it to the settings to factory (out-of-box state) AND THEN TURN IT OFF. I brought the laptop to factory settings successfully using the _TOSHIBA recovery Wizard_ and choosing * facto
-
Browser is redirected to site deemed dangerous. How can I stop this from happening?
Tried all removal tools through Microsoft Security essentials scans and also bought the PC health software. Occurrences have been reduced, but when I'm online my browser sometimes is always directed to "i.w55c.net/ping_match.gif" [[previously was al