Similar Questions

• ASA 5520 VPN licenses

  Community support,

  I want to run this question by you guys to avoid the sales of our partner CISCO and similar pitch more to the best solution that would give us what we want.

  We currently have a VPN from CISCO 3020 hub to terminate the Lan-to-Lan tunnels and have our mobile workers to connect through the client VPN CISCO (300 users-employees and contractors).

  Given that this device is coming to an end of LIFE this year, we bought a CISCO 5520 (here is the current licenses in this topic)

  Licensing seems quite complicated, so here's my question:

  -What VPN do you recommend for our users and entrepreneurs? I understand that the CISCO VPN client does not work with ASA 5500 Series devices

  Is there a license needed to deploy a VPN solution for our remote users(employees/contractors)?

  Thank you

  John

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited perpetual
  VLAN maximum: 150 perpetual
  Guests of the Interior: perpetual unlimited
  Failover: Active/active perpetual
  VPN - A: enabled perpetual
  VPN-3DES-AES: activated perpetual
  Security contexts: 2 perpetual
  GTP/GPRS: Disabled perpetual
  AnyConnect Premium peers: 2 perpetual
  AnyConnect Essentials: Disabled perpetual
  Counterparts in other VPNS: 750 perpetual
  Total VPN counterparts: 750 perpetual
  Shared license: disabled perpetual
  AnyConnect for Mobile: disabled perpetual
  AnyConnect Cisco VPN phone: disabled perpetual
  Assessment of Advanced endpoint: disabled perpetual
  Proxy UC phone sessions: 2 perpetual
  Proxy total UC sessions: 2 perpetual
  Botnet traffic filter: disabled perpetual
  Intercompany Media Engine: Disabled perpetual

  This platform includes an ASA 5520 VPN Plus license.

  Your understanding that the Cisco VPN client does not work with ASA is wrong. Maybe it's the version of Cisco VPN client that you use currently does not work with ASA. But these (and so not very new indeed) versions of VPN client work with the ASA. I installed for several clients who use the traditional IPSec VPN client with ASA ASAs and they work well.

  You are right that the granting of licenses for the SAA is complicated. Your tunnels IPSec VPN site-to-site will work on the SAA and pose much challenge in terms of licenses. But there are problems and alternative solutions to consider for remote access VPN clients. At this point, there are two major variants: you can use the classic IPSec VPN client or you can use the new AnyConnect client. From a licensing perspective there is a Hugh difference between them. It is not special license that applies to the traditional IPSec client and they are just against your license for peers Total VPN (for which you have 750 in your license). For the AnyConect there is a condition of licence. There is a premium for AnyConnect license and there are licensed AnyConnect Essentials. The Essentials license price is much lower than the premium license, but Essentials does not all the features that made the premium.

  In the immediate future, that it would sound like an easy question to answer, use the traditional IPSec VPN client for which theere is not a special permit and it is what you are used to. However Cisco has announced the dates of end of sale and end of Support for the traditional VPN client. If at some point you will need to use the AnyConnect client. I would say that if you make the change of the ASA that it might be a good choice to also adopt the AnyConnect client.

  HTH

  Rick

• ASA 5520 - VPN users have no internet.

  Hello

  We just migrated a Pix 515 and an ASA 5520 VPN concentrator.  The firewall part works fine, but we have some problem with our remote VPN.

  Everything inside network is accessible when you use VPN remote but there is no access to our perimeter network or the internet.  I don't know there's only something simple you need that I'm missing, and hoping someone can shed some light on what is needed to allow the VPN tunnel back outdoors and in our DMZ.

  The ASA is running 8.2 (2) 9 and ASDM 6.2 (1).

  See you soon,.

  Rob

  From the 172.16.68.0/24 you can PING 10.10.10.1 correct?

  The 10.10.10.0/24 you can PING 172.16.68.1 correct?

  I'm having a hard time find now how this tunnel is up since you have PFS
  activated on the SAA, but not on the PIX.

  Federico.

• How to change address e-mail iCloud?

  How to change address e-mail iCloud?

  Welcome to the Apple community.

  Unfortunately, you cannot change your iCloud email address.

  However, you can create an email alias to use parallel to it, you can do so at iCloud.com > Mail > settings (icon gear at the bottom of the page) > Preferences > accounts

• How many group Supportepar ASA 5520 vpn for remote access

  Hello

  Howmany vpn group is supported on asa 5520 with configuraion vpn remote access.

  Concerning

  1 if nat-control is disabled and you do not have any other order NAT in your config file, you do not have it. Try to remove the existing "NAT 0" command and "clear xlate."

  2. you must ensure that your network inside know they can go by ASA to access remote vpn client IP. You have any device layer 3 behind the ASA that does the routing. If so, please verify that this is the routing table.

• ASA 5520 - VPN using LDAP access control

  I'm setting up an ASA 5520 for VPN access.  Authorization & authentication using an LDAP server.  I have successfully configured tunnel, and I can access internal resources.  What I want to do now is to limit access to a specific ad group membership.  In the absence of this belonging to a group, a user cannot access the VPN.

  My VPN client software testing is Cisco Systems VPN Client 5.0.05.0290 Version.  The Group authentication is configured in a connection entry that identifies the Group of Tunnel. I think I wrote that correctly.

  The Version of the software on the SAA is 8.3 (1).

  My current challenge is getting the VPN to stop letting each request for access through little matter belonging to a group.  I found the thread below to be significantly useful, but there is obviously something which is not entirely mesh with my situation.

  https://supportforums.Cisco.com/message/3232649#3232649

  Thanking all in advance for everything offered thoughts and advice.

  Configuration (AAA LDAP, group policy and group of tunnel) is below.

  AAA-Server LDAP protocol ldap
  AAA-Server LDAP (inside) host x.x.y.12
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_MAP
  AAA-Server LDAP (inside) host x.x.y.10
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  LDAP-attribute-map LDAP_MAP
  AAA-Server LDAP (inside) host x.x.y.11
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_MAP

  AAA-Server LDAP (inside) host x.x.y.10
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  LDAP-attribute-map LDAP_MAP
  AAA-Server LDAP (inside) host x.x.y.11
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_MAP
  !
  internal group NOACCESS strategy
  NOACCESS group policy attributes
  VPN - concurrent connections 0
  Protocol-tunnel-VPN IPSec webvpn
  address pools no
  attributes of Group Policy DfltGrpPolicy
  VPN - 10 concurrent connections
  Protocol-tunnel-VPN IPSec webvpn
  enable IPSec-udp
  vpn group policy - pro internal
  vpn - pro group policy attributes
  value x.x.y.17 x.x.y.27 WINS server
  Server DNS value x.x.y.19 x.x.y.29
  VPN - 50 simultaneous connections
  Protocol-tunnel-VPN IPSec svc
  group-lock value vpn - pro
  field default value domain.com
  value of address ip-vpn-pro pools
  WebVPN
  client of dpd-interval SVC no
  dpd-interval SVC 1800 bridge
  !

  attributes global-tunnel-group DefaultRAGroup
  LDAP authentication group-server
  LDAP authorization-server-group
  Group Policy - by default-vpn-pro
  authorization required
  type group tunnel vpn - pro remote access
  attributes global-tunnel-group-vpn - pro
  LDAP authentication group-server
  Group-server-authentication (LDAP outside)
  LDAP authorization-server-group
  Group Policy - by default-vpn-pro
  band-Kingdom
  password-management
  band-band
  authorization required
  type tunnel-group NOACCESSGROUP remote access
  attributes global-tunnel-group NOACCESSGROUP
  LDAP authentication group-server
  NOACCESS by default-group-policy

  Hello

  The configuration of what you are looking for is a feature called DAP (Dynamic Access Policy)

  The following link will explain how to set up the same.

  http://www.ciscosystems.com/en/us/products/ps6120/products_white_paper09186a00809fcf38.shtml

  I hope this helps.

  Kind regards

  Anisha

  P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.

• VPN site to site & outdoor on ASA 5520 VPN client

  Hi, I'm jonathan rivero.

  I have an ASA 5520 Version 8.0 (2), I configured the site-to-site VPN and works very well, in the other device, I configured the VPN Client for remote users and works very well, but I try to cofigure 2 VPNs on ASA 5520 on the same outside interface and I have the line "outside_map interface card crypto outdoors (for VPN client). , but when I set up the "crypto map VPNL2L outside interface, it replaces the command', and so I can have only a single connection.

  the executed show.

  ASA1 (config) # sh run

  : Saved

  :

  ASA Version 8.0 (2)

  !

  hostname ASA1

  activate 7esAUjZmKQSFDCZX encrypted password

  names of

  !

  interface Ethernet0/0

  nameif inside

  security-level 100

  address 172.16.3.2 IP 255.255.255.0

  !

  interface Ethernet0/1

  nameif outside

  security-level 0

  IP 200.20.20.1 255.255.255.0

  !

  interface Ethernet0/1.1

  VLAN 1

  nameif outside1

  security-level 0

  no ip address

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/5

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  2KFQnbNIdI.2KYOU encrypted passwd

  passive FTP mode

  object-group, net-LAN

  object-network 172.16.0.0 255.255.255.0

  object-network 172.16.1.0 255.255.255.0

  object-network 172.16.2.0 255.255.255.0

  object-network 172.16.3.0 255.255.255.0

  object-group, NET / remote

  object-network 172.16.100.0 255.255.255.0

  object-network 172.16.101.0 255.255.255.0

  object-network 172.16.102.0 255.255.255.0

  object-network 172.16.103.0 255.255.255.0

  object-group network net-poolvpn

  object-network 192.168.11.0 255.255.255.0

  access list outside nat extended permit ip net local group object all

  access-list extended sheep allowed ip local object-group net object-group net / remote

  access-list extended sheep allowed ip local object-group net net poolvpn object-group

  access-list splittun-vpngroup1 extended permitted ip local object-group net net poolvpn object-group

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  outside1 MTU 1500

  IP local pool ippool 192.168.11.1 - 192.168.11.100 mask 255.255.255.0

  no failover

  ICMP unreachable rate-limit 100 burst-size 10

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 access list outside nat

  Route outside 0.0.0.0 0.0.0.0 200.20.20.1 1

  Route inside 172.16.0.0 255.255.255.0 172.16.3.2 1

  Route inside 172.16.1.0 255.255.255.0 172.16.3.2 1

  Route inside 172.16.2.0 255.255.255.0 172.16.3.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout, uauth 0:05:00 absolute

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec kilobytes of life security-association 400000

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  card crypto VPNL2L 1 match for sheep

  card crypto VPNL2L 1 set peer 200.30.30.1

  VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 20

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  !

  !

  internal vpngroup1 group policy

  attributes of the strategy of group vpngroup1

  banner value +++ welcome to Cisco Systems 7.0. +++

  value of 192.168.0.1 DNS server 192.168.1.1

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value splittun-vpngroup1

  value by default-ad domain - domain.local

  Split-dns value ad - domain.local

  the address value ippool pools

  username password asa1 VRTlLlJ48/PoDKjS encrypted privilege 15

  tunnel-group 200.30.30.1 type ipsec-l2l

  IPSec-attributes tunnel-group 200.30.30.1

  pre-shared-key *.

  type tunnel-group vpngroup1 remote access

  tunnel-group vpngroup1 General-attributes

  ippool address pool

  Group Policy - by default-vpngroup1

  vpngroup1 group of tunnel ipsec-attributes

  pre-shared-key *.

  context of prompt hostname

  Cryptochecksum:00000000000000000000000000000000

  : end

  ASA2 (config) #sh run

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  86400 seconds, duration of life crypto ipsec security association
  Crypto ipsec kilobytes of life security-association 400000
  card crypto VPNL2L 1 match for sheep
  card crypto VPNL2L 1 set peer 200.30.30.1
  VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
  VPNL2L interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 20
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  tunnel-group 200.30.30.1 type ipsec-l2l
  IPSec-attributes tunnel-group 200.30.30.1
  pre-shared key cisco

  my topology:

  

  I try with the following links, but did not work

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080912cfd.shtml

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml

  Best regards...

  "" I thing both the force of the SAA with the new road outside, why is that? ".

  without the road ASA pushes traffic inward, by default.

  In any case, this must have been a learning experience.

  Hopefully, this has been no help.

  Please rate, all the helful post.

  Thank you

  Rizwan Muhammed.

• Routing with Cisco ASA 5520 VPN

  I have installed IPsec vpn remote users in the Cisco ASA 5520 using RADIUS in my main network. Works very well. I have a site to my Cisco ASA5520 tunnels going to other sites, some of the tunnels have Cisco ASA and some have SonicWalls. I wish that my users VPN remote IPSec to be able to navigate in these tunnels is a site to access remote subnets attached to these tunnels. Do I need to use a combination of routing and the ACL? Or can I just use ACL only? Or just use routing only?

  Thank you

  Carlos

  Hello

  The key to set up here is the two ACL of VPN L2L end points that determine the 'interesting' traffic to connect VPN L2L. You will also need to confirm that the connection of the VPN Client is configured so that traffic to the remote sites have sent to the connection of the VPN client. There are also other things that you should check on your ASA plant

  Here most of the things you usually have to confirm

  • Set up 'permit same-security-traffic intra-interface' if it is already present in your configuration
    • This setting will allow connections to form between the hosts that are connected to the same interface on the ASA. In this case, applies because the VPN client users are connected to the interface 'outside' of the ASA and also remote sites are connected to the ASA to "external". If the traffic between the remote VPN Client and VPN L2L sites will be to enter and exit the same interface
  • You will need to check how the customer if configured VPN connection. Split or full Tunnel tunnel
    • If the connection of the VPN Client is configured as Split Tunnel then you need to add all the networks from the remote to the Split Tunnel, so that the connections between the VPN Client is transmitted to the ASA and from there connections VPN L2L
    • If the connection of the VPN Client is configured as full Tunnel, then there no problem that all traffic is transferred to the Client VPN connection all its assets
  • Define the VPN pool in the ACL of VPN L2L
    • You should make sure that the pool network VPN Client is defined in the ACL that define 'interesting' traffic to connect VPN L2L. So, you need to add the pool VPN VPN L2L configurations on the sites of Central America and remote control
  • Configure NAT0 / NAT exempt for remote VPN Client to L2L VPN Site traffic at both ends of the VPN L2L
    • You must ensure that the NAT0 / exempt NAT rules exist for the VPN Client for Remote Site traffic. This will have to be configured on the SAA "outside" interface. Format of configuration varies naturally a bit on the ASA Central his software level.

  These should be the most common things to set up and confirm for traffic to flow between the VPN Client and Remote Sites

  Hope this helps please rate if yes or ask more if necessary.

  -Jouni

• 1841. ASA 5520 VPN

  I set up a VPN site-to site between a Cisco ISR 1841 and a Cisco ASA 5520, everything seems to work but I have a few questions.

  1. I must explicitly authorize all VPN traffic in the ACL on the external interface of the 1841, y at - it an equivalent of router "vpn sysopt connection permit?

  2. Although the VPN rises and pass traffic, I have the opportunity to see what follows?

  * 14:11:52.883 22 June: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode has failed with the peer 1.1.1.1

  You can share the outputs full? Both sides at the same time?

  Bottom line, I don't think it's normal in IOS 12.4 mainline unless packages are leaking clear ;/

• Need help - ASA 5520 VPN issues

  Trying to simulate our in-lab recovery facility. I have 2 ASA 5520 who have a site - tunnel site between them.

  That works fine

  But I also have a requirement for remote access in one of the ASA, which formerly connected needs to route through

  the site - tunnel site to another server on the other side.

  So far the Remoting piece connects very well, I can access all networks connected locally but I can't seem to get the traffic

  to move through the site - site of the tunnel on the other side.

  Is this feasible? If so, if there are suggestions that would be appreciated.

  See you soon

  Dave

  The command is not applied to a specific interface.

  The command activate the feature on the ASA to receive traffic from VPN clients on the external interface and send him outside through the same apart from the interface through the tunnel L2L (and vice versa).

  Federico.

• How to change an existing in ASDM VPN tunnel?

  I currently have a VPN tunnel together upwards, but to change some of the configurations as making ikev2, replacing the SHA512 hash and change it in the DH group 14. I intend to do this in ASDM. I already created a group of tunnel ikev2 that I put the tunnel and created a Card Crypto that is configured with the right proposal ikev2 IPSec and Diffie-Hellman group. All other configurations such as the IP of Peer address and subnets configured and I'll work with the engineers at the other end of the tunnel to ensure that configurations are, I want to just make sure I'm not missing anything. Someone at - he never comes to change the configuration of an existing ASDM so tunnel, and it worked correctly? Here are the steps that I have will be taken as well as those I've already mentioned:

  -Edit the connection profile so that the name of group policy use the correct tunnel that was created for ikev2

  -Enter the pre-shared key local and remote pre-shared key ikev2 tab

  -Change the IKE Policy so that it uses the ikev2 policy that was created to use SHA512

  -Modify the IPSEC proposal so that it uses AES256-SHA512

  -THE CRYPTO MAP IS ALREADY CREATED

  -Change the secret of transfer perfect in group 14

  Hello

  Let me go through your questions to clarify this double:

  1. If I have a Crypto map applied to my external interface with a proposal of IPSec of ikev1 can I just add a proposal ikev2 in this Crypto map as well?

  If you have a card encryption applied to different peers outside and 3 with different order number, you will need to replace the proposal for the peer using IKEv2: IKEv2 IKEv1, the others must continue to use their IKEv1 IPSec proposal.

  2. so can I add an ikev2 with AES256 SHA512 hash proposal to my 123.123.123.456 tunnel group and continue to have all three tunnel groups always pass traffic? What happens if I add the proposal ikev2, but REMOVE the ikev1 this group of tunnel proposal because I don't want this group of tunnel use one other than AES256-SHA512 hash?

  123.123.123.456 - ikev2 - AES256-SHA512

  I would like to expand this a little more, if her counterpart 123.123.123.456, must use IKEv2, you need to declare the IKEv2 in the tunnel group and add the relevant "Local and remote PSK"--> is for phase 1, and this means that it will use the IKEv2 defined policy before, and IPSec IKEv2 proposal is on phase 2, where the encryption card is you will need to replace the IKEv1 and use IPSec IKEv2 proposal. That way it will use for the phase 1 of the policy of IKEv2, that you set and defined transformation IKEv2, by making this change make sure that both sides are mirrored with IKEv2 and IPSec policy projects, as well as the tunnel will remain and will come with the new proposals.

  This custom affect no matter what another tunnel, as long as you change the settings to the correct tunnel group and do not delete all the proposals, simply remove the profile connection, those employees.

  3. you know what I mean? All groups of three tunnels on that off interface use different cryptographic cards, with only two of the three using ikev1 as a proposal of IPSec. Which will work?

  You can only have one card encryption applied by interface, and 3 tunnels using different sequence number with the same crypto map name, you cannot 2 tunnels on the same card encryption using IKEV1, and always in the same encryption card have the third tunnel using IKEv2 (different transformation defined using IKEv2). This custom cause no problem. 

  4. what Group Policy DfltGrpPolicy? Currently use all my groups of tunnel, but it is configured for ikev1. I'm not really sure what role is in everything it can so I simply add ikev2?

  Default group policy is added by default to all your groups of tunnel (connection profile), whenever create you one default group policy is inherited him by default, you can change to group policy that you can create, group policy is a set of attributes that will be used to define something or limit , for example, for a site, you can configure a VPN filter (filters the traffic that goes through the tunnel), now back to your topic, you define the protocols that will be negotiated as for an L2L IKEv1 or IKEv2, Anyconnect SSL or IKEv2, on default group policy, and so on, it is therefore important that you add the IKEv2 , so trading will be permitted, or both to create a new group policy and add the IKEv2 Protocol; and in the tunnel group, add the group policy relevant, that you just created.

  I hope that this is precisely, keep me posted!

  Please go to the note, and mark it as correct this post and the previous that it helped you!

  David Castro,

• How to change address billing from one country to another

  I moved from the United Kingdom to South Africa and my current credit card is linked to my new address here. However I can't update my billing information, because the field where I enter my zip code does not accept the format of my current zip code (which is different from my old)

  The country of your payment address, the country on your Adobe account and the store you purchase of should be the same.

  FAQ: How can I change the country associated with my Adobe ID?

  FAQ: How do I change my credit card information?

  You can contact our support for assistance staff:

  FAQ: How to contact Adobe for support?

• ASA 5520 VPN

  Hello

  Ask for help if it is possible to have both SSL & ipsec site to site vpn configured on a 5520. If so, would there be no degradation of performance or any limitation of no.. users are allowed.

  Any other things I need to know in this respect.

  Appreciate your help,

  Thank you.

  Yes, you can have the SSL VPN, IPSec Site to site, but also remote access IPSec VPN configured and running simultaneously.

  Here's what ASA5520 can support:

  -IPSec 750 (Inc. VPN Site-to-Site and remote access)

  -750 SSL VPN

  http://www.Cisco.com/en/us/products/ps6120/prod_models_comparison.html

  Please note that for SSL VPN, it only comes with license 2 by default, and you must purchase the SSL license if you want to run more than 2 SSL VPN sessions simultaneously.

  Hope that helps.

• ISPS double and two redundant ASA 5520 VPN tunnels

  Hi all

  I have a requirement that looks like this:

  -with two ISPs (of course public IP of different subnets), I have two firewalls that we have to do 2 l2l VPN tunnels.

  Virtual private networks will be redundant to each other and in the case where one of the links is congested, traffic should pass through the other tunnel.

  Did someone do something like that?

  Thank you

  Vlad

  Hi Vlad,

  To have redundant connections, I suggest the following link:

  ASA/PIX 7.x: example of redundant Configuration or backup ISP links

  To find out when the link is congested? I don't think it could be possible at all on the SAA, with a UDP IP SLA jitter, but I think that it is supported only on IOS routers.

  Analysis of IP Service levels using the UDP IP SLA jitter operation

  Thank you.

  Portu.

  Please note all messages that will be useful.

• How to change address MAC of Console of Service?

  Our network department wants the MAC addresses to create DHCP reservations for all systems with a fixed IP address.

  We have provided all service consoles virtual MAC addresses on our ESX 3.5 U4 machines. This method works.

  After reinstalled an ESX after a failure of the drive, our MAC service console has changed. I am looking for a way to configure the MAC address of the former esx Server installation.

  Is it possible somehow?

  Edit/etc/sysconfig/network-scripts/ifcfg-vswif0 and restart the network.

  ---

  VMware vExpert 2009

  http://blog.vadmin.ru