Routing with Cisco ASA 5520 VPN

I have installed IPsec vpn remote users in the Cisco ASA 5520 using RADIUS in my main network. Works very well. I have a site to my Cisco ASA5520 tunnels going to other sites, some of the tunnels have Cisco ASA and some have SonicWalls. I wish that my users VPN remote IPSec to be able to navigate in these tunnels is a site to access remote subnets attached to these tunnels. Do I need to use a combination of routing and the ACL? Or can I just use ACL only? Or just use routing only?

Thank you

Carlos

Hello

The key to set up here is the two ACL of VPN L2L end points that determine the 'interesting' traffic to connect VPN L2L. You will also need to confirm that the connection of the VPN Client is configured so that traffic to the remote sites have sent to the connection of the VPN client. There are also other things that you should check on your ASA plant

Here most of the things you usually have to confirm

  • Set up 'permit same-security-traffic intra-interface' if it is already present in your configuration

    • This setting will allow connections to form between the hosts that are connected to the same interface on the ASA. In this case, applies because the VPN client users are connected to the interface 'outside' of the ASA and also remote sites are connected to the ASA to "external". If the traffic between the remote VPN Client and VPN L2L sites will be to enter and exit the same interface
  • You will need to check how the customer if configured VPN connection. Split or full Tunnel tunnel
    • If the connection of the VPN Client is configured as Split Tunnel then you need to add all the networks from the remote to the Split Tunnel, so that the connections between the VPN Client is transmitted to the ASA and from there connections VPN L2L
    • If the connection of the VPN Client is configured as full Tunnel, then there no problem that all traffic is transferred to the Client VPN connection all its assets
  • Define the VPN pool in the ACL of VPN L2L
    • You should make sure that the pool network VPN Client is defined in the ACL that define 'interesting' traffic to connect VPN L2L. So, you need to add the pool VPN VPN L2L configurations on the sites of Central America and remote control
  • Configure NAT0 / NAT exempt for remote VPN Client to L2L VPN Site traffic at both ends of the VPN L2L
    • You must ensure that the NAT0 / exempt NAT rules exist for the VPN Client for Remote Site traffic. This will have to be configured on the SAA "outside" interface. Format of configuration varies naturally a bit on the ASA Central his software level.

These should be the most common things to set up and confirm for traffic to flow between the VPN Client and Remote Sites

Hope this helps please rate if yes or ask more if necessary.

-Jouni

Tags: Cisco Security

Similar Questions

  • What VPN work as a PPTP vpn firewall CISCO-ASA-5520.

    Hi all

    Can you please tell me which replace the VPN I can configure PPTP on ASA 5520 firewall. What VPN work as a PPTP vpn firewall CISCO-ASA-5520.

    You can use the wizard VPN of RA with ASDM and confiugre L2TP IPSEC VPN that does not need a VPN Client must be installed.

    Michael

    Please note all useful posts

  • Is supported PPTP vpn cisco ASA 5520 firewall?

    Hi all

    I'm Md.kamruzzaman. My compnay buy a firewall of cisco asa 5520 and I want to configure PPTP vpn on asa 5520 firewall. Is it possible to configure the PPTP vpn to asa firewall. If possible can you please tell me what is the procedure to configure the PPTP vpn.

    Best regards

    MD.kamruzzaman

    Sorry, but the Cisco ASA firewall does not support PPTP VPN termination.

    You may terminate IPSec and SSL VPN but not of type PPTP.

    If you are new to the ASA, how best to configure the supported VPN types is via the VPN Wizard integrated into the application of management of ASSISTANT Deputy Ministers.

  • Cisco ASA 5510 VPN Site to Site with Sonicwall

    I am trying to configure a tunnel between a Cisco ASA 5510 VPN (Version 8.2 (2)) and TZ200 Sonicwall. I rose tunnel and go and I am able to ping the internal IP address of Cisco ASA of the Sonicwall LAN but nothing work. When I try to ping a host behind the Cisco ASA of the Sonicwall LAN I get the following message "rules asymmetrical NAT matched for flows forward and backward; Connection for tcp src outside:10.20.10.x/xxxx dst inside:10.20.2.x/xxxx refused due to failure of reverse path of NAT"on the SAA

    Googling the error above shows the problems with version 8.3 or later that resembled the nat commands have been changed SAA, train is still on 8.2 but I another common question does not add an exemption of NAT I have double-triple checked that I did add an exception rule of NAT of the hosts on the network from cisco for the guests of the Sonicwall network. Looks like I hit a road block so any help would be appreciated. Thank you

    Here are a few excertps of the config file (10.20.2.0 behind the cisco) and 10.20.10.0 behind the sonicwall

    NAT (inside) 0 access-list sheep

    ..

    IP 10.20.2.0 allow Access-list extended sheep 255.255.255.0 10.20.10.0 255.255.255.0

    access extensive list ip 10.20.2.0 outside_1_cryptomap allow 255.255.255.0 10.20.10.0 255.255.255.0

    ..

    card crypto outside_map 1 match address outside_1_cryptomap

    card crypto outside_map 1 set counterpart x.x.x.x

    card crypto outside_map 1 set of transformation-ESP-3DES-SHA

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    ..

    crypto ISAKMP allow outside

    crypto ISAKMP policy 5

    preshared authentication

    3des encryption

    sha hash

    Group 2

    lifetime 28800

    ..

    internal SiteToSitePolicy group strategy

    attributes of Group Policy SiteToSitePolicy

    VPN-idle-timeout no

    Protocol-tunnel-VPN IPSec

    Split-tunnel-network-list no

    ..

    tunnel-group x.x.x.x type ipsec-l2l

    tunnel-group x.x.x.x General attributes

    Group Policy - by default-SiteToSitePolicy

    tunnel-group ipsec-attributes x.x.x.x

    pre-shared key *.

    ..

    Added some excerpts from the configuration file

    Hello Manjitriat,

    Okay, detected IPSEC parody is normal, that means you are trying to send unencrypted on a line of encrypted packets.

    Now, if you see on the plotter of package that traffic will hollow the VPN channel all its fine in your site.

    Now the packet tracer must be something like this:

    entrance to Packet-trace inside private_ip_lan destination_private_ip_lan 1025 tcp 80

    Please provide us with the result of the following instructions after you run the packet tracer.

    See the crypto Isakamp SA

    See the crypto Ipsec SA

    Kind regards

    Julio

  • How Anyconnect VPN users will connect with cisco ASA, which uses the server (domain controller) Radius for authentication

    Hi team

    Hope you do well. !!!

    currently I am doing a project which consists in CISCO ASA-5545-X, RADIUS (domain controller) server for authentication. Here, I need to configure Anyconnect VPN and host checker in cisco asa.

    1 users will connect: user advanced browser on SSL VPN pop past username and password.

    2. (cisco ASA) authentication: VPN sends credentials to the RADIUS server.

    3 RADIUS server: authentication: receipt and SSL VPN (ASA) group.

    4 connectivity creation: If employee: PC so NAW verified compliance, no PC check Assign user to the appropriate role and give IP.

    This is my requirement, so someone please guide me how to set up step by step.

    1. how to set up the Radius Server?

    2. how to configure CISCO ASA?

    Thanks in advance.

    Hey Chick,

    Please consult the following page of installation as well as ASA Radius server. The ASA end there is frankly nothing much difference by doing this.

    http://www.4salesbyself.com/1configuring-RADIUS-authentication-for-webvp...

    Hope this helps

    Knockaert

  • 1841. ASA 5520 VPN

    I set up a VPN site-to site between a Cisco ISR 1841 and a Cisco ASA 5520, everything seems to work but I have a few questions.

    1. I must explicitly authorize all VPN traffic in the ACL on the external interface of the 1841, y at - it an equivalent of router "vpn sysopt connection permit?

    2. Although the VPN rises and pass traffic, I have the opportunity to see what follows?

    * 14:11:52.883 22 June: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode has failed with the peer 1.1.1.1

    You can share the outputs full? Both sides at the same time?

    Bottom line, I don't think it's normal in IOS 12.4 mainline unless packages are leaking clear ;/

  • Cisco ASA 5505 VPN Site to Site

    Hi all

    First post on the forums. I have worked with Cisco ASA 5505 for a few months and I recently bought a 2nd ASA to implement tunnel VPN Site to Site. It seems so simple in the number of videos watched on the internet. But when I did he surprise it did work for me... I've removed the tunnels, a number of times and tried to recreate. I use the VPN Wizard in the SMA to create the tunnel. Both the asa 5505 of are and have the same firmware even etc..

    I'd appreciate any help that can be directed to this problem please.  Slowly losing my mind

    Please see details below:

    Two ADMS are 7.1

    IOS

    ASA 1

    Nadia

    :

    ASA Version 9.0 (1)

    !

    hostname PAYBACK

    activate the encrypted password of HSMurh79NVmatjY0

    volatile xlate deny tcp any4 any4

    volatile xlate deny tcp any4 any6

    volatile xlate deny tcp any6 any4

    volatile xlate deny tcp any6 any6

    volatile xlate deny udp any4 any4 eq field

    volatile xlate deny udp any4 any6 eq field

    volatile xlate deny udp any6 any4 eq field

    volatile xlate deny udp any6 any6 eq field

    2KFQnbNIdI.2KYOU encrypted passwd

    names of

    local pool VPN1 192.168.50.1 - 192.168.50.254 255.255.255.0 IP mask

    !

    interface Ethernet0/0

    switchport access vlan 2

    Speed 100

    full duplex

    !

    interface Ethernet0/1

    link Trunk Description of SW1

    switchport trunk allowed vlan 1,10,20,30,40

    switchport trunk vlan 1 native

    switchport mode trunk

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    interface Vlan1

    No nameif

    no level of security

    no ip address

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP 92.51.193.158 255.255.255.252

    !

    interface Vlan10

    nameif inside

    security-level 100

    IP 192.168.10.1 255.255.255.0

    !

    interface Vlan20

    nameif servers

    security-level 100

    address 192.168.20.1 255.255.255.0

    !

    Vlan30 interface

    nameif printers

    security-level 100

    192.168.30.1 IP address 255.255.255.0

    !

    interface Vlan40

    nameif wireless

    security-level 100

    192.168.40.1 IP address 255.255.255.0

    !

    connection line banner welcome to the Payback loyalty systems

    boot system Disk0: / asa901 - k8.bin

    passive FTP mode

    summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00

    DNS domain-lookup outside

    DNS lookup field inside

    domain-lookup DNS servers

    DNS lookup domain printers

    DNS domain-lookup wireless

    DNS server-group DefaultDNS

    Server name 83.147.160.2

    Server name 83.147.160.130

    permit same-security-traffic inter-interface

    network obj_any object

    subnet 0.0.0.0 0.0.0.0

    ftp_server network object

    network of the Internal_Report_Server object

    Home 192.168.20.21

    Description address internal automated report server

    network of the Report_Server object

    Home 89.234.126.9

    Description of server automated reports

    service object RDP

    service destination tcp 3389 eq

    Description RDP to the server

    network of the Host_QA_Server object

    Home 89.234.126.10

    Description QA host external address

    network of the Internal_Host_QA object

    Home 192.168.20.22

    host of computer virtual Description for QA

    network of the Internal_QA_Web_Server object

    Home 192.168.20.23

    Description Web Server in the QA environment

    network of the Web_Server_QA_VM object

    Home 89.234.126.11

    Server Web Description in the QA environment

    service object SQL_Server

    destination eq 1433 tcp service

    network of the Demo_Server object

    Home 89.234.126.12

    Description server set up for the product demo

    network of the Internal_Demo_Server object

    Home 192.168.20.24

    Internal description of the demo server IP address

    network of the NETWORK_OBJ_192.168.20.0_24 object

    subnet 192.168.20.0 255.255.255.0

    network of the NETWORK_OBJ_192.168.50.0_26 object

    255.255.255.192 subnet 192.168.50.0

    network of the NETWORK_OBJ_192.168.0.0_16 object

    Subnet 192.168.0.0 255.255.0.0

    service object MSSQL

    destination eq 1434 tcp service

    MSSQL port description

    VPN network object

    192.168.50.0 subnet 255.255.255.0

    network of the NETWORK_OBJ_192.168.50.0_24 object

    192.168.50.0 subnet 255.255.255.0

    service object TS

    tcp destination eq 4400 service

    service of the TS_Return object

    tcp source eq 4400 service

    network of the External_QA_3 object

    Home 89.234.126.13

    network of the Internal_QA_3 object

    Home 192.168.20.25

    network of the Dev_WebServer object

    Home 192.168.20.27

    network of the External_Dev_Web object

    Home 89.234.126.14

    network of the CIX_Subnet object

    255.255.255.0 subnet 192.168.100.0

    network of the NETWORK_OBJ_192.168.10.0_24 object

    192.168.10.0 subnet 255.255.255.0

    network of the NETWORK_OBJ_84.39.233.50 object

    Home 84.39.233.50

    network of the NETWORK_OBJ_92.51.193.158 object

    Home 92.51.193.158

    network of the NETWORK_OBJ_192.168.100.0_24 object

    255.255.255.0 subnet 192.168.100.0

    network of the NETWORK_OBJ_192.168.1.0_24 object

    subnet 192.168.1.0 255.255.255.0

    object-group service DM_INLINE_SERVICE_1

    the tcp destination eq ftp service object

    the purpose of the tcp destination eq netbios-ssn service

    the purpose of the tcp destination eq smtp service

    service-object TS

    the Payback_Internal object-group network

    object-network 192.168.10.0 255.255.255.0

    object-network 192.168.20.0 255.255.255.0

    object-network 192.168.40.0 255.255.255.0

    object-group service DM_INLINE_SERVICE_3

    the purpose of the service tcp destination eq www

    the purpose of the tcp destination eq https service

    service-object TS

    service-object, object TS_Return

    object-group service DM_INLINE_SERVICE_4

    service-object RDP

    the purpose of the service tcp destination eq www

    the purpose of the tcp destination eq https service

    object-group service DM_INLINE_SERVICE_5

    purpose purpose of the MSSQL service

    service-object RDP

    service-object TS

    object-group Protocol TCPUDP

    object-protocol udp

    object-tcp protocol

    object-group service DM_INLINE_SERVICE_6

    service-object TS

    service-object, object TS_Return

    the purpose of the service tcp destination eq www

    the purpose of the tcp destination eq https service

    Note to outside_access_in to access list that this rule allows Internet the interal server.

    Notice on the outside_access_in of the access-list allowed:

    Comment from outside_access_in-list of FTP access

    Comment from outside_access_in-RDP access list

    Comment from outside_access_in-list of SMTP access

    Note to outside_access_in to access list Net Bios

    Comment from outside_access_in-SQL access list

    Comment from outside_access_in-list to access TS - 4400

    outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_1 any4 Internal_Report_Server

    access host access-list outside_access_in note rule internal QA

    Notice on the outside_access_in of the access-list allowed:

    Comment from outside_access_in-HTTP access list

    Comment from outside_access_in-RDP access list

    outside_access_in list extended access permitted tcp any4 object Internal_Host_QA eq www

    Notice on the outside_access_in of the access-list access to the internal Web server:

    Notice on the outside_access_in of the access-list allowed:

    Comment from outside_access_in-HTTP access list

    Comment from outside_access_in-RDP access list

    outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_3 any4 Internal_QA_Web_Server

    Note to outside_access_in to access list rule allowing access to the demo server

    Notice on the outside_access_in of the access-list allowed:

    Comment from outside_access_in-RDP access list

    Comment from outside_access_in-list to access MSSQL

    outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_4 any4 Internal_Demo_Server

    outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_5 any object Internal_QA_3

    Note to outside_access_in access to the development Web server access list

    outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_6 any object Dev_WebServer

    AnyConnect_Client_Local_Print deny any4 any4 ip extended access list

    AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq lpd

    Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

    AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 631

    print the access-list AnyConnect_Client_Local_Print Note Windows port

    AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 9100

    access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

    AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.251 any4 eq 5353

    AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

    AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.252 any4 eq 5355

    Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

    AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 EQ. 137

    AnyConnect_Client_Local_Print list extended access permitted udp any4 any4 eq netbios-ns

    Payback_VPN_splitTunnelAcl list standard access allowed 192.168.20.0 255.255.255.0

    permit outside_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0

    pager lines 24

    Enable logging

    information recording console

    asdm of logging of information

    address record

    [email protected] / * /.

    the journaling recipient

    [email protected] / * /.

    level alerts

    Outside 1500 MTU

    Within 1500 MTU

    MTU 1500 servers

    MTU 1500 printers

    MTU 1500 wireless

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm-711 - 52.bin

    don't allow no asdm history

    ARP timeout 14400

    no permit-nonconnected arp

    NAT (inside, outside) source Dynamics one interface

    NAT (wireless, outdoors) source Dynamics one interface

    NAT (servers, outside) no matter what source dynamic interface

    NAT (servers, external) static source Internal_Report_Server Report_Server

    NAT (servers, external) static source Internal_Host_QA Host_QA_Server

    NAT (servers, external) static source Internal_QA_Web_Server Web_Server_QA_VM

    NAT (servers, external) static source Internal_Demo_Server Demo_Server

    NAT (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination

    NAT (servers, external) static source Internal_QA_3 External_QA_3

    NAT (servers, external) static source Dev_WebServer External_Dev_Web

    NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

    NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination

    Access-group outside_access_in in interface outside

    Route outside 0.0.0.0 0.0.0.0 92.51.193.157 1

    Timeout xlate 03:00

    Pat-xlate timeout 0:00:30

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    identity of the user by default-domain LOCAL
    the ssh LOCAL console AAA authentication
    Enable http server
    http 192.168.10.0 255.255.255.0 inside
    http 192.168.40.0 255.255.255.0 wireless
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
    Crypto ipsec ikev2 AES256 ipsec-proposal
    Protocol esp encryption aes-256
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES192
    Protocol esp encryption aes-192
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES
    Esp aes encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 proposal ipsec 3DES
    Esp 3des encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal OF
    encryption protocol esp
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec pmtu aging infinite - the security association
    card crypto outside_map 1 match address outside_cryptomap
    card crypto outside_map 1 set pfs
    peer set card crypto outside_map 1 84.39.233.50
    card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
    outside_map interface card crypto outside
    trustpool crypto ca policy
    IKEv2 crypto policy 1
    aes-256 encryption
    integrity sha
    Group 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 10
    aes-192 encryption
    integrity sha
    Group 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 20
    aes encryption
    integrity sha
    Group 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 30
    3des encryption
    integrity sha
    Group 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 40
    the Encryption
    integrity sha
    Group 5
    FRP sha
    second life 86400
    Crypto ikev2 activate out of service the customer port 443
    Crypto ikev1 allow outside
    IKEv1 crypto policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH 77.75.100.208 255.255.255.240 outside
    SSH 192.168.10.0 255.255.255.0 inside
    SSH 192.168.40.0 255.255.255.0 wireless
    SSH timeout 5
    Console timeout 0

    dhcpd 192.168.0.1 dns
    dhcpd outside auto_config
    !
    dhcpd address 192.168.10.21 - 192.168.10.240 inside
    dhcpd dns 192.168.20.21 83.147.160.2 interface inside
    paybackloyalty.com dhcpd option 15 inside ascii interface
    dhcpd allow inside
    !
    dhcpd address 192.168.40.21 - 192.168.40.240 Wireless
    dhcpd dns 192.168.20.21 83.147.160.2 wireless interface
    dhcpd update dns of the wireless interface
    dhcpd option 15 ascii paybackloyalty.com wireless interface
    dhcpd activate wireless
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    internal Payback_VPN group strategy
    attributes of Group Policy Payback_VPN
    VPN - 10 concurrent connections
    Ikev1 VPN-tunnel-Protocol
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list Payback_VPN_splitTunnelAcl
    attributes of Group Policy DfltGrpPolicy
    value of 83.147.160.2 DNS server 83.147.160.130
    VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
    internal GroupPolicy_84.39.233.50 group strategy
    attributes of Group Policy GroupPolicy_84.39.233.50
    VPN-tunnel-Protocol ikev1, ikev2
    Noelle XB/IpvYaATP.2QYm username encrypted password
    Noelle username attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    username Éanna encrypted password privilege 0 vXILR9ZZQIsd1Naw
    Éanna attributes username
    VPN-group-policy Payback_VPN
    type of remote access service
    Michael qpbleUqUEchRrgQX of encrypted password username
    user name Michael attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    username, password from Danny .7fEXdzESUk6S/cC encrypted privilege 0
    user name Danny attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    Aileen tytrelqvV5VRX2pz encrypted password privilege 0 username
    user name Aileen attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    Aidan aDu6YH0V5XaxpEPg encrypted password privilege 0 username
    Aidan username attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
    shane.c iqGMoWOnfO6YKXbw encrypted password username
    username shane.c attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    Shane uYePLcrFadO9pBZx of encrypted password username
    user name Shane attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    username, encrypted James TdYPv1pvld/hPM0d password
    user name James attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    Mark yruxpddqfyNb.qFn of encrypted password username
    user name brand attributes
    type of service admin
    username password of Mary XND5FTEiyu1L1zFD encrypted
    user name Mary attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    Massimo vs65MMo4rM0l4rVu encrypted password privilege 0 username
    Massimo username attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    type tunnel-group Payback_VPN remote access
    attributes global-tunnel-group Payback_VPN
    VPN1 address pool
    Group Policy - by default-Payback_VPN
    IPSec-attributes tunnel-group Payback_VPN
    IKEv1 pre-shared-key *.
    tunnel-group 84.39.233.50 type ipsec-l2l
    tunnel-group 84.39.233.50 General-attributes
    Group - default policy - GroupPolicy_84.39.233.50
    IPSec-attributes tunnel-group 84.39.233.50
    IKEv1 pre-shared-key *.
    remote control-IKEv2 pre-shared-key authentication *.
    pre-shared-key authentication local IKEv2 *.
    !
    Global class-card class
    match default-inspection-traffic
    !
    !
    World-Policy policy-map
    Global category
    inspect the dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    Review the ip options
    inspect the netbios
    inspect the pptp
    inspect the rsh
    inspect the rtsp
    inspect the sip
    inspect the snmp
    inspect sqlnet
    inspect sunrpc
    inspect the tftp
    inspect xdmcp
    inspect the icmp error
    inspect the icmp
    !
    service-policy-international policy global
    192.168.20.21 SMTP server
    context of prompt hostname
    no remote anonymous reporting call
    call-home
    Profile of CiscoTAC-1
    no active account
    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
    email address of destination [email protected] / * /
    destination-mode http transport
    Subscribe to alert-group diagnosis
    Subscribe to alert-group environment
    Subscribe to alert-group monthly periodic inventory
    monthly periodicals to subscribe to alert-group configuration
    daily periodic subscribe to alert-group telemetry
    Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1

    ASA 2

    ASA Version 9.0 (1)

    !

    Payback-CIX hostname

    activate the encrypted password of HSMurh79NVmatjY0

    2KFQnbNIdI.2KYOU encrypted passwd

    names of

    !

    interface Ethernet0/0

    switchport access vlan 2

    Speed 100

    full duplex

    !

    interface Ethernet0/1

    Description this port connects to the local network VIRTUAL 100

    switchport access vlan 100

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    switchport access vlan 100

    !

    interface Ethernet0/4

    switchport access vlan 100

    !

    interface Ethernet0/5

    switchport access vlan 100

    !

    interface Ethernet0/6

    switchport access vlan 100

    !

    interface Ethernet0/7

    switchport access vlan 100

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP 84.39.233.50 255.255.255.240

    !

    interface Vlan100

    nameif inside

    security-level 100

    IP 192.168.100.1 address 255.255.255.0

    !

    banner welcome to Payback loyalty - CIX connection line

    passive FTP mode

    summer time clock gmt/idt recurring last Sun Mar 01:00 last Sun Oct 02:00

    DNS domain-lookup outside

    DNS lookup field inside

    DNS server-group defaultDNS

    Name-Server 8.8.8.8

    Server name 8.8.4.4

    permit same-security-traffic inter-interface

    network obj_any object

    subnet 0.0.0.0 0.0.0.0

    network of the host-CIX-1 object

    host 192.168.100.2

    Description This is the VM server host machine

    network object host-External_CIX-1

    Home 84.39.233.51

    Description This is the external IP address of the server the server VM host

    service object RDP

    source between 1-65535 destination eq 3389 tcp service

    network of the Payback_Office object

    Home 92.51.193.158

    service object MSQL

    destination eq 1433 tcp service

    network of the Development_OLTP object

    Home 192.168.100.10

    Description for Eiresoft VM

    network of the External_Development_OLTP object

    Home 84.39.233.52

    Description This is the external IP address for the virtual machine for Eiresoft

    network of the Eiresoft object

    Home 146.66.160.70

    Contractor s/n description

    network of the External_TMC_Web object

    Home 84.39.233.53

    Description Public address to the TMC Web server

    network of the TMC_Webserver object

    Home 192.168.100.19

    Internal description address TMC Webserver

    network of the External_TMC_OLTP object

    Home 84.39.233.54

    External targets OLTP IP description

    network of the TMC_OLTP object

    Home 192.168.100.18

    description of the interal target IP address

    network of the External_OLTP_Failover object

    Home 84.39.233.55

    IP failover of the OLTP Public description

    network of the OLTP_Failover object

    Home 192.168.100.60

    Server failover OLTP description

    network of the servers object

    subnet 192.168.20.0 255.255.255.0

    being Wired network

    192.168.10.0 subnet 255.255.255.0

    the subject wireless network

    192.168.40.0 subnet 255.255.255.0

    network of the NETWORK_OBJ_192.168.100.0_24 object

    255.255.255.0 subnet 192.168.100.0

    network of the NETWORK_OBJ_192.168.10.0_24 object

    192.168.10.0 subnet 255.255.255.0

    network of the Eiresoft_2nd object

    Home 137.117.217.29

    Description 2nd Eiresoft IP

    network of the Dev_Test_Webserver object

    Home 192.168.100.12

    Description address internal to the Test Server Web Dev

    network of the External_Dev_Test_Webserver object

    Home 84.39.233.56

    Description This is the PB Dev Test Webserver

    network of the NETWORK_OBJ_192.168.1.0_24 object

    subnet 192.168.1.0 255.255.255.0

    object-group service DM_INLINE_SERVICE_1

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_2

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_3

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_4

    service-object MSQL

    service-object RDP

    the tcp destination eq ftp service object

    object-group service DM_INLINE_SERVICE_5

    service-object MSQL

    service-object RDP

    the tcp destination eq ftp service object

    object-group service DM_INLINE_SERVICE_6

    service-object MSQL

    service-object RDP

    the Payback_Intrernal object-group network

    object-network servers

    Wired network-object

    wireless network object

    object-group service DM_INLINE_SERVICE_7

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_8

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_9

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_10

    service-object MSQL

    service-object RDP

    the tcp destination eq ftp service object

    object-group service DM_INLINE_SERVICE_11

    service-object RDP

    the tcp destination eq ftp service object

    outside_access_in list extended access allow object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-host-1

    Note to access list OLTP Development Office of recovery outside_access_in

    outside_access_in list extended access allow DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP object-group

    Comment from outside_access_in-access Eiresoft access list

    outside_access_in list extended access allow DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP object-group

    outside_access_in list extended access allow DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver object-group

    Note to outside_access_in access to OLTP for target recovery Office Access list

    outside_access_in list extended access allow DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP object-group

    outside_access_in list extended access allow DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover object-group

    Note to outside_access_in access-list that's allowing access of the Eiresoft on the failover OLTP server

    outside_access_in list extended access allow DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover object-group

    Comment from outside_access_in-access list access for the 2nd period of INVESTIGATION of Eiresoft

    outside_access_in list extended access allow DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP object-group

    Note to outside_access_in access from the 2nd IP Eiresoft access list

    outside_access_in list extended access allow DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover object-group

    outside_access_in list extended access allow DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver object-group

    outside_access_in list extended access allow DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP object-group

    outside_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.10.0 255.255.255.0

    pager lines 24

    Enable logging

    asdm of logging of information

    Outside 1500 MTU

    Within 1500 MTU

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    no permit-nonconnected arp

    NAT (inside, outside) source Dynamics one interface

    NAT (inside, outside) static source CIX-host-1 External_CIX-host-1

    NAT (inside, outside) static source Development_OLTP External_Development_OLTP

    NAT (inside, outside) static source TMC_Webserver External_TMC_Web

    NAT (inside, outside) static source TMC_OLTP External_TMC_OLTP

    NAT (inside, outside) static source OLTP_Failover External_OLTP_Failover

    NAT (inside, outside) static source Dev_Test_Webserver External_Dev_Test_Webserver

    NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination

    NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

    Access-group outside_access_in in interface outside

    Route outside 0.0.0.0 0.0.0.0 84.39.233.49 1

    Timeout xlate 03:00

    Pat-xlate timeout 0:00:30

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    identity of the user by default-domain LOCAL

    the ssh LOCAL console AAA authentication

    Enable http server

    http 92.51.193.156 255.255.255.252 outside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit

    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac

    Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac

    Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac

    Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac

    Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit

    Crypto ipsec ikev2 ipsec-proposal OF

    encryption protocol esp
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 proposal ipsec 3DES
    Esp 3des encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES
    Esp aes encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES192
    Protocol esp encryption aes-192
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 AES256 ipsec-proposal
    Protocol esp encryption aes-256
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec pmtu aging infinite - the security association
    card crypto outside_map 1 match address outside_cryptomap
    card crypto outside_map 1 set pfs
    peer set card crypto outside_map 1 92.51.193.158
    card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
    outside_map interface card crypto outside
    trustpool crypto ca policy
    IKEv2 crypto policy 1
    aes-256 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 10
    aes-192 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 20
    aes encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 30
    3des encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 40
    the Encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    Crypto ikev2 allow outside
    Crypto ikev1 allow outside
    IKEv1 crypto policy 10
    authentication crack
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 20
    authentication rsa - sig
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 30
    preshared authentication
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 40
    authentication crack
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 50
    authentication rsa - sig
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 60
    preshared authentication
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 70
    authentication crack
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 80
    authentication rsa - sig
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 90
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 100
    authentication crack
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 110
    authentication rsa - sig
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 120
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 130
    authentication crack
    the Encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 140
    authentication rsa - sig
    the Encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 150
    preshared authentication
    the Encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH 77.75.100.208 255.255.255.240 outside
    SSH 92.51.193.156 255.255.255.252 outside
    SSH timeout 5
    Console timeout 0

    dhcpd outside auto_config
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    internal GroupPolicy_92.51.193.158 group strategy
    attributes of Group Policy GroupPolicy_92.51.193.158
    VPN-tunnel-Protocol ikev1, ikev2
    username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
    tunnel-group 92.51.193.158 type ipsec-l2l
    tunnel-group 92.51.193.158 General-attributes
    Group - default policy - GroupPolicy_92.51.193.158
    IPSec-attributes tunnel-group 92.51.193.158
    IKEv1 pre-shared-key *.
    remote control-IKEv2 pre-shared-key authentication *.
    pre-shared-key authentication local IKEv2 *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    inspect the icmp
    !
    global service-policy global_policy
    context of prompt hostname
    no remote anonymous reporting call
    Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
    : end

    Hello

    There are some clear problems I see on a quick glance. These are not related to the actual VPN configuration but rather the NAT configurations.

    All your configuration of NAT CLI format above are configured as manual NAT / double NAT in Section 1. This means that the appliance NAT configurations have been added to the same section of the NAT configurations and scheduling of the NAT inside this Section rules is the cause of the problem for the L2L VPN connection for some.

    Here are a few suggestions on what to change

    ASA1

    Minimal changes

    the object of the LAN network

    192.168.10.0 subnet 255.255.255.0

    being REMOTE-LAN network

    255.255.255.0 subnet 192.168.100.0

    NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN

    no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination

    That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.

    Finally, we remove the old rule that generated the ASDM. It would do the same thing if it has been moved to the top, but I generally find the creation of the 'object' with descriptive names easier on the eyes in the long term.

    Other suggestions

    These changes are not necessary with regard to the VPN L2L. Here are some suggestions how to clean a part of NAT configurations.

    PAT-SOURCE network object-group

    source networks internal PAT Description

    object-network 192.168.10.0 255.255.255.0

    object-network 192.168.20.0 255.255.255.0

    object-network 192.168.40.0 255.255.255.0

    NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source

    No source (indoor, outdoor) nat Dynamics one interface

    no nat (wireless, outdoors) source Dynamics one interface

    no nat (servers, outside) no matter what source dynamic interface

    The above configuration creates a "object-group" that lists all internal networks that you have dynamic PAT configured so far. It then uses the ' object-group ' in a command unique 'nat' to manage the dynamic PAT for all internal networks (with the exception of printers who had nothing at first). Then we remove the old PAT dynamic configurations.

    Contains the command "nat" "car after" because it moving this "nat" configuration to the bottom of the NAT rules. For this reason its less likely to cause problems in the future.

    network of the SERVERS object

    subnet 192.168.20.0 255.255.255.0

    network of the VPN-POOL object

    192.168.50.0 subnet 255.255.255.0

    NAT (servers, external) 2 static static source of destination of SERVERS SERVERS VPN-VPN-POOL

    no nat (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination

    The above configuration is supposed to create a NAT0 configuration for traffic between the network and the pool of Client VPN server. To my knowledge the old configuration that remove us is not used because the traffic would have matched PAT rule dynamic server yet rather than this rule which is later in the NAT configurations and would not be addressed.

    no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

    It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.

    ASA2

    Minimal changes

    the object of the LAN network

    255.255.255.0 subnet 192.168.100.0

    being REMOTE-LAN network

    192.168.10.0 subnet 255.255.255.0

    NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN

    no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination

    That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.

    Finally, we remove the old rule that generated the ASDM.

    Other suggestions

    PAT-SOURCE network object-group

    object-network 192.168.100.0 255.255.255.0

    NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source

    No source (indoor, outdoor) nat Dynamics one interface

    The above configuration is supposed to do the same thing with the other ASA. Although given that this network contains only a single subnet it cleans the "nat" configurations exist that much. But the order of the "nat" configurations is changed to avoid further problems with the NAT order.

    no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

    It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.

    I suggest trying the changes related to VPN L2L first NAT0 configurations and test traffic. So who gets the work of connectivity, then you could consider changing other NAT configurations. There are other things that could be changed also in what concerns THAT static NAT servers but that probably better left for another time.

    Hope this makes any sense and has helped

    Remember to mark a reply as the answer if it answered your question.

    Feel free to ask more if necessary

    -Jouni

  • With an ASA 5520 port forwarding

    Hi all

    I recently bought a Cisco ASA 5520 on eBay for study and I decided to only use it as a firewall between my home LAN and Internet. Wow, what a learning curve! I managed to add my internal networks as objects and create a rule (thanks to youtube) NAT to PAT my internal devices out of the Internet with ASSISTANT Deputy Ministers, but I am really struggling to do the following:-

    -allow all incoming traffic that hits the outside interface for port 38921 and nat at 10.1.10.101:38921

    -allow all incoming traffic that hits the outside interface for port 30392 and nat at 10.1.10.101:30392

    Can someone guide me on how to do it, because I have a couple of services that run behind these ports on a server I want to get when I'm not at home? My (rather messy) config is as follows:-

    hostname FW1

    activate the encrypted password

    encrypted passwd

    names of

    !

    interface GigabitEthernet0/0

    Description * externally facing Internet *.

    nameif outside

    security-level 0

    IP address dhcp setroute

    !

    interface GigabitEthernet0/1

    Description * internal face to 3750 *.

    nameif inside

    security-level 100

    IP 10.1.10.2 255.255.255.0

    !

    interface GigabitEthernet0/2

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface GigabitEthernet0/3

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Management0/0

    nameif management

    security-level 100

    IP 192.168.1.1 255.255.255.0

    !

    passive FTP mode

    the VLAN1 object network

    subnet 192.168.1.0 255.255.255.0

    Legacy description

    network of the WiredLAN object

    10.1.10.0 subnet 255.255.255.0

    Wired LAN description

    network of the CorporateWifi object

    10.1.160.0 subnet 255.255.255.0

    Company Description 160 of VLAN wireless

    network of the GuestWifi object

    10.1.165.0 subnet 255.255.255.0

    Description Wireless VLAN 165 comments

    network of the LegacyLAN object

    subnet 192.168.1.0 255.255.255.0

    Description Legacy LAN in place until the change on

    the file server object network

    Home 10.1.10.101

    Description File Server

    service object Service1

    tcp source eq eq 38921 38921 destination service

    1 service Description

    the All_Inside_Networks object-group network

    network-object VLAN1

    network-object, object WiredLAN

    network-object, object CorporateWifi

    network-object, object GuestWifi

    network-object, object LegacyLAN

    object-group service Service2 tcp - udp

    port-object eq 30392

    object-group service DM_INLINE_TCPUDP_1 tcp - udp

    port-object eq 30392

    Group-object Service2

    object-group Protocol TCPUDP

    object-protocol udp

    object-tcp protocol

    Outside_access_in list extended access allowed object-group TCPUDP any inactive FileServer object-group DM_INLINE_TCPUDP_1 object

    Outside_access_in list extended access allowed object Service1 any inactive FileServer object

    pager lines 24

    Enable logging

    asdm of logging of information

    Outside 1500 MTU

    MTU 1500 internal

    management of MTU 1500

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 714.bin

    don't allow no asdm history

    ARP timeout 14400

    service interface NAT (inside, outside) dynamic source FileServer Service1 inactive Service1

    NAT (all, outside) interface dynamic source All_Inside_Networks

    Access-group Outside_access_in in interface outside

    Internal route 10.1.160.0 255.255.255.0 10.1.10.1 1

    Internal route 10.1.165.0 255.255.255.0 10.1.10.1 1

    Internal route 192.168.1.0 255.255.255.0 10.1.10.1 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    identity of the user by default-domain LOCAL

    Enable http server

    http 10.1.160.15 255.255.255.255 internal

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

    Telnet 10.1.160.15 255.255.255.255 internal

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    interface ID client DHCP-client to the outside

    management of 192.168.1.2 - dhcpd address 192.168.1.254

    enable dhcpd management

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    username privilege of encrypted password of Barry 15

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    context of prompt hostname

    no remote anonymous reporting call

    Cryptochecksum:19be38edefe8c3fd05e720aedee62c8e

    : end

    1. This is just one example of configuration and another option with to reason and avoid to send us the complete configuration of NAT:

    network of the 10.1.10.101 object

    Home 10.1.10.101

    service object 38921

    tcp source eq 38921 service

    service object 30392

    tcp source eq 30392 service

    NAT (inside, outside) 1 static source 10.1.10.101 38921 38921 service interface

    NAT (inside, outside) 1 static source 10.1.10.101 30392 30392 service interface

    Let me know if it works

  • ASA 5520 VPN licenses

    Community support,

    I want to run this question by you guys to avoid the sales of our partner CISCO and similar pitch more to the best solution that would give us what we want.

    We currently have a VPN from CISCO 3020 hub to terminate the Lan-to-Lan tunnels and have our mobile workers to connect through the client VPN CISCO (300 users-employees and contractors).

    Given that this device is coming to an end of LIFE this year, we bought a CISCO 5520 (here is the current licenses in this topic)

    Licensing seems quite complicated, so here's my question:

    -What VPN do you recommend for our users and entrepreneurs? I understand that the CISCO VPN client does not work with ASA 5500 Series devices

    Is there a license needed to deploy a VPN solution for our remote users(employees/contractors)?

    Thank you

    John

    The devices allowed for this platform:
    The maximum physical Interfaces: unlimited perpetual
    VLAN maximum: 150 perpetual
    Guests of the Interior: perpetual unlimited
    Failover: Active/active perpetual
    VPN - A: enabled perpetual
    VPN-3DES-AES: activated perpetual
    Security contexts: 2 perpetual
    GTP/GPRS: Disabled perpetual
    AnyConnect Premium peers: 2 perpetual
    AnyConnect Essentials: Disabled perpetual
    Counterparts in other VPNS: 750 perpetual
    Total VPN counterparts: 750 perpetual
    Shared license: disabled perpetual
    AnyConnect for Mobile: disabled perpetual
    AnyConnect Cisco VPN phone: disabled perpetual
    Assessment of Advanced endpoint: disabled perpetual
    Proxy UC phone sessions: 2 perpetual
    Proxy total UC sessions: 2 perpetual
    Botnet traffic filter: disabled perpetual
    Intercompany Media Engine: Disabled perpetual

    This platform includes an ASA 5520 VPN Plus license.

    Your understanding that the Cisco VPN client does not work with ASA is wrong. Maybe it's the version of Cisco VPN client that you use currently does not work with ASA. But these (and so not very new indeed) versions of VPN client work with the ASA. I installed for several clients who use the traditional IPSec VPN client with ASA ASAs and they work well.

    You are right that the granting of licenses for the SAA is complicated. Your tunnels IPSec VPN site-to-site will work on the SAA and pose much challenge in terms of licenses. But there are problems and alternative solutions to consider for remote access VPN clients. At this point, there are two major variants: you can use the classic IPSec VPN client or you can use the new AnyConnect client. From a licensing perspective there is a Hugh difference between them. It is not special license that applies to the traditional IPSec client and they are just against your license for peers Total VPN (for which you have 750 in your license). For the AnyConect there is a condition of licence. There is a premium for AnyConnect license and there are licensed AnyConnect Essentials. The Essentials license price is much lower than the premium license, but Essentials does not all the features that made the premium.

    In the immediate future, that it would sound like an easy question to answer, use the traditional IPSec VPN client for which theere is not a special permit and it is what you are used to. However Cisco has announced the dates of end of sale and end of Support for the traditional VPN client. If at some point you will need to use the AnyConnect client. I would say that if you make the change of the ASA that it might be a good choice to also adopt the AnyConnect client.

    HTH

    Rick

  • ASA 5520 - VPN users have no internet.

    Hello

    We just migrated a Pix 515 and an ASA 5520 VPN concentrator.  The firewall part works fine, but we have some problem with our remote VPN.

    Everything inside network is accessible when you use VPN remote but there is no access to our perimeter network or the internet.  I don't know there's only something simple you need that I'm missing, and hoping someone can shed some light on what is needed to allow the VPN tunnel back outdoors and in our DMZ.

    The ASA is running 8.2 (2) 9 and ASDM 6.2 (1).

    See you soon,.

    Rob

    From the 172.16.68.0/24 you can PING 10.10.10.1 correct?

    The 10.10.10.0/24 you can PING 172.16.68.1 correct?

    I'm having a hard time find now how this tunnel is up since you have PFS
    activated on the SAA, but not on the PIX.

    Federico.

  • IPsec VPN site to site between router problem Cisco ASA. Help, please

    Hello community,

    I'm stuck in configuring VPN site to site between ASA (OS 9.1) and router Cisco IOS (IOS 15, 2 - 4.M4)

    Attachment is router configuration and ASA. I also include the router debug output.

    It seems that the two parties must isakmp missmatch configuration, but I have already disabled the KeepAlive parameters. I also turn off PFS setting on both sides. But it does not work. I have no idea on this problem.

    Please help me. Any help appreciated.

    Thank you

     
     

    I didn't look any further, but this may be a reason:

     crypto map mymap 1 ipsec-isakmp dynamic dyn1

    The dynamic CM must always be the last sequence in a card encryption:

     no crypto map mymap 1 ipsec-isakmp dynamic dyn1 crypto map mymap 65000 ipsec-isakmp dynamic dyn1

    Try this first, then we can look further.

  • Cisco ASA 5510 VPN with PIX 515

    Hello

    I have VPN between Cisco ASA and Cisco PIX.

    I saw in my syslog server this error that appears once a day, more or less:

    Received a package encrypted with any HIS correspondent, drop

    I ve seen issue in another post, but in none of then the solution.

    Here are my files from the firewall configuration:

    Output from the command: 'show running-config '.

    : Saved
    :
    ASA Version 8.2 (1)
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    card crypto WAN_map2 2 corresponds to the address WAN_cryptomap_1
    card crypto WAN_map2 2 set pfs
    card crypto WAN_map2 2 peer 62.80.XX game. XX
    map WAN_map2 2 game of transformation-ESP-DES-MD5 crypto
    card crypto WAN_map2 2 defined security-association 2700 seconds life
    card crypto WAN_map2 2 set nat-t-disable
    card crypto WAN_map2 WAN interface
    enable LAN crypto ISAKMP
    ISAKMP crypto enable WAN
    crypto ISAKMP policy 1
    preshared authentication
    the Encryption
    md5 hash
    Group 5
    lifetime 28800
    No encryption isakmp nat-traversal
    tunnel-group 62.80.XX. XX type ipsec-l2l
    tunnel-group 62.80.XX. IPSec-attributes of XX
    pre-shared-key *.

    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

    8.0 (4) version PIX
    !
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    card encryption VPN_map2 3 corresponds to the address VPN_cryptomap_2
    card encryption VPN_map2 3 set pfs
    card crypto VPN_map2 3 peer 194.30.XX game. XX
    VPN_map2 3 transform-set ESP-DES-MD5 crypto card game
    card encryption VPN_map2 3 defined security-association life seconds 2700
    card encryption VPN_map2 3 set security-association kilobytes of life 4608000
    card VPN_map2 3 set nat-t-disable encryption
    VPN crypto map VPN_map2 interface
    crypto ISAKMP enable VPN
    crypto ISAKMP allow inside
    crypto ISAKMP policy 30
    preshared authentication
    the Encryption
    md5 hash
    Group 5
    lifetime 28800
    No encryption isakmp nat-traversal
    ISAKMP crypto am - disable
    attributes of Group Policy DfltGrpPolicy
    Protocol-tunnel-VPN IPSec
    tunnel-group 194.30.XX. XX type ipsec-l2l
    tunnel-group 194.30.XX. IPSec-attributes of XX
    pre-shared-key *.

    If you need more information dedailed ask me questions.

    Thanks in advance for your help.

    Javi

    Hi Javi,

    Please after the release of "see broadcasting DfltGrpPolicy of any political group." See if you have the "vpn-idle-timoeout" command configured in that. If so, please change to "vpn-idle-timeout no" and see if that stops at these popping up error messages.

    http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/uz.html#wp1571426

    Thank you and best regards,

    Assia

  • VPN site to site Linux OpenSwan with cisco ASA

    / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : Arial ; mso-bidi-theme-font : minor-bidi ;}

    I'm trying to create a vpn site-to site between Cisco ASA 5510 and OpenSwan Linux, after completing the configuration of part and came across the VPN tunnel but nothing passes through the tunnel.

    I use the software version 8.0 (4) on my firewall SAA, so doing any faces a problem like that.

    Appreciate your support

    Both bugs are for outgoing VPN traffic. But in your case, we saw 'read' County was '0' which means that ASA has not received any package of Linux in the VPN tunnel.

  • VPN site to site & outdoor on ASA 5520 VPN client

    Hi, I'm jonathan rivero.

    I have an ASA 5520 Version 8.0 (2), I configured the site-to-site VPN and works very well, in the other device, I configured the VPN Client for remote users and works very well, but I try to cofigure 2 VPNs on ASA 5520 on the same outside interface and I have the line "outside_map interface card crypto outdoors (for VPN client). , but when I set up the "crypto map VPNL2L outside interface, it replaces the command', and so I can have only a single connection.

    the executed show.

    ASA1 (config) # sh run

    : Saved

    :

    ASA Version 8.0 (2)

    !

    hostname ASA1

    activate 7esAUjZmKQSFDCZX encrypted password

    names of

    !

    interface Ethernet0/0

    nameif inside

    security-level 100

    address 172.16.3.2 IP 255.255.255.0

    !

    interface Ethernet0/1

    nameif outside

    security-level 0

    IP 200.20.20.1 255.255.255.0

    !

    interface Ethernet0/1.1

    VLAN 1

    nameif outside1

    security-level 0

    no ip address

    !

    interface Ethernet0/2

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Ethernet0/3

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Ethernet0/4

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Ethernet0/5

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    2KFQnbNIdI.2KYOU encrypted passwd

    passive FTP mode

    object-group, net-LAN

    object-network 172.16.0.0 255.255.255.0

    object-network 172.16.1.0 255.255.255.0

    object-network 172.16.2.0 255.255.255.0

    object-network 172.16.3.0 255.255.255.0

    object-group, NET / remote

    object-network 172.16.100.0 255.255.255.0

    object-network 172.16.101.0 255.255.255.0

    object-network 172.16.102.0 255.255.255.0

    object-network 172.16.103.0 255.255.255.0

    object-group network net-poolvpn

    object-network 192.168.11.0 255.255.255.0

    access list outside nat extended permit ip net local group object all

    access-list extended sheep allowed ip local object-group net object-group net / remote

    access-list extended sheep allowed ip local object-group net net poolvpn object-group

    access-list splittun-vpngroup1 extended permitted ip local object-group net net poolvpn object-group

    pager lines 24

    Within 1500 MTU

    Outside 1500 MTU

    outside1 MTU 1500

    IP local pool ippool 192.168.11.1 - 192.168.11.100 mask 255.255.255.0

    no failover

    ICMP unreachable rate-limit 100 burst-size 10

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0 access-list sheep

    NAT (inside) 1 access list outside nat

    Route outside 0.0.0.0 0.0.0.0 200.20.20.1 1

    Route inside 172.16.0.0 255.255.255.0 172.16.3.2 1

    Route inside 172.16.1.0 255.255.255.0 172.16.3.2 1

    Route inside 172.16.2.0 255.255.255.0 172.16.3.2 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout, uauth 0:05:00 absolute

    dynamic-access-policy-registration DfltAccessPolicy

    the ssh LOCAL console AAA authentication

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    86400 seconds, duration of life crypto ipsec security association

    Crypto ipsec kilobytes of life security-association 400000

    Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

    card crypto VPNL2L 1 match for sheep

    card crypto VPNL2L 1 set peer 200.30.30.1

    VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game

    map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

    outside_map interface card crypto outside

    crypto isakmp identity address

    crypto ISAKMP allow outside

    crypto ISAKMP policy 20

    preshared authentication

    3des encryption

    md5 hash

    Group 2

    life 86400

    crypto ISAKMP policy 30

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 65535

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    a basic threat threat detection

    Statistics-list of access threat detection

    !

    !

    internal vpngroup1 group policy

    attributes of the strategy of group vpngroup1

    banner value +++ welcome to Cisco Systems 7.0. +++

    value of 192.168.0.1 DNS server 192.168.1.1

    Split-tunnel-policy tunnelspecified

    Split-tunnel-network-list value splittun-vpngroup1

    value by default-ad domain - domain.local

    Split-dns value ad - domain.local

    the address value ippool pools

    username password asa1 VRTlLlJ48/PoDKjS encrypted privilege 15

    tunnel-group 200.30.30.1 type ipsec-l2l

    IPSec-attributes tunnel-group 200.30.30.1

    pre-shared-key *.

    type tunnel-group vpngroup1 remote access

    tunnel-group vpngroup1 General-attributes

    ippool address pool

    Group Policy - by default-vpngroup1

    vpngroup1 group of tunnel ipsec-attributes

    pre-shared-key *.

    context of prompt hostname

    Cryptochecksum:00000000000000000000000000000000

    : end

    ASA2 (config) #sh run

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
    86400 seconds, duration of life crypto ipsec security association
    Crypto ipsec kilobytes of life security-association 400000
    card crypto VPNL2L 1 match for sheep
    card crypto VPNL2L 1 set peer 200.30.30.1
    VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
    VPNL2L interface card crypto outside
    crypto isakmp identity address
    crypto ISAKMP allow outside
    crypto ISAKMP policy 20
    preshared authentication
    3des encryption
    md5 hash
    Group 2
    life 86400

    tunnel-group 200.30.30.1 type ipsec-l2l
    IPSec-attributes tunnel-group 200.30.30.1
    pre-shared key cisco

    my topology:

    I try with the following links, but did not work

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080912cfd.shtml

    http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml

    Best regards...

    "" I thing both the force of the SAA with the new road outside, why is that? ".

    without the road ASA pushes traffic inward, by default.

    In any case, this must have been a learning experience.

    Hopefully, this has been no help.

    Please rate, all the helful post.

    Thank you

    Rizwan Muhammed.

  • How many group Supportepar ASA 5520 vpn for remote access

    Hello

    Howmany vpn group is supported on asa 5520 with configuraion vpn remote access.

    Concerning

    1 if nat-control is disabled and you do not have any other order NAT in your config file, you do not have it. Try to remove the existing "NAT 0" command and "clear xlate."

    2. you must ensure that your network inside know they can go by ASA to access remote vpn client IP. You have any device layer 3 behind the ASA that does the routing. If so, please verify that this is the routing table.

Maybe you are looking for

  • Join the tracks?

    Where is the join tracks option in iTunes 12.5.1.21?

  • Power supply Dell R520

    Hello I have 2-R520 both with single PS and I would like to know if it is possible to replace it with RPS? Y at - it duplicate an adapter to convert PS? Any comment is appreciated. Thank you

  • "Cannot open AsIO.sys! (2) »

    I have just upgraded from Vista to Windows 7 yesterday, and every time I come out of standby or restart my computer a message box saying "cannot open AsIO.sys! (2)"appears anywhere from 1 to 3 times.  I don't have any idea what this.  Any help would

  • I can't change my user account type

    I can't change it back my administrator account type, I accidentally change standard user. How can I change it to administrator? I use window7

  • BlackBerry smartphone Curve 8900 - deleting e-mail, opening more old/new

    Hello I get a lot of system notifications in my email address. I have check and then delete them. What I would like to be able to do is: -. Open the email, read it, delete it and it automatically opens the next oldest most recent e-mail or overnight.