How to configure an ip address reversed in exchange server 2003

Similar Questions

• How to configure to allow users in my web server behind a PIX 501

  I have 1 web server, 4 web hosting sites. IP addresses are like:

  the area of the web server itself: 192.168.111.11

  1 web site on this box has IP 192.168.111.101

  2nd ............................................ 192.168.111.102

  3rd ............................................. 192.168.111.103

  4th ............................................. 192.168.111.104

  My OUTSIDE interface (say) 205.200.20.5

  My INSIDE interface has 192.168.111.1

  I want to leave the outside web traffic in my web server box that hosts 4 sites. I only let people with HTTP and HTTPS.

  How should I do and for purposes of flexibility, say also tomorrow I want to host my site on a different web server #3 but always with the same IP address, can I selectively route certain web traffic to the boxes in different web server?

  Also, I want to open another port, say, 8080 for administrative purposes. Can I route HTTP or HTTPS, addressed to some port # to the Web server also?

  You will need to create static port mapped, but if you have only the external IP address a people can connect to, they will need to connect to a specific port in the URL to differentiate which internal web server, they really want to go.

  For example:

  > static (inside, outside) tcp 205.200.20.5 80 192.168.111.101 80 netmask 255.255.255.255

  > static (inside, outside) tcp 205.200.20.5 81 192.168.111.102 80 netmask 255.255.255.255

  > static (inside, outside) tcp 205.200.20.5 82 192.168.111.103 80 netmask 255.255.255.255

  > static (inside, outside) tcp 205.200.20.5 80 83 192.168.111.104 netmask 255.255.255.255

  maps of connections to 205.200.20.5 on port 80 through to port 80 on 192.168.111.101. Connections inbound to port 81 will be mapped through to port 80 on 192.168.111.102. Connections incoming on port 82 will be mapped through to port 80 on 192.168.111.103 and so on.

  You cannot map just all incoming traffic on port 80 to 4 different internal web servers, cause how the PIX will know which send traffic to.

  To allow access, as well as the static shown bove, you must:

  > list of allowed inbound tcp access any host 205.200.20.5 eq 80

  > list of allowed inbound tcp access any host 205.200.20.5 eq 81

  > list of allowed inbound tcp access any host 205.200.20.5 eq 82

  > list of allowed inbound tcp access any host 205.200.20.5 eq 83

  > list of allowed inbound tcp access any host 205.200.20.5 eq 443

  > interface entering outside acess group

  HTTPS is also going to be a problem, to do the same on HTTP, you need to use different ports to differentiate what specific internal web server that you want to that they go (and allow these ports in your "incoming" ACL above).

  To port 8080, just follow these steps:

  > static (inside, outside) 205.200.20.5 tcp 8080 192.168.111.10x 8080 netmask 255.255.255.255

  > list of allowed inbound tcp access any host 205.200.20.5 port 8080

  As you can probably guess, this won't work very well if you have only one external IP address, because users will not know to specify a specific port number so that they get through an internal host specific. You may have a single external address for each web server internal to this work in reality.

• How can I migrate my emails to an exchange server.

  I have my email accounts hosted by godaddy and I want to migrate everyone to Exchange Server. How can I do this?

  Hello

  Your Question is beyond the scope of this community.

  Kindly forward your Question in the TechNet Forums of Exchange Server.

  https://social.technet.Microsoft.com/forums/Exchange/en-us/home?category=ExchangeServer

  See you soon.

• How can we forget the administrator password in Windows Server 2003?

  How TO log in FORGOTTEN PASSWORD WINDOWS SERVER 2003 STANDARD EDITION administrator

  Why are you asking a question of Windows Server 2003 in this forum? What is there to do with the upgrade and activation of Windows XP installation?

  Post in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• How to configure the IP address on VMWare ESXi 3.5

  Hi all.  I installed the VMWare ESXi 3.5 on a test to dedicate

  Server, assign a private IP = 10.10.1.10 to the VMWare box (this box has 2 physical NETWORK card); and then I

  installed the Symantec BrightMail 9.0.2 as a virtual appliance on VMWare ESXi

  3.5 to act as an e-mail gateway.  BrightMail installation goes smooth.  However, I am not in a position

  to connect to the Internet inside BrightMail 9.  I have installed BrightMail for

  have 2 virtual network card.  Network 1 (eth0) got the IP =

  10.10.1.11, network 2 (eth1) got the IP = 82.132.33.45 (real

  public IP address).  With this settig BrightMail virtual machine is able to talk with the other PC in my LAN, howerver, it can't go on the Internet.  My network configuration is as follows:

  A router (Modem, with the public IP address) is directly connected to the VMware computer (the first NETWORK adapter), and then the VMWare (second NETWORK card) connects to a switch where other LAN PC also connects to.

  My question is,

  1. from BrightMail runs on top of the

  VMWare, how can I BrightMail to connect to the Internet and to the

  Moreover, it connects to my LAN?  Currently the machine has VMWare a

  10.10.1.10 private IP assigned address.

  I'm a bit confuse about the settings of the network on the VMWare itself (I'm not the network

  Guy).  Any suggestion is weclomed.  Thank you.

  the observed range, vmnic0 resembles your DMZ LAN and vmnic1 is your LAN (172.x.x.x) you can check you have the right cable to the correct port?

  then you are supposed not combined two NICs in a single portgroup. you will need to do vmnic0 as a new vswitch with new portgroup named DMZ Lan and change that in the virtual network adapter machine virtual 2 to use the DMZ LAN as the virtual switch.

  iDLE-jAM | SC 2, SC 3 & VCP 4

  If you have found this device or any other answer useful please consider useful or correct buttons using attribute points

• How to configure a lab overlooking tubular heat exchanger to get data

  HiI

  In our undergraduate engineering chemical labboratory we want to configure our DAq with lab VIEW tubular heat exchanger to get information on the temperature (flow cold fluid warms up), (the steam pressure on the side of the hull of the heat exchanger) and flow (water warms up).

  Can anyone suggest thermocouples, pressure transducers, and flow meters to stay between the heat exchanger and the acquisition of data?

  P.S. the heat exchanger is already equipped with a pressure gauge, thermometers and a rotameter, but we do not know how to connect these devices to data acquisition

  Looks like you have enough information to choose appropriate sensors, you just need to do the research. I start looking into Omega catalogue, or give them a call - they are generally useful. I can't take the time to spec parts for you - it would be a lot of time on another project. Most pressure sensors put a signal 4-20mA or 0 - 5V, that is which you can read through an analog input on a data acquisition; measure a 4-20mA signal requires a resistance to convert voltage. Most NI DAQ boards can read a thermocouple on an analog input, but make sure that your hardware is supported reading thermocouples. For an accurate reading, use a device that has the compensation of cold welding integrated - for example, the block connection SCB-68 - and for more accurate measurements, get a Board specifically designed to measure the temperature.

  For measurement of the flow, a standard, simple solution is an orifice plate. You put a transducer for differential pressure across it, seek the appropriate equations and use them to calculate the flow rate given the density of the fluid (which you will be able to calculate from the pressure and the temperature, since the steam tables are widely available). Other differential pressure devices are available as well - at a previous job, we used a double cone of McCrometer. If you call them, they spec for you - but get an approximate cost first to make sure it's in your budget.

• How can I recover my address book from the server, I changed TO?

  I had been with peoplepc.com and changed to another server.  A rep with peoplepc.com said that it exported all my email and my Web mail address book.  He said that I could find on my desktop and export it to where I wanted to.  I don't know how to find. Your help is NEEDED!  Thanks, Chrvenka

  Hello, RJMpcena,

  To see a file/folder named Web Mail on your desktop when Windows loads?  If not, contact peoplepc.com

  http://PSC.PeoplePC.com/articles/PPC/importing-contacts-to-Web-mail.php

• How to change the IP address of the linux server

  Hello
  
  I want to change the IP address of my RHEL 4 server. I use 10.2.0.4 with R12.1.3 E-business and my instance is the only level. I have doc "How change the IP address on a R12 EBusiness Suite Installation [ID 554843.1]" but it could not help me.
  
  
  Thank you
  Krishna

  Salvation;

  Please see below note and links. If you have any questions please update thread:
  How to change IP address in an Oracle Applications environment [ID 553318.1]
  How to change IP on a R12 EBusiness Suite Installation [554843.1 ID]

  See also:
  http://AppsLab.blogspot.com/2009/08/IP-address-change-on-existing-R12.html
  change the IP Address of the server.

  Respect of
  HELIOS

• How to configure the outgoing mail SMTP for Outlook Express 2003 receive service internet ulitizing comcast email?

  My ISP is Comcast.  I use Outlook Express 2003.  Comcast has to change mail outgoing SMTP from 465 to 587, when I could no longer send emails.  I can receive emails, but when I send a mail, Outlook Express says that the email has not been sent (but there are sent) and does not record the email in my sent folder.  I now get 2 copies of every email sent to me.  Help.

  Not surprisingly, Comcast tech told you wrong.
   
   
  Configure Outlook Express for email XFINITY/Comcast
  http://customer.Comcast.com/help-and-support/Internet/configure-Outlook-Express-Xfinity-Internet/
   
   
  Don't forget to set up exactly. Some boxes to check, some do not.
   
   
   
   
   

• How to change the IP address of the EBS Server

  Hello

  I need to change the IP address of the server EBS R12.2.4 mi.

  I only edit the/etc/host file?

  Thank you.

  Luis.

  N °

  You must do several things. Take a look at this document:

  Correct the method of changing the IP address in 11i & R12 (Doc ID 751328.1)

  Kind regards

  Bashar

• How to configure the IKEv2 VPN on Mac OS Server 10.12

  IKEv2 is mentioned in the release notes for Server 5.2 but I can't find instructions anywhere are related.  Anyone know where I could find a tutorial to set up?

  If you are referring to.

  • New IKEv2 authentication method option or specify IPSec disconnect on timeout for VPN

  Then it is a new feature for the profile on Server.app Manager is not a new feature of the VPN on Server.app server. You will need to use a different non-Apple supplied VPN server in order to implement IKEv2.

  Note: as customers El Capitan or later, and iOS 9 or later support IKEv2. (iOS 8 had limited support.)

• How to disable prior authentication logs on to Windows Server 2003

  Hello

  I was wondering if anyone knew a way to disable the prior authentication logs on to a Windows Server 2003 in the Event Viewer, we continue to receive many of these on our replication server that's used to be the PDC, as it is now a secondary to replicate the domain controller until we have completed the migration of all the stuff on the last domain controller. Your help would be greatly appreciated.

  Thank you very much

  RocknRollTim

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• How can I back up Active Directory on Windows Server 2003... ?

  Hello

  I installed the Services Active Directory on my windows Server 2003 and I need to take help if necessary backup...!

  These MS Answers forums are intended for the home rather than the it professional user. Please transfer your question in the relevant Microsoft Technet forum here:

  http://social.technet.microsoft.com/Forums/en-us/category/windowsserver .

  Thank you.      :)

  (I'm sorry, but I can't move this thread for you because the two forums are working on separate platforms)

• How to install 64-bit on a 32-bit Server 2003 print drivers

  Hello

  We are going to deploy Windows 7 64 bit.  We currently have 32-bit Server 2003.  I was able to install half of the 7 64 bit drivers, but spin issues with others.  Universal drivers seem to work.  We organize HP, Xerox and Dell printers.  The error I see is. "The specified driver must be installed remotely from an x 64 Windows XP or Windows server 2003."  I can't make it work.  Any ideas?

  Thank you.

  Hello

  You have reached the end user Microsoft support. The question that you are running in suitable for the forum on the link below.
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer
   
  Let us know if you have other questions about Windows in the future. We will be happy to help you.

• Configuring Web Service access via a Proxy Server?

  Hello
  I'm trying to configure the tool OdiInvokeWebservices to hit a WebService through a proxy server.
  I managed to test my OdiInvokeWebservices against a local WS (i.e. a direct connection), but I do not see how to configure ODI to go through a proxy server.
  There is no obvious configuration setting (I expect to see a proxy host, username, password, and proxy exceptions maybe) on the tool OdiInvokeWebServices or ODI itself.
  
  So, anyone can answer all or part of the following?
  * Are there variables configuration ODI (or ODI environment variables) to set up the proxy server access?
  * In the case of a failure, what is the desirable approach (taking account of the architecture of the ODI)? For example, creating a technology ODI in the topology for HTTP connections through a proxy server (what is a sense - I'm new to ODI)?
  * What is possible or desirable to extend the OdiInvokeWebServices tool to enable the configuration for a proxy server? (probably a bad idea - a lot of hacking involved)?
  
  If all above fails them, then the only option is to give access ODI direct internet access.
  Thanks in advance,
  Matt

  Matt
  Have you tried to add additional parameters to the virtual machine java?
  I see that there are the following options that you can assign to ODI_ADDITIONAL_JAVA_OPTIONS in the odiparams file.
  Java $-Dhttp.proxyHost = proxyhostURL
  -Dhttp.proxyPort = proxyPortNumber
  -Dhttp.proxyUser = someUserName
  -Dhttp.proxyPassword = somePassword javaClassToRun
  Craig