How to control PFI SMU 6556 card?

Similar Questions

• SMU-6556 - how to control the rise in digital lines (hsdio) time

  Hello

  Is it possible to control the rise in digital lines SMU-6556 time?

  Even in a low frequency 10 kHz signal rise time is 2ns.

  TKS,

  Hello engfpe,

  The SMU-6556 is a 50 Ohm system, which means that the output is source series finished to be 50 Ohms and all our cables and accessories are 50 Ohms.  With this configuration, regardless of the flow of data, you should have a clean edge up or down, regardless of the data rate. The quality of the production (edge up or down) on your device is related to the adaptation of impedance of your cables.

  The SMU-6556 cannot adjust the speed of scanning by itself.  However, you can insert simple passive components to do it for you.  I have attached below the images.  The first is a diagram showing a way to slow down the edge.  The second is the a waveform simulation showing the rate of original edge before it slows down and the edge of idle.   This simulation is not the SMU-6556 but rather a generic digital output for concept.  In the schema that R1 is set on 34 Ohms because U1.8 has the 16 additional Ohms on the inside.  TL1 is the output of 50 ohms simulating the cable on the SMU-6556.  R2, R3, and C1 are components, you can insert after the SMU-6556 twist before moving your device/cable.  In this configuration from cable to your device is TL2 which is also 50 ohm, but it could be another impedance in which case you would change R3 to match.

  You can see in the attached images, you can slow down significantly the edge with this configuration by altering the C1.  I hope this helps.

• How can I turn a channel in the SMU-6556 hsdio for material comparison mode?

  Hello

  I am developing a system with Labview2013, TestStand2013, and SMU-6556

  The system diagram is:

  SMU-6556 > - 12 channels - 3---> Dut1

  Hardware compare mode:---3 channels---> Dut2

  | - 3 channels---> Dut3

  | - 3 channels---> Dut4

  In TestStand, I have the following configuration:

  1. in the "Setup" section I'm loading ~ 10 digital waveforms with 12 channels each in memory of SMU-6556.

  2. in the section 'Hand', that I'm running in hardware compare mode each digital waveforms. (DWF1, DWF2,..., DWF10)

  The system works well for test of 4 had.

  Without loading a new wave form how can I enable/disable underwent?

  For example, how can I configure to test only the dut1 and dut3?

  HELO engfpe,

  You can see the advanced, advanced attribute: hardware compare: bit Error Cumulative property and see if that will get your request.

  Cumulative error Bits will tell you what mistakes HWC product channels even if the FIFO is full. In this way, you can at least know where to pass the ASE. If it fails and you would like more information, then you should always charge the waveform in order to get a manageable number of HWC error, but hope that helps at least. This feature was added in NOR-HSDIO 2.0, so make sure you have the latest driver.

• How to set a channel of e/s in the SMU-6556 NI on the ground in PMU mode

  Is there a way or API call in LabVIEW to set one of the channels to the Earth in the SMU-6556 PMU mode?

  If you disconnect the PMU, you will have the option to go to tristate or your digital status before, but not on the ground. Force the 0V is probably the closest you can access a MASS like behavior. The default line is tristate for this camera, that will leave the floating line if there is no active driver.

• Where can I find NEITHER-HSDIO SMU 6556 LabWindows CVI examples?

  Greetings!

  I am looking for examples LabWindows CVI or a help file that shows the function or api calls to control the attributes of progrannable of the HSDIO SMU 6556/6555.

  Ken Grohman

  Hi Ken;

  "' You can find examples for the NOR-HSDIO in the example LabWindows CVI Finder by clicking on help > NOR example Finder and navigate to the material input and output" Modular Instruments ' NOR-HSDIO; "" "" or you can search in Start "all programs" National Instruments "NOR-HSDIO ' examples.

  http://zone.NI.com/reference/en-XX/help/370520J-01/HSDIO/using_ni_hsdio_in_labwindows_cvi/

  Just make sure that when you installed the driver, you have also installed the Application Development Enviroment Support for LabWindows CVI, otherwise the examples will not be there.

  Best regards;

  Pedro Muñoz

• How to control an electric motor using LabVIEW?

  Hello

  is there a simple way to control the rotation speed of an electric motor (12V) using LabVIEW?

  I have an idea how to achieve this using the card OR measurement, its not that cheap. Any ideas?

  Maciek.

  
  

• How to control the length of the field... ?

  Hi all
  
  
  All by providing payment details in the payment.jsp... If we use a credit card which has 16 digits then, how to control the ground to allow the entry of 16 digits only... ?
  
  
  Thank you
  Vishnu

  Write javascript to enter only numbers and set the "16" size = attribute to limit the size to 16 digits.

  JavaScript can be like that of google.

  function isNumberKey (evt) {}
  charCode var = (evt.which)? evt.which: event.keyCode
  If (charCode > 31 & (character code < 48="" ||="" charcode=""> 57))
  Returns false;

  Returns true;
  }

  -Kiss

• How can I remove a credit card on the app store?

  How can I remove a credit card on the app store? I can't download apps because it makes me sign then goes to check and it keeps saying method declined.

  < re-titled by host >

  Click here for an asnwer.

  Change or remove your information from payment of Apple ID - Apple Support

  Hope this helps, good luck to you.

• How can I get a sim card for iphone is without a carrier in order to use wifi

  How can I get a sim card for iPhone is purchased from an apple store with no carrier, I want to load the applications before signing up with someone. Help

  You can access the App Store via your Wi - Fi connection, so no date cell will be used to download apps.

  The only way to get a SIM card is a carrier.

• How can I get the sound card to play on the speakers of the car?

  How can I get the sound card to play on the speakers of the car?

  Usually connecting the phone to the car system - particularly at the point where you can play the music usually connects the Maps app

  There is a switch at the bottom of the maps app with a speaker symbol that allows you to toggle between having the sound coming through the phone or Bluetooth

• HP 2000-2061TU: How can I upgrade my graphic card in my laptop and my model number is hp 2000-2061TU

  How can I update my graphic card in my laptop? and my model number is hp 2000-2061TU

  Please help me...

  Hello
  
  Could you confirm the model name?
  
  It is the following:
  2000 2106TU?
  
  http://support.HP.com/in-en/product/HP-2000-notebook-PC-series/5259209/model/5269792/document/c03454511/
  
  If so, no, you can not - your laptop does no graphics "card", the graph is integrated type Intel Celeron processor.
  
  Manual: http://h10032.www1.hp.com/ctg/Manual/c03308228
  
  Concerning
  
  Visruth

• Satellite M100 with Debian - how to control the power and the cooling fan on

  Hey,.

  I M100 and I installed debian, works very well, but there is a problem.
  Cooling fan turns on the top speed of all time. I m not shy on unix.
  How can I control cooling fan?
  How to control the power to the laptop?

  Hi mate,

  have you ever heard of the toshutils? I highly recommend trying these tools. Just google for toshutils and you'll find a few nice applications. Should usually be included in the distribution you have, also, I would check with 'apt - get search toshutils.

  See you soon

• How to add an additional bank card

  How do you add a new card to your account

  I guess you ask how to add a card to pay Apple.

  Settings > Wallet & Apple pays > add credit or debit card

  If you ask about adding a map to your Apple ID / iTunes, then you can have only one card at a time is recorded.

• How to control the speed of the fan on Satellite A660 - 11 M?

  Please any body know how to control the fan speed its always of 69% and making bad noise and the cpu use is 3% no to treatment high I try avancΘs power but still runing high speed

  Advanced power settings go to Toshiba power Saver saver > cooling method. There are minimum level. Change back to your power management for a second power plan, and the fan must be much quieter.

  I did it on my Satellite A660.
  Before changing PC Toshiba, health monitor showed CPU temperature 41% and the speed of the fan was 67%. After changing the method of cooling fan speed is 0%.

• How can I unredeem my iTunes card

  How can I unredeem my itunes card so I can use it on another account

  Click here and ask the staff of the iTunes Store for the balance on the card. they will do only that if none of it has been spent.

  (137673)