How to control the output voltage?

Similar Questions

• How to configure the outputs voltage NI 9477

  Hello

  I'm trying to control a motor using a cRIO 9074 with the NI 9477 module. I would like to configure the output voltage of the module and if I understand correctly, they vary between 5 to 60 v.

  How can I have a 24 v output?

  Thank you.

  JaneDoe94 wrote:

  So if I understand correctly, I can use an exit as a switch?

  If I choose resistance pull-up so the current stay under 1A, would this work?

  For example, I am using R = 20 kOhm and DC = 24V. I need to stay below 5mA current.

  9477 module is basically a relay to connect to the Earth.  But beware of your voltage and current limits.  The maximum current that can flow is 0.625 A by line.  So make sure that you stay below that.

• How the output voltage is coded on 16 bits DAQmx devices?

  In our laboratory, we have two devices DAQmx, the NOR-PCIe-6363 and the NOR-PCI-6733. Both have 16-bit for bipolar analog output precision. I understand that the small voltage difference that can be made is 2 * Vref/2 ^ 16, where Vref is the reference AO voltage (10 Volts or externally provided for 6733, 10 or 5 Volts or externally supplied for the 6363).

  I wanted to know how the output voltage is coded. DAQmx functions take 64 bit floats as input, and at some point, they must have their reduced accuracy. How is this done rounding, is a floating point around the nearest possible tension, or is always rounded down or always rounded upward?

  What is all the possible output voltages? Some diagrams in NOR-DAQmx help/measurement Fundamentals, signals, Analog, sampling considerations seem like they could involve the maximum voltage + Vref is not achievable, so I think that is all of the possible tensions - Vref + 2 * Vref * n/2 ^ 16, with n ranging from 0 to 2 ^ 16-1 included. This includes - Vref and does not zero but + Vref.

  Could I get confirmation on this point, or be corrected if it is wrong?

  Hi Chris,

  The scale of writing DAQmx version performs double floating precision scaling and then he made a turn, the closest to convert the resulting code of the DAC to double int16_t (or uint16_t for unipolar devices). Floating point scale includes the custom scale AO if you have configured one, the conversion of volts or AMPS to the codes of the DAC and for some devices, the calibration scale.

  You can check the coefficients of scaling using the AO. Property of DevScalingCoeff. It takes V / A-> CAD codes and scaling into account calibration, but not the scales to customized AO.

  The PCIe-6363 X series devices preset scaling in software. The internal reference of the AO is slightly higher than 10V, to correct the errors of gain and offset does not limit the output range. It also means that you are not limited to 9.9997 V on this device when you are using an internal reference.

  The PCI-6733 uses calibration DAC instead of software scaling. RAW - 32768 means - 10 V, 0 corresponds to 0 V, 32768 is impossible because of two of the 16 bits of the add-in and 32767 translates 9.9997 V. When you continue 10 V to write DAQmx with this device, DAQmx he forced into 9.9997 V.

  Note that for these two devices, the absolute accuracy full scale includes over 305 uV of error. Look at the tables of absolute precision AO in the specs of the device for the full story.

  Brad

• DAQmx how to control the level of tension AO paused for a relaxing break?

  I have an application where I need to generate a waveform of a fixed frequency (~ 200 kHz) and the amplitude, but for differing them burst lengths and different lengths of time between bursts. These bursts and these delays are controlled by a line of DIO to generate the relaxing break. I also need to have the output voltage analog voltage controlled between bursts of waveform. I explored using various trigger options, the break seems to be the best solution, but I'm difficult to control the particular point of the end of the waveform during the break occurs to make sure that the break is at the same specific voltage when the wave is hidden. I try to adjust the position of the example 'Analog output Pause for the periodic Signal with regeneration on specimen' but cannot get regular tension during the break I'm after. I use a card Series DAQ. X is there a simple way to pre-set the tension that will be broadcast during the paused state when using a relaxing break? I was not able to find it in the examples or documents. I can't use the code of reference AO set example because it is a software-driven and does not fit into the model of schedule I need to generate.

  Hello

  I don't think there is a way to establish a certain level on the analog output, based on a relaxing break.  I watch using a redeclenchables task analog output and do every hour of beginning to the required voltage.

• Satellite M100 with Debian - how to control the power and the cooling fan on

  Hey,.

  I M100 and I installed debian, works very well, but there is a problem.
  Cooling fan turns on the top speed of all time. I m not shy on unix.
  How can I control cooling fan?
  How to control the power to the laptop?

  Hi mate,

  have you ever heard of the toshutils? I highly recommend trying these tools. Just google for toshutils and you'll find a few nice applications. Should usually be included in the distribution you have, also, I would check with 'apt - get search toshutils.

  See you soon

• How to control the speed of the fan on Satellite A660 - 11 M?

  Please any body know how to control the fan speed its always of 69% and making bad noise and the cpu use is 3% no to treatment high I try avancΘs power but still runing high speed

  Advanced power settings go to Toshiba power Saver saver > cooling method. There are minimum level. Change back to your power management for a second power plan, and the fan must be much quieter.

  I did it on my Satellite A660.
  Before changing PC Toshiba, health monitor showed CPU temperature 41% and the speed of the fan was 67%. After changing the method of cooling fan speed is 0%.

• How to control the ws appeal period

  Hi Experts,

  I use bpm12.1.3, when the process web service using the service task, how to control the delay?

  Best regards

  Hi user,

  There is a nice blog on wait times. It's about 11g, but it also applies to 12 c.

  https://technology.AMIS.nl/2011/11/18/timeouts-in-Oracle-SOA-Suite-11g/

  Antonis

• How to control the movement of the oam in muse & just play once the proposal?

  How to control the movement of the oam in muse & just play once the proposal?

  This must be configured during the creation of the oam, no Muse, but the animated application you use.

  Thank you

  Sanjit

• How to install the output in bridge CC module using an apple OSX 10.9.5 and a miss apple OSX 10.11 this point completely in CC bridge!

  How to install the output in bridge CC module using an apple OSX 10.9.5 and a miss apple OSX 10.11 this point completely in CC bridge!

  Hi abev41080082

  Greetings.

  • Please visit this link and follow the instructions
    • https://helpx.Adobe.com/bridge/KB/install-output-module-bridge-cc.html
    • Output Module (bridge CC) works only on Mac

  Concerning

  Rohit

• How to make the output of the task are an entry in another task

  How to connect the output of a task for I can use it as input for another task?  See this screen below: the task "Invoke the Script" run a PowerShell Script.  The task 'Send E-mail' send an email.  The two tasks work separately.  How can I get the results of my powerShell script that I can use them as content of the task 'Send Email'?

  

  On the script invoke task you set the attributes of output containing the results of powershell.

  to do this, select the output tab and use an object name that was put in place in powershell results as in the data

  You may need to format, this results in a recognized VMware object I guess in your case it is a string type.

  and then select the e-mail task, select the task from email, click on the small eye looking for icon "view details".

  Select the Visual link

  Select the attributes you setup from the output of the previous task and hang it in the input parameters of the task to email.

  fact

• How to control the length of the field... ?

  Hi all
  
  
  All by providing payment details in the payment.jsp... If we use a credit card which has 16 digits then, how to control the ground to allow the entry of 16 digits only... ?
  
  
  Thank you
  Vishnu

  Write javascript to enter only numbers and set the "16" size = attribute to limit the size to 16 digits.

  JavaScript can be like that of google.

  function isNumberKey (evt) {}
  charCode var = (evt.which)? evt.which: event.keyCode
  If (charCode > 31 & (character code < 48="" ||="" charcode=""> 57))
  Returns false;

  Returns true;
  }

  -Kiss

• How to control the length of field, select items list to 4.2 page

  I apologize in advance if I ask what is obvious, but simply, I couldn't get a response yet:
  
  I would like to know how to control the length of the elements of the type selection list page 4.2
  (as for a normal textfield: in the case where the content is longer than simply not all appears on the screen)
  
  help much appreciated
  see you soon
  Wim

  WimDeGroot wrote:
  I apologize in advance if I ask what is obvious, but simply, I couldn't get a response yet:

  I would like to know how to control the length of the elements of the type selection list page 4.2
  (as for a normal textfield: in the case where the content is longer than simply not all appears on the screen)

  Normally the browser automatically resizes the selection list based on the content.

  What version of the browser / do you use?

  What theme?

  What model page/region?

  What form/article layout?

  What content does not match?

  (Basically the best way to get help with problems of this type is to reproduce on apex.oracle.com and see us actually...)

• How to control the service console in ESX?

  How to control the service console in ESX?

  http://www.Petri.co.il/5-critical-VMware-ESX-CLI-network-commands.htm

  http://download3.VMware.com/VMworld/2006/mdc9694.PDF

  http://download3.VMware.com/VMworld/2006/mdc9807.PDF

  http://download3.VMware.com/VMworld/2006/tac0028.PDF

  http://download3.VMware.com/VMworld/2006/tac9689-b.PDF

  http://download3.VMware.com/VMworld/2006/labs2006/VMworld.06.Lab04-performance-manual.PDF

  http://www.RTFM-ed.co.UK/

  PS: If you have found useful messages then please leave a few points

  André

• How to control the number of fields in the Advanced mode in &lt; af:query &gt;

  Hello
  
  How to control the number of fields in the Advanced mode in < af:query >?
  
  Say I have 20 fields in my table, and I created a view of criteria with 2 fields. This would work perfectly in basic mode. But in Advanced mode , the choice of fields is possible by clicking on the Add fields button. I didn't have the customer to search with all 20 fields. Only 10 fields must be listed in the Advanced Mode, even if there are 20 fields in my table.
  
  How can I control the list of fields in ADDFields button?
  
  Any ideas?
  
  
  
  KR

  You can uncheck the contestable ownership of attributes that you must not appear in the Advanced Mode (but they will not appear in the other modes too!) or by programming the value the same as those mentioned here.

  http://adfcodebits.blogspot.com/2010/11/bit-27-setting-view-object-attributes.html

  Also, you can hide the button AddFields as suggested here - http://www.notjustjava.com/2011/12/cool-tips-to-showhide-components-of-the-query-control-of-adf/

• How to control the sort during the download or export

  can't figure out how to control the sort order when you export on hard drive or upload to smugmug.  have photos arranged in the way I want to do in LR and then when I export to hard drive they are ordered by file name.

  When it comes to your hard drive, your operating system determines the file order.  No matter what you do in Lightroom, the OS will be based on your choice determin how files will be ordered. If you want them to be in order, you should probably adopt a convention of name change in your export that names the exported files similarly followed by a sequence number.  File01, folder 02, etc. Then set your viewer (Finder/Explorer) to sort by file name in ascending order.