How to create a VPN Tunnel

Similar Questions

• How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Dear all

  How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Concerning

  Hi Imran,

  Can't do much about that because it depends on what authenticate you the VPN server and how the settings. But let me introduce you to the memory layout. Once you install and open a VPN client. Press it again and it opens up a new page for the VPN config.

  Example of configuration as it is attached. But it differs depending on the configuration of your vpn server.

  Once you create and save this profile. Your FCP file is stored.

  Please assess whether the information provided is useful.

  By

  Knockaert

• Creating a VPN Tunnel without RFC1918 subnets

  Hi all

  I was prompted to configure a Cisco router to one of our partners using a method with which I am familiar. That is why I hope someone here can guide me in the right direction. Essentially the establishment should be like this:

  At one end there is a firewall with an IP address of 123.123.123.1 (all wrong FT). This must be the VPN endpoint. Behind this firewall is a server with a private IP 172.16.1.1. This private IP address is NAT due 123.123.123.2.

  Now at the other end is a VPN router with an IP address of 234.234.234.1. It is another VPN endpoint. There is another internal server with the IP 10.0.0.1. I don't want to create an external NAT for this IP address that is internal if possible.

  Essentially, I need to get 172.16.1.1 and 10.0.0.1 to communicate with each other via a VPN, but NOT to use their IP addresses in the VPN tunnel.

  What is the best way to achieve this? Any help would be appreciated!

  Craig

  This configuration should do the trick for you...

• How to create a vpn connection

  I know that this discussion has already been posted long ago, but please help me to make this thing work. I have an assignment topic security [in which my subject are vpn] and have a presentation must undergo. I want to create a server vpn on my laptop running windows 7 and my partner's cell phone running windows 8, join. is it possible to do? Please help me through all the steps I tried this on my own using all the steps provided on the internet but ended up with my laptop friends fail to connect. Thanks in advance to the contributors of this community to guide me.

  Hi Alex,

  Welcome to the Microsoft Community Forum.

  I understand that you have a problem with setting up VPN between two computers.

  Unfortunately, the issue you have mentioned on here is best suited for the Microsoft TechNet community, so I suggest you the same post in the Microsoft TechNet forum for further assistance on this issue.

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Thank you

• How to create a SSH tunnel connection to an Instance of Cloud? in 4.1.0.18.37 tab SSH for the connection dialog does not appear.

  The Help window is NOT so useful.  I use windows 7. In SQL DEV 4.0, I was able to connect to an instance of cloud without start Putty and the implementation of tunneling.

  View > SSH

  Create a SSH Host

  In the connection dialog box, set your SSH connection type

  Select your SSH host from the dropdown list control of tunnel on the connection properties

  The aid is in beta, all as the product

• How to create vpn with vista home premium on basis of vpn xp settings?

  I can connect to the vpn with xp machine, but when I try to imitate xp setting with machine to vista Home premium I can't connect to the same vpn. What do you suggest me?

  How to create a vpn connection in Vista: http://techrepublic.com.com/2346-1035_11-61437-1.html?tag=content;leftCol.  NOTE: I don't know what you mean "based" vpn xp settings, but you will have to do the best you can with the options and settings available in Vista (that I n "' t know how they compare to XP, but I hope that you will be able to do so because).

  Here is another article on the procedure: http://www.publicvpn.com/support/Vista.php.

  Here is an article on how configure a VPN with an ISP in Vista: http://www.web-articles.info/e/a/title/How-to-create-a-VPN-connection-over-your-ISP-connection/.

  Here is an article with a number of different other items all on vpn in Vista (I don't know exactly what type of configuration you "AVIC - as a host, as a customer, on what type of connection,--but this article covers many different aspects and I hope that at least a couple will be a help for you: http://compnetworking.about.com/od/vpnsetup/VPN_Setup_How_to_Set_Up_a_VPN.htm.)

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• VPN tunnel with only one authorized service

  Hello

  has got a pix 520 with V 6.22. Now, I created a VPN Tunnel from our server to a

  annother company server and I only want to have ssh connection. If it works

  pretty good - but the other host, it is possible to connect on our host by

  ICMP, ftp, telnet... How can I manage configured my pix to refuse all this

  services?

  Here is my configuration:

  name 10.x.x.x ffmz1_is

  name 212.x.x.x conliner_os

  conliner_ssh name 192.168.0.250

  object-group network conliner

  object-network 192.168.0.0 255.255.255.0

  access list on the inside to allow icmp host ffmz1_is a

  access-list inside permit TCP host ffmz1_is any ftp eq

  access-list inside allow host ffmz1_is udp any eq smtp

  access-list inside allow host ffmz1_is host conliner_ssh eq ssh tcp

  no_nat list of allowed access host ip conliner object-group ffmz1_is

  access-list allowed conliner host ip conliner object-group ffmz1_is

  ...

  crypto VPN 30 card matches the address conliner

  card crypto VPN 30 set peer conliner_os

  ...

  Thank you very much

  The sole purpose of "ipsec sysopt connection permit" is to allow traffic through a tunnel to bypass access-groups. It is not necessary to use it, but then you must explicitly allow traffic you want through your access list.

  The command is very useful when you need to establish a vpn using the cisco customer remotely. Because you must use dynamic crypto maps and you don't know the IP address of the peer, if you didn't have the sysopt command, you will need to allow traffic from an source.

  And you don't have to open all ports for the PIX to be able to establish the tunnel with its ipsec peer.

  You need to allow udp 500 and protocol 50-51 when ipsec traffic through your firewall. Let's say you have another PIX inside who wants to establish a vpn on your main PIX with a third PIX on the outside, you must open the ports in your main PIX.

• FAILURE OF VPN TUNNEL

  Hello guys,.

  I have an ASA 5505 firewall tries to create a VPN tunnel from site to site with a router of 2621 running Advanced IP services. The tunnel keeps do not and I don't know why. Below is the config.

  !
  hostname SeCuReWaLL
  domain default.domain.invalid
  activate 2KFQnbNIdI.2KYOU encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  name 192.168.2.0 outside
  name 192.168.3.0 inside
  !
  interface Vlan1
  Description of network links extended to outside of the
  nameif outside
  security-level 0
  192.168.2.101 IP address 255.255.255.0
  !
  interface Vlan2
  Description within a private network
  nameif inside
  security-level 100
  address 192.168.3.1 IP 255.255.255.0
  !
  interface Ethernet0/0
  !
  interface Ethernet0/1
  switchport access vlan 2
  !
  interface Ethernet0/2
  Shutdown
  !
  interface Ethernet0/3
  Shutdown
  !
  interface Ethernet0/4
  Shutdown
  !
  interface Ethernet0/5
  Shutdown
  !
  interface Ethernet0/6
  Shutdown
  !
  interface Ethernet0/7
  Shutdown
  !
  boot system Disk0: / asa822 - k8.bin
  passive FTP mode
  DNS server-group DefaultDNS
  domain default.domain.invalid
  allow inside_access_in to access extended list ip inside outside 255.255.255.0 255.255.255.0
  outside_access_in list extended access permit icmp any any echo response
  site_router to access extended list ip inside 255.255.255.0 allow 192.168.5.0 255.255.255.0
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 625.bin
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access site_router
  NAT (inside) 1 inside 255.255.255.0
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 192.168.2.1 1
  Outdoor 192.168.5.0 255.255.255.0 192.168.2.107 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  HTTP inside 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac secure_set
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  peer set card crypto ipsec_map 10 192.168.2.107
  card crypto ipsec_map 10 transform-set secure_set
  ipsec_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  md5 hash
  Group 5
  lifetime 28800
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  dhcpd dns 192.168.2.1
  !
  dhcpd address 192.168.3.10 - 192.168.3.40 inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
  tunnel-group 192.168.2.107 type ipsec-l2l
  IPSec-attributes tunnel-group 192.168.2.107
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:a6ffc4e9572dbee8e526c3013a96a510
  : end

  !
  InternetRouter hostname
  !
  boot-start-marker
  boot-end-marker
  !
  !
  No aaa new-model
  no location network-clock-participate 1
  No network-clock-participate wic 0
  IP cef
  !
  !
  !
  !
  no ip domain search
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  crypto ISAKMP policy 10
  BA 3des
  md5 hash
  preshared authentication
  Group 5
  lifetime 28800
  key cisco address 192.168.2.101 crypto ISAKMP xauth No.
  !
  !
  Crypto ipsec transform-set esp-3des secure_set
  !
  ipsec_map 10 ipsec-isakmp crypto map
  defined peer 192.168.2.101
  Set transform-set secure_set
  match the address router_site
  !
  !
  !
  !
  interface Loopback0
  192.168.5.1 IP address 255.255.255.0
  !
  interface FastEthernet0/0
  IP 192.168.2.107 255.255.255.0
  automatic duplex
  automatic speed
  ipsec_map card crypto
  !
  interface Serial0/0
  no ip address
  Shutdown
  !
  interface FastEthernet0/1
  no ip address
  Shutdown
  automatic duplex
  automatic speed
  !
  interface Serial0/1
  no ip address
  Shutdown
  !
  IP route 192.168.3.0 255.255.255.0 192.168.2.101
  !
  !
  IP http server
  no ip http secure server
  !
  router_site extended IP access list
  ip licensing 192.168.5.0 0.0.0.255 192.168.3.0 0.0.0.255
  !
  !
  !
  !
  control plan
  !
  !
  !
  Voice-port 1/0/0
  !
  Voice-port 1/0/1
  !
  Voice-port 1/1/0
  !
  Voice-port 1/1/1
  !
  !
  !
  !
  !
  !
  !
  !
  Line con 0
  exec-timeout 0 0
  Synchronous recording
  line to 0
  line vty 0 4
  opening of session
  !
  !
  end

  InternetRouter #debug isakmp crypto
  Crypto ISAKMP debug is on
  InternetRouter #ping
  Protocol [ip]:
  Target IP address: 192.168.3.10
  Number of repetitions [5]:
  Size of datagram [100]:
  Timeout in seconds [2]:
  Extended commands [n]: y
  Address source or interface: 192.168.5.1
  Type of service [0]:
  Set the DF bit in the IP header? [None]:
  Validate the response data? [None]:
  Data model [0xABCD]:
  In bulk, Strict, Record, Timestamp, Verbose [no]:
  Scan the range of sizes [n]:
  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 192.168.3.10, time-out is 2 seconds:
  Packet sent with the address source 192.168.5.1

  * 01:49:47.699 Mar 1: ISAKMP: ke received message (1/1)
  * 01:49:47.699 Mar 1: ISAKMP: (0:0:N / A:0): THE application profile is (NULL)
  * 01:49:47.699 Mar 1: ISAKMP: created a struct peer 192.168.2.101, peer port 500
  * 01:49:47.699 Mar 1: ISAKMP: new created position = 0x8553C778 peer_handle = 0 x 80000013
  * 01:49:47.699 Mar 1: ISAKMP: lock struct 0x8553C778, refcount IKE peer 1 for isakmp_initiator
  * 01:49:47.699 Mar 1: ISAKMP: 500 local port, remote port 500
  * 01:49:47.699 Mar 1: ISAKMP: set new node 0 to QM_IDLE
  * 01:49:47.703 Mar 1: insert his with his 84074CC8 = success
  * 01:49:47.703 Mar 1: ISAKMP: (0:0:N / A:0): cannot start aggressive mode, try the main mode.
  * 01:49:47.703 Mar 1: ISAKMP: (0:0:N / A:0): found peer pre-shared key matching 192.168.2.101
  * 01:49:47.703 Mar 1: ISAKMP: (0:0:N / A:0): built the seller-07 ID NAT - t
  * 01:49:47.703 Mar 1: ISAKMP: (0:0:N / A:0): built of NAT - T of the seller-03 ID
  * 01:49:47.703 Mar 1: ISAKMP: (0:0:N / A:0): built the seller-02 ID NAT - t
  * 01:49:47.703 Mar 1: ISAKMP: (0:0:N / A:0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
  * 01:49:47.707 Mar 1: ISAKMP: (0:0:N / A:0): former State = new State IKE_READY = IKE_I_MM1

  * 01:49:47.707 Mar 1: ISAKMP: (0:0:N / A:0): early changes of Main Mode
  * 01:49:47.707 Mar 1: ISAKMP: (0:0:N / A:0): send package to 192.168.2.101 my_port 500 peer_port 500 (I) MM_NO_STATE
  * 01:49:47.711 Mar 1: ISAKMP (0:0): packet received 192.168.2.101 dport 500 sport Global 500 (I) MM_NO_STATE
  * 01:49:47.711 Mar 1: ISAKMP: (0:0:N / A:0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
  * 01:49:47.711 Mar 1: ISAKMP: (0:0:N / A:0): former State = new State IKE_I_MM1 = IKE_I_MM2

  * 01:49:47.715 Mar 1: ISAKMP: (0:0:N / A:0): treatment ITS payload. Message ID = 0
  * 01:49:47.715 Mar 1: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment
  * 01:49:47.715 Mar 1: ISAKMP: (0:0:N / A:0): supplier code seems the unit/DPD but major incompatibilite.123
  * 01:49:47.715 Mar 1: ISAKMP: (0:0:N / A:0): provider ID is NAT - T v2
  * 01:49:47.719 Mar 1: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment
  * 01:49:47.719 Mar 1: ISAKMP: (0:0:N / A:0): supplier code seems the unit/DPD but major incompatibility of 194
  * 01:49:47.719 Mar 1: ISAKMP: (0:0:N / A:0): found peer pre-shared key matching 192.168.2.101
  * 01:49:47.719 Mar 1: ISAKMP: (0:0:N / A:0): pre-shared key local found
  * 01:49:47.719 Mar 1: ISAKMP: analysis of the profiles for xauth...
  * 01:49:47.719 Mar 1: ISAKMP: (0:0:N / A:0): audit ISAKMP transform 1 against the policy of priority 10
  * 01:49:47.719 Mar 1: ISAKMP: 3DES-CBC encryption
  * 01:49:47.719 Mar 1: ISAKMP: MD5 hash
  * 01:49:47.719 Mar 1: ISAKMP: group by default 5
  * 01:49:47.719 Mar 1: ISAKMP: pre-shared key auth
  * 01:49:47.723 Mar 1: ISAKMP: type of life in seconds
  * 01:49:47.723 Mar 1: ISAKMP: life (basic) of 28800
  * 01:49:47.723 Mar 1: ISAKMP: (0:0:N / A:0): atts are acceptable. Next payload is 0
  * 1 Mar 01:49:48.119: ISAKMP:(0:1:SW:1): load useful vendor id of treatment
  * 1 Mar 01:49:48.119: ISAKMP:(0:1:SW:1): vendor ID seems the unit/DPD but major incompatibility of 123
  * 1 Mar 01:49:48.123: ISAKMP:(0:1:SW:1): vendor ID is NAT - T v2
  * 1 Mar 01:49:48.123: ISAKMP:(0:1:SW:1): load useful vendor id of treatment
  * 1 Mar 01:49:48.123: ISAKMP:(0:1:SW:1): vendor ID seems the unit/DPD but major incompatibility of 194
  * 01:49:48.123 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
  * 01:49:48.123 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_I_MM2 = IKE_I_MM2

  * 1 Mar 01:49:48.127: ISAKMP:(0:1:SW:1): sending package to 192.168.2.101 my_port 500 peer_port 500 (I) MM_SA_SETUP
  * 01:49:48.127 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
  * 01:49:.48.131 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_I_MM2 = IKE_I_MM3

  * 01:49:48.383 Mar 1: ISAKMP (0:134217729): packet received 192.168.2.101 dport 500 sport Global 500 (I) MM_SA_SETUP
  * 01:49:48.383 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
  * 01:49:48.383 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_I_MM3 = IKE_I_MM4

  * 1 Mar 01:49:48.387: ISAKMP:(0:1:SW:1): processing KE payload. Message ID = 0
  * 1 Mar 01:49:48.887: ISAKMP:(0:1:SW:1): processing NONCE payload. Message ID = 0
  * 01:49:48.887 Mar 1: ISAKMP: (0:1:SW:1): found peer pre-shared key matching 192.168.2.101
  * 01:49:48.891 Mar 1: ISAKMP: (0:1:SW:1): SKEYID generated State
  * 1 Mar 01:49:48.891: ISAKMP:(0:1:SW:1): load useful vendor id of treatment
  * 1 Mar 01:49:48.891: ISAKMP:(0:1:SW:1): vendor ID is the unit
  * 1 Mar 01:49:48.891: ISAKMP:(0:1:SW:1): load useful vendor id of treatment
  * 1 Mar 01:49:48.891: ISAKMP:(0:1:SW:1): vendor ID seems the unit/DPD but major incompatibility of 145
  * 1 Mar 01:49:48.891: ISAKMP:(0:1:SW:1): vendor ID is XAUTH
  * 1 Mar 01:49:48.895: ISAKMP:(0:1:SW:1): load useful vendor id of treatment
  * 1 Mar 01:49:48.895: ISAKMP:(0:1:SW:1): speaking to another box of IOS!
  * 1 Mar 01:49:48.895: ISAKMP:(0:1:SW:1): load useful vendor id of treatment
  * 01:49:48.895 Mar 1: ISAKMP: (0:1:SW:1): supplier code seems the unit/DPD but hash mismatch
  * 01:49:48.895 Mar 1: ISAKMP: receives the payload type 20
  * 01:49:48.895 Mar 1: ISAKMP: receives the payload type 20
  * 01:49:48.895 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
  * 01:49:48.899 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_I_MM4 = IKE_I_MM4

  * 01:49:48.899 Mar 1: ISAKMP: (0:1:SW:1): send initial contact
  * 01:49:48.899 Mar 1: ISAKMP: (0:1:SW:1): ITS been pr.e using id ID_IPV4_ADDR type shared-key authentication
  * 01:49:48.899 Mar 1: ISAKMP (0:134217729): payload ID
  next payload: 8
  type: 1
  address: 192.168.2.107
  Protocol: 17
  Port: 500
  Length: 12
  * 01:49:48.903 Mar 1: ISAKMP: (0:1:SW:1): the total payload length: 12
  * 1 Mar 01:49:48.903: ISAKMP:(0:1:SW:1): sending package to 192.168.2.101 my_port 500 peer_port 500 (I) MM_KEY_EXCH
  * 01:49:48.907 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
  * 01:49:48.907 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_I_MM4 = IKE_I_MM5

  * 01:49:48.907 Mar 1: ISAKMP (0:134217729): packet received 192.168.2.101 dport 500 sport Global 500 (I) MM_KEY_EXCH
  * 1 Mar 01:49:48.911: ISAKMP:(0:1:SW:1): payload ID for treatment. Message ID = 0
  * 01:49:48.911 Mar 1: ISAKMP (0:134217729): payload ID
  next payload: 8
  type: 1
  address: 192.168.2.101
  Protocol: 17
  Port: 0
  Length: 12
  * 1 Mar 01:49:48.911: ISAKMP:(0:1:SW:1): peer games * no * profiles
  * 1 Mar 01:49:48.911: ISAKMP:(0:1:SW:1): HASH payload processing. Message ID = 0
  * 01:49:48.915 Mar 1: ISAKMP: received payload type 17
  * 1 Mar 01:49:48.915: ISAKMP:(0:1:SW:1): load useful vendor id of treatment
  * 1 Mar 01:49:48.915: ISAKMP:(0:1:SW:1): vendor ID is DPD
  * 01:49:48.915 Mar 1: ISAKMP: (0:1:SW:1): SA authentication status:
  authenticated
  * 01:49:48.915 Mar 1: ISAKMP: (0:1:SW:1): SA has been authenticated with 192.168.2.101
  * 01:49:48.915 Mar 1: ISAKMP: attempts to insert a 192.168.2.107/192.168.2.101/500/ peer and inserted 8553 778 successfully.
  * 01:49:48.919 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
  * 01:49:48.919 Mar 1: ISAKMP: (0:1:SW:1.): O State of LD = new State IKE_I_MM5 = IKE_I_MM6

  * 01:49:48.919 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
  * 01:49:48.919 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_I_MM6 = IKE_I_MM6

  * 01:49:48.923 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
  * 01:49:48.923 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_I_MM6 = IKE_P1_COMPLETE

  * 01:49:48.927 Mar 1: ISAKMP: (0:1:SW:1): start Quick Mode Exchange, M - ID of 590019425
  * 1 Mar 01:49:48.931: ISAKMP:(0:1:SW:1): sending package to 192.168.2.101 my_port 500 peer_port 500 (I) QM_IDLE
  * 01:49:48.931 Mar 1: ISAKMP: (0:1:SW:1): entrance, node-590019425 = IKE_MESG_INTERNAL, IKE_INIT_QM
  * 01:49:48.931 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_QM_READY = IKE_QM_I_QM1
  * 01:49:48.931 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
  * 01:49:48.935 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE

  * 01:49:48.939 Mar 1: ISAKMP (0:134217729): packet received 192.168.2.101 dport 500 sport Global 500 (I) QM_IDLE
  * 01:49:48.939 Mar 1: ISAKMP: node set 330122531 to QM_IDLE
  * 1 Mar 01:49:48.943: ISAKMP:(0:1:SW:1): HASH payload processing. Message ID = 330122531
  * 1 Mar 01:49:48.943: ISAKMP:(0:1:SW:1): treatment protocol NOTIFIER INVALID_ID_INFO 1
  0, message ID SPI = 330122531, a = 84074CC8
  * 01:49:48.943 Mar 1: ISAKMP: (0:1:SW:1): the peer is not paranoid KeepAlive.

  * 01:49:48.943 Mar 1: ISAKMP: (0:1:SW:1): remove the reason for HIS "fatal Recevied of information' State (I) QM_IDLE (ext. 192.168.2.101)
  * 01:49:48.943 Mar 1: ISAKMP: (0:1:SW:1): remove error node 330122531 FALSE reason 'informational (en) st.
  Success rate is 0% (0/5)
  InternetRouter #ate 1 "
  * 01:49:48.943 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
  * 01:49:48.947 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE

  * 01:49:48.947 Mar 1: ISAKMP (0:134217729): packet received 192.168.2.101 dport 500 sport Global 500 (I) QM_IDLE
  * 01:49:48.951 Mar 1: ISAKMP: node set-412204705 to QM_IDLE
  * 1 Mar 01:49:48.951: ISAKMP:(0:1:SW:1): sending package to 192.168.2.101 my_port 500 peer_port 500 (I) QM_IDLE
  * 01:49:48.951 Mar 1: ISAKMP: (0:1:SW:1): purge the node-412204705
  * 01:49:48.955 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
  * 01:49:48.955 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_P1_COMPLETE = IKE_DEST_SA

  * 01:49:48.955 Mar 1: ISAKMP: (0:1:SW:1): removal of HIS State "No reason" why (I) QM_IDLE (ext. 192.168.2.101)
  * 01:49:48.955 Mar 1: ISAKMP: Unlocking IKE struct 0x8553C778 for isadb_mark_sa_deleted(), count 0
  * 01:49:48.959 Mar 1: ISAKMP: delete peer node by peer_reap for 192.168.2.101: 8553 778
  * 01:49:48.959 Mar 1: ISAKMP: (0:1:SW:1): error in node-590019425 FALSE reason for deletion "deleted IKE."
  * 01:49:48.959 Mar 1: ISAKMP: (0:1:SW:1): node error 330122531 FALSE reason for deletion "removed IKE."
  * 01:49:48.959 Mar 1: ISAKMP: (0:1:SW:1): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
  * 01:49:48.959 Mar 1: ISAKMP: (0:1:SW:1): former State = new State IKE_DEST_SA = IKE_DEST_SA

  Hello

  I gave a quick scan here for the configuration on both devices, found two or three commands are missing from the configuration of the ASA

  ASA
  ---

  card crypto ipsec_map 10 correspondence address site_router

  outside_access_in list extended access udp allowed any any eq 500
  outside_access_in list extended access udp allowed any any eq 4500
  outside_access_in list extended access allow esp a whole

  I'm assuming pre shared key defined on ASA cisco is the same on router

  On router
  ---------

  Try running the following commands: -.

  No crypto ipsec transform-set esp-3des secure_set
  Crypto ipsec transform-set esp-3des esp-sha-hmac secure_set

  At the time of the opening of the tunnel, please gather at the debug crypto isa 127 output and debug crypto ipsec 127 of ASA

  You can also check the configuration below document link

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805e8c80.shtml

  Ignore the map route on router configuration contained in the above document *.

  HTH...

  Kind regards
  Mohit

• How to change an existing in ASDM VPN tunnel?

  I currently have a VPN tunnel together upwards, but to change some of the configurations as making ikev2, replacing the SHA512 hash and change it in the DH group 14. I intend to do this in ASDM. I already created a group of tunnel ikev2 that I put the tunnel and created a Card Crypto that is configured with the right proposal ikev2 IPSec and Diffie-Hellman group. All other configurations such as the IP of Peer address and subnets configured and I'll work with the engineers at the other end of the tunnel to ensure that configurations are, I want to just make sure I'm not missing anything. Someone at - he never comes to change the configuration of an existing ASDM so tunnel, and it worked correctly? Here are the steps that I have will be taken as well as those I've already mentioned:

  -Edit the connection profile so that the name of group policy use the correct tunnel that was created for ikev2

  -Enter the pre-shared key local and remote pre-shared key ikev2 tab

  -Change the IKE Policy so that it uses the ikev2 policy that was created to use SHA512

  -Modify the IPSEC proposal so that it uses AES256-SHA512

  -THE CRYPTO MAP IS ALREADY CREATED

  -Change the secret of transfer perfect in group 14

  Hello

  Let me go through your questions to clarify this double:

  1. If I have a Crypto map applied to my external interface with a proposal of IPSec of ikev1 can I just add a proposal ikev2 in this Crypto map as well?

  If you have a card encryption applied to different peers outside and 3 with different order number, you will need to replace the proposal for the peer using IKEv2: IKEv2 IKEv1, the others must continue to use their IKEv1 IPSec proposal.

  2. so can I add an ikev2 with AES256 SHA512 hash proposal to my 123.123.123.456 tunnel group and continue to have all three tunnel groups always pass traffic? What happens if I add the proposal ikev2, but REMOVE the ikev1 this group of tunnel proposal because I don't want this group of tunnel use one other than AES256-SHA512 hash?

  123.123.123.456 - ikev2 - AES256-SHA512

  I would like to expand this a little more, if her counterpart 123.123.123.456, must use IKEv2, you need to declare the IKEv2 in the tunnel group and add the relevant "Local and remote PSK"--> is for phase 1, and this means that it will use the IKEv2 defined policy before, and IPSec IKEv2 proposal is on phase 2, where the encryption card is you will need to replace the IKEv1 and use IPSec IKEv2 proposal. That way it will use for the phase 1 of the policy of IKEv2, that you set and defined transformation IKEv2, by making this change make sure that both sides are mirrored with IKEv2 and IPSec policy projects, as well as the tunnel will remain and will come with the new proposals.

  This custom affect no matter what another tunnel, as long as you change the settings to the correct tunnel group and do not delete all the proposals, simply remove the profile connection, those employees.

  3. you know what I mean? All groups of three tunnels on that off interface use different cryptographic cards, with only two of the three using ikev1 as a proposal of IPSec. Which will work?

  You can only have one card encryption applied by interface, and 3 tunnels using different sequence number with the same crypto map name, you cannot 2 tunnels on the same card encryption using IKEV1, and always in the same encryption card have the third tunnel using IKEv2 (different transformation defined using IKEv2). This custom cause no problem. 

  4. what Group Policy DfltGrpPolicy? Currently use all my groups of tunnel, but it is configured for ikev1. I'm not really sure what role is in everything it can so I simply add ikev2?

  Default group policy is added by default to all your groups of tunnel (connection profile), whenever create you one default group policy is inherited him by default, you can change to group policy that you can create, group policy is a set of attributes that will be used to define something or limit , for example, for a site, you can configure a VPN filter (filters the traffic that goes through the tunnel), now back to your topic, you define the protocols that will be negotiated as for an L2L IKEv1 or IKEv2, Anyconnect SSL or IKEv2, on default group policy, and so on, it is therefore important that you add the IKEv2 , so trading will be permitted, or both to create a new group policy and add the IKEv2 Protocol; and in the tunnel group, add the group policy relevant, that you just created.

  I hope that this is precisely, keep me posted!

  Please go to the note, and mark it as correct this post and the previous that it helped you!

  David Castro,

• How to limit the bandwidth in the VPN Tunnels in RV082?

  Hello

  It is possible to limit the bandwidth of the IPSEC VPN Tunnels or the traffic that goes through the tunnels?

  Use IP addresses or port numbers the same way and clients when limiting bandwidth to clients in the local network?

  Thank you very much

  Oliver

  There is a way to solve internal IP addresses, protocols or ports and specify the bandwidth

  I send you the links to access information on how to set it up.

  http://www6.nohold.NET/Cisco2/GetArticle.aspx?docid=3c09b393e3744ffd98330fd0031a4aa2_4228.XML&PID=80&converted=0

• I have created a VPN connection and it worked but you can't see how to remove Windows 7.

  Delete the VPN connection

  I have created a VPN connection and it worked but you can't see how to remove Windows 7.  I tried rt-click but no delete option.

  Open network and sharing Center. On the left side, click on change adapter settings. You will get all VPN connections that have been created and you can delete what you don't need.

• How to apply internet traffic in VPN tunnel users

  Hello

  Perhaps it is a simple matter to most of you, but it confuses me right now.

  Here's my situation:

  home - internet - ASA 5510 users - CORP LAN

  We have remote Ipsec VPN and anyconnect VPN, I think that the solution must work on two of them.

  My question is: "how to apply internet traffic user home to the VPN tunnel?

  We have "split tunnel" to only"'interesting traffic' VPN tunnel access LAN CORP.

  but now I need apply all traffic (internet + CORP LAN) user through VPN tunnel passes.

  so far, I did what I know:

  1. remove the "split tunnle" group policy

  2. the address in "remote user VPN address pool" are perhaps NAT/PAT travers ASA5510

  but I don't get why it doesn't work.

  all suggestions are appreciate!

  Thank you!

  A few things to configure:

  (1) Split tunnel policy to be passed under split in tunnelall tunnel

  (2) configure NAT on the external interface to PAT to the same global address.

  (3) configure "allowed same-security-traffic intra-interface" so that the tunnel VPN for Internet traffic can make a u-turn.

  Please share the current configuration if the foregoing still does not solve the problem. Thank you.

• How to create several site VPN on Cisco 2801

  Hello

  We use 2801 to our VPN needs. We have already configured a VPN site-to site inside. My current scenario is to create several VPN IE at different sites and a remote client VPN server for our road warriors (they use a cisco VPN client to connect).

  Let me know how can I achieve that scenario. Currently we have in VPN profiling in place. can I fill the script using VPN profiles, how it can be used. Kindly advice me at the earliest.

  Please find attached the 2801 direct configuration file, which is quite works very well

  Thanks in advance.

  Djamel.

  Djamel

  As much as I know it does no harm to have political isakmp 9 and isakmp 10 with the same parameters in each of them. But it also is not good. Others that extra isakmp policy I don't see anything that seems problematic in the config you have posted.

  HTH

  Rick

• How to configure the vpn using two segments in a tunnel?

  Hi guys,.

  Please help me how to set up two segment in a vpn tunnel. Our client has two segments which is 10.15 and 192.168. We have already established VPN connectivity. We can ping the 10.15 segment, but we can not ping 192.168. Attached is the sample configuration.

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key xxxxxx address 11.11.11.11

  !

  86400 seconds, duration of life crypto ipsec security association

  !

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  !

  map SDM_CMAP_1 1 ipsec-isakmp crypto

  Tunnel description

  defined peer 11.11.11.11

  Set security-association second life 28800

  game of transformation-ESP-3DES-SHA

  match address 102

  access-list 101 deny ip 192.168.202.0 0.0.0.255 host 10.15.0.177

  access-list 101 deny ip 192.168.202.0 0.0.0.255 host 192.168.30.174

  access-list 101 permit ip 192.168.202.0 0.0.0.255 any

  access-list 102 permit ip 192.168.202.0 0.0.0.255 host 10.15.0.178

  access-list 102 permit ip 192.168.202.0 0.0.0.255 host 192.168.30.174

  Here is the extended ping.

  Router #ping

  Protocol [ip]:

  Target IP address: 10.15.0.177

  Number of repetitions [5]:

  Size of datagram [100]:

  Timeout in seconds [2]:

  Extended commands [n]: y

  Source address or the interface: 192.168.202.3

  Type of service [0]:

  Set the DF bit in the IP header? [None]:

  Validate the response data? [None]:

  Data model [0xABCD]:

  In bulk, Strict, Record, Timestamp, Verbose [no]:

  Scan the range of sizes [n]:

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 10.15.0.177, wait time is 2 seconds:

  Packet sent with a source address of 192.168.202.3

  .!!!!

  Success rate is 80% (4/5), round-trip min/avg/max = 172/172/172 ms

  Router #ping

  Protocol [ip]:

  Target IP address: 192.168.30.174

  Number of repetitions [5]:

  Size of datagram [100]:

  Timeout in seconds [2]:

  Extended commands [n]: y

  Source address or the interface: 192.168.202.3

  Type of service [0]:

  Set the DF bit in the IP header? [None]:

  Validate the response data
  ? [None]:
  Data model [0xABCD]:
  In bulk, Strict, Record, Timestamp, Verbose [no]:
  Scan the range of sizes [n]:
  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 192.168.30.174, wait time is 2 seconds:
  Packet sent with a source address of 192.168.202.3
  .....
  Success rate is 0% (0/5)
  And here is the result of its crypto isakmp.
  Crypto ISAKMP router #show its

  status of DST CBC State conn-id slot

  11.11.11.11 22.22.22.22 QM_IDLE 1 0 ACTIVE

  And here is the encryption session.

  Router #show crypto sessio

  Session encryption router #show

  Current state of the session crypto

  Interface: FastEthernet0/0

  The session state: UP-ACTIVE

  Peer: 11.11.11.11 port 500

  FLOW IPSEC: allowed host 192.168.202.0/255.255.255.0 ip 192.168.30.174

  Active sAs: 2, origin: card crypto

  FLOW IPSEC: allowed host 192.168.202.0/255.255.255.0 ip 10.15.0.177

  Active sAs: 2, origin: card crypto

  And here are the details of the encryption session.

  Router #show crypto session detail

  Current state of the session crypto

  Code: C - IKE Configuration mode, D - Dead Peer Detection

  K - KeepAlive, N - NAT-traversal, X - IKE extended authentication

  Interface: FastEthernet0/0

  The session state: UP-ACTIVE

  Peer: 11.11.11.11 port fvrf 500: (none) ivrf: (none)

  Phase1_id: 11.11.11.11

  DESC: (none)

  IKE SA: local 22.22.22.22/500 remote 11.11.11.11/500 Active

  Capabilities: (None) connid:1 life time: 23:44:02

  FLOW IPSEC: allowed host 192.168.202.0/255.255.255.0 ip 192.168.30.174

  Active sAs: 2, origin: card crypto

  On arrival: dec #pkts'ed drop 0 0 life (KB/s) 4568454/27867

  Outbound: #pkts enc'ed 4 drop 1 life (KB/s) 4568453/27867

  FLOW IPSEC: allowed host 192.168.202.0/255.255.255.0 ip 10.15.0.177

  Active sAs: 2, origin: card crypto

  On arrival: #pkts dec' 8 drop 0 ed life (KB/s) 4591368/27842

  Outbound: #pkts enc'ed 8 drop 2 life (KB/s) 4591368/27842

   

  Hello

  Your side has 192.168.202.0/24 and you are trying to PING 10.15 successfully but not 192.168.30.174

  Check that the ASA has a route to 192.168.30.174 pointing to the external interface.

  Also check that the customer has defined the 192.168.30.174 as part of the VPN traffic correctly.

  Federico.

• How to get to the VPN tunnel to the subnet 2/3

  I have not yet tried something else a few years back I got on my back which head with an ASA firewall you cannot route traffic to a subnet of second or third (it's 2 or 3 jumps away) on a same VPN tunnel if you add routes to all LAN subnets in all required firewall and tunnels.

  I know other manufacturers such as SonicWall, here you can do it, so the question is, is possible in the firewall Cisco ASA with version 7.07 and 7.2.4? If this is not the case, is it possible in a future release? and if this is not possible, how can I make it work? I can't work with a firewall router 1 LAN to LAN s 3?

  Attached are also a network card for the visualization of all subnets.

  Thanks in advance

  Johan Mannerstrom

  ICT technician

  If the firewall HQ is already connected to LAN2 (way I mean), then you have even connect an interface on the firewall of HQ and in him giving an ip address that belongs to LAN2. As firewall HQ has a route to 192.168.20.0/24 and 18.0/24 and vice versa, that's enough.

  And you're on the point on the rest of the steps you have provided regarding the config.

  And of course, you must configure matching exemption to ACL and NAT image mirror on the remote VPN encryption too.