VPN tunnel with only one authorized service

Similar Questions

• Open Firefox, showing a tab, even with only one page

  I use Firefox on Mac. After a new update at the moment, Firefox takes up screen real estate at the top of its window to display a tab, even when there is no other page open (that is, there is only one tab). I only need to see the tabs if I have more than one open, but I can't find a framework to fight against this.

  Hello

  In Firefox 23, as part of an effort to simplify the firefox options define and protect users against unintentially damage their Firefox, the option to hide the tab bar has been removed.

  Refer to: http://limi.net/checkboxes-that-kill

  Fortunately, this can easily be solved if you want the tabs to keep hidden. You can install 'hide the bar tab with a tab' and extension hosted on the website of Mozilla Add - ons, which will restore the ability to hide the tab bar.

  Thank you and I hope this helps!

• RV042 VPN tunnel with Samsung Ubigate ibg2600 need help

  Hi all, ok before I completely remove all of my hair, I thought stop by here and ask the volume for you all with the hope that someone can track down the problem.

  In short I am configuring a 'Gateway to gateway' vpn tunnel between two sites, I don't have access to the config of the router from Samsung, but the ISPS making sure that they followed my setup - watching newspapers RV042, I don't however see the reason for the failure - im no expert vpn...

  Sorry if the log file turns on a bit, I didn't know where the beginning and the end was stupid I know... any advice would be greatly welcomed lol.

  System log
  Current time: Fri Sep 2 03:37:52 2009 all THE Log Log Log Log VPN Firewall Access system
   
  Time
  Type of event Message
  2 sep 03:36:01 2009 value of VPN Log [Tunnel negotiation Info] Inbound SPI = c3bdba08
  2 sep 03:36:01 2009 value of outbound SPI VPN Log [Tunnel negotiation Info] = c664c1ca
  2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] > initiator send fast Mode 3rd package
  2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] Quick Mode Phase 2 SA established, IPSec Tunnel connected
  2 sep 03:36:02 2009 VPN journal Dead Peer Detection start, DPD delay = timeout = 10 sec 10 sec timer
  2 sep 03:36:02 2009 VPN received log delete SA payload: ISAKMP State #627 removal
  2 sep 03:36:02 2009 VPN Log Main Mode initiator
  2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] > Send main initiator Mode 1 package
  2 sep 03:36:02 2009 charge of VPN journal received Vendor ID Type = [Dead Peer Detection]
  2 sep 03:36:02 2009 VPN Log [Tunnel negotiation of Info]< initiator="" received="" main="" mode="" 2nd="" packet="">
  2 sep 03:36:02 2009 VPN Log [Tunnel negotiation Info] > initiator send Mode main 3rd package
  2 sep 03:36:03 2009 VPN Log [Tunnel negotiation of Info]< initiator="" received="" main="" mode="" 4th="" packet="">
  2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN > main initiator Mode to send 5 packs
  2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN > initiator receive hand Mode 6 Pack
  2 sep 03:36:03 2009 log VPN main mode peer ID is ID_IPV4_ADDR: '87.85.xxx.xxx '.
  2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN Mode main Phase 1 SA established
  2 sep 03:36:03 2009 log VPN [Tunnel negotiation Info] initiator Cookies = c527 d584 595 c 2c3b
  2 sep 03:36:03 2009 log VPN [Tunnel negotiation Info] responder Cookies = b62c ca31 1a5f 673f
  2 sep 03:36:03 2009 log quick launch Mode PSK VPN + TUNNEL + PFS
  2 sep 03:36:03 2009 Log [Tunnel negotiation Info] VPN > initiator send fast Mode 1 package
  2 sep 03:36:04 2009 VPN Log [Tunnel negotiation of Info]< initiator="" received="" quick="" mode="" 2nd="" packet="">
  2 sep 03:36:04 2009 value of VPN Log [Tunnel negotiation Info] Inbound SPI = c3bdba09
  2 sep 03:36:04 2009 value of outbound SPI VPN Log [Tunnel negotiation Info] = e3da1469
  2 sep 03:36:04 2009 VPN Log [Tunnel negotiation Info] > initiator send fast Mode 3rd package
  2 sep 03:36:04 2009 VPN Log [Tunnel negotiation Info] Quick Mode Phase 2 SA established, IPSec Tunnel connected
  2 sep 03:36:04 2009 VPN journal Dead Peer Detection start, DPD delay = timeout = 10 sec 10 sec timer
  2 sep 03:36:05 2009 VPN received log delete SA payload: ISAKMP State #629 removal

  PFS - off on tada and linksys router does not support the samsung lol! connected!

• ASA base S2S VPN, Tunnel establishes only when interesting traffic hits to end distance

  Dear all,

  I need your help to solve the problem mentioned below.

  VPN tunnel established between the unit two ASA.   A DEVICE and device B

  (1) if interesting traffic initiates a LAN device. traffic ACL hits. TUNEL is not coming

  (2) if interesting traffic initiates B LAN device. Tunnel will establish all the works of serivces

  (3) after the Tunnel device establishmnet B. We forced to tunnel down at both ends. Interesting again traffic initiates device a surpringly tunnel

  will go up.   After 2 or 3 days (after life expire 86400 seconds) initiated traffic of device A, tunnel will not esatblish.

  (it comes to rescue link: interesting won't be there all the time.)

  checked all parametrs, everthing seems fine. Here are the logs of attached but not more informative debugging on the balls. Please suggest.

  February 2, 2010 13:23:17: % ASA-7-713236: IP = 81.145.x.x, IKE_DECODE new SEND Message (msgid = 0) with payloads: HDR + HER (1), SELLER (13) + (0) NONE total length: 496

  February 2, 2010 13:23:18: % ASA-6-713219: IP = 81.x.x.x, KEY-ACQUIRE Queuing messages are treated when SA P1 is finished.

  February 2, 2010 13:23:18: % ASA-6-713219: IP = 81.x.x.x, KEY-ACQUIRE Queuing messages are treated when SA P1 is finished.

  February 2, 2010 13:23:23: % ASA-6-713219: IP = 81.x.x.x, KEY-ACQUIRE Queuing messages are treated when SA P1 is finished.

  February 2, 2010 13:23:25: % ASA-7-715065: IP = 81.x.x.x, history of mistake IKE MM Initiator WSF (struct & 0x1abb1e10) , : MM_DONE, EV_ERROR--> MM_WAIT_MSG2, EV_RETRY--> MM_WAIT_MSG2, EV_TIMEOUT--> MM_WAIT_MSG2 NullEvent--> MM_SND_MSG1, EV_SND_MSG--> MM_SND_MSG1, EV_START_TMR--> MM_SND_MSG1, EV_RESEND_MSG--> MM_WAIT_MSG2, EV_RETRY

  February 2, 2010 13:23:25: % ASA-7-713906: IP = 81.x.x.x, IKE SA MM:56f95c85 ending: flags 0 x 01000022, refcnt 0, tuncnt 0

  February 2, 2010 13:23:25: % ASA-7-713906: IP = 81.x.x.x, sending clear/delete with the message of reason

  February 2, 2010 13:23:25: % ASA-3-713902: IP = 81.x.x.x, counterpart of drop table counterpart, didn't match!

  February 2, 2010 13:23:25: % ASA-4-713903: IP = 81.x.x.x, error: cannot delete PeerTblEntry

  Hi, I have a similar problem a long time ago. You can choose which set up the tunnel in your crypto card:

  card crypto bidirectional IPsec_map 1 set-type of connection

  I hope that it might help to solve your problem. Kind regards.

• VPN tunnel with U-turn

  Hello

  I am trying to understand the functioning of DNS with u-turn. I'm looking for in the configuration of VPN tunnel between ASA 5510 (main office) and PIX 506 (remote).

  Currently all the jobs in the remote offices are connected through VPN tunnel between PIX506 and VPN 3000 to a hub, so that they use the internal DNS server at the main office. I need to use u-Turn on ASA to allow remote surfing the net users. With u-Turn config, remote workstation still will use DNS server in the main office to resolve the IP addresses?

  Thank you

  LF

  Hey Forman.

  SplitDNS and Splittunneling are both used with remote access clients. In your case, that you try to configure a site to site VPN tunnel, so to 'divide' traffic you will use the crypto acl to set valuable traffic to the VPN. However, this ACL uses IP addresses in order to determine whether the traffic must be encrypted or not, this is why your DNS lookup would have to occur before the traffic is encrypted. Then, you can set the DNS server for the remote network to be the DNS through the VPN tunnel and ensure that the DNS server's IP address is part of the interesting traffic or you must ensure that the local DNS server is able to resolve names.

  In the previous case where you use u-turn, all gets automatically tunnele so you don't have to worry about your DNS queries in the tunnel.

  I hope that this explains the behavior.

  Kind regards

  ATRI.

• MAF: Not able to run the sample project or a simple project with only one page

  Hi all

  I am trying to run examples of applications of the MAF delivered with Jdeveloper 12.1.3. I am not able to run these applications on the device in the emulator. They gets deployed successfully. However, when I try to open these applications, it hangs on the initial screen of the Oracle.

  I even tried to create a new MAF application with only a device with a page of the AMX. Tried to deploy, but still get the same result.

  No idea what could be the problem?

  Thank you

  Ajay

  Hello

  Problem has been resolved, after the re-installation of the Jdev and MAF extension.

  Understood that somehome, maf - application.xml couldn't refer to the features of the maf - feature.xml. When I created a new feature in the MAF - feature.xml, it was the adfmf - feature.xml and maf-application creation could refer to the functionality of this file.

  This seems to me an installation problem. I have therefore re-installed, now its works very well.

  Thank you

  AJ

• Set up after effects CS 6 for rendering in a network with only one license.

  I searched on and off a few days to find specific installation instructions for submitting projects for the network rendering but all I can find refers to installation somehow AE on several machines in non-licence mode and, essentially, to present a 'batch' type work to be distributed, sync'd and collected. OK, I get this. But I can't find anything on the details of the installation on several machines.

  So if I understand things at this point, the question is really how to install several copies of the AE6 to systems with only a single license? I have a license key single with a 6 Suite Premium CS and wait that I would not be able to cross activation after installation or have afraid to try for fear that Adobe thinks I'm trying to dodge the licenses.

  Thanks in advance for any help.

  > afraid to try for fear that Adobe thinks I'm trying to dodge the licenses

  Do not be afraid. Do it. There is no risk in trying to install the software on as many machines as you want. Even in cases where you have only a license to use our software on two machines, the worst thing that happens is said you to disable on a computer before turning on another.

  See these messages:

  installation of renderers after effects CC with Adobe Creative Cloud

  codecs and the After Effects CS6 and after effects CC rendering engine

• Between Cisco ASA VPN tunnels with VLAN + hairpin.

  I have two Cisco ASA (5520 and 5505) both with version 9.1 (7) with Over VPN and Security Plus licenses. I try to understand all the internet a traffic tunnel strategy VLAN especially on the 5520 above the 5505 for further routing to the internet (such as a hair/u-turn hairpin). A few warnings:

  1. The 5505 has a dynamically assigned internet address.
  2. The 5505 has sometimes no device turned on behind her, bringing interfaces down to the inside (which can cause problems from site to site).
  3. The 5520 cannot be a client of ezvpn due to its current role as a server of webvpn (anyconnect).

  Let me know if I need to post my current config. Basically, I'm starting from scratch after several attempts.

  Thank you!

  1. The 5505 has a dynamically assigned internet address.

  You can use the following doc to set up the VPN and then this document to configure Hairping/U tuning

  2. the 5505 has sometimes no device turned on behind her, bringing interfaces down to the inside (which can cause problems from site to site).

  Make sure that the interface is connected to a switch so that it remains all the TIME.

  3. 5520 the may not be a ezvpn customer due to she has current as one role anyconnect webvpn ()) server.

  You can use dynamic VPN with normal static rather EZVPN tunnel.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• import address book - names do not - even with only one name only

  I've simplified the import csv for first name and last name only. The import in TB shows map everything is OK, but when the address book is seen there are no names listed. A name can be searched but not shown. Totally puzzled.

  I want Outlook to tuberculosis, but it is a real blocker.

  I tried the process on two PCs one running XP the other 7 with the same result.

  Tell me, when you open the address book is there a list of imported address or anything like that at all.

  Note there is first a final and full name. This is the display name that appears in the lists. In the absence of the display name of the part of the address of e-mail before the @ is displayed.

  I speak a little CSV and clean up the content here http://thunderbirdtweaks.blogspot.com.au/2013/03/importing-csv-files.html

• NAT on 8.3 and VPN tunnel with overlapping addresses

  Hi all

  I was looking at this document from Cisco and I think I understand how to convert the nat policy than the version 8.3 and later, but I was wondering what is happening to the acl crypto, you are always using the same as the older versions? As you know the 8.3 then NAT requires to use the original instead of the address translated to the ACL, but I don't know if this applies to crypto ACL as well. Pointers?

  Example from the link:

   access-list new extended permit ip 192.168.2.0 255.255.255.0 192.168.3.0 255.255.255.0 !--- This access list (new) is used with the crypto map (outside_map) !--- in order to determine which traffic should be encrypted !--- and sent across the tunnel. access-list policy-nat extended permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0 !--- The policy-nat ACL is used with the static !--- command in order to match the VPN traffic for translation. 

   static (inside,outside) 192.168.2.0 access-list policy-nat !--- It is a Policy NAT statement. !--- The static command with the access list (policy-nat), !--- which matches the VPN traffic and translates the source (192.168.1.0) to !--- 192.168.2.0 for outbound VPN traffic.

   crypto map outside_map 20 match address new !--- Define which traffic should be sent to the IPsec peer with the !--- access list (new).

  Thank you

  V

  Hi rc001g0241,

  I posted your question for clarity sake along.

  "what happens to the crypto acl, always use you even as older versions?"

  As you can see, Cisco doc you posted shows that you need to target for crypto engine is what happens after the nat policy has succeeded, illustrated here: "address match map crypto outside_map 20 new".

  "As you know the 8.3 then NAT requires to use the original instead of the address translated to the ACL, but I don't know if this applies to crypto ACL as well. Pointers?

  There is no such requirement and ACL target you in the engine crytop for the tunnel bound traffic can be a natted post address, that's what shows Cisco Doc and it is correct.

  Hope that answers your questions.

  Thank you

  Rizwan James

• VPN tunnel with IP dynamic

  Question:

  Is it possible to install a GRE tunnel between two routers, one that has a dynamic IP, the other has a static IP address. If this isn't the case, GRE, is there another tunneling protocol we could use?

  In the search for setting up a VPN, I found that the way suggested to do is a GRE tunnel, so that dynamic routing work via VPN. We do not use dynamic routing, but I want the flexible design for future changes that will occur.

  Our facility is:

  2651XM (hub) to the corporate office (static IP). DS-1

  827H (spokes) to each branch (dynamic IP via DHCP). ADSL.

  IOS version 12.2 (13) T supports Multipoint GRE function which will allow your GRE tunnel on the side of ADSL to use a dynamic IP address. Locate the CCO love and documentation DMVPN (dynamic multipoint VPN).

• Creating a device with only one key Windows 8 start?

  I recently bought a new HARD drive for my laptop and my original hard drive went too well to get an ISO out of it. My other computers are Windows 7, and I do not have a backup. I found this:

  http://Windows.Microsoft.com/en-us/Windows-8/upgrade-product-key-only

  but it's only for the upgrade of the computer you are using. I thought I saw a boot for 8.1 media where you just need the key, but I can't find anything for Windows 8. Help, please! I don't want to buy a new copy, when I have my key :(

  Hello

  The site offers 8 and 8.1... I don't think that you have to install...

  Run through the process, you will be able to create one or Flash Drive, DVD, record an ISO (better idea)... It can be converted into anything...

  http://Windows.Microsoft.com/en-us/Windows-8/upgrade-product-key-only

  I don't think that it will work with OEM pre-installed Windows...

  Is there another link to download Win 8.1 which requires no key until it is installed.

  http://Windows.Microsoft.com/en-us/Windows-8/create-reset-refresh-media

  Depending on your installation, you may need a temporary license key to win 8.1, then after installation you can enable it with the key Win 8...

  XKY4K-2NRWR-8F6P2-448RF-CRYQH (Windows 8 Professional)
  RR3BN-3YY9P-9D7FC-7J4YF-QGJXW (Windows 8 Professional with Media Center)
  FB4WR-32NVD-4RW79-XQFWH-CYQG3 (Windows 8 [home])
  XHQ8N-C3MCJ-RQXB6-WCHYG-C9WKB (Windows 8.1 Professional)
  GBFNG-2X3TC-8R27F-RMKYB-JK7QT (Windows 8.1 Professional with Media Center)
  334NH-RXG76-64THK-C7CKG-D3VPT (Windows 8.1 [home])

• But two VPN tunnels start only

  I have an ASA5505 I need to connect to two remote networks. I have worked if the first tunnel to my work of HQ. I must now add a remote office. My HQ and remote offices using two SonicWALL PRO2040 devices, same firmware and OS.

  I used the config of tunnel work to create a second. The first tunnel starts and works perfectly. When I try to send traffic to the remote office second tunnel even never started.

  I have look in newspapers at both ends (I have access to the remote location via client software) and there is no exchange between my ASA and the PRO2040.

  What more could I do to get the ASA to start the tunnel?

  I am running 8.0 on my ASA. Are all enhanced 4.0.0.2 SW.

  Hello

  OK, so connections to networks remote need to have a converter nat 0 applied to them. In your config your nat 0 looks like this:

  NAT (inside) 0-list of access outside_cryptomap

  in order to get your new VPN to work, you will need to apply it to the new traffic, however, you will need to create a new acl to the NAT 0 statement. The commands that you need to fill it are:

  access-list extended sheep allowed inside-network ip, 255.255.255.0 mon-hq 255.255.248.0

  access-list extended sheep allow office2 inside-network 255.255.255.0 ip 255.255.255.0

  no nat (inside) 0-list of access outside_cryptomap

  NAT (inside) 0 access-list sheep

  clear xlate

  Other locomotives ok, so who should do :)

• You can print with only one cartridge

  You have to have two cartridges print?

  Hello

  No, all the cartridges (with inks) you must be able to print on almost any printer.

  Kind regards.

• 2 separated on same ASA VPN tunnels can communicate with each other

  Here's the scenario that I have a VPN tunnel with one of my remote locations.   I also have a VPN Tunnel with a provider that supports the equipment for my organization.   I need to have my supplier able to communicate with equipment that live in my other VPN tunnel.   The two Tunnels are on the same ASA5540.

  1 is it Possible?

  2 How set it up?

  Thank you

  Follow this link for example. Enhanced spoke-to-spoke VPN, allows the two tunnels ending to your asa5540 to connect, using parameter permit intra-interface with configuration accless-list permits traffic of each endpoint of the tunnel.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00804675ac.shtml