How to apply internet traffic in VPN tunnel users

Similar Questions

• Internet via the VPN tunnel

  Hi I have a question.

  I hope one of you can help me.

  My problem is that I want to the internet using VPN tunnenl.

  I have a VPN connection with my ASA 5505 at home.

  I am able to access the entire inside of the devices. But I'm unable to access the internet.

  is it possible the internet using the internet connection I have at home.

  i'f played a bit with the following commands:

  same-security-traffic permits intera-interface &

   same-security-traffic permit intera-interface & split-tunnel-policy tunnelall

  ASA version: 9.1 2

  ASDM version: 7.1 (3)

  Greetings

  Palermo

  the client that is connected via VPN you are able to ping 4.2.2.2?

  If Yes, if you issue a nslookup google.com is the resolved name?

  If this isn't the case, then I think that the following command highlighted is the problem:

  Group Policy home-attributes VPNSSL
  WINS server no
  DNS server no
  Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client

  Try setting your DNS here server and test.

  --

  Please do not forget to select a correct answer and rate useful posts

• How to get specific IP through VPN tunnel

  I've implemented remote access via VPN Cisco VPN.
  We use the tunneling split at the tunel internal IP of VPN tunnel only range.
  Now I need to get a specific IP address on the Cisco VPN Client
  through Internet and internal network.
  I added this specific IP address to split tunnel ACL
  I can check it out using Cisco VPN Client, status > statistics, details of the itinerary.
  but when I traceroute to that specific IP address it ends on
  first jump, ASA public interface.
  ASA road 0.0.0.0/0.
  I need to put in place?

  Hello

  If you need to allow the VPN client to connect to the ASA and you--turn to the Internet, you must:

  permit same-security-traffic intra-interface

  Also, make sure you NAT traffic:

  NAT (outside) 1 VPN-range

  Global 1 interface (outside)

  Be careful with the above NAT commands (is just one example and depends on your configuration).

  Federico.

• routing of traffic between vpn tunnels

  Hello

  I have a scenario like that.

  There are two branch office vpn tunnels to the headquarters. I want to load balance the traffic on this two links using EIGRP.

  in this way, another branch offic is also connected to the head office. now, I want to ensure the communication between two branch of the office through seat over these vpn tunnels.

  Concerning

  skrao

  Hello

  Here is a great link that describes a similar setup to yours:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a008009438e.shtml

  Good reading and after return if there is anything that you are not clear.

  PLS, don't forget to rate messages.

  Paresh

• How to block all traffic except vpn traffic and traffic bureau HQ

  Hello

  Someone please advise me how to block all traffic except inbound traffic through the VPN and traffic from the IP of the HQ Office.

  My router is 881/K9 Cisco router. Currently, I have blocked all IP addresses with the exception of the IP Office HQ using access-list on the brance office website.

  I put the IP list allowed according to IP location of the VPN user. But now the VPN user become more and more and thus be difficult to block the IPs based on their current location. Sometimes not possible to know their WAN ip address.

  Thanks in advance.

  Have you considered allowing the IPSEC IP Protocol, TCP port, intellectual property all UDP ports and then by blocking all other traffic?

• AnyConnect: How to route ALL traffic over VPN

  In the past, when I use a built-in Windows VPN (PPTP), I could choose everything would go through the VPN, or if only the things that did not resolve been there. I copy/paste the VPN connection and rename them so we called something_all and the other something_std. I choose which one I needed and start this one.

  Now I use Secure Mobility Cisco AnyConnect Client (on my Windows 7 machine), I don't seem to have this option. I seem to be locked in a mode where only the URLS that fail to solve find themselves through the VPN. It works for the private areas, my employer. This means having access to machines which are not turned to the audience.

  My problem is that, sometimes, I want everything to go through it. For example, if I'm in Europe and that someone (in America) tells me that I need to visit a site and solve a problem, what I find is that despite type in American URL, I get redirected to the European site, because it is a public site. I want to switch the VPN in the mode 'road everything', or even better, to have a list that I manage areas I want to go through it (even if the all or nothing is all that I really need).

  Is this possible? I saw the option called something like 'allow access to the local network', but this doesn't seem to be something useful.

  The ultimate test is that if I go to one of these sites, what - is - my - ip - address, it does not say I'm in Europe, but on the contrary says: I'm in America (or as much as the goal of the VPN is, I have several choices of my employer).

  If instead of "tunnelspecified", we use the keyword "tunnelall" the value with 'split-tunnel-policy', which will push the route 0.0.0.0/0 for the session of your client.

  It is indeed the wildcard character that you are asking about.

• RV180 VPN route all internet traffic via IPSec VPN

  Hello

  I install my RV180 to VPN to our headquarters Fortigate 60 C. It works really well

  My only problem is that I don't know how to move internet traffic on our remote site by Headquarters. We want to use this technique so that all sites have the same web content filtering provided by our main Fortigate unit. I see clearly that all traffic destined to our internal network will go trough the VPN tunnel, but internet traffic will go through our modem at the remote site.

  My way of fortigate thinking said that I need a static route to transfer all traffic through the VPN tunnel. I've read elsewhere that I need to set up some sort of ACL.

  Anyone else has any ideas on this / has anyone successfully implemented somehting similar?

  Hi Jared,

  I don't think that RV180 takes complete care of tunneling. Complete tunneling allows you to all your traffic to VPN. RV180 made only split tunneling.

  Thank you

  Vijay

  Sent by Cisco Support technique iPad App

• Send all traffic through the vpn tunnel

  Does anyone know how to send all traffic through the tunnel vpn on both sides?  I have a server EZVpn on one side and one EZVpn client on the other.  I'm not natting on each side.  I use the value default 'tunnelall' for the attributes of group policy.  On the client side all traffic, even if not intended for the subnet of the side server, seems to pass through the tunnel.  But if I ping the side server, the same rules don't seem to apply.  Traffic destined for rates aside customer through the tunnel, but the traffic that is not pumped on the external interface in the clear.  That's not cool.

  Hello

  Clinet traffic to server through tunnel, that's right, right?

  Traffic from server to client through tunnel, but the rest of the traffic is not, no?

  This works as expected because in ezvpn, politics of "tunnel all ' is for traffic is coming from the client., do not leave the server.

  Side server, customer traffic will pass through tunnel, the rest used.

  Sian

• Help with a VPN tunnel between ASA 5510 and Juniper SSG20

  Hello

  We have a customer wanting to configure a VPN Site to Site tunnel between a new purchased 5510 of ASA located in his direction with its Juniper SSG20 Office, located in the main office. We contacted HP and they send us a Cisco professional to do the job.

  After 2 days from 16:00 to 22:00 and error and countless hours of research online and nunerous calls, we are still unable to get traffic from the network of agencies to enter the tunnel.

  Main branch
  1.1.1.2                                 1.1.1.1
  -----                                               -----------
  192.168.8.0/24 | ASA|-----------------------------------| Juniper |    192.168.1.0/24
  -----                                               -----------
  192.168.8.254 192.168.1.254

  According to Cisco professionals, the tunnel is now in place but no traffic through. We are unable to ping anything on the network on the other side (192.168.1.0/24). We receive timeout ping all the time. The Cisco professional told us it's a routing or NAT problem and he's working on a solution!

  Through research, I came across a post on Experts-Exchange (here) [the 1st comment on the original post] which States "...". that both sides of the VPN must have a different class of LAN for the VPN to work... " Would that be our problem?

  It has become a critical issue to the point that he had to replace the Cisco ASA with a temporary Juniper SSG5 on another subnet (192.168.7.0/24) to get the tunnel upward and through traffic until the ASA VPN issue is resolved and I didn't need to say that the client is killing us!

  Help is very appreciated.

  Thank you

  1. Yes, ping package from the interface of the ASA is considered valuable traffic to the LAN of Juniper.

  SAA, need you traffic from the interface source ASA's private, because interesting to determine by crypto ACL MYLIST traffic between 192.168.8.0/24 and 192.168.1.0/24.

  You will also need to add the following configuration to be able to get the ping of the interface of the ASA:

  management-private access

  To initiate the ping of the private interface ASA:

  ping 192.168.1.254 private

  2. the default time before the next generation of new key is normally 28800 seconds, and if there is no interesting traffic flowing between 2 subnets, he'll tear the VPN tunnel down. As soon as there is interesting traffic, the VPN tunnel will be built automatically into the next generation of new key. However, if there is traffic before generating a new key, the new tunnel will be established, and VPN tunnel will remain standing and continue encrypt and decrypt traffic.

  Currently, your configuration has been defined with ITS lifetime of 3600 seconds GOLD / 4608000 kilobytes of traffic before the next generate a new key (it will be either 3600 seconds, or 4608000 kilobytes period expires first). You can certainly change it by default to 28800 seconds without configuring kilobytes. SA life is negotiated between the ASA and Juniper, and whatever is the lowest value will be used.

  Hope that helps.

• NAT VPN tunnel and still access Internet traffic

  Hello

  Thank you in advance for any help you can provide.

  I have a server with the IP 192.168.1.9 that needs to access a subnet remote from 192.168.50.0/24, through the Internet.  However, before the server can access the remote subnet, the server IP must be NAT'ed to 10.1.0.1 because the VPN gateway remote (which is not under my control) allows access to other customers who have the same subnet address that we do on our local network.

  We have a 2801 Cisco (running c2801-advsecurityk9 - mz.124 - 15.T9.bin) set up to make the NAT.  It is the only gateway on our network.

  I have configured the Cisco 2801 with the following statements of NAT and the relevant access lists:

  access-list 106 allow host ip 192.168.1.9 192.168.50.0 0.0.0.255

  NAT extended IP access list
  refuse the host ip 192.168.1.9 192.168.50.0 0.0.0.255
  deny ip 192.168.1.0 0.0.0.255 192.168.3.0 0.0.0.255
  ip permit 192.168.1.0 0.0.0.255 any

  route allowed ISP 10 map
  corresponds to the IP NAT

  IP nat EMDVPN 10.1.0.1 pool 10.1.0.1 netmask 255.255.255.0
  IP nat inside source list 106 pool EMDVPN
  IP nat inside source map route ISP interface FastEthernet0/1 overload

  When the server (192.168.1.9) attempts to ping on the subnet of 192.168.50.0/24 devices, the VPN tunnel is established successfully.  However, after that, the server is no longer able to access the Internet because the NAT translation for 192.168.1.9 has changed since the external IP address of the router (FastEthernet0/1) at 10.1.0.1.

  The documentation I've seen on the site of Cisco says that this type of Setup allows only host subnet communication.  Internet access is not possible.  However, maybe I missed something, or one of you experts can help me.  Is it possible to configure the NAT router traffic destined to the VPN tunnel and still access the Internet by using the dynamic NAT on FastEthernet0/1?

  Once again, thank you for any help you can give.

  Alex

  Hello

  Rather than use a pool for NAT

  192.168.1.9 - 10.1.0.1 > 192.168.50.x

  ACL 102 permit ip 192.168.1.9 host 192.168.50.0 0.0.0.255

  RM-STATIC-NAT route map permit 10
  corresponds to the IP 102

  IP nat inside source static 192.168.1.9 10.1.0.1 card expandable RM-STATIC-NAT route

  ACL 101 deny host ip 192.168.1.9 192.168.50.0 0.0.0.255
  ACL 101 by ip 192.168.1.0 0.0.0.255 any
  overload of IP nat inside source list 101 interface FastEthernet0/1

  VPN access list will use the source as 10.1.0.1... *.

  Let me know if it works.

  Concerning

  M

• Internet through a RA IPSec VPN Tunnel traffic

  Armed with an ASA 5505 Security Plus, I configure IPSec VPN for RA the VPN IP address pool is in the 192.168.2.0/28 network.

  The Lan is 192.168.1.0/24 with inside interface a.254.

  The VPN works great. What I would do is to route all internet through the firewall traffic when users are connected to the VPN. I put this gateway 192.168.1.254 tunnel, but I'm having no luck to get it works.

  Any ideas?

  Thanks in advance!

  You are just going to route internet traffic to the remote vpn client to the ASA and backward on the Internet?

  If the above statement is correct, you need not configure the tunnel default gateway.

  But you need to configure NAT for the ip pool, so they can go to the internet, as well as the 'same-security-movement' command as follows:

  NAT (outside) 1 192.168.2.0 255.255.255.0

  permit same-security-traffic intra-interface

  In addition, assuming that you have not have split configured tunnel.

• VPN, Internet and a Split Tunnels traffic

  Please attached photo because I hope that explains what I really want to do, but here's the break down.

  When a VPN Client connects to remote access to 1-ASA5510 I want all Internet traffic to send to 2 - ASA5510 instead of back to the default route. When it comes out 2-ASA5510, it passes through the content filter. 2 - ASA5510 has Split Tunnel put in place and we are trying to do away with Tunnel from SPlit.

  I hope this is clear enough.

  Any ideas would be helpful

  Dan

  Dan,

  Difficult but doable! First of all, there is a nice feature in the ASA that allows configuration of remote proxy based on VPN profile by: -.

  Group Policy <> attributes

  use a MSIE-proxy-server method

  Internet Explorer-proxy server value x.x.x.x

  activate Internet Explorer-proxy local-bypass

  Well Yes you guessed it - works only on Microsoft Internet Explorer.

  I don't think that any policy based routing would work for you - bad luck.

  But you can try another feature - traffic through the tunnel, which is normally used in the topllogy of EasyVPN: -.

  http://www.Cisco.com/en/us/prod/collateral/iosswrel/ps6537/ps6586/ps6635/ps6659/prod_white_paper0900aecd8060b477.html

  Configuration of the ASA at the bottom, I probably would test this with the IP address of the 2651 router!

  HTH.

• Site to site VPN, I need all internet traffic to exit the site.

  I have 2 sites connected via a pair of SRX5308

  A = 192.168.1.0/24

  IP WAN = 1.1.1.1

  B = 192.168.2.0/24

  IP WAN = 2.2.2.2

  Now what I need to do, is to have all traffic from B to go to the site one even traffic destined to the internet. That is, I need internet traffic out of our network with the IP 1.1.1.1, even if it is from the network B.

  On my I have set up a route 1.1.1.1 of the ISP, then a value by default 0/0 to 192.168.1.1 it ASA knows how to get to the peer VPN is a more specific route, but sends everything above the tunnel, at the remote end which then hairpin of ASA routes internet outside its own WAN port traffic.

  I can understand though not how to so the same thing on the pair of SRX5308 they either don't raise the tunnel or internet route to the local site address B.

  Anyone have any ideas?

  I need to do this because we are logging and monitoring of internet traffic to A site via tapping from upstream to various IDS solutions and will not (cannot) reproduce this to all our remote sites.

  Thank you

  Dave.

  After some more thought and testing I came up with a workable solution to my own problem. I'll share it here in case it can help others.

  (1) use the wizard at both ends to implement a normal VPN that connects the two segments of network 192.168.1.0 and 192.168.2.0

  (2) go to site VPN - VPN policy remote router192.168.2.1 and click Edit

  (a) disable Netbios

  (b) select "None" from the drop-down list the remote IP address.

  (c) to apply the change

  3) go to the VPN-> VPN policy on the head end site (192.168.1.1) and click Edit

  (a) disable Netbios

  (b) select "None" from the drop-down list the local IP address

  (c) to apply the change

  Now all the traffic wil go down the VPN tunnel and exit to the internet on the site of head end. Hope this helps others with the same question.

• Windows - Internet access, no split Tunnel L2TP VPN Clients does not

  Greetings!

  I have four ASA 5505 that I configured with 4 site to site VPN tunnels (works perfectly) to connect to our company facilities 4. The ASA is also configured with remote access L2TP/IPsec so that a specific group of users of portable computers can connect to and access to all facilities. It also works very well except for one important exception - my split tunnel setting doesn't seem to work, because I can't connect to the Internet outside the VPN resources.

  I accept the inherent risk of allowing tunnels to split from a security point of view since I take the necessary steps to secure the systems used for remote access. I would appreciate any feedback on how to get the job of split tunnel.

  Here is the configuration:

  : Saved
  :
  ASA Version 1.0000 11
  !
  SGC hostname
  domain somewhere.com
  names of
  COMMENTS COMMENTS LAN 192.168.2.0 name description
  name 75.185.129.13 description of SGC - external INTERNAL ASA
  name 172.22.0.0 description of SITE1-LAN Ohio management network
  description of SITE2-LAN name 172.23.0.0 Lake Club Network
  name 172.24.0.0 description of training3-LAN network Southwood
  description of training3 - ASA 123.234.8.124 ASA Southwoods name
  INTERNAL name 192.168.10.0 network Local INTERNAL description
  description of name 192.168.11.0 INTERNAL - VPN VPN INTERNAL Clients
  description of Apollo name 192.168.10.4 INTERNAL domain controller
  description of DHD name 192.168.10.2 Access Point #1
  description of GDO name 192.168.10.3 Access Point #2
  description of Odyssey name 192.168.10.5 INTERNAL Test Server
  CMS internal description INTERNAL ASA name 192.168.10.1
  name 123.234.8.60 description of SITE1 - ASA ASA management Ohio
  description of SITE2 - ASA 123.234.8.189 Lake Club ASA name
  description of training3-VOICE name Southwood Voice Network 10.1.0.0
  name 172.25.0.0 description of training3-WIFI wireless Southwood
  !
  interface Vlan1
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Vlan2
  nameif INSIDE
  security-level 100
  255.255.255.0 SGC-internal IP address
  !
  interface Vlan3
  nameif COMMENTS
  security-level 50
  IP 192.168.2.1 255.255.255.0
  !
  interface Ethernet0/0
  Time Warner Cable description
  !
  interface Ethernet0/1
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/2
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/3
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/4
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/5
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/6
  Description for Wireless AP Trunk Port
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/7
  Description for Wireless AP Trunk Port
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  boot system Disk0: / asa821-11 - k8.bin
  Disk0: / config.txt boot configuration
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS domain-lookup outside
  INTERNAL DNS domain-lookup
  DNS domain-lookup GUEST
  DNS server-group DefaultDNS
  Name-Server 4.2.2.2
  domain somewhere.com
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  DM_INLINE_TCP_1 tcp service object-group
  EQ port 3389 object
  port-object eq www
  EQ object of the https port
  EQ smtp port object
  the DM_INLINE_NETWORK_1 object-group network
  network-object SITE1-LAN 255.255.0.0
  network-object SITE2-LAN 255.255.0.0
  network-object training3-LAN 255.255.0.0
  object-group training3-GLOBAL network
  Southwood description Global Network
  network-object training3-LAN 255.255.0.0
  network-object training3-VOICE 255.255.0.0
  network-object training3-WIFI 255.255.0.0
  DM_INLINE_TCP_2 tcp service object-group
  EQ port 5900 object
  EQ object Port 5901
  object-group network INTERNAL GLOBAL
  Description Global INTERNAL Network
  network-object INTERNAL 255.255.255.0
  network-object INTERNALLY-VPN 255.255.255.0
  access-list outside_access note Pings allow
  outside_access list extended access permit icmp any CMS-external host
  access-list outside_access note that VNC for Camille
  outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_2
  access-list outside_access note INTERNAL Services
  outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_1
  DefaultRAGroup_splitTunnelAcl list standard access allowed INTERNAL 255.255.255.0
  access-list sheep extended ip INTERNAL 255.255.255.0 allow INTERNAL VPN 255.255.255.0
  access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
  access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
  access-list extended sheep allowed ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
  access-list INTERNAL-to-SITE1 extended permit ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
  access-list INTERNAL-to-training3 extended permitted ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
  access-list INTERNAL-to-SITE2 extended permit ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
  no pager
  Enable logging
  exploitation forest asdm warnings
  Debugging trace record
  Outside 1500 MTU
  MTU 1500 INTERNAL
  MTU 1500 COMMENTS
  192.168.11.1 mask - local 192.168.11.25 pool IN-HOUSE VPN IP 255.255.255.0
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 623.bin
  enable ASDM history
  ARP timeout 14400
  Global 1 interface (outside)
  (INTERNAL) NAT 0 access-list sheep
  NAT (INTERNAL) 1 0.0.0.0 0.0.0.0
  NAT (GUEST) 1 0.0.0.0 0.0.0.0
  5900 5900 Camille netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
  3389 3389 Apollo netmask 255.255.255.255 interface static tcp (INDOOR, outdoor)
  public static tcp (INDOOR, outdoor) interface www Apollo www netmask 255.255.255.255
  public static tcp (INDOOR, outdoor) interface https Apollo https netmask 255.255.255.255
  public static tcp (INDOOR, outdoor) interface smtp smtp Apollo netmask 255.255.255.255
  5901 puppy 5901 netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
  Access-group outside_access in interface outside
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  RADIUS protocol AAA-server Apollo
  Apollo (INTERNAL) AAA-server Apollo
  Timeout 5
  key *.
  AAA authentication enable LOCAL console
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  Enable http server
  http 0.0.0.0 0.0.0.0 INTERNAL
  http 0.0.0.0 0.0.0.0 COMMENTS
  No snmp server location
  No snmp Server contact
  Community SNMP-server
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
  Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-3DES-SHA TRANS_ESP_3DES_SHA
  correspondence address 1 card crypto outside_map INTERNAL SITE1
  card crypto outside_map 1 set of peer SITE1 - ASA
  card crypto outside_map 1 set of transformation-ESP-3DES-SHA
  address for correspondence card crypto outside_map 2 INTERNAL training3
  outside_map 2 peer training3 - ASA crypto card game
  card crypto outside_map 2 game of transformation-ESP-3DES-SHA
  address for correspondence outside_map 3 card crypto INTERNAL SITE2
  game card crypto outside_map 3 peers SITE2 - ASA
  card crypto outside_map 3 game of transformation-ESP-3DES-SHA
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  delimiter group @.
  Telnet training3 - ASA 255.255.255.255 outside
  Telnet SITE2 - ASA 255.255.255.255 outside
  Telnet SITE1 - ASA 255.255.255.255 outside
  Telnet 0.0.0.0 0.0.0.0 INTERNAL
  Telnet 0.0.0.0 0.0.0.0 COMMENTS
  Telnet timeout 60
  SSH enable ibou
  SSH training3 - ASA 255.255.255.255 outside
  SSH SITE2 - ASA 255.255.255.255 outside
  SSH SITE1 - ASA 255.255.255.255 outside
  SSH 0.0.0.0 0.0.0.0 INTERNAL
  SSH 0.0.0.0 0.0.0.0 COMMENTS
  SSH timeout 60
  Console timeout 0
  access to the INTERNAL administration
  Hello to tunnel L2TP 100
  interface ID client DHCP-client to the outside
  dhcpd dns 4.2.2.1 4.2.2.2
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  !
  address INTERNAL 192.168.10.100 dhcpd - 192.168.10.200
  dhcpd Apollo Odyssey interface INTERNAL dns
  dhcpd somewhere.com domain INTERNAL interface
  interface of dhcpd option 150 ip 10.1.1.40 INTERNAL
  enable dhcpd INTERNAL
  !
  dhcpd address 192.168.2.100 - 192.168.2.200 COMMENTS
  dhcpd dns 4.2.2.1 4.2.2.2 interface COMMENTS
  enable dhcpd COMMENTS
  !

  a basic threat threat detection
  statistical threat detection port
  Statistical threat detection Protocol
  Statistics-list of access threat detection
  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
  NTP server 192.43.244.18 prefer external source
  WebVPN
  allow outside
  CSD image disk0:/securedesktop-asa-3.4.2048.pkg
  SVC disk0:/sslclient-win-1.1.4.179.pkg 1 image
  SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 2 image
  enable SVC
  Group Policy DefaultRAGroup INTERNAL
  attributes of Group Policy DefaultRAGroup
  Server DNS 192.168.10.4 value
  Protocol-tunnel-VPN l2tp ipsec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com
  Group Policy DefaultWEBVPNGroup INTERNAL
  attributes of Group Policy DefaultWEBVPNGroup
  VPN-tunnel-Protocol webvpn
  Group Policy DefaultL2LGroup INTERNAL
  attributes of Group Policy DefaultL2LGroup
  Protocol-tunnel-VPN IPSec l2tp ipsec
  Group Policy DefaultACVPNGroup INTERNAL
  attributes of Group Policy DefaultACVPNGroup
  VPN-tunnel-Protocol svc
  attributes of Group Policy DfltGrpPolicy
  value of 192.168.10.4 DNS Server 4.2.2.2
  VPN - 25 simultaneous connections
  VPN-idle-timeout no
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com
  the value INTERNAL VPN address pools
  chip-removal-disconnect disable card
  WebVPN
  SVC keepalive no
  client of dpd-interval SVC no
  dpd-interval SVC bridge no
  value of customization DfltCustomization
  attributes global-tunnel-group DefaultRAGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultRAGroup
  IPSec-attributes tunnel-group DefaultRAGroup
  pre-shared-key *.
  Disable ISAKMP keepalive
  tunnel-group DefaultRAGroup ppp-attributes
  No chap authentication
  no authentication ms-chap-v1
  ms-chap-v2 authentication
  attributes global-tunnel-group DefaultWEBVPNGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultWEBVPNGroup
  tunnel-group 123.234.8.60 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.60
  pre-shared-key *.
  tunnel-group 123.234.8.124 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.124
  pre-shared-key *.
  tunnel-group 123.234.8.189 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.189
  pre-shared-key *.
  type tunnel-group DefaultACVPNGroup remote access
  attributes global-tunnel-group DefaultACVPNGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultACVPNGroup
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the http
  inspect the they
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:423c807c0d63cb3e9aeceda977053f84
  : end
  ASDM image disk0: / asdm - 623.bin
  ASDM location Camille 255.255.255.255 INTERNAL
  ASDM location INTERNAL CGT-external 255.255.255.255
  ASDM location INTERNAL SITE1-LAN 255.255.0.0
  ASDM location INTERNAL SITE2-LAN 255.255.0.0
  ASDM location INTERNAL training3-LAN 255.255.0.0
  ASDM location INTERNAL training3 - ASA 255.255.255.255
  ASDM location INTERNAL GDO 255.255.255.255
  ASDM location INTERNAL SITE1 - ASA 255.255.255.255
  ASDM location INTERNAL SITE2 - ASA 255.255.255.255
  ASDM location INTERNAL training3-VOICE 255.255.0.0
  ASDM location puppy 255.255.255.255 INTERNAL
  enable ASDM history

  I should also mention that my test clients are a combination of Windows XP, Windows 7, and Windows Mobile. Other that in specifying the preshared key and forcing L2TP/IPsec on the client side, the VPN settings on clients are the default settings with the help of MS-CHAP/MS-CHAPv2.

  You must configure * intercept-dhcp enable * in your group strategy:

  attributes of Group Policy DefaultRAGroup

  attributes of Group Policy DefaultRAGroup

  Server DNS 192.168.10.4 value
  Protocol-tunnel-VPN l2tp ipsec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com

  Intercept-dhcp enable

  -Latptop VPN clients (which I assume are on windows computers) is also the * use on remote network default gateway * box unchecked.  It is located on the Advanced tab of VPN client TCP/IP properties.   Select Client VPN > properties > Networking > TCP/IP Internet Protocol > properties > advanced and uncheck the box.

  Alex

• problem of traffic flow with tunnel created the network with a tunnel to a VPN concentrator

  Hi, I worked with Cisco and the seller for 2 weeks on this.II am hoping that what we are witnessing will ring a Bell with someone.

  Some basic information:

  I work at a seller who needs from one site to the other tunnel.  There are currently 1 site to another with the seller using a Juniper SSG, which works without incident in my system.  I'm transitioning to routers Cisco 2811 and put in place a new tunnel with the seller for the 2800 uses a different public ip address in my address range.  So my network has 2 tunnels with the provider that uses a Cisco VPN concentrator.  The hosts behind the tunnel use 20x.x.x.x public IP addresses.

  My Cisco router will create a tunnel, but I can't not to hosts on the network of the provider through the Cisco 2811, but I can't get through the tunnel of Juniper.  The seller sees my packages and provider host meets them and sends them to the tunnel.  They never reach the external interface on my Cisco router.

  I'm from the external interface so that my endpoint and the peers are the same IP address.  (note, I tried to do a static NAT and have an address of tunnel and my different host to the same result.)  Cisco has confirmed that I do have 2 addresses different and this configuration was a success with the creation of another successful tunnels toa different network.)

  I tested this configuration on a network of transit area before moving the router to the production network and my Cisco 2811 has managed to create the tunnel and ping the inside host.  Once we moved the router at camp, we can no longer ping on the host behind the seller tunnel.   The seller assured me that the tunnel setting is exactly the same, and he sees his host to send traffic to the tunnel.  The seller seems well versed with the VPN concentrator and manages connections for many customers successfully.

  The seller has a second VPN concentrator on a separate network and I can connect to this VPN concentrator with success of the Cisco 2811 who is having problems with the hub, which has also a tunnel with Gin.

  Here is what we have done so far:

  (1) confirm the config with the help of Cisco 2811.  The tunnel is up.  SH cyrpto ipa wristwatch tunnel upward.
  (2) turn on Nat - T side of the tunnel VPN landscapers
  (3) confirm that the traffic flows properly a tunnel on another network (which would indicate that the Cisco config is ok)
  (4) successfully, tunnel and reach a different configuration hosting
  (5) to confirm all the settings of tunnel with the seller
  (6) the seller confirmed that his side host has no way and that it points to the default gateway
  (7) to rebuild the tunnel from scratch
  8) confirm with our ISP that no way divert traffic elsewhere.  My gateway lSP sees my directly connected external address.
  (9) confirm that the ACL matches with the seller
  (10) I can't get the Juniper because he is in production and in constant use

  Is there a known issue with the help of a VPN concentrator to connect to 2 tunnels on the same 28 network range?

  Options or ideas are welcome.  I had countless sessions with Cisco webex, but do not have access to the hub of the seller.  I can forward suggestions.

  Here's a code

  crypto ISAKMP policy 1
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 2
  BA 3des
  preshared authentication
  Group 2

  Crypto ipsec transform-set mytrans aes - esp esp-sha-hmac

  Crypto-map dynamic dynmap 30
  Set transform-set RIGHT

  ISAKMP crypto key address No.-xauth

  interface FastEthernet0/0
  Description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE $ 0/0
  IP 255.255.255.240
  IP access-group 107 to
  IP access-group out 106
  NAT outside IP
  IP virtual-reassembly
  route IP cache flow
  automatic duplex
  automatic speed
  crypto mymap map

  logging of access lists (applied outside to get an idea of what will happen.  No esp traffic happens, he has never hits)

  allowed access list 106 esp host host newspaper
  106 ip access list allow a whole
  allowed access list 107 esp host host Journal
  access-list 107 permit ip host host Journal

  access-list 107 permit ip host host Journal
  107 ip access list allow a whole

  Crypto isa HS her
  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
    QM_IDLE ASSETS 0 1010

  "Mymap" ipsec-isakmp crypto map 1
  Peer =.
  Extend the 116 IP access list
  access - list 116 permit ip host host (which is a public IP address))
  Current counterpart:
  Life safety association: 4608000 kilobytes / 2800 seconds
  PFS (Y/N): N
  Transform sets = {}
  myTrans,
  }

  OK - so I have messed around the lab for 20 minutes and came up with the below (ip are IP test:-)

  (4) ip nat pool crypto-nat 10.1.1.1 10.1.1.1 prefix length 30 <> it comes to the new address of NAT

  !
  (1) ip nat inside source list 102 interface FastEthernet0/0 overload <> it comes to the interface by default NAT

  !
  IP nat inside source map route overload of crypto-nat of crypto-nat pool <> it is the policy of the NAT function

  !

  (6) access-list 101 permit ip 172.16.1.0 0.0.0.255 172.16.2.0 0.0.0.255 <> defines the IP source and destination traffic

  !

  (2) access-list 102 deny ip 172.16.1.0 0.0.0.255 172.16.2.0 0.0.0.255 <> does not NAT the normal communication

  (3) access-list 102 deny ip 10.1.1.1 host 172.16.2.0 0.0.0.255 <> does not re - NAT NAT

  (1) access-list 102 permit ip 172.16.1.0 0.0.0.255 any <> allows everyone else to use the IP Address of the interface for NAT

  !

  (5) crypto-nat route-map permit 5 <> condition for the specific required NAT
  corresponds to the IP 101 <> game of traffic source and destination IP must be NAT'td

  (7) access list 103 permit ip 10.1.1.1 host 172.16.2.0 0.0.0.255 <> crypto acl

  Then, how the works above, when a package with the what IP 172.16.1.0/24 source wants to leave the router to connect to google, say the source will change to IP interface (1).  When 172.16.1.0/24 wants to talk to172.16.2.0/24, it does not get translated (2).  When the remote end traffic equaled the following clause of NAT - the already NAT'td IP will not be affected again (3) when a host 172.16.1.0/24 wants to communicate with 172.16.2.20/24 we need a NAT NAT specific pool is required (4).  We must define a method of specific traffic to apply the NAT with a roadmap (5) which applies only when the specific traffic (6), then simply define the interesting traffic to the VPN to initiate and enable comms (7) corresponding