How to read the output of vm-support

Similar Questions

• How to read the papers of ucs tech support

  Hi team

  Can you please tell me how to read the newspapers of ucs tech support to find out hardware problems

  Greetings.

  Your question is probably something that is difficult to address in this format.

  Hardware and firmware is so rapidly changing, so are the various capabilities of diagnosis (and how, when, where they write to newspapers).  I think that it would be virtually impossible to maintain a full guide updated content of tech support file and how to interpret them.

  That being said, there are some more frequent for both blade/UCSM and stand alone C series servers such as SALT that connects usually record the major mistakes such as chess DIMM, HD failures, etc.

  There are general troubleshooting guides such as http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ts/guide/UCSTroubleshooting/UCSTroubleshooting_chapter_0111.html

  There are also courses that correspond to the review DCUCT 642 - 035 http://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/dcuct.html entering some details by looking at newspapers, among other things.

  Is there some hardware problems that you try searching?  You have some sort of polling app that parses the files you are trying to Setup alerts for, etc.?

  Thank you

  Kirk

• How to read the two columns of data from the Port series

  Hello

  I'm reading two columns of data from the serial port.

  Example:

  52439 52430

  52440 52437

  52209 52214

  51065 51070

  52206 52390

  I use the serial of Visa service and I can read the first column of data from the serial port, but I can't understand how to read the second column.

  I want to both sets of chart data.

  I enclose my VI.

  Thank you for your help.

  The analysis of string function takes a "Format string" on top (with the right button of the function and choose Help, which explains all the entries).  In particular, you can say 'Give me two numbers separated by a tab' and the output will be two numbers (whole or floating, depending on the chosen format).  In particular, %d\t%d specifies a decimal integer, , whole decimal.

• How to store the output of a statement select * statement in a file?

  How to store the output of a statement select * / statement of dsc in a file?

  As user sys:

  CREATE OR REPLACE DIRECTORY TEST_DIR AS '\tmp\myfiles'
  /
  GRANT READ, WRITE ON DIRECTORY TEST_DIR TO myuser
  /
  

  As myuser:

  CREATE OR REPLACE PROCEDURE run_query(p_sql IN VARCHAR2
                                       ,p_dir IN VARCHAR2
                                       ,p_header_file IN VARCHAR2
                                       ,p_data_file IN VARCHAR2 := NULL) IS
    v_finaltxt  VARCHAR2(4000);
    v_v_val     VARCHAR2(4000);
    v_n_val     NUMBER;
    v_d_val     DATE;
    v_ret       NUMBER;
    c           NUMBER;
    d           NUMBER;
    col_cnt     INTEGER;
    f           BOOLEAN;
    rec_tab     DBMS_SQL.DESC_TAB;
    col_num     NUMBER;
    v_fh        UTL_FILE.FILE_TYPE;
    v_samefile  BOOLEAN := (NVL(p_data_file,p_header_file) = p_header_file);
  BEGIN
    c := DBMS_SQL.OPEN_CURSOR;
    DBMS_SQL.PARSE(c, p_sql, DBMS_SQL.NATIVE);
    d := DBMS_SQL.EXECUTE(c);
    DBMS_SQL.DESCRIBE_COLUMNS(c, col_cnt, rec_tab);
    FOR j in 1..col_cnt
    LOOP
      CASE rec_tab(j).col_type
        WHEN 1 THEN DBMS_SQL.DEFINE_COLUMN(c,j,v_v_val,2000);
        WHEN 2 THEN DBMS_SQL.DEFINE_COLUMN(c,j,v_n_val);
        WHEN 12 THEN DBMS_SQL.DEFINE_COLUMN(c,j,v_d_val);
      ELSE
        DBMS_SQL.DEFINE_COLUMN(c,j,v_v_val,2000);
      END CASE;
    END LOOP;
    -- This part outputs the HEADER
    v_fh := UTL_FILE.FOPEN(upper(p_dir),p_header_file,'w',32767);
    FOR j in 1..col_cnt
    LOOP
      v_finaltxt := ltrim(v_finaltxt||','||lower(rec_tab(j).col_name),',');
    END LOOP;
    --  DBMS_OUTPUT.PUT_LINE(v_finaltxt);
    UTL_FILE.PUT_LINE(v_fh, v_finaltxt);
    IF NOT v_samefile THEN
      UTL_FILE.FCLOSE(v_fh);
    END IF;
    --
    -- This part outputs the DATA
    IF NOT v_samefile THEN
      v_fh := UTL_FILE.FOPEN(upper(p_dir),p_data_file,'w',32767);
    END IF;
    LOOP
      v_ret := DBMS_SQL.FETCH_ROWS(c);
      EXIT WHEN v_ret = 0;
      v_finaltxt := NULL;
      FOR j in 1..col_cnt
      LOOP
        CASE rec_tab(j).col_type
          WHEN 1 THEN DBMS_SQL.COLUMN_VALUE(c,j,v_v_val);
                      v_finaltxt := ltrim(v_finaltxt||',"'||v_v_val||'"',',');
          WHEN 2 THEN DBMS_SQL.COLUMN_VALUE(c,j,v_n_val);
                      v_finaltxt := ltrim(v_finaltxt||','||v_n_val,',');
          WHEN 12 THEN DBMS_SQL.COLUMN_VALUE(c,j,v_d_val);
                      v_finaltxt := ltrim(v_finaltxt||','||to_char(v_d_val,'DD/MM/YYYY HH24:MI:SS'),',');
        ELSE
          v_finaltxt := ltrim(v_finaltxt||',"'||v_v_val||'"',',');
        END CASE;
      END LOOP;
    --  DBMS_OUTPUT.PUT_LINE(v_finaltxt);
      UTL_FILE.PUT_LINE(v_fh, v_finaltxt);
    END LOOP;
    UTL_FILE.FCLOSE(v_fh);
    DBMS_SQL.CLOSE_CURSOR(c);
  END;
  

  This allows the header line and the data to write into files separate if necessary.

  for example

  SQL> exec run_query('select * from emp','TEST_DIR','output.txt');
  
  PL/SQL procedure successfully completed.
  

  Output.txt file contains:

  empno,ename,job,mgr,hiredate,sal,comm,deptno
  7369,"SMITH","CLERK",7902,17/12/1980 00:00:00,800,,20
  7499,"ALLEN","SALESMAN",7698,20/02/1981 00:00:00,1600,300,30
  7521,"WARD","SALESMAN",7698,22/02/1981 00:00:00,1250,500,30
  7566,"JONES","MANAGER",7839,02/04/1981 00:00:00,2975,,20
  7654,"MARTIN","SALESMAN",7698,28/09/1981 00:00:00,1250,1400,30
  7698,"BLAKE","MANAGER",7839,01/05/1981 00:00:00,2850,,30
  7782,"CLARK","MANAGER",7839,09/06/1981 00:00:00,2450,,10
  7788,"SCOTT","ANALYST",7566,19/04/1987 00:00:00,3000,,20
  7839,"KING","PRESIDENT",,17/11/1981 00:00:00,5000,,10
  7844,"TURNER","SALESMAN",7698,08/09/1981 00:00:00,1500,0,30
  7876,"ADAMS","CLERK",7788,23/05/1987 00:00:00,1100,,20
  7900,"JAMES","CLERK",7698,03/12/1981 00:00:00,950,,30
  7902,"FORD","ANALYST",7566,03/12/1981 00:00:00,3000,,20
  7934,"MILLER","CLERK",7782,23/01/1982 00:00:00,1300,,10
  

  The procedure allows for the header and the data to separate files if necessary. Just by specifying the file name "header" will put the header and the data in a single file.

• How to read the files on time capsule

  How to read the files on time capsule from iPad?

  Thank you

  Using an application like navigation on the iPad. More info here:

  Stratospherix - FileBrowser - overview

• How to read the status of User1 DIP-switch with a cRIO FPGA chassis?

  How to read the State of the DIP switches on a FPGA cRio chassis?

  I work with a cRIO 9022... My idea is to put the system in "service" mode with USER1 switch to IT and communicate with the FPGA via the FPGA - GUI (VI) on the host computer instead via the RT module that is used in normal conditions.

  Any ideas? Unfortunately, I don't have an unused channel on the left... .and (as I know) cannot use the interface RS232 of FPGA.

  Many thanks in advance,

  Luke

  Hi, this is the correct information. You cannot read the FPGA of DIP-switch status. The only thing you could do is to use the function of Reading Switch.vi located under the range of functions-> real-> utilities RT time

  It's how you probably know side host RT and not the FPGA.

  Cordially Virginia

• How to read the value of list boxes by iteration in a loop For?

  I have a lot of list boxes on the front of my VI. I want to know how to read the value of this combo with a loop boxes For. The point is that I don't know how to get the reference of each combo box in a loop.

  Any information would be welcome. Thank you!

  su27 wrote:

  I have a lot of combo boxes on the front of my VI [...]

  

  Be sure to close the references that you have finished with them.

• How to read the VI Analyzer config file?

  Hello

  How to read the analuzer vi configuration file? I'm getting a lot of errors on the size of the front panel and I don't know what should be the size you want. Where is the maximum expected size of the specified front panel?

  Kaspar says:

  Hello

  How to read the analuzer vi configuration file? I'm getting a lot of errors on the size of the front panel and I don't know what should be the size you want. Where is the maximum expected size of the specified front panel?

  If you have VI Analyzer installed, you can load the configuration file and look at the section select the Tests. There is a test for the maximum size of front under front-> User Interface. The default value is the resolution of the current monitor of the PC (including multiple monitors). You can change to the desired option.

• read the output of a path of analog output current voltage

  In DAQmx if you are unsure of the status of a digital output port, you can take a reading on this subject.  When I try this on an analog output, I get an error.  Is it possible to query the status of the output of an analog output?  I realize that I could follow the State with a variable, but a direct reading would be really handy.

  Hello, GIS.

  There is no way to read the output in the AO modules without wiring physically the signal to a module to HAVE.  You are able to use a variable to read the current value of the output, as you mentioned earlier.

  Channels AO multifunction boards, however, can be read through tasks of entry by rounting in-house channel to read ao vs aoground.

  Lisa

• How to read the date and time of a file by labview information

  How to read the date and time of a file by labview information? for example, time created and updated time.

  The similar question had already spoken here (this is the old thread but still seems topical):

  http://forums.NI.com/T5/LabVIEW/file-date-created/TD-p/109836

• Read the output values after each step runs in the User Interface of LabVIEW

  Hi all

  Development environment: TestStand 2010 SP1 and LabVIEW 2010 SP1

  Problem: is there a way to run the following steps programmatically and get values out of each of them?

  I have already extended a bit a complete interface IO for TestStand load any sequence, choose among the measures and execute step by step (something as an alternative to the steps run selected). What I'm trying to do is to add some actions between each step and do in the UI (I can't change the sequence!), so I start the NewExecution with some previously configured InteractiveArgsParam and option breakAtFirstStep set to true. Eventually I do just something like step over when debugging the sequence and it works well, but I didn't do well a way yet to read the output values of the place...

  So, if I wait before the end of the run I can read my results by treating the ResultObject, but it works only after the completion of the test sequence. Because I wanted to stop after each step, read the values, do some actions and continue to the next step, I've tried to register a running Trace event reminder View Manager. I see that after each step is executed, this event is fired, but when I try to read that a ResultObject returned in the event data it is not filled with values (ResultList seems to be empty?). Is this a correct behavior or maybe I'm reading the wrong way? (It's the same VI regarding the reading of the ResultObjects after the sequence ends and there it works very well for tables, containers and other types of data).

  As I mentioned I can't change Test sequences, I can not add a UImessages.

  What are my options? If the trace event returns output all the values from each steps or is it just used to check the status? Or maybe there's a completely different approach to this issue?

  Thanks in advance for your suggestions,

  Best regards.

  When you manipulate the UIMessage trace (you need this before the return of the event or you will present the race conditions), download myuimessage. Thread. Then call Thread.GetSequenceContext (0, & Iplease).

  And then on the context of the sequence, either go to PreviousStep.Result if it exists, or watch Locals.ResultList.

  Trace events occur between the steps executed step the more recently is the previous step, but it is also a trace event to the beginning before any measure have run at this time, there will be a previous step.

  Hope this helps,

  -Doug

• How to read the host name or serial number cRIO locally

  I have not worked with cRIO and decided to ask for help.  (o).

  I don't know about the screws that allow to access this information from a connected Windows machine, however, I want to retrieve and display this information on remote panels.  But I cannot determine how to read the cRIO hostname or the serial number of the software running on the cRIO?

  Thanks for the help.

  James

  This could help.

• How to read the color table in a subvi?

  How to read the color table in a subvi? Is it made by a reference to the table or with a global variable? For a better understanding of the problem, I added to vi. Run the "run.vi." I want to see

  the background color of the table "run.vi" in the subvi called "read color.vi".

  How can I do?

  Thanks in advance

  Norick

  pop up on the wire table refernece and establishes 'control '. Add this control to the icon of the sub - VI decision-making and then wire ref of the appellant to this Terminal VI so the calling VI move the ref to the Subvi.

  Ben

• How to read the 32-bit depth .bmp image

  How to read the image, 32-bit depth using LabVIEW .bmp?

  
  

• How to read the analog inputs of one Board of R for (PXI-7851R) series

  You can guide me please with the steps for reading of the analog inputs of a series a. card I use as the target fpga PXI-7851R.

  Have you looked at the examples provided with LabVIEW? There are examples showing how to read the analog inputs.