How to set up LAN on Equium M50

Similar Questions

• How to set up LAN wireless and wired for simultaneous operation

  I use a Lenovo thinkpad running windows XP. I want to set up an independent network so that I can connect my hardware for debugging. At the same time, I want to be able to access the corporate network using the wireless interface.  My autonomous network consists of a Belkin router that is to act as a DHCP server, my laptop connected to a port on the router and my test material connected to a different port on the router. My wireless interface is configured to connect to the corporate network. With wireless interface and the ethernet interface (wired) enabled, when I am doing a config ip, I see that the devices get valid IP address, corresponding to subnets, they connect to IE the ethernet port gets IP address 192.168.x.x 172.x.x.x IP poster wireless interface while. But I am not able to ping or access sites on the internet, I am able to ping the router Belkin on the independent network.

  However, if I go under network connections and disable the ethernet connection to the local network can access the internet and my business network. Similarly, if I disable the wireless connection and that you enable the ethernet connection, so I am able to ping the router only and not my test equipment connected on the same subnet.

  If I configure the (wired) ethernet network interface to use a static IP address in the pool of IP from the router Belkiin (who is also a DHCP server) and set the IP Address of the Belkin router as gateway, I can access all the other devices on this local subnet if and only if the wireless interface is disabled.

  The search for networks order is defined as the wireless and Ethernet.

  In my case, I need two interfaces to be active at the same time, as explained at the beginning. Appreciate any suggestions.

  Thank you.

  Hello

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

  Hope this information is useful.

• Equium M50-244 does not not to wake up on LAN

  A notebook Equium M50-244 does not meet the magic packet WOL.

  The BIOS settings are correct and show adapter LAN ENABLED, Wake on LAN: ENABLED.

  The sticker on the laptop and the original box gives a different MAC address to know what the device itself (ifconfig or lshw). No matter, the laptop does not account the magic packets for two MAC addresses.

  Using Wireshark, I see that the WOL packets are certainly diffuse with properly formatted MAC addresses.

  My thought is now that it is a BIOS problem but I can't find the right bios for this machine.

  What would be the best bios match? Keep in mind this box is Linux.

  Thanks in advance for any help.

  See you soon

  Nick

  Hello

  Have you checked if the WOL is enabled in the network card settings?
  Do you know how to check this?

  Go to the Device Manager, expand network adapter s and mark LAN card.
  Then, go to the properties of the network adapter and check the Advanced tab.

  There are a lot of different settings and a configuration option must refer to the WOL.

• Equium M50: How do I change the details of Wlan WEP?

  Does anyone know how to change the WEP (?) details on an Equium M50, I just signed up to broadband wireless Orange and they tell me that their WEP key is 26 digits and look only some old pc for 23 codes numbers? I can't put my wireless switch on and my laptop is wireless box but will pair not to her.

  Any help would be greatly appreciated I have a centrino laptop, a wireless box, a monthly bill of £18 and I still have to use a thread!

  See you soon,.
  Nick.

  Hello

  Available in two flavors, 64-bit and 128-bit static WEP. When you configure a channel key on access point or client device a hex (or ASCII) WEP came to represent the key.
  If you use WEP 128 bit, the user has entered the portion is 26 digits HEX (ASCII 13 characters)
  Encryption WEP 64-bit required 5 password alphanumeric characters numbers and 10-digit hexadecimal characters.

  I put t know what WLan application you use but generally if you have Atheros WLan card you should be able to change the encryption in the Atheros WLan utility.

  If you use Windows to configure the WiFi connection so in this case you must change under properties of the Wlan network.

• How Equium M50-235 faster?

  Hi all

  I've had my laptop Equium M50 - 235 for about 4 years now and although it's a bit slow :( I was wondering if anyone can suggest ways to make it faster because I don't want to buy a new laptop due to lack of money.

  It is 256 RAM and 1.7 GHz, 40g hard drive... Can I put them all?
  Advice & tips are welcome!

  Please help as I t really know what I m doing when it comes to things like that!
  Thank you very much

  Dale

  You can make your computer much faster satellite phone very easy.
  The first RAM upgrade to the maximum level. It is 2 GB. For this you need two modules of RAM 1 GB compatible.
  Compatible 1 GB has PA3313U-2M1G part number.

  With 2 GB of RAM, the laptop will be much faster. The second step is running in system optimization.

  You n t need some CPU upgrade. With RAM maximum and set up the operating system, the laptop runs like a rocket. ;)

• Equium M50 - how to replace the fan?

  Hi all.

  I don't know much about computers, and this is my first post. My Equium M50-192 starts to turn after about 15-20 minutes. It is very hot and I can't hear the fan more. I guess that's the problem so to replace the fan. But how can I do? How do the fan?
  And it is easy to do, or should I leave it to an expert?

  Thank you very much

  Hello

  It is not easy to explain in a few sentences. Computer laptop disassembly procedure is quite complicated and if you don t have experiences you should not even think about it.

  The second important thing is that laptop procedure disassembly should be done following the rights steps in Maintenance manuals. This document is not a public document.

  So if you think about it maybe you should seek professional help.
  What do you thing about that?

• How to install the compatible DVD decoder on Equium M50?

  My laptop is model Equium M50-164 PSM57E-002004AV

  After format, I lost DVD decoder.
  How can I install compatible DVD decoder?

  Can you please explain how you mean exactly and what OS do you have?
  You have reinstalled Windows using the Toshiba Recovery disk?

  Normally, you can play DVDs with Windows media player and so you n t need additional software or driver.
  Also, I prefer VLC media player. This little player can play audio and video files more and its freeware.

  If you need a codec pack that you should search with Google K-Lite Mega Codec Pack. It is very good ;)

  Good luck!

• Equium M50 - how to connect firewire devices?

  Equium M50 Intel Celeron M 360 1.4 GHz processor

  Referring to the above, I am able to download photos from my camera to my hard drive, but to download videos that I need to connect a firewire camcorder to the computer. There is no connector on the computer to take in this regard.

  Is there a solution to this?

  Hello

  I put t know if your camera has a firewire port, but if yes it is listed in the Device Manager as IEEE 1394 bus host controller.

  If your device doesn't have a firewire port, you can buy the PCMCIA card with firewire port. By the way: M50 has 4 USB ports (two in the back near LAN port and two near the DVD drive on the right). On models with firewire ports it is definitively placed near S-video output port as Michael described.

  Good bye

• Equium M50 will not recognize the LAN port - error: disconnected network cable

  I own a Toshiba Equium M50 and have problems with the Marvell Yukon 88E8036 PCI-E Fast Ethernet Controller.

  I used to connect through a Modem/DSL switch "ADDON" and had no problems. I then replaced the ADDON with an ADSL Modem/Router "NETGEAR" DG834G to win the wireless port, and since that time my machine won't recognise the LAN port. .

  I know that cables are OK I used with other phones and had no problems. I can also plug a PCI card to connect without any problems. It seems to me that if the Marvell Yukon 88E8036 PCI-E Fast Ethernet Controller has a problem with the netgear Modem/Router.

  Anyone out there with a similar experience and some tips/suggestions?

  PLEASE

  Hello

  For me this doesn't show t as a problem of LAN card but your router is a problem.
  Check Device Manager if the network card is correctly recognized. If there is no yellow exclamation point, so all is ok!
  You can try to remove the network adapter from Device Manager and reboot after new install driver LAN again.

  The question has looked after installing or connecting the new Netgear modem router.
  I would recommend to check first the settings or update the firmware on this router.

  I found more useful websites
  http://compnetworking.about.com/od/WindowsNetworking/f/cableunplugged.htm

  http://www.experts-exchange.com/Networking/broadband/DSL_Cable/Q_20381405.html

• How to set up a Lan to Lan VPN without using your external IP address?

  I have two 28 subnets A & B.

  My PIX and ASA outside interface addresses are both in A subnet.

  I am in the middle of a migration of the PIX to ASA and need to use the PIX outside of the address of the interface on the ASA for the last two remaining lan to lan VPN.

  I do like that because the sellers of these virtual private networks to connect to are huge dinosaurs IT and the aaages to get their sh * t tri... This means that I have to pass the IP address to my ASA, so I can't sentence have change for a new IP peer.

  I tried to figure out how to set a specific my counterpart VPN IP address but I can't figure out how...

  I even physically connected a second ethernet port and tried to give a similar IP in the same range, which it says it is not possible to have both outside the IP addresses on the same subnet.

  Hello

  It is not possible to have an IP address "secondary" on the physics/logic interface of a Cisco firewall.

  And as you've noticed, you cannot configure the same subnet on 2 different interface either.

  We are talking about such a large configuration that you want to just migrate from completely to the ASA PIX and make a switch during a maintenance window?

  Couldn't you just pass the ASAs 'outside' IP address address to that on the PIX and move the ASAs 'outside' of the PIX? Or not the ASAs "outside" IP address already some configured related to what makes this impossible?

  -Jouni

• How to reset my Equium M50-192 to factory settings?

  Hi, I'm looking for some advice on my laptop.

  My laptop is a Toshiba Equium M50-192 and I would like to reset to the factory settings (on the box).

  I was advised by a friend that I need a recovery disk, but I don't seem to have one. Again, I have everything that came with the laptop when I bought it and have the different discs that came with it, but no recovery disk and have not been able to find the information I need the user manual.

  Is there a way I can reset my laptop without a disc?

  Any information or advice would be greatly appreciated.

  > Is there a way I can reset my laptop without a disc?
  It is not possible to reset to factory without reinstall drive settings. You have only one option: get Microsoft WXP installation disc and install the version of the OS.

  All the drivers, which you can download from the Toshiba support page.
  You can also try, it is to find if someone has the original disc of recovery for this machine and ask if you can get a copy.

• How to set up a wired LAN on a Wrt320n?

  Hello, I have a router Wrt320n, and it is connected to 2 desktops through cables of cable.

  a computer is Windows XP, and the other has Windows 7.

  Both computers receive the Internet connection and are visible to the router, but the two computers cannot interact with each other.

  Which means that we cannot share files or play multiplayer games between them.

  I would like to know how to set up a Local network for these two reasons.

  Thanks in advance.

  For sharing files between 2 calculates... Make sure that file and printer sharing is enabled... Also, make sure the computer are in the same workgroup... Default workgroup in Windows Vista has been renamed to WORKING group. In Windows XP, the default workgroup name is MSHOME...

  Also, see this link.

• Equium M50 - E-mail Message to update the WLAN driver

  Hello, I got this message. When I tried to check what is the right driver, I was told, there isn't one!
  Could someone please advise others that I wouldn't confuse my machine

  Thank you

  -Original Message-
  From:
  VOX
  Sent: Tuesday, March 18, 2008 09:41
  Topic: Site Web de Toshiba alert

  >
  >
  >
  >
  > Hello,
  >
  > Here is the latest software updates for your machine:
  >
  >
  > PC: Equium M50 (PSM59)
  > Type: Wireless Lan driver
  > Language: universal
  > Operating system: Windows XP
  >
  > Click on this link to read the full article.
  > http://uk.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_driver_details.jsp?ID=58122&OSID=10&drive rLanguage = 42 & selectedLanguage = 13 & driverCountry = 41 & selectedCountry = 8
  >
  > Click this link to find compatible drivers
  > http://uk.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp
  >
  > If you wish to unsubscribe from these alerts by e-mail, please click the link below to edit your profile on the Toshiba site.
  > http://uk.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/jsp/login.do
  >
  >
  >
  >
  >
  >

  There are not a lot of advice. WLAN new driver is available and if you want, you can update. If you are satisfied, how the WIFI network for the moment no one you don't have to do anything. Leave it as it is.

  WLAN drivers, you can find under http://aps.toshiba-tro.de/wlan/ and download whenever you want.

• Equium M50: 2200BG WLan - unable to connect to the internet

  Equium M50 / wireless 2200BG Pro / Wireless eircomNETOPIA router 1642 4640 eircom

  Hello

  I have Aproblem with my wireless connection

  When I go to network connection I have 3 parts:

  1-broadband: inside there is a connection to broadband in disconnected state

  2 - LAN or high speed internet: inside there are 3 parts:
  in connected state (wireless 2200 BG) wireless network connection
  connection to the local network in connected state (marvell yukon)
  connection 1394 (1394 network adapter) connected status

  3 - Assistant

  So, normally the wireless connection works. But when I unplug the ethernet cable the part with the LAN connection is not connected and I can't connect to the internet, even though the wireless is connected.

  Can someone help me?
  Thank you in advance

  Generally, it should be possible to set up the broadband connection data in the configuration of the router.
  This must be done to connect to internet.

  So if you have disconnected the LAN cable please check if the WLan switch lights and check the FN F8 key combination.
  Then check if you can see the SSID in the Wlan network connections.

• Recommended memory for Equium M50-164 does not fit

  I have the Equium M50-164 in its original configuration.

  I wanted to add more memory, so, on the recommendation of the Toshiba Product Support page, I bought the Toshiba PA3411S-2M1G memory (from eBuyer) module.

  http://UK.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/JSP/individualOptions.do?service=UK&OPTION_ID=118626&t oshibaShop = true & SelCategorie = 4700

  Trying to mount the module of memory in my machine, I found that it is not! 'Separator' plastic between the two contacts on the laptop computer does not match the position of the notch between the two sets of pins on the memory module.

  Tosh recommends part number: PA3411S - 2M1G 1024 MB (1 GB) memory PC2-4300 (533 MHz) DDR2

  The memory that's happened has PA3411S-2M1G 1024 MB (1 GB) PC2-4200 (533 MHz) DDR2 memory on the box.

  Someone in the forums said that PC2700 PA3313U-2M1G is the part number.

  The manual supplied with the M50 means memory PC2700 .

  Anyone know the number, or an alternative appropriate by another manufacturer?

  I am very annoyed, as hotline support suggested, I phone their sales department! So they can sell me more wrong memory strips? Now look forward how the glove of returns with eBuyer...

  See you soon,.

  Andy

  Try here... http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=20384&ft=m&st=3