How to use ACS 5.2 to create a static ip address user for remote access VPN
Hi all
I have the problem. Please help me.
Initially, I use ACS 4.2 to create the static ip address for VPN remote access user, it's easy, configuration simply to the user defined > address assignment IP Client > assign the static IP address, but when I use ACS 5.2 I don't ' t know how to do.
I'm trying to add the IPv4 address attribute to the user to read "how to use 5.2 ACS", it says this:
1Ajouter step to attribute a static IP address to the user attribute dictionary internal:
Step 2select System Administration > Configuration > dictionaries > identity > internal users.
Step 3click create.
Static IP attribute by step 4Ajouter.
5selectionnez users and identity of the stage stores > internal identity stores > users.
6Click step create.
Step 7Edit static IP attribute of the user.
I just did, but this isn't a job. When I use EasyVPN client to connect to ASA 5520, user could the success of authentication but will not get the static IP I set up on internal users, so the tunnel put in place failed. I'm trying to configure a pool of IP on ASA for ACS users get the IP and customer EasyVPN allows you to connect with ASA, everything is OK, the user authenticates successed.but when I kill IP pool coufigurations and use the "add a static IP address to the user 'configurations, EzVPN are omitted.
so, what should I do, if anyboby knows how to use ACS 5.2 to create a user for ip address static for remote access VPN, to say please.
Wait for you answer, no question right or not, please answer, thank you.
There are a few extra steps to ensure that the static address defined for the user is returned in the Access-Accept. See the instuctions in the two slides attached
Tags: Cisco Security
Similar Questions
-
How can I assign the static fixed IP for remote access VPN users
Hi team,
I have a requirement to assign a fixed static IP users VPN remote access in ASA, please help how I can achice this
Thanks in advance
Mikaelusername user1 attributes
VPN-framed-ip-address 10.200.115.78 255.255.0.0
-
Remote access VPN with ASA 5510 by using the DHCP server
Hello
Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?
I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:
!
ASA Version 8.2 (5)
!
interface Ethernet0/1
nameif inside
security-level 100
IP 10.6.0.12 255.255.254.0
!
IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)
!
Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
!
Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dyn1 1jeu transform-set FirstSet
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap map crypto inside interface
crypto ISAKMP allow inside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
!
VPN-addr-assign aaa
VPN-addr-assign dhcp
!
internal group testgroup strategy
testgroup group policy attributes
DHCP-network-scope 10.6.192.1
enable IPSec-udp
IPSec-udp-port 10000
!
username testlay password * encrypted
!
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
strategy-group-by default testgroup
DHCP-server 10.6.20.3
testgroup group tunnel ipsec-attributes
pre-shared key *.
!
I got following output when I test connect to the ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO
4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048)
, : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740)
, : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80
Kind regards
Lay
For the RADIUS, you need a definition of server-aaa:
Protocol AAA - NPS RADIUS server RADIUS
AAA-server RADIUS NPS (inside) host 10.10.18.12
key *.
authentication port 1812
accounting-port 1813
and tell your tunnel-group for this server:
General-attributes of VPN Tunnel-group
Group-NPS LOCAL RADIUS authentication server
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
How have use ACS supported wireless users and the VPN user?
I'm new to ACS and configure the following requirement:
(1) ACS to authenticate users wireless with window AD.
(2) once connected successfully to the radio, the user must use VPN for remote access with the ASA.
(3) the end-user will have only 1 common username but different password.
for example:
username: password: cisco: cisco wireless.
username: cisco password: 1234 for VPN.
ACS support can this, if yes how can we do? Do I need 2 sets of ACS?
Yes, acs should work properly according to your need.
ACS, we have a feature called NAP "network access profile" where we can define the condition based on ip source or attributes which allow to say if the request comes from wireless device acs will forward to AD and if the request is of the acs VPN will forward to this diff of database.
Basically, we need to use two acs database.
Kind regards
~ JG
Note the useful messages
-
How do use ACS to enycrption for his backup?
How do use ACS to enycrption for its backup system?
Bruce,
GBA backup is encrypted with 40 RC2 - RC2 40-bit encryption method. Encryption
option to encrypt more data already encrypted for transmission
between ACS and the ftp server.
Kind regards
~ JG
Note the useful messages
-
How to prohibit remote access vpn client to use the local DNS server
Hello
I'm on ASA5505 remote access vpn configuration.
Everything works fine so far, except when the client got connected, he always used the local DNS server provided by the ISP. How can I force the customer to use the DNS server configured on ASA?
Thank you.
Kind regards
The command "Activate dns split-tunnel-all" is supported only on SSL VPN and VPN IKEv2. Since you're using IKEv1, this command is not supported.
Here's the order reference:
http://www.Cisco.com/en/us/docs/security/ASA/asa82/command/reference/S8.html#wp1533793
You configure no split tunnel? If you are, then you need to configure "tunnelall" split tunnel policy, and that will force the dns resolution and everything else through the VPN tunnel.
-
Configuration remote access VPN (IPSec) using FULL domain name
Hi friends of Cisco,
We have the DNS (only the internal IP) within our network, right now that we have configured VPN for remote access using public IP address and connect us with the same public IP address. I need help to use the domain name FULL rather than use public IP.
Can you please provide the configuration for this.
Feature: ASA 5520
Type of configuration: IPSec
Thank you
Estel
Hi Philippe,.
You can use one of the free Web of DNS dynamic sites and configure ASA to dynamic DNS.
Reference - http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/basic_ddns.html
HTH,
-Dieng
-
Implementation of the remote access VPN IPSec using SRI 2801
Hello
I tried to set up a VPN for remote access using 2801 SRI. I've been able to establish my house vpn tunnel using the DSL (behind a NAT) connection, give it SRI the IP address that is in the ip pool I configured on safety. The problem I have right now is that it does not reach the company LAN network.
DIAGRAM:
MODEM PC (VPN CLIENT) ADSL - ROUTER SOHO - INTERNET - ISR2801 - LAN---(10.10.0.27&192.168.0.9) COMPANY
PC: 172.16.10.122
SOHO ROUTER LAN IP: 172.16.10.254
SOHO ROUTER WAN IP: Dynamically assigned by ISP
ISR2801 WAN IP: x.x.x.5/224
IP LAN ISR2801: 10.10.0.50/24
The CORPORATE LAN subnet: 10.10.0.0/24 and 192.168.0.9/24
2801 SRI CONFIGURATION:
AAA new-model
!
!
connection of AAA NOCAUTHEN group local RADIUS authentication
local NOCAUTHOR AAA authorization network
!
!
IP domain name xxxxx.com
!
!
!
username root password 7 120B551806095F01386A
!
!
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
ISAKMP crypto 5 40 keepalive
ISAKMP crypto nat keepalive 20
!
Configuration group isakmp crypto-GROUP NOC client
touch [email protected]/ * /! ~ $ 9876 qwerty
DNS 192.168.0.9
192.168.0.9 victories
xxxxx.com field
LWOP-pool
include-local-lan
netmask 255.255.255.0
!
!
Crypto ipsec transform-set AC - SET esp-3des esp-sha-hmac
!
dynamic-map crypto NOC-DYNAMICMAP 10
transformation-LWOP-SET game
!
!
list of crypto AC-customer card NOCAUTHEN card authentication
list of crypto isakmp NOCAUTHOR AC-card card authorization
crypto map CNP-map client configuration address respond
Crypto map AC - map 10-isakmp dynamic ipsec AC-DYNAMICMAP
!
!
!
!
interface FastEthernet0/0
IP address x.x.x.5 255.255.255.224
Speed 100
full-duplex
card crypto AC-map
!
interface FastEthernet0/1
IP 10.10.0.50 255.255.255.0
Speed 100
full-duplex
!
local IP NOC-POOL 192.168.250.101 pool 192.168.250.110
IP route 0.0.0.0 0.0.0.0 XXX1
IP route 10.10.0.0 255.255.255.0 10.10.0.10
IP route 172.16.10.0 255.255.255.0 FastEthernet0/0
Route IP 192.168.0.0 255.255.255.0 10.10.0.10
IP route 192.168.250.0 255.255.255.0 FastEthernet0/0
!
I have attached a few screenshots. My goal here is to have access to my LAN to the company (10.10.0.0/24 and 192.168.0.9/24). I don't know what is missing here.
No, we don't need not NAT. wanted to confirm if NAT could cause this problem.
The config looks good. Can you ping routers ip internal interface the client LAN once it connects?
Are correct, w.r.t. transatlantic lines reaching pool behind router VPN?
If so, I would like to take a look at the exits following when a client is connected.
See the crypto eli
ISAKMP crypto to show his
Crypto ipsec to show his
SPSP
-
Im very new to Oracle DRM and Im trying to get the configuration of the application on the Windows Server that is running SQL Server 2008. When I try to connect to the Web Client I get this error.
DRM-61026: cannot create the session of the user for the following reason: the connection has failed. User name or password.
Can you please help
The problem is solved, reinstalled DRM and recreated the repository. the password has a symbol that causes the problem, @.
-
The use of Teamviewer for remote access to another PC from a PC
Hello
I have TWO PC, but unfortunately two PC has the same IP I checked ipconfig.
I called ISP regarding on the same IP between two PCs.
Is it possible that a PC can access second tool PC remotely using the Teamviewer software, even if TWO PC IP addresses are the same now?
Your comments will be appreciated.
Thank you
Hi Altman,
TeamViewer is a third party software. For support on the use of this product go to TeamViewer Support Center.
Note: software use of third parties, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.
-
The reason for this: British Colombia, I'm trying to port forward on my router 2wire AT & T. Everytime I turn my laptop off the IP reset and I can't do a check port on port forwarding, I did the day before. So I need a static IP address so that when I turn off my machine and then again on the INVESTIGATION period does not reset. Could I get a good suggestion on where to find this info.? I asked on other forums, but it seems that those who are not very active, and it's frustrating day waiting to get an answer lol. I really need my games to have a port before getting a low latency (ms). And also for download speeds appropriate downloading patches. Unfortunately, I do not know if my router 2wire has a UPnP enable/disable option of opening and closing ports properly. But I guess that even if it is not that I could always get the port forwarding to work. Thnx so you can really help me out here, I really appreciate it...
Also, I looked everywhere for the forums. I can't seem to find no to no the case, Idk where to go or what to do lol...
I thought about it, I had to use my routers IP address of my default gateway on my machine...
-
How to configure VPN 3000 Concentrator for remote access
I have inherited a VPN concentrator and want to configure it to provide remote access to my internal laboratory network when I'm traveling. Private interface is configured as 192.168.1.240/24. Public interface is configured as one of my public IP addresses. I have a public IP pool on the back side of a cable modem Roadrunner. I created a pool of addresses for clients such as 192.168.1.200 by 192.168.1.205. I created all group configurations, group and user base.
In the IP Routing tab, I see a default route pointing to my IP address of public gateway - the IP address of my box of roadrunner cable modem gateway.
Since my VPN client, I am able to connect to the VPN concentrator. I get an address from the pool and check the details of the tunnel under the statistics section shows IP address correct pool for the customer and the correct public IP address of my VPN reorga
Jeff,
According to statistics, it seems that the client sends traffic to the hub, but his answer not get back.
We need check the hub settings itself.
I need check the hub settings and that it is a GUI based device so I can't even ask to see the technology and the only option available is to WebEx.
You're ok with webex, pls lemme session comfortable time id and e-mail to send the invitation, it takes no more time and we will carry it out
Thank you
Ankur
-
Hi all!
About, what I'm trying to do is to create an entire virtual network. I'm working on and studying for my MCSE and wanted to create a virtual server and a few virtual desktops.
I wanted to put up a few roles on the server which (sort of) requires me to have a static IP address. My question is can I create something like a "static IP address make fun" to do?
I prefer not to pay the additional sum of $ my ISP for a static IP address if I have to. Other than this virtualization project, I don't need a static IP address.
Thank you!
Create and internal network, then NAT so they can talk to the internet.
-
How to use the clause type conditionally create new lines
This question is just for learning - no object other than to start real world to create versions of some queries known to learn how to measure the performance of the MODEL clause clause of the MODEL versions.
The question is: How can you write a STANDARD clause that pivots (updates) ONLY the lines that actually need to rotate and do NOT change the lines that have no value and cannot be rotated.
I found a good site that has about two dozen example articles on different pieces. This first link is the beginning of the series.
SQL features tutorials - Clause TYPE
http://www.sqlsnippets.com/en/topic-11663.html
This link is to a clause of FAQ of BluShadow MODEL version "how to convert rows to columns."
Line - MODEL method string
http://www.sqlsnippets.com/en/topic-11987.html
The solution to this link uses this line of source:
POSITION KEY VAL
--- ---------- ----------
R08 0 v1, v2, v3,.
and this result set:
POSITION KEY VAL
--- ---------- ----------
R08 1 v1
R08 2 v2
R08 3 v3
The reason why it produces that result set is this clause of the statement of MODEL
RETURN THE UPDATED LINES
If you comment on this article, you will see that the original lines are all in position 0. This means that the solution reproduced EACH SOURCE LINE even if there is only one item in the list of values.
Thus, even a line source with a single value (for example, the r01 'a') will be updated and updated this line is returned.
For a large number of data sources with only a few lines that actually need to rotate it would be a great performance of infringement.
This is the sample data source
with t as (button 1, 'a' value 'abc' col2, col3 'def' of the double
Select Union all 2, 'b', 'ghi', 'jkl' from dual
Union all select 3, 'c, d, e, 'mno', 'pqr' from dual.
Union all select 4, 'f', 'stu', 'vwx' from dual
)
Select the key, value, col2, col3
tKEY, VALUE, COL2, COL3
1, a, abc, def
2, b, GHI, jkl
3, "c, d, e, mno, pqr.
4, f, stu, vwxLines 1, 2 and 4 only have a value of (a, b, c respectively.
Only line 3 must rotate. It contains "c, d, e" and which must become 3 lines in the result set
Value of the key, col2 col3
1 an abc def
2B ghi jkl
3 c mno, pqr
3 d mno, pqr
3 e mno, pqr
4 f stu vwxThe nut of the problem is that if the clause 'RETURN UPDATED ROWS' is used, then the lines 1, 2 and 4 must be updated in order to be returned in the result set. And if this clause is NOT used, then line 3 must be updated by 'c', d, e 'c' and two new product lines: one line for a ' and one for 'e '.
How can you do this with the TYPE clause without the help of the clause "Return LINES UPDATE"? I don't have a solution to sample showing what I tried because I can't understand what it takes to even try.
I have a solution that uses "RETURN UPDATED ROWS" but I want to compare this performance to the exercise, when this clause is NOT used.
We ask BluShadow to add the solution of MODEL clause to this FAQ with other similar solutions.
Like this?
SQL > with t as
() 2
3 select the 1 key, 'a' val, 'abc' col2, col3 'def' of the double
Select 4 Union all 2, 'b', 'ghi', 'jkl' from dual
5 union all select 3, 'c, d, e, 'mno', 'pqr' from dual.
Select 6 Union all the 4 'f', 'stu', 'vwx' from dual
7)
8. Select the key
9, key_1
10, val
11, regexp_substr (val, ' [^,] +', 1, key_1) val_new
12, col2
13, col3
14 t
model 15
16 partition by (key)
dimension (1 key_1) 17
18 measures (val, col2, col3, (length (val) - length (replace (val, ",")) + 1) as len)
19 rules
(20)
21 val [for 1 to increment of len key_1 [1] 1] = val [1]
22, col2 [for 1 to increment of len key_1 [1] 1] = col2 [1]
23, col3 [for 1 to increment of len key_1 [1] 1] = col3 [1]
24)
25 order
26 by key
27, key_1;KEY KEY_1 VAL VAL_N NECK NECK
---------- ---------- ----- ----- --- ---
1 1 has an abc def
2 b 1 b ghi jkl
3 1 c, d, e c mno pqr
3 2 c, d, e d mno pqr
3 3 c, d, e e mno pqr
4 1 f f stu vwx6 selected lines.
-
I now find solutions 'adobe only' in this forum or anywhere online.
I'm sure there must be a way to create a flipbook using my catalog PDF and then export the animation into HTML 5 and points on my site so I hope that someone here could offer advice?
I know there are plugins and things you need to buy there, but spend a lot on Adobe products already, I want to continue those programs as a possible option first.
I think I could manually create an in Adobe animate, then export as HTML 5 animation with click on functions, forward, backward and to zoom in and zoom out.
All the tips are greatly appreciated.
Thank you!
Google best Flipbook jquery plugins
20 best jQuery Plugins Flipbook | jQueryHouse
Pick one. Some thing are rather getting through what is already available for free.
Maybe you are looking for
-
3D Touch does not work after update iOS 10 iMessage
I can't use Touch 3D to the message app. So I can't do the effects of texting
-
How can I change the position of a toolbar at the bottom to the top of the page?
Somehow, inadvertently, the toolbar of the URL has moved to the bottom of the page, what makes me crazy. Can someone tell me please how to move upwards again. This happened to me once before except he moved next to the page and I can't for the life o
-
Satellite P205D-S8804 - recovery disc for the necessary replacement
Hello I bought in June 08 a Toshiba Satellite P205D-S8804 on Ebay Australia and I now need to format the system but can not find my recovery disks which have been equipped with a system. Where can I order the necessary recovery discs go in Australia?
-
How can I delete an email stuck in my iPhone Mail cannot send to send a video?
How can I delete an email stuck in my iPhone Mail cannot send to send a video? Actually Mail attempts to send the e-mail and the ball rotates constantly. I have a feeling that it uses resources constantly. I do not have email. It can be removed. I j
-
Hello world I have an ICP accelerometer who need a constant current of 20mA 2. I decided to build my own package with a power source 24V/1, a diode and a capacitor. I want to know what the of could happen if I have a current of 1 a directly to the ac