How to use system recovery after OS change to the g4 pavilion 1305 to the

Similar Questions

• Satellite Pro U400-12y: how to use HDD recovery after the new installation of the OS

  Dear Sir

  I have the Satellite Pro U400-12y and give tem my friend use it when he gets back, the laptops it do format c: and reinstalled new windows.
  I try to do the recovery only by pressing f8 without answering.

  How can I recover my laptop to its state of origin as drive HARD recovery again in d:
  Thanks in adv

  Hello

  You will not be able to restore the factory settings because another operating system has been installed on the first partition.
  Usually by pressing F8 immediately after the laptop has been powered should allow the advanced on-screen menu. Here, you should choose option called repair my computer and Toshiba Recovery HARD drive.

  But if this doesn t work then you will not be able to use HARD drive recovery.
  In this case, you will need to order the new CD from here:

  https://backupmedia.Toshiba.EU/landing.aspx

  Good bye

• How to use product recovery CD-rom?

  How to use product recovery cd-rom on the satellite A40 range?

  Hi Daniel,.

  To use the recovery CD, simply insert the first CD (assuming there are two) in the CD drive and then just turn on your laptop while pressing the 'C' key on the keyboard. This will cause the laptop to load a minimal operating system on the CD that will start the process of recovery of the product.

  You should also be an initial menu that asks you if you want to do a complete system restore or restore 'Expert'. The full restore will delete all of your 'C' drive and will then install the entire system (excluding all the extras you'll have to install afterwards). The recovery of 'Expert' will allow you to partition your hard drive before you install the operating system in the C"" drive.

  Kind regards

• How to use data recovery in memory of "D"? The computer did not contain a wrioter of C/D, so I couldn't make a recovery disk.

  How to use data recovery in memory of 'd' (about 10 GB)?

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  Ask your manufacturer of computers for the EXACT method to restore to factory settings.

  This isn't their recovery process, Microsoft.

  See you soon. Mick Murphy - Microsoft partner

• I have 5 html pages that share a common header, footer and sidebar. How to use my navigation bar to change the content of the body without duplicating a lot of code?

  I have 5 html pages that share a common header, footer and sidebar. How to use my navigation bar to change the content of the body without duplicating a lot of code? Thank you!

  Read the help section of DW on models.

  Using Dreamweaver | Creating a Dreamweaver template

  Or use Server-Side Includes

  Nancy O.

• How to use < C:when test... inside the column in the table of the ADF

  I use ADF table with two columns
  in the first column, I check the Type of document is doc type so I have to use commondlink to download this file, otherwise I need to display only text.
  
  to this I added
  * < c:when test = "{boolean ($favoriteType eq 'doc')}" > *.
  that does not work.
  
  Please let me know how to use < C:when test... inside the column in the table of the ADF
  
  < tr:column sortProperty = "favoriteName" sortable = "true".
  headerText = "#{res ['favorite.favoritename ']}" "
  width = "500" noWrap = "false" >
  < c: choose >
  * < c:when test = "{boolean ($favoriteType eq 'doc')}" > *.
  < tr:commandLink actionListener = "#{bindings.downloadFile.execute} '"
  Text = "#{row.favoriteName} '"
  Disabled = "#{!}" Bindings.downloadFile.Enabled}"/ >
  < / c:when >
  < c: otherwise >
  < af:outputText value = "#{row.favoriteName}" / >
  < / c: otherwise >
  < / c: choose >
  < / tr:column >
  < tr:column sortProperty = "favoriteType" sortable = "true".
  headerText = "#{res ['favorite.favoriteType ']} ' rendering ="true">"
  < af:outputText value = "#{row.favoriteType}" id = "favoriteType" / > "
  < / tr:column >

  Hello

  I do not see, you use a Table of the ADF, but I see that you use Apache Trinidad. JSTL is executed analysis of time then that JSF is to render time, that's why it does not work what you see. Trinidad is a part of tr:switcher, and you can try this. Note that it doesn't ' r allow to change components by rank.

  Frank

• How can I stop my songs to change to the next song before finishing (on AppleTV)?

  How can I stop my songs to change to the next song before they ended?

  I don't think that apple TV has a setting of crossfade. The music is being heard from iTunes? In iTunes, this is defined in the preferences > reading.

  TT2

• How to use several adf 12 shape and insert the form data in to table during the click on "submit" button

  How to use several adf 12 shape and insert the form data in to table during the click on "submit" button. Can we use several form from adf or not?

  Make sure that you dragged the VO based EO.

  Also make sure that the VO attributes based EO Updatable property.

  The query according to VO is used only to add LOV to the column of the original VO ModelId.

  See you soon

  AJ

• Hello! I ve a problem with the complete abo... How can I activate illustrator after regulation time? the complete abo is already saved for the last month...

  Hello! I ve a problem with the complete abo... How can I activate illustrator after regulation time? the complete abo is already saved for the last month...

  [Duplicate message deleted... post the same question more than once is confusing... MOD]

  [This is an open forum, not a direct line to Adobe support... you have to wait a response]

  Hello

  Please see: -.

  https://helpx.Adobe.com/manage-account-membership/CC-reverts-to-trial.html

• in acrobat pro DC, I can't re - save files after making changes and the number appear in what looks like Arabic?

  in acrobat pro DC, I can't re - save files after making changes and the number appear in what looks like Arabic?, I run repair and rebooted the computer several times now...

  Ann Chinsang wrote:

  I can not re - save files

  Why? What is the procedure that you follow? What is the error message?

  Ann Chinsang wrote:

  number appear in what looks like the Arabic

  -What are you talking about? When you try to change the numbers in my document; it evolves in Arabic numerals

• How can I purchase just after effects cc, not the cloud all creative/package?

  How can I purchase just after effects cc, not the cloud all creative/package?

  You can get a simple app for 19.99 USD per month.

  Pricing plans and creative Cloud membership | Adobe Creative Cloud

  Mylenium

• After windows vista update, I can't left click the icon to start windows on the lower left toolbar. I have to use system restore to save updates until the start icon thaws. How can I fix it?

  If I right click on the start icon I can use explorer to access programs, but do not have access to stop, restart, etc.

  Hi, John Purcell, n.
   
  I you suggests that install you the update and then run sfc scan on the computer.

  Method 1:
  I suggest you to perform SFC scan on the computer.
  Scan SFC enforcement procedure:
  1. click on the Start button
  2. on the Start Menu, click all programs followed by accessories
  3. in the menu accessories, right-click on command line option
  4. in the drop-down menu that appears, click the "Run as Administrator" option
  5. If you have the User Account Control (UAC) enabled, you will be asked permission before the opening of the command line. You simply press the button continue if you are the administrator or insert password etc.
  6. in the command prompt window, type: sfc/scannow then press enter
  7. a message is displayed to indicate that "the analysis of the system will start.
  8. be patient because the analysis may take some time
  9. If all the files need replace SFC will replace them. You may be asked to insert your Vista DVD for this process to continue
  10. If all goes although you should, after the analysis, see the following message "Windows resource protection not found any breach of integrity.
  11. once the scan is finished, close the command prompt window, restart the computer and check.

  Additional information: how to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7: http://support.microsoft.com/kb/929833

  If this does not resolve the issue, uninstall the update and please post us and winodws update number.

  Thank you, and in what concerns:
  Shalini Surana - Microsoft technical support.
  Visit our Microsoft answers feedback Forumand let us know what you think.

• How to get system recovery disks

  original title: need to erase my hard drive to get rid of a virus, but the laptop did not come with disks in the system, because they were already installed on the laptop. What should I do?

  I bought a laptop computer three years ago and I had very little trouble with it. But recently, it has become very slow, even though I have plenty of hard drive on the left. When it's built in wifi suddenly stopped one day, that I took it to the geek squad in PC World, who told the driver he had been uninstalled and who, after having worked on my laptop and see how slow and it was slow, it was probably the result of a virus.

  I was told my only option to remove potential viruses was to back up my files and wipe my hard drive for all files. I was quoted £60 for this service so I went home and saved the files I wanted to keep on my laptop hard drive. I wiped my old PC hard drive before you delete the virus and I could then reinstall Windows and the built in programs using records systems. However, I bought this new laptop and all programs have been preinstalled and came with no system disk.

  What is the best way to go on my hard disk wiping programs and files without Windows, or should I just pay PC World to do properly?

  Thanks for the help :))

  When you clean your hard drive, it is wiped away.

  You must reinstall Windows during this process.

  Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Also ask them if it is possible to do the recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, Acer, recovery disk/s etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/default.aspx/KB/326246

  'How to replace Microsoft software or hardware, order service packs and upgrades, and replace product manuals'

  See you soon.

  Mick Murphy - Microsoft partner

• Equium L10: How to use Toshiba Recovery CD to install the OS

  Sorry in advance if this might be a stupid question, but I have not re-installed the operating system for years and don't know how to do.

  I think I need to reinstall cause i've got my laptop for almost 2 years and it became too slow with lots of error messages.

  Have Toshiba Equium L10 with Windows XP and a recovery DVD. The DVD contains Windows XP? Should I format my laptop first or just insert the DVD and follow the instructions?

  And after everything is done all the garbage will be gone and it will contain Windows XP only? And yet one thing I am concerned about my internet work later (I have a cable connected to the LAN) or I will have to do something?

  Thank you for all the advice!

  Hello Laura

  The previous user explained everything very well. For the new operating system installation you must use supplied recovery media. It contains BONES, all the drivers you need and also all Toshiba designed and utility tools.

  Procedure recovery takes about 20 minutes, but after that finish you'll still factory settings as the first day.

  Regarding your use of the Internet I can not tell you much, but try to connect LAN cable and you will see how it looks like.

• How fix a freezing problem after having changed a bad battery?

  My battery was unable to hold a charge, so I ordered a new one. After I replaced it, whenever I'm using my computer, it warms quickly (especially when I open an application) and the power runs about an hour. In addition, the entire system freezes randomly and I need either hold the power button to stop it or to let the power run out. When I reboot it, it shows "a disc should be checked for consistency. I have tried to install updates, removing unused applications and defraging the HDD.

  It is a big problem since I use this computer for work and need it to be upward and running smoothly as soon as possible.
  Help, please!

  Hello

  This could be a hardware problem caused by the battery, the charger/adapter a/c, or in the computer.

  Check with a real computer store (one that makes its own service internal leeks, not tip)
  at a Best Buy or other department stores) or system manufacturer support.

  -----------------------------------------------------------------------------------------------------------------------------------

  Methods to troubleshoot a software training (which can also help determine the possible causes of material).

  Use the startup clean and other methods to try to determine the cause of and eliminate
  the questions.

  ---------------------------------------------------------------

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out which files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">