How to write data files with dot-delimited values in the output interface

Similar Questions

• DASYLab how to write data to a file every 15 minutes

  Hi all

  I use dasylab and datashuttle/3000 to record data. What I want to do is to write data to a file every 15 minutes. I use the milti-file, which can write data to the file diffenret, but how do I control the timing, as the journal data every 15 minutes automatically.

  The other problem is that I use FFT analysis of the frequency spectrum. How can I determine the value of frequency where the peaks that happens.

  Thank you

  Write less data in the file that you have collected requires the reduction of certain data.

  There are three techniques to consider.

  With an average or an average of block - both reduce the data by using a function of averaging, defined in the module. To accomplish the reduction of data, choose block or RHM mode in the dialog box properties, and then enter the number of samples/data values that you want to reach on average.

  Average - when you reduce the data, you also should reblock data using the block length of the change in the output parameter. For example if you enjoy at 100 samples/second with a block size of 64, the average module configured on average, more than 10 samples will take 10 times longer to fill a block. The initial block represent 0.64 seconds, the output block represent 6.4 seconds at a sampling rate of 10 samples/second. If you change the size of output in one block, the program remains sensitive.

  Average block - average values in a block against each subsequent block, where the average is based position. The first samples are averaged, all second samples are average... etc. The output is a block of data, where each position has been averaged over the previous blocks. This is how you will be an average data FFT or histogram, for example, because the x-axis has been transformed in Hz or bins.

  Second technique - separate module. This allows to reduce the data and the effective sampling rate jumping blocks or samples. For example, to reduce the data in 1000 samples / second to 100 samples per second, configure the module to keep a sample, jumping 9, keep one, jumping 9, etc. If you configure to skip blocks, you will not reduce the sampling frequency, but will reduce the overall amount of data in a single block 9, for example. It is appropriate for the FFT data or histogram, for example, to have the context of the correct data.

  Finally, you can use a relay and a synchronization module module to control. For example, to reduce a sample data every 15 seconds, configure a generator module of TTL pulses for a cycle of 15 seconds of time. Connect it to a Combi trigger module and configure it to trigger on rising and stop the outbreak directly, with a trigger value after 1. The trigger output connects to the X of the relay command input.

  In addition to these techniques, you can change the third technique to allow a variable duration using a combination of other modules.

  Many of these techniques are covered in the help-tutorial-Quickstart, as the data reduction is one of the most frequently asked questions.

  In regards to the FFT... use the module of statistical values in order to obtain the Maximum and the Max Position. The Position of Max will be the value of the frequency associated with the Maximum value. The output of the statistics module is a single sample per block. Look at the different FFT sample installed in the worksheet calculation/examples folder.

• How to write data in mode intertwined with TDMS C DLL 2.0?

  Hello

  How to write data in mode intertwined with TDMS C DLL 2.0?

  I use DAQmx features in Visual Studio C++ without Measurment Studio.

  This function returns the data in interlaced mode.

  How can I configure the functions of DLL C TDMS to store this data in the tdms files?

  I see that it is not possible with the PDM version 2.0 with 1.0.

  Thank you

  -TDM C Dll is not able to do

  -TDM header writer may be usable for this but is not able to be used for tdms files.

• How to rename multiple files with the extension in windows xp

  How to rename multiple files with extension in windows XP.

  1. If you want to simply rename the extension, open a run window (Windows Logo key + R), type cmd and press ENTER. Using the CD (Change Directory) command, navigate to the folder in question. Now, type ren *.mp3, *.mp4, and press enter (note the two spaces in the command). Note, rename mp3 MP4 is just an example of the command.

  2. If you want to rename files, download the 32-bit version or 64-bit Bulk Rename, here http://www.bulkrenameutility.co.uk/Main_Intro.php

• How to open a file with a .wsx extension

  Original title: .wsx extentions?

  How to open a file with a .wsx extension

  Hello

  Where did you get the .wsx files?

  Please use your favorite search engine to find a program that can open the .wsx files.

• How to open a file with a .bar extension?

  Anyone know how to open a file with the .bar extension. I can't seem to find a way, and I get junk out of the web says that opens the file, but I find myself with toolbars and other things I don't need or want. Any help would be great. Thank you.

  On Sunday, February 12, 2012 21:12:54 + 0000, KevinAmosMDK wrote:

  Anyone know how to open a file with the .bar extension. I can't seem to find a way, and I get junk out of the web says that opens the file, but I find myself with toolbars and other things I don't need or want. Any help would be great. Thank you.

  See http://filext.com/file-extension/bar and note that
  http://FILExt.com/ is a very good place to look for answers to
  questions like this.
  Ken Blake, Microsoft MVP

• How to open a file with the extension .odg using Vista?

  How to open a file with the extension .odg using Vista?

  Hi Defiant503,

  Thank you for visiting the forums of answers.microsoft.com.

  I did some research and a file ending with .odg is an OpenDocument Document OpenOffice/StarOffice (Ver 2) of graphics by Sun Microsystems, Inc.    This means that in order to open this file, you will need this program to open it.  You will not be able to open this file with Vista.

  I hope this information helps.

  Kavita M
  Microsoft Answers Support Engineer
  Visit the Microsoft Answers Feedback Forum site
  and let us know what you think.

• How to write a file using BB 10 HTML5WebWorks

  Hello

  How to write a file using Blackberry 10 HTML5WebWorks API.

  https://developer.BlackBerry.com/HTML5/API/BlackBerry.IO.file.html#.SaveFile

  The example above does not work in BB 10.

  Please guide me.

  Of course, look at line 95 of this file:

  https://github.com/BlackBerry/BB10-WebWorks-samples/BLOB/master/invoke/invoker/invocations.js

• Cannot create a data file with a size of less than 1000 M

  Hello

  I have a problem that I can't solve. Whenever I try to create a DATA file with a size of less than 1000 MB, I get an ORA-03214

  Example:

  Select * from version of v$.

  Oracle Database 11 g Enterprise Edition Release 11.2.0.4.0 - 64 bit Production

  PL/SQL Release 11.2.0.4.0 - Production

  "CORE 11.2.0.4.0 Production."

  AMT for IBM/AIX RISC System/6000: Version 11.2.0.4.0 - Production

  NLSRTL Version 11.2.0.4.0 - Production

  -----

  ALTER TABLESPACE "IDX_PRETR1".

  ADD DATAFILE ' / appli/oracle/PR3/data4/TEST.dbf'

  SIZE 500 M;

  XXIX error on line 1 of the command:

  ALTER TABLESPACE "IDX_PRETR1".

  ADD DATAFILE ' / appli/oracle/PR3/data4/TEST.dbf'

  SIZE 500M

  Error report:

  SQL error: ORA-03214: the file size is less than the minimum required

  03214 00000 - "specified file size is smaller than the minimum required.

  * Cause: Specified for add/resize datafile/tempfile file size does not work

  provide the minimum required of an allocation unit.

  * Action: Increase the size of the file specification

  Thanks for the help and sorry for my English

  Hello

  The answer may lie in the INITIAL_EXTENT configuration in your space of tables, check DBA_tablespaces view.

  Also, try to use autoextend on and maxsize in your file data creation but better try with the highest value during the action of the mentioned error.

  Kind regards

  Juan M

• How can I block files with a certain file UCM 11 g extension

  Hello

  How can I block files with a certain extension of Oracle Webcenter content 11.1.1.8 file?

  There is another way by using filters. Click on the link below:

  http://sonaloraclewebcenter.blogspot.in/2015/04/UCM-limit-check-in-size-and-extension.html

  One suggested by Rajeev is the best solution. But you will still be able to record the files using the TELL. You just need to change the idocscript. Check the post below:

  http://sonaloraclewebcenter.blogspot.in/2015/04/UCM-validating-file-extension.html

• How to place data files in two places during duplication of database or refresh via RMAN test

  Hi all

  can you please find the solution and help me on this point

  How to place data files in two places during duplication of database or refresh via RMAN test

  Thank you

  Ran

  Hi all

  Please send me as soon as possible if you have a solution.

  Thank you.

  Ran

• Hi I need to know how to write Arabic text with indesign cc 2015

  Hi I need to know how to write Arabic text with indesign cc 2015

  One thing has changed: since CS6 (Version cloud only) you can install the operating system in Arabic or Hebrew any other language without extra cost.

• How to open a file with the extension x3f (sigma)

  How to open a file with the extension x3f (sigma)?

  Doesn't look good: Lightroom / Camera Raw: Sigma SD1 - when Merrill sensors will benefit, please!

• Automatic extension of a data file with the complete file system

  We are working on a database of Oracle10g 10.2.0.4 on HP - UX 11.31 (Itanium |) PA - RISC)
  
  We would create our database by activating the automatic Extension of our data files
  (defining the maximum size limit or unlimited)
  
  Our question is:
  What happens to the database in the event of complete file system when one of the data files should be automatically extended?
  The extended data file has become corrupted or the db cease its activity?
  
  
  Marco

  No data corruption should occur. If Oracle is trying to develop, OS it will send the message that it is not possible. That's all.

• How can I start firefox with new tab instead of the blank page?

  Today I've updated firefox to 13.0. I like the new 'new type '. I want to know how can I start firefox with new tab instead of the blank page?
  I don't want to change the home page to about: newtab.

  Sorry for my bad English.

  You can add about: newtab to the command line in the shortcut to the desktop Firefox to open this page on startup (target).

  • "C:\Program Files\Mozilla Firefox\firefox.exe"-new - tab on: newtab
  • https://developer.Mozilla.org/en/Command_Line_Options