HP 10 b 11: pension more

Similar Questions

• NI USB - 6501 OEM more sensitive to electromagnetic interference?

  We built a NI USB-6501 OEM card in a small instrument of office dedicated to switch ultrasonic impulses 300V between 3 transducers, using reed relays not shielded high-voltage controlled by the USB-6501 (using MOSFET transistors to drive the relay coils).  The end user reported that when he operated his ultrasonic transmitter at greater than 100 v voltages, USB-6501 would break (green "heartbeat" ceases, LabView or test panels lose communication with the interface).  Lower voltages to ultrasonic had no effect. Inspection of the 5vdc supply rails when running the pulse generator showed ears LOUD noise (surprise?), so we have recreated the box so that 1) optical isolation and no electrical connection between the USB-6501 and switching and 2) pension switching was surrounded by a 'box in the box '.   During a test, ultrasonic signals apparently still radiation enough so that the USB-6501 would break as before.

  Avoiding half measures, I mounted the USB-6501 in a completely separate extruded aluminum case (the land to the USB bus, but not to "taking" of land) with optical transmitters and optical fiber plastic 3' has been the only connection to the ultrasonic switch box (which is inside its own extruded aluminum case).

  This made things better: the USB-6501 would work for a while when the ultrasonic signals were present but still crashes after a few minutes.  In addition, reports researcher that starting the engine w / controller in immediate proximity to this interface also immediately causes a crash of the USB-6501.

  Right now I do more optical cables and confirmed that the USB-6501 works thankfully when he is simply the engine optical transmitters with no ultrasonic signals in the area.  I'm surprised that this digital i/o interface seems so sensitive to environmental disturbances.

  We made sure that 1) was based on the shield of the cable USB ONLY at the end of the PC, according to the specification USB;  2) cable USB was of ferrite chokes to make it less

  an antenna 'noise' 3 the Board 6501 had connected logic ground the housing in aluminium, and 4) we have equipped the case with a pattern important

  cable and clamp to connect to a 'true' of the Earth.

  When the end user has reported that there were still problems, I went to his lab and discovered

  He assumes that hang on a couple of wires ground wire, to a strain gauge, which was stuck on a piece of 3' of the railway, itself sitting on a wooden table

  no electricity whatsoever, what meant it was "founded".  After that I am makes me sputter and him look staring in disbelief, we plugged into an electrical conduit nearby,

  and all of a sudden, the problem disappeared.

  I'm glad it works now, but the fact that turn on an instrument of motor stepper located three feet of 6501 can crash against interference if)

  the case is not grounded), stillsurprises me.  I expect to use 6501 in other instruments, it will take extra precautions on the armor.

• UK Public sector: Teachers Pension Patch and functional facility

  Hello
  
  I have a question about installing functional meanings. (I'm assuming that / awaits the response of those who have made this setup already and they know / gone thorugh the Readme for the patch)
  
  I try to use the code provided in the patch Readme to findout good level for the pension contributions... To do this, I need the annual salary FTES within the fast formula.
  
  
  
  The patch readme says:
  
  
  Once the formula has recovered the contribution rates for retirement, it must be
  applied to the real wage in the period.
  
  l_tps_emp_contr_sal = FULL_TIME_ANNUAL_SALARY_TPS_ASG_TRANSFER_PTD
  
  
  However, I'm getting zero value for FULL_TIME_ANNUAL_SALARY_TPS_ASG_TRANSFER_PTD.
  
  that is, zero l_tps_emp_contr_sal that is passed to
  
  l_EE_Contribution_Percent = to_number (GET_TABLE_VALUE
  ("PQP_TPA_PENSIONABLE_PAY_RANGE",
  "Employee contribution rate."
  TO_CHAR (l_tps_emp_contr_sal)))
  
  
  and nothing is coming...
  
  
  How can I get the correct value of FULL_TIME_ANNUAL_SALARY_TPS_ASG_TRANSFER_PTD?
  
  
  
  The readme says next
  
  
  -----------------------------------------------------------------------------
  FTE/salary amount
  -----------------------------------------------------------------------------
  
  The annual salary is the equivalent gross salary full time based on which the
  band must be decided. There may be several items by assignment that
  could be populating this value and each item can have different
  configurations, for example:
  a. element can have an annual value where a period is calculated
  b. period amount to pay
  
  The above, it can still rank based on
  a. use of the model of work or hours of work
  b. full-time salary
  c. part-time salary.
  
  a. a payment of time which annualization cannot be applied, but should FTES
  be applied.
  (b) a payment of time on which annualization may be applied but FTE must
  applies do not.
  c. annual value to which FTES should be applied.
  d. annual value on which ETP should not apply
  
  There are many more variations in the scenarios described above.
  To perform the calculation of the annual salary gross full-time equivalents
  for all possible scenarios, the seeded element FTES annualized pay must be
  used by the client.
  
  So that the Pension contribution rate to be determined, the annual FTES
  effective treatment for the period in question, must be available.
  It is assumed that the value of the FTES will be available for current items
  that the client uses to pay teachers because it would be necessary to determine
  the value of the actual payment for the period.
  This value will be fed to the stocked item (annualized compensation of FTES) by the
  formula for the individual item.
  
  ------------------------------------------------------------------------------
  Changes proposed for the determination of the annual value full time:
  ------------------------------------------------------------------------------
  
  Suggested changes to the formula of elements to determine the annual value full time:
  The following instructions must be added to the existing compensation element
  formula. Here are the changes suggested to existing formulas to derive the
  Annual salary of FTE.
  Case 1: If the form element has access to the annual value of FTES.
  
  return_Annual_inf = ANNUAL_VALUE
  
  / * Assign the annual value of FTES for this element to the return_Annual_inf variable * /.
  Case 2: If the form element has access to only to the period of value and
  Annual value of FTE is not stored anywhere.
  
  return_Annual_inf = (PERIOD_VALUE * PAY_STATUTORY_ANNUAL_PERIODS)
  
  / * Assign the full period time value for this element multiplied by the standard
  DBI for the annual periods to local variable return_Annual_inf * /.
  Case 3: If the form element has access to only time partial annual value
  and annual FTE value is not stored anywhere.
  
  return_Annual_inf = ANNUAL_VALUE / ASG_FTE_VALUE
  
  / * Assign the full period time value for this element multiplied by the standard
  DBI for the annual periods to local variable return_Annual_inf * /.
  Box 4: If the form element has access to only part of the period time value
  and annual FTE value is not stored anywhere.
  
  return_Annual_inf =(PERIOD_VALUE*PAY_STATUTORY_ANNUAL_PERIODS)/ASG_FTE_VALUE
  
  / * Assign the full period time value for this element multiplied by the standard
  DBI for the annual periods then divided by DBI standard for TVE at the local level
  return_Annual_inf variable * /.
  
  Note:
  The new local variable return_annual_inf must be returned to formula for
  the new piece of planted information FTES annualized pay.

  You mean, where is the formula results screen? It is to:

  Total compensation--> basic--> formula results

  Enter the name of the element "Annual salary" or be it in the area of the element, and then choose the search"" button.

  You should see the formula (probably with a 'Standard' rule against him) and the existing rules of the result of the formula in the lower window.

  You must create a new rule in this bottom window - what was called the new return form variable, should be selected in the drop-down list. Then choose "Indirect result", then choose the item 'FTES annualized compensation' as the target element, with the entry name 'Value to pay', and then 'save '. You should be off and running then.

  Hope that helps

  Clive

• iPhone 7 more - IOS 10.2

  Recently, I just got my iPhone more than 7. Once I opened it started the update to iOS 10.0.2

  If after that it worked I checked the camera looking for the portrait fearure but he isn't here! How can I have?

  In addition, the device is slow and hanging out!

  Thank you

  Any comment yet!

• Appeal iPhone issues 7 more

  I recently bought the new iPhone 7 more.  Not only am I having problems with the LTE service, bounce back between 3 G and no service I am now having problems with call connectivity.  When you try to make an outgoing call, I get an automatic response from my carrier (Verizon) "it's Verizon, we are unable to complete your call at this time, please turn off your phone and back and try again."

  It is a known issue with the iPhone 7 and Verizon. Supposed to be Apple and Verizon are seeking him. It has been a problem since the phone was released. Do a Google search or search here on the forums for a temporary solution but not a cure.  But basically to stop the LTE oice and data into data only in the settings.

• Background app colors are more uniform

  Since the upgrade of the Sierra, web pages Chrome and the code editor backgrounds Atom are messy. For example, in the atom, it seems that I've highlighted throughout the text, part of the background is dark and some of it is lighter. In Chrome, bluish grey background of Facebook will be uniform and then become clearer on the sides abruptly. This sudden change happens on other colors, which actually look as if I chose the parts of the page with my cursor. Basically the uniform color of the origins on some Web pages or applications (Atom and Chrome) are more uniform.

  This substantive change only happens when I plug my HDMI cable on an external monitor. If I'm working on all of my macbook pro retina screen, everything seems fine. If I plug in my HDMI cable to an external monitor, the sets become non-uniform, even on the macbook pro (when mirroring) of the screen. I used the HDMI cable and the monitor with another computer and the problem does not exist, so I think it has something to do with macOS Sierra. Strangely enough, this problem only occurs with Atom and Chrome. Safari, for example, is absolutely perfect.

  I've included screenshots to show what I mean.

  Hi tedmcdo,

  Thanks for the upgrade to Mac OS Sierra! It seems like when you connect your external monitor to your Mac via HDMI, the Mac knows uniform color schemes. If this only happens when the external monitor is connected, you can try the reset NVRAM while it is disconnected from your Mac.
  
  

  What is NVRAM?

  A small amount of memory on your computer called "non-volatile random - access memory" or NVRAM, stores certain settings in a location that OS X can access quickly. Settings that are stored in NVRAM are dependent on the type of Mac you use and the types of devices on it.

  Information stored in the NVRAM may include:

  • The speaker volume
  • Screen resolution
  • Selection of boot drive
  • These latest panic the kernel, if applicable

  If you encounter problems with these features, you may need to reset the NVRAM on your computer. For example, if your Mac starts up from a bootdisk other than that specified in startup disk preferences, or a question mark icon appears briefly at the start of your Mac.

  How to reset the NVRAM on your Mac.

  After resetting the NVRAM, please connect the screen and check if the problem is resolved. Alternatively, you can try to boot your Mac in safe mode.
  

  What is safe mode?

  Safe mode (sometimes called secure boot) is a way to start up your Mac so that it performs certain checks and prevents certain software from loading automatically or opening. From your Mac in safe mode does the following:

  • Check your startup disk and attempts to fix problems if necessary directory
  • Loads needed kernel extensions only
  • Prevents elements start and the login items open automatically
  • Disables the user installed fonts
  • Delete font caches, hiding the kernel and other files of the system cache

  Together, these changes can help resolve or isolate issues related to your startup disk.

  Try safe mode if your Mac does not end commissioning

  Please use the Apple Support communities to post your question. These procedures should have your Mac showing its vibrant colors on the Retina display as expected. Good day.

• iPhone 6s more 'Phone noise cancelling' setting Grayed Out

  I have a 6 more than 128 GB iPhone running iOS 10.0.2. I can't activate the 'Phone noise cancelling' setting in settings > general > accessibility > telephone noise cancelling because it is grayed out. I have attached a screenshot for reference.

  I've tried hard restart my iPhone (Home + Power button) without success. Any help is very appreciated! Thank you.

  

  Hey there, Stephen Bond,.

  Thank you for using communities of support from Apple! I see from your post that your iPhone more 6s on iOS 10.0.2 does not work as expected because the cancellation of noise from phone toggle is grayed out. I'll be happy to help you.

  First check to see if the hearing aid Mode is enabled in settings > general > accessibility > hearing aids. If this option is enabled, then telephone noise cancelling will be grayed out as you describe. If this isn't the case and that the option is grayed out, please continue.

  How to back up your iPhone, iPad and iPod touch - please backup your iPhone to ensure that your personal information is safe.

  Use iTunes on your Mac or PC to restore the iPhone, iPad or iPod to factory settings - this process will completely erase the iPhone to allow a new copy of the iOS to install. The first time, select "set up as a new iPhone. Once your iPhone is back to the home screen, check the setting of the new. If everything works as it should, use the "restore from backup" link in the section «Get help» If it is not, under the same article, "Contact Apple Support".

  Take care and have a great day!

• iPhone 7 more telephoto camera does not

  Is anyone having problems with iPhone 7 more telephoto does not activate. I'll go to the camera application and press the 2 x zoom feature, but it appears to be not to activate the camera of 56mm at the front. I cover the lens with my finger, the camera on the right side and the iPhone always displays an image despite me concealing one of the cameras teo. I can't activate the second camera. It seems to only be zooming digitally. I'll do this outside and he'll only digitally zoom when I hide the second lens.

  Im having this same problem. I heard from someone that he could not work until the next software update... but I have no idea and have not found anything in the online help. If someone else gets to know how.

• "Sit less, move more.

  The new IOS 10.0.2 has modified the application of health by adding a video called "sit less, move more" section of health data. Although I agree with the feeling and I'm even happy to be preached about this TIME, he began to grate. Can I remove or ignore?

  Do not watch the video.  Scroll the screen to see your activity data.

• is it possible to buy the iPhone 7 more unlocked and without a subscription which will work in Russia

  My friend is going to go to New York for the holidays of the maintains 21 October to 31 October. And I really want to buy the iPhone 7 more 128Gb it. I know that I need a free sim card or without a contract. I asked best buy about this and they said they don't sell iPhones with contracrs. Is this possible?

  Thank you.

  Apple has not announced when they will start to sell the iPhone Unlocked 7.

• IPhone 6 more flashing screen

  After updating my iphone 6 more with ios10, the start flickering from the top screen and the buttons does not. stil phonse looking again, does not fall and there is not a single crash. It has already expired the warrently, I understand that there are a lot of people the same proplem faceing. We can hangout or Exchange the phone to Apple.

  Hello

  First consider trying the following steps:

  • Back up your iPhone (you can encrypt the backup if you use iTunes):
    • The backup of your iPhone, iPad and iPod touch - Apple Support
  • Restore it to the factory settings, with a new copy of iOS:
    • Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod settings - Apple Support
  • Check if the glitch / question reappears before or after restoring the backup:
    • Restore your iPhone, iPad or iPod touch from a backup - Apple Support

  If the problem persists (or if you prefer to skip this step), contact Apple support (mail service may be available) or make a Genius Bar reservation in order to have your iPhone verified and, if recommended by Apple, served:

  • Contact - Support official Apple
  • https://Twitter.com/applesupport
  • http://www.Apple.com/retail/Geniusbar/

• more secure e-mail provider

  Who offers the safer more secure messaging service on the internet?

  I would definitely say iCloud email provider is the most sure/more secure.

• iPhone 6s more does not accept the password for the first time

  All of a sudden my iphone 6 s more, will not recognize and accept my password.

  First screen says: "enter code". "Touch ID requires your access code when you restart the Iphone."

  Question... is equivalent to a 'code' a 'password'?

  Why she would accept my password and then 30 minutes later he rejects?

  Any ideas would be very appreciated.

  Ray

  Maybe nobody over there wants to take this question!

• Iphone6 more

  Iphone6 more, unable to save pictures from emails.  Save image button disappeared

  Hi david18421,

  Looks like you are having some problems with saving image attachments in your emails. Please follow the steps below to save a photo or video of an attachment in Mail.
  

  Save a picture or video to Photos. Tap the photo or video, then press look. Press on , then click on Save Image.

  Spare - part iPhone

  Please use the Apple Support communities to post your question. This should help you get these saved attachments. Good day.

• How can I update my iPhone more than 8.4 of iOS iOS 9.3.5 6?

  How can I update my iPhone more than 8.4 of iOS iOS 9.3.5 6?

  You do not have. You can only upgrade to the current version which is 10.0.2